openwrt/target/linux/rtl838x/patches-5.4/300-mips-add-rtl838x-platform.patch

43 lines
1.0 KiB
Diff
Raw Normal View History

rtl838x: add new architecture This adds support for the RTL838x Architecture. SoCs of this type are used in managed and un-managed Switches and Routers with 8-28 ports. Drivers are provided for SoC initialization, GPIOs, Flash, Ethernet including a DSA switch driver and internal and external PHYs used with these switches. Supported SoCs: RTL8380M RTL8381M RTL8382M The kernel will also boot on the following RTL839x SoCs, however driver support apart from spi-nor is missing: RTL8390 RTL8391 RTL8393 The following PHYs are supported: RTL8214FC (Quad QSGMII multiplexing GMAC and SFP port) RTL8218B internal: internal PHY of the RTL838x chips RTL8318b external (QSGMII 8-port GMAC phy) RTL8382M SerDes for 2 SFP ports Initialization sequences for the PHYs are provided in the form of firmware files. Flash driver supports 3 / 4 byte access DSA switch driver supports VLANs, port isolation, STP and port mirroring. The ALLNET ALL-SG8208M is supported as Proof of Concept: RTL8382M SoC 1 MIPS 4KEc core @ 500MHz 8 Internal PHYs (RTL8218B) 128MB DRAM (Nanya NT5TU128MB) 16MB NOR Flash (MXIC 25L128) 8 GBEthernet ports with one green status LED each (SoC controlled) 1 Power LED (not configurable) 1 SYS LED (configurable) 1 On-Off switch (not configurable) 1 Reset button at the right behind right air-vent (not configurable) 1 Reset button on front panel (configurable) 12V 1A barrel connector 1 serial header with populated standard pin connector and with markings GND TX RX Vcc(3.3V), connection properties: 115200 8N1 To install, upload the sysupgrade image to the OEM webpage. Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2020-09-13 07:06:13 +00:00
--- a/arch/mips/Kbuild.platforms
+++ b/arch/mips/Kbuild.platforms
@@ -27,6 +27,7 @@ platforms += pistachio
platforms += pmcs-msp71xx
platforms += pnx833x
platforms += ralink
+platforms += rtl838x
platforms += rb532
platforms += sgi-ip22
platforms += sgi-ip27
--- a/arch/mips/Kconfig
+++ b/arch/mips/Kconfig
@@ -630,6 +630,29 @@ config RALINK
rtl838x: add new architecture This adds support for the RTL838x Architecture. SoCs of this type are used in managed and un-managed Switches and Routers with 8-28 ports. Drivers are provided for SoC initialization, GPIOs, Flash, Ethernet including a DSA switch driver and internal and external PHYs used with these switches. Supported SoCs: RTL8380M RTL8381M RTL8382M The kernel will also boot on the following RTL839x SoCs, however driver support apart from spi-nor is missing: RTL8390 RTL8391 RTL8393 The following PHYs are supported: RTL8214FC (Quad QSGMII multiplexing GMAC and SFP port) RTL8218B internal: internal PHY of the RTL838x chips RTL8318b external (QSGMII 8-port GMAC phy) RTL8382M SerDes for 2 SFP ports Initialization sequences for the PHYs are provided in the form of firmware files. Flash driver supports 3 / 4 byte access DSA switch driver supports VLANs, port isolation, STP and port mirroring. The ALLNET ALL-SG8208M is supported as Proof of Concept: RTL8382M SoC 1 MIPS 4KEc core @ 500MHz 8 Internal PHYs (RTL8218B) 128MB DRAM (Nanya NT5TU128MB) 16MB NOR Flash (MXIC 25L128) 8 GBEthernet ports with one green status LED each (SoC controlled) 1 Power LED (not configurable) 1 SYS LED (configurable) 1 On-Off switch (not configurable) 1 Reset button at the right behind right air-vent (not configurable) 1 Reset button on front panel (configurable) 12V 1A barrel connector 1 serial header with populated standard pin connector and with markings GND TX RX Vcc(3.3V), connection properties: 115200 8N1 To install, upload the sysupgrade image to the OEM webpage. Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2020-09-13 07:06:13 +00:00
select ARCH_HAS_RESET_CONTROLLER
select RESET_CONTROLLER
+config RTL838X
+ bool "Realtek based platforms"
+ select DMA_NONCOHERENT
+ select IRQ_MIPS_CPU
+ select CSRC_R4K
+ select CEVT_R4K
+ select SYS_HAS_CPU_MIPS32_R1
+ select SYS_HAS_CPU_MIPS32_R2
+ select SYS_SUPPORTS_BIG_ENDIAN
+ select SYS_SUPPORTS_32BIT_KERNEL
+ select SYS_SUPPORTS_MIPS16
+ select SYS_SUPPORTS_MULTITHREADING
+ select SYS_SUPPORTS_VPE_LOADER
+ select SYS_HAS_EARLY_PRINTK
+ select SWAP_IO_SPACE
+ select BOOT_RAW
+ select CLKDEV_LOOKUP
+ select PINCTRL
+ select ARCH_HAS_RESET_CONTROLLER
+ select RESET_CONTROLLER
+ select RTL8380_SERIES
+ select USE_OF
+
config SGI_IP22
bool "SGI IP22 (Indy/Indigo2)"
select FW_ARC