openwrt/package/boot/uboot-envtools/files/realtek

49 lines
1.2 KiB
Plaintext
Raw Normal View History

[ -e /etc/config/ubootenv ] && exit 0
touch /etc/config/ubootenv
. /lib/uboot-envtools.sh
. /lib/functions.sh
board=$(board_name)
case "$board" in
d-link,dgs-1210-16|\
d-link,dgs-1210-28|\
d-link,dgs-1210-10p|\
realtek: Add ZyXEL GS1900-8 The ZyXEL GS1900-8 is a 8 port switch without any PoE functionality or SFP ports, but otherwise similar to the other GS1900 switches. Specifications -------------- * Device: ZyXEL GS1900-8 v1.2 * SoC: Realtek RTL8380M 500 MHz MIPS 4KEc * Flash: Macronix MX25L12835F 16 MiB * RAM: Nanya NT5TU128M8GE-AC 128 MiB DDR2 SDRAM * Ethernet: 8x 10/100/1000 Mbit * LEDs: 1 PWR LED (green, not configurable) 1 SYS LED (green, configurable) 8 ethernet port status LEDs (green, SoC controlled) * Buttons: 1 on-off glide switch at the back (not configurable) 1 reset button at the right side, behind the air-vent (not configurable) 1 reset button on front panel (configurable) * Power 12V 1A barrel connector * UART: 1 serial header (JP2) with populated standard pin connector on the left side of the PCB, towards the back. Pins are labelled: + VCC (3.3V) + TX (really RX) + RX (really TX) + GND the labelling is done from the usb2serial connector's point of view, so RX/ TX are mixed up. Serial connection parameters for both devices: 115200 8N1. Installation ------------ Instructions are identical to those for the GS1900-10HP and GS1900-8HP. * Configure your client with a static 192.168.1.x IP (e.g. 192.168.1.10). * Set up a TFTP server on your client and make it serve the initramfs image. * Connect serial, power up the switch, interrupt U-boot by hitting the space bar, and enable the network: > rtk network on * Since the GS1900-10HP is a dual-partition device, you want to keep the OEM firmware on the backup partition for the time being. OpenWrt can only boot off the first partition anyway (hardcoded in the DTS). To make sure we are manipulating the first partition, issue the following commands: > setsys bootpartition 0 > savesys * Download the image onto the device and boot from it: > tftpboot 0x84f00000 192.168.1.10:openwrt-realtek-generic-zyxel_gs1900-8-initramfs-kernel.bin > bootm * Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it: > sysupgrade /tmp/openwrt-realtek-generic-zyxel_gs1900-8-squashfs-sysupgrade.bin Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2021-01-27 21:16:11 +00:00
zyxel,gs1900-8|\
zyxel,gs1900-8hp-v1|\
zyxel,gs1900-8hp-v2|\
realtek: add ZyXEL GS1900-24HPv2 support The ZyXEL GS1900-24HPv2 is a 24 port PoE switch with two SFP ports, similar to the other GS1900 switches. Specifications -------------- * Device: ZyXEL GS1900-24HPv2 * SoC: Realtek RTL8382M 500 MHz MIPS 4KEc * Flash: 16 MiB * RAM: W631GG8MB-12 128 MiB DDR3 SDRAM (stock firmware is configured to use only 64 MiB) * Ethernet: 24x 10/100/1000 Mbps, 2x SFP 100/1000 Mbps * LEDs: 1 PWR LED (green, not configurable) 1 SYS LED (green, configurable) 24 ethernet port link/activity LEDs (green, SoC controlled) 24 ethernet port PoE status LEDs 2 SFP status/activity LEDs (green, SoC controlled) * Buttons: 1 "RESTORE" button on front panel 1 "RESET" button on front panel * Power 120-240V AC C13 * UART: 1 serial header (J41) with populated standard pin connector on the left edge of the PCB, angled towards the side. The casing has a rectangular cutout on the side that provides external access to these pins. Pinout (front to back): + GND + TX + RX + VCC Serial connection parameters for both devices: 115200 8N1. Installation ------------ OEM upgrade method: (Possible on master once https://patchwork.ozlabs.org/project/openwrt/patch/20210624210408.19248-1-bjorn@mork.no/ is merged) * Log in to OEM management web interface * Navigate to Maintenance > Firmware > Management * If "Active Image" has the first option selected, OpenWrt will need to be flashed to the "Active" partition. If the second option is selected, OpenWrt will need to be flashed to the "Backup" partition. * Navigate to Maintenance > Firmware > Upload * Upload the openwrt-realtek-generic-zyxel_gs1900-24hp-v2-initramfs-kernel.bin file