ipq4019: add support for ZTE MF287+ aka DreiNeo

The ZTE MF287+ is a LTE router used (exclusively?) by the network operator
"3". The MF287 (i.e. non-plus aka 3Neo) is also supported (the only
difference is the LTE modem)

Specifications
==============

SoC: IPQ4018
RAM: 256MiB
Flash: 8MiB SPI-NOR + 128MiB SPI-NAND
LAN: 4x GBit LAN
LTE: ZTE Cat12 (MF287+) / ZTE Cat6 (MF287)
WiFi: 802.11a/b/g/n/ac SoC-integrated

MAC addresses
=============

LAN: from config + 2
WiFi 1: from config
WiFi 2: from config + 1

Installation
============

Option 1 - TFTP
---------------

TFTP installation using UART is preferred. Disassemble the device and
connect serial. Put the initramfs image as openwrt.bin to your TFTP server
and configure a static IP of 192.168.1.100. Load the initramfs image by
typing:

  setenv serverip 192.168.1.100
  setenv ipaddr 192.168.1.1
  tftpboot 0x82000000 openwrt.bin
  bootm 0x82000000

From this intiramfs boot you can take a backup of the currently installed
partitions as no vendor firmware is available for download:

  ubiattach -m14
  cat /dev/ubi0_0 > /tmp/ubi0_0
  cat /dev/ubi0_1 > /tmp/ubi0_1

Copy the files /tmp/ubi0_0 and /tmp/ubi0_1 somewhere save.

Once booted, transfer the sysupgrade image and run sysupgrade. You might
have to delete the stock volumes first:

  ubirmvol /dev/ubi0 -N ubi_rootfs
  ubirmvol /dev/ubi0 -N kernel

Option 2 - From stock firmware
------------------------------

The installation from stock requires an exploit first. The exploit consists
of a backup file that forces the firmware to download telnetd via TFTP from
192.168.0.22 and run it. Once exploited, you can connect via telnet and
login as admin:admin.

The exploit will be available at the device wiki page.

Once inside the stock firmware, you can transfer the -factory.bin file to
/tmp by using "scp" from the stock frmware or "tftp".

ZTE has blocked writing to the NAND. Fortunately, it's easy to allow write
access - you need to read from one file in /proc. Once done, you need to
erase the UBI partition and flash OpenWrt. Before performing the operation,
make sure that mtd13 is the partition labelled "rootfs" by calling
"cat /proc/mtd".

Complete commands:

  cd /tmp
  tftp -g -r factory.bin 192.168.0.22
  cat /proc/driver/sensor_id
  flash_erase /dev/mtd13 0 0
  dd if=/tmp/factory.bin of=/dev/mtdblock13 bs=131072

Afterwards, reboot your device and you should have a working OpenWrt
installation.

Restore Stock
=============

Option 1 - via UART
-------------------

Boot an OpenWrt initramfs image via TFTP as for the initial installation.
Transfer the two backed-up files to your box to /tmp.

Then, run the following commands - replace $kernel_length and $rootfs_size
by the size of ubi0_0 and ubi0_1 in bytes.

  ubiattach -m 14
  ubirmvol /dev/ubi0 -N kernel
  ubirmvol /dev/ubi0 -N rootfs
  ubirmvol /dev/ubi0 -N rootfs_data
  ubimkvol /dev/ubi0 -N kernel -s $kernel_length
  ubimkvol /dev/ubi0 -N ubi_rootfs -s $rootfs_size
  ubiupdatevol /dev/ubi0_0 /tmp/ubi0_0
  ubiupdatevol /dev/ubi0_1 /tmp/ubi0_1

Option 2 - from within OpenWrt
------------------------------

This option requires to flash an initramfs version first so that access
to the flash is possible. This can be achieved by sysupgrading to the
recovery.bin version and rebooting. Once rebooted, you are again in a
default OpenWrt installation, but no partition is mounted.

Follow the commands from Option 1 to flash back to stock.

LTE Modem
=========

The LTE modem is similar to other ZTE devices and controls some more LEDs
and battery management.

Configuring the connection using uqmi works properly, the modem
provides three serial ports and a QMI CDC ethernet interface.

