mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-22 06:57:57 +00:00
ipq807x: add support for Compex WPQ873
The Compex WPQ873 is a development board with two M.2 B-key
slots for cellular modems.
Device info:
- IPQ8072A SoC
- 512MiB RAM
- 256MiB NAND flash
- 8MiB SPI NOR
- 3x 1GigE ports
- 1x 2.5GigE port
- 2.4GHz/5GHz AX WLAN
- 1x USB 3.0 port
- 1x M.2 B-key socket with PCIe 3.0
- 1x M.2 B-key socket with PCIe 2.0 and USB 3.0
- 4x SIM card slots
- Bluetooth LE 5.0 (QCA4024)
Prerequisites
1) TFTP server
2) 3.3V USB to TTL cable for UART console
2.54mm pitch 4-pin header for UART is readily provided on board, no modifications are necessary to access it
TTL connector pinout: 2=TX, 3=RX, 4=GND
Arrow marks pin 1 which is 3.3V
Serial port settings: 115200 8N1 no flow control
The device will most likely ship with a QSDK-based firmware.
1. Power on device and interrupt u-boot to obtain u-boot CLI
2. set serverip to IP address of the TFTP server, for example:
`setenv serverip 192.168.1.10`
3. Download image from TFTP server:
`tftpboot 0x44000000 openwrt-ipq807x-generic-compex_wpq873-squashfs-factory.ubi`
4. Flash ubi image to both partitions and reset:
`sf probe
imxtract 0x44000000 ubi
nand device 0
nand erase 0x0 0x3400000
nand erase 0x3c00000 0x3400000
nand write $fileaddr 0x0 $filesize
nand write $fileaddr 0x3c00000 $filesize
reset`
Afterwards, you can use sysupgrade to flash new OpenWRT images.
Signed-off-by: Antti Nykänen <antti.nykanen@nokia.com>
This commit is contained in:
Antti Nykänen
parent
c815ecdebd
commit
07c45c0859
@ -14,6 +14,7 @@ netgear,wax218)
|
||||
[ -n "$idx" ] && \
|
||||
ubootenv_add_uci_config "/dev/mtd$idx" "0x0" "0x40000" "0x20000" "2"
|
||||
;;
|
||||
compex,wpq873|\
|
||||
edgecore,eap102|\
|
||||
zyxel,nbg7815)
|
||||
idx="$(find_mtd_index 0:appsblenv)"
|
||||
|
||||
@ -28,6 +28,7 @@ ipq807x_setup_interfaces()
|
||||
qnap,301w)
|
||||
ucidef_set_interfaces_lan_wan "lan1 lan2 lan3 lan4 10g-2" "10g-1"
|
||||
;;
|
||||
compex,wpq873|\
|
||||
redmi,ax6|\
|
||||
xiaomi,ax3600)
|
||||
ucidef_set_interfaces_lan_wan "lan1 lan2 lan3" "wan"
|
||||
|
||||
@ -10,6 +10,7 @@ case "$FIRMWARE" in
|
||||
"ath11k/IPQ8074/hw2.0/cal-ahb-c000000.wifi.bin")
|
||||
case "$board" in
|
||||
buffalo,wxr-5950ax12|\
|
||||
compex,wpq873|\
|
||||
edgecore,eap102|\
|
||||
edimax,cax1800|\
|
||||
dynalink,dl-wrx36|\
|
||||
|
||||
@ -66,6 +66,7 @@ platform_do_upgrade() {
|
||||
fw_setenv upgrade_available 1
|
||||
nand_do_upgrade "$1"
|
||||
;;
|
||||
compex,wpq873|\
|
||||
edimax,cax1800|\
|
||||
netgear,wax218)
|
||||
nand_do_upgrade "$1"
|
||||
|
||||
@ -0,0 +1,487 @@
|
||||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
/* Copyright 2023 Nokia */
|
||||
|
||||
/dts-v1/;
|
||||
|
||||
#include "ipq8074.dtsi"
|
||||
#include "ipq8074-hk-cpu.dtsi"
|
||||
#include "ipq8074-ess.dtsi"
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/input/input.h>
|
||||
#include <dt-bindings/leds/common.h>
|
||||
|
||||
/ {
|
||||
model = "Compex WPQ873";
|
||||
compatible = "compex,wpq873", "qcom,ipq8074";
|
||||
|
||||
aliases {
|
||||
serial0 = &blsp1_uart5;
|
||||
led-boot = &led_power_blue;
|
||||
led-failsafe = &led_power_red;
|
||||
led-running = &led_system_green;
|
||||
led-upgrade = &led_system_blue;
|
||||
/* Aliases as required by u-boot to patch MAC addresses */
