openwrt/target/linux/ramips/dts/mt7621_beeline_smartbox-giga.dts

250 lines
4.4 KiB
Plaintext
Raw Normal View History

ramips: add support for Beeline SmartBox GIGA Beeline SmartBox GIGA is a wireless WiFi 5 router manufactured by Sercomm company. Device specification -------------------- SoC Type: MediaTek MT7621AT RAM: 256 MiB, Nanya NT5CC128M16JR-EK Flash: 128 MiB, Macronix MX30LF1G18AC Wireless 2.4 GHz (MT7603EN): b/g/n, 2x2 Wireless 5 GHz (MT7613BE): a/n/ac, 2x2 Ethernet: 3 ports - 2xGbE (WAN, LAN1), 1xFE (LAN2) USB ports: 1xUSB3.0 Button: 1 button (Reset/WPS) PCB ID: DBE00B-1.6MM LEDs: 1 RGB LED Power: 12 VDC, 1.5 A Connector type: barrel Bootloader: U-Boot Installation ----------------- 1. Downgrade stock (Beeline) firmware to v.1.0.02; 2. Give factory OpenWrt image a shorter name, e.g. 1001.img; 3. Upload and update the firmware via the original web interface. Remark: You might need make the 3rd step twice if your running firmware is booted from the Slot 1 (Sercomm0 bootflag). The stock firmware reverses the bootflag (Sercomm0 / Sercomm1) on each firmware update. Revert to stock --------------- 1. Change the bootflag to Sercomm1 in OpenWrt CLI and then reboot: printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3 2. Optional: Update with any stock (Beeline) firmware if you want to overwrite OpenWrt in Slot 0 completely. MAC Addresses ------------- +-----+-----------+---------+ | use | address | example | +-----+-----------+---------+ | LAN | label | *:16 | | WAN | label + 1 | *:17 | | 2g | label + 4 | *:1a | | 5g | label + 5 | *:1b | +-----+-----------+---------+ The label MAC address was found in Factory 0x21000 Notes ----- 1. The following scripts are required for the build: sercomm-crypto.py - already exists in OpenWrt sercomm-partition-tag.py - already exists in OpenWrt sercomm-payload.py - already exists in OpenWrt sercomm-pid.py - new, the part of this pull request sercomm-kernel-header.py - new, the part of this pull request 2. This device (same as other Sercomm S2,S3-based devices) requires special LZMA and LOADADDR settings for successful boot: LZMA_TEXT_START=0x82800000 KERNEL_LOADADDR=0x81001000 LOADADDR=0x80001000 3. This device (same as several other Sercomm-based devices - Beeline, Netgear, Etisalat, Rostelecom) has partition map (mtd1) containing real partition offsets, which may differ from device to device depending on the number and location of bad blocks on NAND. "fixed-partitions" is used if the partition map is not found or corrupted. This behavour (it's the same as on stock firmware) is provided by MTD_SERCOMM_PARTS module. Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
2022-03-18 18:09:45 +00:00
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
#include "mt7621.dtsi"
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
#include <dt-bindings/leds/common.h>
/ {
compatible = "beeline,smartbox-giga", "mediatek,mt7621-soc";
model = "Beeline SmartBox GIGA";
aliases {
label-mac-device = &gmac0;
led-boot = &led_status_green;
led-failsafe = &led_status_red;
led-running = &led_status_green;
led-upgrade = &led_status_red;
};
leds {
compatible = "gpio-leds";
led_status_green: led-0 {
label = "green:status";
color = <LED_COLOR_ID_GREEN>;
function = LED_FUNCTION_STATUS;
gpios = <&gpio 13 GPIO_ACTIVE_HIGH>;
};
led-1 {
label = "blue:wan";
color = <LED_COLOR_ID_BLUE>;
function = LED_FUNCTION_WAN;
gpios = <&gpio 14 GPIO_ACTIVE_HIGH>;
};
led_status_red: led-2 {
label = "red:status";
color = <LED_COLOR_ID_RED>;
function = LED_FUNCTION_STATUS;
gpios = <&gpio 15 GPIO_ACTIVE_HIGH>;
};
};
keys {
compatible = "gpio-keys";
reset {
label = "reset";
gpios = <&gpio 4 GPIO_ACTIVE_LOW>;
linux,code = <KEY_RESTART>;