Signed-off-by: Andreas Böhler <dev@aboehler.at>
(cherry picked from commit f70ee53b08)

package/firmware/ipq-wifi/Makefile

@@ -40,6 +40,7 @@ ALLWIFIBOARDS:= \
 	wallys_dr40x9 \
 	xiaomi_ax3600 \
 	xiaomi_ax9000 \
+	zte_mf287plus \
 	zyxel_nbg7815
 
 ALLWIFIPACKAGES:=$(foreach BOARD,$(ALLWIFIBOARDS),ipq-wifi-$(BOARD))
@@ -126,6 +127,7 @@ $(eval $(call generate-ipq-wifi-package,redmi_ax6,Redmi AX6))
 $(eval $(call generate-ipq-wifi-package,wallys_dr40x9,Wallys DR40X9))
 $(eval $(call generate-ipq-wifi-package,xiaomi_ax3600,Xiaomi AX3600))
 $(eval $(call generate-ipq-wifi-package,xiaomi_ax9000,Xiaomi AX9000))
+$(eval $(call generate-ipq-wifi-package,zte_mf287plus,ZTE MF287Plus))
 $(eval $(call generate-ipq-wifi-package,zyxel_nbg7815,Zyxel NBG7815))
 
 $(foreach PACKAGE,$(ALLWIFIPACKAGES),$(eval $(call BuildPackage,$(PACKAGE))))

target/linux/ipq40xx/base-files/etc/board.d/02_network

@@ -107,6 +107,10 @@ ipq40xx_setup_interfaces()
 	zte,mf286d)
 		ucidef_set_interfaces_lan_wan "lan2 lan3 lan4" "wan"
 		;;
+	zte,mf287plus)
+		ucidef_set_interface_lan "lan1 lan2 lan3 lan4"
+		ucidef_set_interface "wan" device "/dev/cdc-wdm0" protocol "qmi"
+		;;
 	*)
 		echo "Unsupported hardware. Network interfaces not initialized"
 		;;

target/linux/ipq40xx/base-files/lib/upgrade/platform.sh

@@ -27,6 +27,7 @@ EOF
 		;;
 	zte,mf18a |\
 	zte,mf286d |\
+	zte,mf287plus |\
 	zte,mf289f)
 		CI_UBIPART="rootfs"
 		local mtdnum="$( find_mtd_index $CI_UBIPART )"
@@ -208,6 +209,7 @@ platform_do_upgrade() {
 	teltonika,rutx10 |\
 	zte,mf18a |\
 	zte,mf286d |\
+	zte,mf287plus |\
 	zte,mf289f)
 		CI_UBIPART="rootfs"
 		nand_do_upgrade "$1"