by your preferred method to the previously determined partition. When prompted, select to boot from the newly flashed image, and reboot the switch. * Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it: > sysupgrade -n /tmp/openwrt-realtek-generic-zyxel_gs1900-24hp-v2-squashfs-sysupgrade.bin it may be necessary to restart the network (/etc/init.d/network restart) on the running initramfs image. U-Boot TFTP method: * Configure your client with a static 192.168.1.x IP (e.g. 192.168.1.10). * Set up a TFTP server on your client and make it serve the initramfs image. * Connect serial, power up the switch, interrupt U-boot by hitting the space bar, and enable the network: > rtk network on * Since the GS1900-24HPv2 is a dual-partition device, you want to keep the OEM firmware on the backup partition for the time being. OpenWrt can only boot from the first partition anyway (hardcoded in the DTS). To make sure we are manipulating the first partition, issue the following commands: > setsys bootpartition 0 > savesys * Download the image onto the device and boot from it: > tftpboot 0x84f00000 192.168.1.10:openwrt-realtek-generic-zyxel_gs1900-24hp-v2-initramfs-kernel.bin > bootm * Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it: > sysupgrade -n /tmp/openwrt-realtek-generic-zyxel_gs1900-24hp-v2-squashfs-sysupgrade.bin it may be necessary to restart the network (/etc/init.d/network restart) on the running initramfs image. Signed-off-by: Soma Zambelly <zambelly.soma@gmail.com>
2021-08-24 21:46:08 +00:00
zyxel,gs1900-10hp|\
realtek: add ZyXEL GS1900-24 v1 support The ZyXEL GS1900-24 v1 is a 24 port switch with two SFP ports, similar to the other GS1900 switches. Specifications -------------- * Device: ZyXEL GS1900-24 v1 * SoC: Realtek RTL8382M 500 MHz MIPS 4KEc * Flash: 16 MiB * RAM: Winbond W9751G8KB-25 64 MiB DDR2 SDRAM * Ethernet: 24x 10/100/1000 Mbps, 2x SFP 100/1000 Mbps * LEDs: * 1 PWR LED (green, not configurable) * 1 SYS LED (green, configurable) * 24 ethernet port link/activity LEDs (green, SoC controlled) * 2 SFP status/activity LEDs (green, SoC controlled) * Buttons: * 1 "RESET" button on front panel (soft reset) * 1 button ('SW1') behind right hex grate (hardwired power-off) * Power: 120-240V AC C13 * UART: Internal populated 10-pin header ('J5') providing RS232; connected to SoC UART through a SIPEX 3232EC for voltage level shifting. * 'J5' RS232 Pinout (dot as pin 1): 2) SoC RXD 3) GND 10) SoC TXD Serial connection parameters: 115200 8N1. Installation ------------ OEM upgrade method: * Log in to OEM management web interface * Navigate to Maintenance > Firmware > Management * If "Active Image" has the first option selected, OpenWrt will need to be flashed to the "Active" partition. If the second option is selected, OpenWrt will need to be flashed to the "Backup" partition. * Navigate to Maintenance > Firmware > Upload * Upload the openwrt-realtek-rtl838x-zyxel_gs1900-24-v1-initramfs-kernel.bin file by your preferred method to the previously determined partition. When prompted, select to boot from the newly flashed image, and reboot the switch. * Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it: > sysupgrade /tmp/openwrt-realtek-rtl838x-zyxel_gs1900-24-v1-squashfs-sysupgrade.bin U-Boot TFTP method: * Configure your client with a static 192.168.1.x IP (e.g. 192.168.1.10). * Set up a TFTP server on your client and make it serve the initramfs image. * Connect serial, power up the switch, interrupt U-boot by hitting the space bar, and enable the network: > rtk network on > Since the GS1900-24 v1 is a dual-partition device, you want to keep the OEM firmware on the backup partition for the time being. OpenWrt can only be installed in the first partition anyway (hardcoded in the DTS). To ensure we are set to boot from the first partition, issue the following commands: > setsys bootpartition 0 > savesys * Download the image onto the device and boot from it: > tftpboot 0x81f00000 192.168.1.10:openwrt-realtek-rtl838x-zyxel_gs1900-24-v1-initramfs-kernel.bin > bootm * Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it: > sysupgrade /tmp/openwrt-realtek-rtl838x-zyxel_gs1900-24-v1-squashfs-sysupgrade.bin Signed-off-by: Martin Kennedy <hurricos@gmail.com>