|
||||
ethernet0 = &dp6;
|
||||
ethernet1 = &dp2;
|
||||
ethernet2 = &dp3;
|
||||
ethernet3 = &dp4;
|
||||
label-mac-device = &dp6;
|
||||
};
|
||||
|
||||
chosen {
|
||||
stdout-path = "serial0:115200n8";
|
||||
bootargs-append = " root=/dev/ubiblock0_1";
|
||||
};
|
||||
|
||||
keys {
|
||||
compatible = "gpio-keys";
|
||||
|
||||
reset {
|
||||
label = "reset";
|
||||
gpios = <&tlmm 21 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_RESTART>;
|
||||
};
|
||||
};
|
||||
|
||||
leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
led_power_red: power-red {
|
||||
label = "red:power";
|
||||
gpios = <&tlmm 42 GPIO_ACTIVE_HIGH>;
|
||||
color = <LED_COLOR_ID_RED>;
|
||||
};
|
||||
|
||||
led_power_blue: power-blue {
|
||||
label = "blue:power";
|
||||
gpios = <&tlmm 43 GPIO_ACTIVE_HIGH>;
|
||||
color = <LED_COLOR_ID_BLUE>;
|
||||
};
|
||||
|
||||
led_system_red: system-red {
|
||||
label = "red:system";
|
||||
gpios = <&tlmm 28 GPIO_ACTIVE_HIGH>;
|
||||
color = <LED_COLOR_ID_RED>;
|
||||
};
|
||||
|
||||
led_system_green: system-green {
|
||||
label = "green:system";
|
||||
gpios = <&tlmm 18 GPIO_ACTIVE_HIGH>;
|
||||
color = <LED_COLOR_ID_GREEN>;
|
||||
};
|
||||
|
||||
led_system_blue: system-blue {
|
||||
label = "blue:system";
|
||||
gpios = <&tlmm 19 GPIO_ACTIVE_HIGH>;
|
||||
color = <LED_COLOR_ID_BLUE>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&tlmm {
|
||||
mdio_pins: mdio-pins {
|
||||
mdc {
|
||||
pins = "gpio68";
|
||||
function = "mdc";
|
||||
drive-strength = <8>;
|
||||
bias-pull-up;
|
||||
};
|
||||
|
||||
mdio {
|
||||
pins = "gpio69";
|
||||
function = "mdio";
|
||||
drive-strength = <8>;
|
||||
bias-pull-up;
|
||||
};
|
||||
};
|
||||
|
||||
i2c_pins: i2c-pins {
|
||||
pins = "gpio0", "gpio2";
|
||||
function = "blsp5_i2c";
|
||||
drive-strength = <8>;
|
||||
bias-disable;
|
||||
};
|
||||
};
|
||||
|
||||
&blsp1_uart5 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&blsp1_i2c6 {
|
||||
status = "okay";
|
||||
|
||||
pinctrl-0 = <&i2c_pins>;
|
||||
pinctrl-names = "default";
|
||||
};
|
||||
|
||||
&prng {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&cryptobam {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&crypto {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&qpic_bam {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&blsp1_spi1 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&tlmm {
|
||||
mdio_pins: mdio-pins {
|
||||
mdc {
|
||||
pins = "gpio68";
|
||||
function = "mdc";
|
||||
drive-strength = <8>;
|
||||
bias-pull-up;
|
||||
};
|
||||
|
||||
mdio {
|
||||
pins = "gpio69";
|
||||
function = "mdio";
|
||||
drive-strength = <8>;
|
||||
bias-pull-up;
|
||||
};
|
||||
};
|
||||
|
||||
button_pins: button_pins {
|
||||
reset_button {
|
||||
pins = "gpio66";
|
||||
function = "gpio";
|
||||
drive-strength = <8>;
|
||||
bias-pull-up;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&blsp1_spi1 {
|
||||
status = "okay";
|
||||
|
||||
flash@0 {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
reg = <0>;
|
||||
compatible = "jedec,spi-nor";
|
||||
spi-max-frequency = <50000000>;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "0:sbl1";
|
||||
reg = <0x0 0x50000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@50000 {
|
||||
label = "0:mibib";
|
||||