target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4018-mf287plus.dts

@@ -0,0 +1,384 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+// Copyright (c) 2022, Pawel Dembicki <paweldembicki@gmail.com>.
+// Copyright (c) 2022, Giammarco Marzano <stich86@gmail.com>.
+// Copyright (c) 2023, Andreas Böhler <dev@aboehler.at>
+
+#include "qcom-ipq4019.dtsi"
+#include <dt-bindings/soc/qcom,tcsr.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+
+/ {
+	model = "ZTE MF287Plus";
+	compatible = "zte,mf287plus";
+
+	aliases {
+		led-boot = &led_status;
+		led-failsafe = &led_status;
+		led-running = &led_status;
+		led-upgrade = &led_status;
+	};
+
+	chosen {
+		/*
+		 * bootargs forced by u-boot bootipq command:
+		 * 'ubi.mtd=rootfs root=mtd:ubi_rootfs rootfstype=squashfs rootwait'
+		 */
+		bootargs-append = " root=/dev/ubiblock0_1";
+	};
+
+	/*
+	 * This node is used to restart modem module to avoid anomalous
+	 * behaviours on initial communication.
+	 */
+	gpio-restart {
+		compatible = "gpio-restart";
+		gpios = <&tlmm 5 GPIO_ACTIVE_HIGH>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led_status: led-0 {
+			label = "blue:power";
+			function = LED_FUNCTION_POWER;
+			color = <LED_COLOR_ID_BLUE>;
+			gpios = <&tlmm 0 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	keys {
+		compatible = "gpio-keys";
+
+		key-reset {
+			label = "reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&tlmm 63 GPIO_ACTIVE_LOW>;
+		};
+
+		key-wps {
+			label = "wps";
+			linux,code = <KEY_WPS_BUTTON>;
+			gpios = <&tlmm 2 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	soc {
+		rng@22000 {
+			status = "okay";
+		};
+
+		tcsr@1949000 {
+			compatible = "qcom,tcsr";
+			reg = <0x1949000 0x100>;
+			qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>;
+		};
+
+		tcsr@194b000 {
+			/* select hostmode */
+			compatible = "qcom,tcsr";
+			reg = <0x194b000 0x100>;
+			qcom,usb-hsphy-mode-select = <TCSR_USB_HSPHY_HOST_MODE>;
+			status = "okay";
+		};
+
+		ess_tcsr@1953000 {
+			compatible = "qcom,tcsr";
+			reg = <0x1953000 0x1000>;
+			qcom,ess-interface-select = <TCSR_ESS_PSGMII>;
+		};
+
+		tcsr@1957000 {
+			compatible = "qcom,tcsr";
+			reg = <0x1957000 0x100>;
+			qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>;
+		};
+	};
+};
+
+&mdio {
+	status = "okay";
+};
+
+&watchdog {
+	status = "okay";
+};
+
+&blsp_dma {
+	status = "okay";
+};
+
+&usb2 {
+	status = "okay";
+};
+
+&usb3 {
+	status = "okay";
+};
+
+&blsp1_spi1 {
+	pinctrl-0 = <&spi_0_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+	cs-gpios = <&tlmm 54 GPIO_ACTIVE_HIGH>,
+		   <&tlmm 59 GPIO_ACTIVE_HIGH>,
+		   <&tlmm 1 GPIO_ACTIVE_HIGH>;
+
+	flash@0 {
+		compatible = "jedec,spi-nor";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		reg = <0>;
+		spi-max-frequency = <24000000>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition@0 {
+				label = "0:SBL1";
+				reg = <0x0 0x40000>;
+				read-only;
+			};
+
+			partition@40000 {
+				label = "0:MIBIB";
+				reg = <0x40000 0x20000>;
+				read-only;
+			};
+
+			partition@60000 {
+				label = "0:QSEE";
+				reg = <0x60000 0x60000>;
+				read-only;
+			};
+
+			partition@c0000 {
+				label = "0:CDT";
+				reg = <0xc0000 0x10000>;
+				read-only;
+			};
+
+			partition@d0000 {
+				label = "0:DDRPARAMS";
+				reg = <0xd0000 0x10000>;
+				read-only;
+			};
+
+			partition@e0000 {
+				label = "0:APPSBLENV";
+				reg = <0xe0000 0x10000>;
+				read-only;
+			};
+
+			partition@f0000 {
+				label = "0:APPSBL";
+				reg = <0xf0000 0xc0000>;
+				read-only;
+			};
+
+			partition@1b0000 {
+				label = "0:reserved1";
+				reg = <0x1b0000 0x50000>;
+				read-only;
+			};
+		};
+	};
+
+	spi-nand@1 { /* flash@1 ? */
+		compatible = "spi-nand";
+		reg = <1>;
+		spi-max-frequency = <24000000>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition@0 {
+				label = "fota-flag";
+				reg = <0x0 0x140000>;
+				read-only;
+			};
+
+			partition@140000 {
+				label = "ART";
+				reg = <0x140000 0x140000>;
+				read-only;
+				compatible = "nvmem-cells";
+				#address-cells = <1>;
+				#size-cells = <1>;
+
+				precal_art_1000: precal@1000 {
+					reg = <0x1000 0x2f20>;
+				};
+
+				precal_art_5000: precal@5000 {
+					reg = <0x5000 0x2f20>;
+				};
+			};
+
+			partition@280000 {
+				label = "mac";
+				reg = <0x280000 0x140000>;
+				read-only;
+				compatible = "nvmem-cells";
+				#address-cells = <1>;
+				#size-cells = <1>;
+
+				macaddr_mac_0: macaddr@0 {
+					reg = <0x0 0x6>;
+				};
+			};
+
+			partition@3c0000 {
+				label = "cfg-param";
+				reg = <0x3c0000 0x600000>;
+				read-only;
+			};
+
+			partition@9c0000 {
+				label = "oops";
+				reg = <0x9c0000 0x140000>;
+			};
+
+			partition@b00000 {
+				label = "web";
+				reg = <0xb00000 0x800000>;
+			};
+
+			partition@1300000 {
+				label = "rootfs";
+				reg = <0x1300000 0x2200000>;
+			};
+
+			partition@3500000 {
+				label = "data";
+				reg = <0x3500000 0x1900000>;
+			};
+
+			partition@4e00000 {
+				label = "fota";
+				reg = <0x4e00000 0x3200000>;
+			};
+		};
+	};
+
+	zigbee@2 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		compatible = "silabs,em3581";
+		reg = <2>;
+		spi-max-frequency = <12000000>;
+	};
+};
+
+&blsp1_uart1 {
+	pinctrl-0 = <&serial_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&crypto {
+	status = "okay";
+};
+
+&cryptobam {
+	status = "okay";
+};
+
+&gmac {
+	status = "okay";
+	nvmem-cell-names = "mac-address";
+	nvmem-cells = <&macaddr_mac_0>;
+	mac-address-increment = <2>;
+};
+
+&switch {
+	status = "okay";
+};
+
+&swport2 {
+	status = "okay";
+
+	label = "lan1";
+};
+
+&swport3 {
+	status = "okay";
+
+	label = "lan2";
+};
+
+&swport4 {
+	status = "okay";
+
+	label = "lan3";
+};
+
+&swport5 {
+	status = "okay";
+
+	label = "lan4";
+};
+
+&qpic_bam {
+	status = "okay";
+};
+
+&tlmm {
+	serial_pins: serial_pinmux {
+		mux {
+			pins = "gpio60", "gpio61";
+			function = "blsp_uart0";
+			bias-disable;
+		};
+	};
+
+	spi_0_pins: spi_0_pinmux {
+		pinmux {
+			function = "blsp_spi0";
+			pins = "gpio55", "gpio56", "gpio57";
+			drive-strength = <12>;
+			bias-disable;
+		};
+
+		pinmux_cs {
+			function = "gpio";
+			pins = "gpio54", "gpio59", "gpio1";
+			drive-strength = <2>;
+			bias-disable;
+			output-high;
+		};
+	};
+};
+
+&usb2_hs_phy {
+	status = "okay";
+};
+
+&usb3_ss_phy {
+	status = "okay";
+};
+
+&usb3_hs_phy {
+	status = "okay";
+};
+
+&wifi0 {
+	status = "okay";
+	nvmem-cell-names = "pre-calibration", "mac-address";
+	nvmem-cells = <&precal_art_1000>, <&macaddr_mac_0>;
+	qcom,ath10k-calibration-variant = "zte,mf287plus";
+};
+
+&wifi1 {
+	status = "okay";
+	nvmem-cell-names = "pre-calibration", "mac-address";
+	nvmem-cells = <&precal_art_5000>, <&macaddr_mac_0>;
+	mac-address-increment = <1>;
+	qcom,ath10k-calibration-variant = "zte,mf287plus";
+};