2022-03-05 19:02:36 +00:00
zyxel,gs1900-24-v1|\
realtek: add ZyXEL GS1900-24HPv2 support The ZyXEL GS1900-24HPv2 is a 24 port PoE switch with two SFP ports, similar to the other GS1900 switches. Specifications -------------- * Device: ZyXEL GS1900-24HPv2 * SoC: Realtek RTL8382M 500 MHz MIPS 4KEc * Flash: 16 MiB * RAM: W631GG8MB-12 128 MiB DDR3 SDRAM (stock firmware is configured to use only 64 MiB) * Ethernet: 24x 10/100/1000 Mbps, 2x SFP 100/1000 Mbps * LEDs: 1 PWR LED (green, not configurable) 1 SYS LED (green, configurable) 24 ethernet port link/activity LEDs (green, SoC controlled) 24 ethernet port PoE status LEDs 2 SFP status/activity LEDs (green, SoC controlled) * Buttons: 1 "RESTORE" button on front panel 1 "RESET" button on front panel * Power 120-240V AC C13 * UART: 1 serial header (J41) with populated standard pin connector on the left edge of the PCB, angled towards the side. The casing has a rectangular cutout on the side that provides external access to these pins. Pinout (front to back): + GND + TX + RX + VCC Serial connection parameters for both devices: 115200 8N1. Installation ------------ OEM upgrade method: (Possible on master once https://patchwork.ozlabs.org/project/openwrt/patch/20210624210408.19248-1-bjorn@mork.no/ is merged) * Log in to OEM management web interface * Navigate to Maintenance > Firmware > Management * If "Active Image" has the first option selected, OpenWrt will need to be flashed to the "Active" partition. If the second option is selected, OpenWrt will need to be flashed to the "Backup" partition. * Navigate to Maintenance > Firmware > Upload * Upload the openwrt-realtek-generic-zyxel_gs1900-24hp-v2-initramfs-kernel.bin file by your preferred method to the previously determined partition. When prompted, select to boot from the newly flashed image, and reboot the switch. * Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it: > sysupgrade -n /tmp/openwrt-realtek-generic-zyxel_gs1900-24hp-v2-squashfs-sysupgrade.bin it may be necessary to restart the network (/etc/init.d/network restart) on the running initramfs image. U-Boot TFTP method: * Configure your client with a static 192.168.1.x IP (e.g. 192.168.1.10). * Set up a TFTP server on your client and make it serve the initramfs image. * Connect serial, power up the switch, interrupt U-boot by hitting the space bar, and enable the network: > rtk network on * Since the GS1900-24HPv2 is a dual-partition device, you want to keep the OEM firmware on the backup partition for the time being. OpenWrt can only boot from the first partition anyway (hardcoded in the DTS). To make sure we are manipulating the first partition, issue the following commands: > setsys bootpartition 0 > savesys * Download the image onto the device and boot from it: > tftpboot 0x84f00000 192.168.1.10:openwrt-realtek-generic-zyxel_gs1900-24hp-v2-initramfs-kernel.bin > bootm * Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it: > sysupgrade -n /tmp/openwrt-realtek-generic-zyxel_gs1900-24hp-v2-squashfs-sysupgrade.bin it may be necessary to restart the network (/etc/init.d/network restart) on the running initramfs image. Signed-off-by: Soma Zambelly <zambelly.soma@gmail.com>
2021-08-24 21:46:08 +00:00
zyxel,gs1900-24hp-v2)
idx="$(find_mtd_index u-boot-env)"
[ -n "$idx" ] && \
ubootenv_add_uci_config "/dev/mtd$idx" "0x0" "0x400" "0x10000"
idx2="$(find_mtd_index u-boot-env2)"
[ -n "$idx2" ] && \
ubootenv_add_uci_sys_config "/dev/mtd$idx2" "0x0" "0x1000" "0x10000"
;;
iodata,bsh-g24mb)
idx="$(find_mtd_index u-boot-env)"
[ -n "$idx" ] && \
ubootenv_add_uci_config "/dev/mtd$idx" "0x0" "0x10000" "0x10000"
idx2="$(find_mtd_index u-boot-env2)"
[ -n "$idx2" ] && \
ubootenv_add_uci_sys_config "/dev/mtd$idx2" "0x0" "0x3800" "0x10000"
;;
*)
idx="$(find_mtd_index u-boot-env)"
[ -n "$idx" ] && \
ubootenv_add_uci_config "/dev/mtd$idx" "0x0" "0x10000" "0x10000"
idx2="$(find_mtd_index u-boot-env2)"
[ -n "$idx2" ] && \
ubootenv_add_uci_sys_config "/dev/mtd$idx2" "0x0" "0x1000" "0x10000"
;;
esac
config_load ubootenv
config_foreach ubootenv_add_app_config
exit 0