};
};
ubi-concat {
compatible = "mtd-concat";
devices = <&ubiconcat0 &ubiconcat1 &ubiconcat2 \
&ubiconcat3>;
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
partition@0 {
label = "ubi";
reg = <0x0 0x5400000>;
};
};
};
};
&nand {
status = "okay";
partitions {
compatible = "sercomm,sc-partitions", "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
partition@0 {
label = "u-boot";
reg = <0x0 0x100000>;
sercomm,scpart-id = <0>;
read-only;
};
partition@100000 {
label = "dynamic partition map";
reg = <0x100000 0x100000>;
sercomm,scpart-id = <1>;
};
factory: partition@200000 {
compatible = "nvmem-cells";
ramips: add support for Beeline SmartBox GIGA Beeline SmartBox GIGA is a wireless WiFi 5 router manufactured by Sercomm company. Device specification -------------------- SoC Type: MediaTek MT7621AT RAM: 256 MiB, Nanya NT5CC128M16JR-EK Flash: 128 MiB, Macronix MX30LF1G18AC Wireless 2.4 GHz (MT7603EN): b/g/n, 2x2 Wireless 5 GHz (MT7613BE): a/n/ac, 2x2 Ethernet: 3 ports - 2xGbE (WAN, LAN1), 1xFE (LAN2) USB ports: 1xUSB3.0 Button: 1 button (Reset/WPS) PCB ID: DBE00B-1.6MM LEDs: 1 RGB LED Power: 12 VDC, 1.5 A Connector type: barrel Bootloader: U-Boot Installation ----------------- 1. Downgrade stock (Beeline) firmware to v.1.0.02; 2. Give factory OpenWrt image a shorter name, e.g. 1001.img; 3. Upload and update the firmware via the original web interface. Remark: You might need make the 3rd step twice if your running firmware is booted from the Slot 1 (Sercomm0 bootflag). The stock firmware reverses the bootflag (Sercomm0 / Sercomm1) on each firmware update. Revert to stock --------------- 1. Change the bootflag to Sercomm1 in OpenWrt CLI and then reboot: printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3 2. Optional: Update with any stock (Beeline) firmware if you want to overwrite OpenWrt in Slot 0 completely. MAC Addresses ------------- +-----+-----------+---------+ | use | address | example | +-----+-----------+---------+ | LAN | label | *:16 | | WAN | label + 1 | *:17 | | 2g | label + 4 | *:1a | | 5g | label + 5 | *:1b | +-----+-----------+---------+ The label MAC address was found in Factory 0x21000 Notes ----- 1. The following scripts are required for the build: sercomm-crypto.py - already exists in OpenWrt sercomm-partition-tag.py - already exists in OpenWrt sercomm-payload.py - already exists in OpenWrt sercomm-pid.py - new, the part of this pull request sercomm-kernel-header.py - new, the part of this pull request 2. This device (same as other Sercomm S2,S3-based devices) requires special LZMA and LOADADDR settings for successful boot: LZMA_TEXT_START=0x82800000 KERNEL_LOADADDR=0x81001000 LOADADDR=0x80001000 3. This device (same as several other Sercomm-based devices - Beeline, Netgear, Etisalat, Rostelecom) has partition map (mtd1) containing real partition offsets, which may differ from device to device depending on the number and location of bad blocks on NAND. "fixed-partitions" is used if the partition map is not found or corrupted. This behavour (it's the same as on stock firmware) is provided by MTD_SERCOMM_PARTS module. Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
2022-03-18 18:09:45 +00:00
label = "Factory";
reg = <0x200000 0x100000>;
#address-cells = <1>;
#size-cells = <1>;