target/linux/ipq40xx/image/generic.mk

@@ -1148,6 +1148,24 @@ define Device/zte_mf286d
 endef
 TARGET_DEVICES += zte_mf286d
 
+define Device/zte_mf287plus
+	$(call Device/zte_mf28x_common)
+	DEVICE_DTS_CONFIG := config@ap.dk01.1-c2
+	DEVICE_MODEL := MF287Plus
+	DEVICE_ALT0_VENDOR := ZTE
+	DEVICE_ALT0_MODEL := MF287
+	DEVICE_PACKAGES += ipq-wifi-zte_mf287plus
+	SOC := qcom-ipq4018
+#	The recovery image is used to return back to stock (an initramfs-based image
+#	that can be flashed to the device via sysupgrade
+#	The factory image is used to install from the stock firmware by using an
+#	exploit for the web interface
+	IMAGES += factory.bin recovery.bin
+	IMAGE/factory.bin  := append-ubi
+	IMAGE/recovery.bin := append-squashfs4-fakeroot | sysupgrade-tar kernel=$$$$(BIN_DIR)/openwrt-$$(BOARD)$$(if $$(SUBTARGET),-$$(SUBTARGET))-$$(DEVICE_NAME)-initramfs-zImage.itb rootfs=$$$$@ | append-metadata
+endef
+TARGET_DEVICES += zte_mf287plus
+
 define Device/zte_mf289f
 	$(call Device/zte_mf28x_common)
 	DEVICE_MODEL := MF289F