reg = <0x50000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@60000 {
|
||||
label = "0:bootconfig";
|
||||
reg = <0x60000 0x20000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@80000 {
|
||||
label = "0:bootconfig1";
|
||||
reg = <0x80000 0x20000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@a0000 {
|
||||
label = "0:qsee";
|
||||
reg = <0xa0000 0x180000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@220000 {
|
||||
label = "0:qsee_1";
|
||||
reg = <0x220000 0x180000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@3a0000 {
|
||||
label = "0:devcfg";
|
||||
reg = <0x3a0000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@3b0000 {
|
||||
label = "0:devcfg_1";
|
||||
reg = <0x3b0000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@3c0000 {
|
||||
label = "0:apdp";
|
||||
reg = <0x3c0000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@3d0000 {
|
||||
label = "0:apdp_1";
|
||||
reg = <0x3d0000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@3e0000 {
|
||||
label = "0:rpm";
|
||||
reg = <0x3e0000 0x40000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@420000 {
|
||||
label = "0:rpm_1";
|
||||
reg = <0x420000 0x40000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@460000 {
|
||||
label = "0:cdt";
|
||||
reg = <0x460000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@470000 {
|
||||
label = "0:cdt_1";
|
||||
reg = <0x470000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@480000 {
|
||||
label = "0:appsblenv";
|
||||
reg = <0x480000 0x10000>;
|
||||
};
|
||||
|
||||
partition@490000 {
|
||||
label = "0:appsbl";
|
||||
reg = <0x490000 0xa0000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@550000 {
|
||||
label = "0:appsbl_1";
|
||||
reg = <0x530000 0xa0000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@610000 {
|
||||
label = "0:art";
|
||||
reg = <0x5d0000 0x40000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@650000 {
|
||||
label = "0:ethphyfw";
|
||||
reg = <0x610000 0x80000>;
|
||||
read-only;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&qpic_nand {
|
||||
status = "okay";
|
||||
|
||||
nand@0 {
|
||||
reg = <0>;
|
||||
nand-ecc-strength = <8>;
|
||||
nand-ecc-step-size = <512>;
|
||||
nand-bus-width = <8>;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "rootfs";
|
||||
reg = <0x0000000 0x3400000>;
|
||||
};
|
||||
|
||||
partition@3400000 {
|
||||
label = "0:wififw";
|
||||
reg = <0x3400000 0x800000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@3c00000 {
|
||||
label = "rootfs_1";
|
||||
reg = <0x3c00000 0x3400000>;
|
||||
};
|
||||
|
||||
partition@7000000 {
|
||||
label = "0:wififw_1";
|
||||
reg = <0x7000000 0x800000>;
|
||||
read-only;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&qusb_phy_0 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&qusb_phy_1 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&ssphy_0 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&ssphy_1 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usb_0 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usb_1 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
|
||||
&mdio {
|
||||
status = "okay";
|
||||
pinctrl-0 = <&mdio_pins>;
|
||||
pinctrl-names = "default";
|
||||
reset-gpios = <&tlmm 37 GPIO_ACTIVE_LOW>;
|
||||
|
||||
qca8075_1: ethernet-phy@1 {
|
||||
compatible = "ethernet-phy-ieee802.3-c22";