ramips: add support for Beeline SmartBox GIGA Beeline SmartBox GIGA is a wireless WiFi 5 router manufactured by Sercomm company. Device specification -------------------- SoC Type: MediaTek MT7621AT RAM: 256 MiB, Nanya NT5CC128M16JR-EK Flash: 128 MiB, Macronix MX30LF1G18AC Wireless 2.4 GHz (MT7603EN): b/g/n, 2x2 Wireless 5 GHz (MT7613BE): a/n/ac, 2x2 Ethernet: 3 ports - 2xGbE (WAN, LAN1), 1xFE (LAN2) USB ports: 1xUSB3.0 Button: 1 button (Reset/WPS) PCB ID: DBE00B-1.6MM LEDs: 1 RGB LED Power: 12 VDC, 1.5 A Connector type: barrel Bootloader: U-Boot Installation ----------------- 1. Downgrade stock (Beeline) firmware to v.1.0.02; 2. Give factory OpenWrt image a shorter name, e.g. 1001.img; 3. Upload and update the firmware via the original web interface. Remark: You might need make the 3rd step twice if your running firmware is booted from the Slot 1 (Sercomm0 bootflag). The stock firmware reverses the bootflag (Sercomm0 / Sercomm1) on each firmware update. Revert to stock --------------- 1. Change the bootflag to Sercomm1 in OpenWrt CLI and then reboot: printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3 2. Optional: Update with any stock (Beeline) firmware if you want to overwrite OpenWrt in Slot 0 completely. MAC Addresses ------------- +-----+-----------+---------+ | use | address | example | +-----+-----------+---------+ | LAN | label | *:16 | | WAN | label + 1 | *:17 | | 2g | label + 4 | *:1a | | 5g | label + 5 | *:1b | +-----+-----------+---------+ The label MAC address was found in Factory 0x21000 Notes ----- 1. The following scripts are required for the build: sercomm-crypto.py - already exists in OpenWrt sercomm-partition-tag.py - already exists in OpenWrt sercomm-payload.py - already exists in OpenWrt sercomm-pid.py - new, the part of this pull request sercomm-kernel-header.py - new, the part of this pull request 2. This device (same as other Sercomm S2,S3-based devices) requires special LZMA and LOADADDR settings for successful boot: LZMA_TEXT_START=0x82800000 KERNEL_LOADADDR=0x81001000 LOADADDR=0x80001000 3. This device (same as several other Sercomm-based devices - Beeline, Netgear, Etisalat, Rostelecom) has partition map (mtd1) containing real partition offsets, which may differ from device to device depending on the number and location of bad blocks on NAND. "fixed-partitions" is used if the partition map is not found or corrupted. This behavour (it's the same as on stock firmware) is provided by MTD_SERCOMM_PARTS module. Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
2022-03-18 18:09:45 +00:00
sercomm,scpart-id = <2>;
read-only;
eeprom_factory_0: eeprom@0 {
reg = <0x0 0x400>;
};
ramips: add support for Beeline SmartBox GIGA Beeline SmartBox GIGA is a wireless WiFi 5 router manufactured by Sercomm company. Device specification -------------------- SoC Type: MediaTek MT7621AT RAM: 256 MiB, Nanya NT5CC128M16JR-EK Flash: 128 MiB, Macronix MX30LF1G18AC Wireless 2.4 GHz (MT7603EN): b/g/n, 2x2 Wireless 5 GHz (MT7613BE): a/n/ac, 2x2 Ethernet: 3 ports - 2xGbE (WAN, LAN1), 1xFE (LAN2) USB ports: 1xUSB3.0 Button: 1 button (Reset/WPS) PCB ID: DBE00B-1.6MM LEDs: 1 RGB LED Power: 12 VDC, 1.5 A Connector type: barrel Bootloader: U-Boot Installation ----------------- 1. Downgrade stock (Beeline) firmware to v.1.0.02; 2. Give factory OpenWrt image a shorter name, e.g. 1001.img; 3. Upload and update the firmware via the original web interface. Remark: You might need make the 3rd step twice if your running firmware is booted from the Slot 1 (Sercomm0 bootflag). The stock firmware reverses the bootflag (Sercomm0 / Sercomm1) on each firmware update. Revert to stock --------------- 1. Change the bootflag to Sercomm1 in OpenWrt CLI and then reboot: printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3 2. Optional: Update with any stock (Beeline) firmware if you want to overwrite OpenWrt in Slot 0 completely. MAC Addresses ------------- +-----+-----------+---------+ | use | address | example | +-----+-----------+---------+ | LAN | label | *:16 | | WAN | label + 1 | *:17 | | 2g | label + 4 | *:1a | | 5g | label + 5 | *:1b | +-----+-----------+---------+ The label MAC address was found in Factory 0x21000 Notes ----- 1. The following scripts are required for the build: sercomm-crypto.py - already exists in OpenWrt sercomm-partition-tag.py - already exists in OpenWrt sercomm-payload.py - already exists in OpenWrt sercomm-pid.py - new, the part of this pull request sercomm-kernel-header.py - new, the part of this pull request 2. This device (same as other Sercomm S2,S3-based devices) requires special LZMA and LOADADDR settings for successful boot: LZMA_TEXT_START=0x82800000 KERNEL_LOADADDR=0x81001000 LOADADDR=0x80001000 3. This device (same as several other Sercomm-based devices - Beeline, Netgear, Etisalat, Rostelecom) has partition map (mtd1) containing real partition offsets, which may differ from device to device depending on the number and location of bad blocks on NAND. "fixed-partitions" is used if the partition map is not found or corrupted. This behavour (it's the same as on stock firmware) is provided by MTD_SERCOMM_PARTS module. Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
2022-03-18 18:09:45 +00:00
eeprom_factory_8000: eeprom@8000 {
reg = <0x8000 0x4da8>;
};
ramips: add support for Beeline SmartBox GIGA Beeline SmartBox GIGA is a wireless WiFi 5 router manufactured by Sercomm company. Device specification -------------------- SoC Type: MediaTek MT7621AT RAM: 256 MiB, Nanya NT5CC128M16JR-EK Flash: 128 MiB, Macronix MX30LF1G18AC Wireless 2.4 GHz (MT7603EN): b/g/n, 2x2 Wireless 5 GHz (MT7613BE): a/n/ac, 2x2 Ethernet: 3 ports - 2xGbE (WAN, LAN1), 1xFE (LAN2) USB ports: 1xUSB3.0 Button: 1 button (Reset/WPS) PCB ID: DBE00B-1.6MM LEDs: 1 RGB LED Power: 12 VDC, 1.5 A Connector type: barrel Bootloader: U-Boot Installation ----------------- 1. Downgrade stock (Beeline) firmware to v.1.0.02; 2. Give factory OpenWrt image a shorter name, e.g. 1001.img; 3. Upload and update the firmware via the original web interface. Remark: You might need make the 3rd step twice if your running firmware is booted from the Slot 1 (Sercomm0 bootflag). The stock firmware reverses the bootflag (Sercomm0 / Sercomm1) on each firmware update. Revert to stock --------------- 1. Change the bootflag to Sercomm1 in OpenWrt CLI and then reboot: printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3 2. Optional: Update with any stock (Beeline) firmware if you want to overwrite OpenWrt in Slot 0 completely. MAC Addresses ------------- +-----+-----------+---------+ | use | address | example | +-----+-----------+---------+ | LAN | label | *:16 | | WAN | label + 1 | *:17 | | 2g | label + 4 | *:1a | | 5g | label + 5 | *:1b | +-----+-----------+---------+ The label MAC address was found in Factory 0x21000 Notes ----- 1. The following scripts are required for the build: sercomm-crypto.py - already exists in OpenWrt sercomm-partition-tag.py - already exists in OpenWrt sercomm-payload.py - already exists in OpenWrt sercomm-pid.py - new, the part of this pull request sercomm-kernel-header.py - new, the part of this pull request 2. This device (same as other Sercomm S2,S3-based devices) requires special LZMA and LOADADDR settings for successful boot: LZMA_TEXT_START=0x82800000 KERNEL_LOADADDR=0x81001000 LOADADDR=0x80001000 3. This device (same as several other Sercomm-based devices - Beeline, Netgear, Etisalat, Rostelecom) has partition map (mtd1) containing real partition offsets, which may differ from device to device depending on the number and location of bad blocks on NAND. "fixed-partitions" is used if the partition map is not found or corrupted. This behavour (it's the same as on stock firmware) is provided by MTD_SERCOMM_PARTS module. Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