|
||||
reg = <1>;
|
||||
};
|
||||
|
||||
qca8075_2: ethernet-phy@2 {
|
||||
compatible = "ethernet-phy-ieee802.3-c22";
|
||||
reg = <2>;
|
||||
};
|
||||
|
||||
qca8075_3: ethernet-phy@3 {
|
||||
compatible = "ethernet-phy-ieee802.3-c22";
|
||||
reg = <3>;
|
||||
};
|
||||
|
||||
qca8081: ethernet-phy@28 {
|
||||
compatible = "ethernet-phy-ieee802.3-c22";
|
||||
reg = <28>;
|
||||
reset-gpios = <&tlmm 44 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
};
|
||||
|
||||
&switch {
|
||||
status = "okay";
|
||||
|
||||
switch_cpu_bmp = <0x1>; /* cpu port bitmap */
|
||||
switch_lan_bmp = <0x3e>; /* lan port bitmap */
|
||||
switch_wan_bmp = <0x40>; /* wan port bitmap */
|
||||
switch_mac_mode = <0x0>; /* mac mode for uniphy instance0*/
|
||||
switch_mac_mode1 = <0x0f>; /* mac mode for uniphy instance1*/
|
||||
switch_mac_mode2 = <0x0f>; /* mac mode for uniphy instance2*/
|
||||
bm_tick_mode = <0>; /* bm tick mode */
|
||||
tm_tick_mode = <0>; /* tm tick mode */
|
||||
|
||||
qcom,port_phyinfo {
|
||||
port@2 {
|
||||
port_id = <2>;
|
||||
phy_address = <1>;
|
||||
};
|
||||
port@3 {
|
||||
port_id = <3>;
|
||||
phy_address = <2>;
|
||||
};
|
||||
port@4 {
|
||||
port_id = <4>;
|
||||
phy_address = <3>;
|
||||
};
|
||||
port@5 {
|
||||
port_id = <6>;
|
||||
phy_address = <28>;
|
||||
port_mac_sel = "QGMAC_PORT";
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&edma {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&dp2 {
|
||||
status = "okay";
|
||||
phy-handle = <&qca8075_1>;
|
||||
label = "lan1";
|
||||
};
|
||||
|
||||
&dp3 {
|
||||
status = "okay";
|
||||
phy-handle = <&qca8075_2>;
|
||||
label = "lan2";
|
||||
};
|
||||
|
||||
&dp4 {
|
||||
status = "okay";
|
||||
phy-handle = <&qca8075_3>;
|
||||
label = "lan3";
|
||||
};
|
||||
|
||||
&dp6 {
|
||||
status = "okay";
|
||||
phy-handle = <&qca8081>;
|
||||
label = "wan";
|
||||
};
|
||||
|
||||
&pcie_qmp0 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&pcie0 {
|
||||
status = "okay";
|
||||
|
||||
perst-gpio = <&tlmm 58 GPIO_ACTIVE_LOW>;
|
||||
|
||||
bridge@0,0 {
|
||||
reg = <0x00020000 0 0 0 0>;
|
||||
#address-cells = <3>;
|
||||
#size-cells = <2>;
|
||||
ranges;
|
||||
};
|
||||
};
|
||||
|
||||
&pcie_qmp1 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&pcie1 {
|
||||
status = "okay";
|
||||
|
||||
perst-gpio = <&tlmm 62 GPIO_ACTIVE_HIGH>;
|
||||
|
||||
bridge@1,0 {
|
||||
reg = <0x00010000 0 0 0 0>;
|
||||
#address-cells = <3>;
|
||||
#size-cells = <2>;
|
||||
ranges;
|
||||
};
|
||||
};
|
||||
|
||||
&wifi {
|
||||
status = "okay";
|
||||
|
||||
qcom,ath11k-calibration-variant = "Compex-WPQ873";
|
||||
};
|
||||
@ -31,6 +31,19 @@ define Device/buffalo_wxr-5950ax12
|
||||
endef
|
||||
TARGET_DEVICES += buffalo_wxr-5950ax12
|
||||
|
||||
define Device/compex_wpq873
|
||||
$(call Device/FitImage)
|
||||
$(call Device/UbiFit)
|
||||
DEVICE_VENDOR := Compex
|
||||
DEVICE_MODEL := WPQ873
|
||||
BLOCKSIZE := 128k
|
||||
PAGESIZE := 2048
|
||||
DEVICE_DTS_CONFIG := config@hk09.wpq873
|
||||
SOC := ipq8072
|
||||
IMAGE/factory.ubi := append-ubi | qsdk-ipq-factory-nand
|
||||
endef
|
||||
TARGET_DEVICES += compex_wpq873
|
||||
|
||||
define Device/dynalink_dl-wrx36
|
||||
$(call Device/FitImage)
|
||||
$(call Device/UbiFit)
|
||||
|
||||
Loading…
Reference in New Issue
Block a user