2022-03-18 18:09:45 +00:00
macaddr_factory_21000: macaddr@21000 {
reg = <0x21000 0x6>;
};
};
partition@300000 {
label = "Boot Flag";
reg = <0x300000 0x100000>;
sercomm,scpart-id = <3>;
};
partition@400000 {
label = "kernel";
reg = <0x400000 0x600000>;
sercomm,scpart-id = <4>;
};
partition@a00000 {
label = "Kernel 2";
reg = <0xa00000 0x600000>;
sercomm,scpart-id = <5>;
read-only;
};
ubiconcat0: partition@1000000 {
label = "File System 1";
reg = <0x1000000 0x1800000>;
sercomm,scpart-id = <6>;
};
partition@2800000 {
label = "File System 2";
reg = <0x2800000 0x1800000>;
sercomm,scpart-id = <7>;
read-only;
};
ubiconcat1: partition@4000000 {
label = "Configuration/log";
reg = <0x4000000 0x800000>;
sercomm,scpart-id = <8>;
};
ubiconcat2: partition@4800000 {
label = "application tmp buffer (Ftool)";
reg = <0x4800000 0xc00000>;
sercomm,scpart-id = <9>;
};
ubiconcat3: partition@5400000 {
label = "container";
reg = <0x5400000 0x2800000>;
sercomm,scpart-id = <10>;
};
partition@7c00000 {
label = "bad block reserved";
reg = <0x7c00000 0x380000>;
sercomm,scpart-id = <11>;
read-only;
};
};
};
&pcie {
status = "okay";
};
&pcie0 {
wifi@0,0 {
compatible = "mediatek,mt76";
reg = <0x0000 0 0 0 0>;
ieee80211-freq-limit = <5000000 6000000>;
nvmem-cells = <&eeprom_factory_8000>, <&macaddr_factory_21000>;
nvmem-cell-names = "eeprom", "mac-address";
ramips: add support for Beeline SmartBox GIGA Beeline SmartBox GIGA is a wireless WiFi 5 router manufactured by Sercomm company. Device specification -------------------- SoC Type: MediaTek MT7621AT RAM: 256 MiB, Nanya NT5CC128M16JR-EK Flash: 128 MiB, Macronix MX30LF1G18AC Wireless 2.4 GHz (MT7603EN): b/g/n, 2x2 Wireless 5 GHz (MT7613BE): a/n/ac, 2x2 Ethernet: 3 ports - 2xGbE (WAN, LAN1), 1xFE (LAN2) USB ports: 1xUSB3.0 Button: 1 button (Reset/WPS) PCB ID: DBE00B-1.6MM LEDs: 1 RGB LED Power: 12 VDC, 1.5 A Connector type: barrel Bootloader: U-Boot Installation ----------------- 1. Downgrade stock (Beeline) firmware to v.1.0.02; 2. Give factory OpenWrt image a shorter name, e.g. 1001.img; 3. Upload and update the firmware via the original web interface. Remark: You might need make the 3rd step twice if your running firmware is booted from the Slot 1 (Sercomm0 bootflag). The stock firmware reverses the bootflag (Sercomm0 / Sercomm1) on each firmware update. Revert to stock --------------- 1. Change the bootflag to Sercomm1 in OpenWrt CLI and then reboot: printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3 2. Optional: Update with any stock (Beeline) firmware if you want to overwrite OpenWrt in Slot 0 completely. MAC Addresses ------------- +-----+-----------+---------+ | use | address | example | +-----+-----------+---------+ | LAN | label | *:16 | | WAN | label + 1 | *:17 | | 2g | label + 4 | *:1a | | 5g | label + 5 | *:1b | +-----+-----------+---------+ The label MAC address was found in Factory 0x21000 Notes ----- 1. The following scripts are required for the build: sercomm-crypto.py - already exists in OpenWrt sercomm-partition-tag.py - already exists in OpenWrt sercomm-payload.py - already exists in OpenWrt sercomm-pid.py - new, the part of this pull request sercomm-kernel-header.py - new, the part of this pull request 2. This device (same as other Sercomm S2,S3-based devices) requires special LZMA and LOADADDR settings for successful boot: LZMA_TEXT_START=0x82800000 KERNEL_LOADADDR=0x81001000 LOADADDR=0x80001000 3. This device (same as several other Sercomm-based devices - Beeline, Netgear, Etisalat, Rostelecom) has partition map (mtd1) containing real partition offsets, which may differ from device to device depending on the number and location of bad blocks on NAND. "fixed-partitions" is used if the partition map is not found or corrupted. This behavour (it's the same as on stock firmware) is provided by MTD_SERCOMM_PARTS module. Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
2022-03-18 18:09:45 +00:00
mac-address-increment = <(5)>;
};
};
&pcie1 {
wifi@0,0 {
compatible = "mediatek,mt76";
reg = <0x0000 0 0 0 0>;
ieee80211-freq-limit = <2400000 2500000>;
nvmem-cells = <&eeprom_factory_0>, <&macaddr_factory_21000>;
nvmem-cell-names = "eeprom", "mac-address";
ramips: add support for Beeline SmartBox GIGA Beeline SmartBox GIGA is a wireless WiFi 5 router manufactured by Sercomm company. Device specification -------------------- SoC Type: MediaTek MT7621AT RAM: 256 MiB, Nanya NT5CC128M16JR-EK Flash: 128 MiB, Macronix MX30LF1G18AC Wireless 2.4 GHz (MT7603EN): b/g/n, 2x2 Wireless 5 GHz (MT7613BE): a/n/ac, 2x2 Ethernet: 3 ports - 2xGbE (WAN, LAN1), 1xFE (LAN2) USB ports: 1xUSB3.0 Button: 1 button (Reset/WPS) PCB ID: DBE00B-1.6MM LEDs: 1 RGB LED Power: 12 VDC, 1.5 A Connector type: barrel Bootloader: U-Boot Installation ----------------- 1. Downgrade stock (Beeline) firmware to v.1.0.02; 2. Give factory OpenWrt image a shorter name, e.g. 1001.img; 3. Upload and update the firmware via the original web interface. Remark: You might need make the 3rd step twice if your running firmware is booted from the Slot 1 (Sercomm0 bootflag). The stock firmware reverses the bootflag (Sercomm0 / Sercomm1) on each firmware update. Revert to stock --------------- 1. Change the bootflag to Sercomm1 in OpenWrt CLI and then reboot: printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3 2. Optional: Update with any stock (Beeline) firmware if you want to overwrite OpenWrt in Slot 0 completely. MAC Addresses ------------- +-----+-----------+---------+ | use | address | example | +-----+-----------+---------+ | LAN | label | *:16 | | WAN | label + 1 | *:17 | | 2g | label + 4 | *:1a | | 5g | label + 5 | *:1b | +-----+-----------+---------+ The label MAC address was found in Factory 0x21000 Notes ----- 1. The following scripts are required for the build: sercomm-crypto.py - already exists in OpenWrt sercomm-partition-tag.py - already exists in OpenWrt sercomm-payload.py - already exists in OpenWrt sercomm-pid.py - new, the part of this pull request sercomm-kernel-header.py - new, the part of this pull request 2. This device (same as other Sercomm S2,S3-based devices) requires special LZMA and LOADADDR settings for successful boot: LZMA_TEXT_START=0x82800000 KERNEL_LOADADDR=0x81001000 LOADADDR=0x80001000 3. This device (same as several other Sercomm-based devices - Beeline, Netgear, Etisalat, Rostelecom) has partition map (mtd1) containing real partition offsets, which may differ from device to device depending on the number and location of bad blocks on NAND. "fixed-partitions" is used if the partition map is not found or corrupted. This behavour (it's the same as on stock firmware) is provided by MTD_SERCOMM_PARTS module. Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
2022-03-18 18:09:45 +00:00
mac-address-increment = <(4)>;
};
};
&gmac0 {
nvmem-cells = <&macaddr_factory_21000>;
nvmem-cell-names = "mac-address";
};
&gmac1 {
status = "okay";
label = "wan";
phy-handle = <&ethphy0>;
ramips: add support for Beeline SmartBox GIGA Beeline SmartBox GIGA is a wireless WiFi 5 router manufactured by Sercomm company. Device specification -------------------- SoC Type: MediaTek MT7621AT RAM: 256 MiB, Nanya NT5CC128M16JR-EK Flash: 128 MiB, Macronix MX30LF1G18AC Wireless 2.4 GHz (MT7603EN): b/g/n, 2x2 Wireless 5 GHz (MT7613BE): a/n/ac, 2x2 Ethernet: 3 ports - 2xGbE (WAN, LAN1), 1xFE (LAN2) USB ports: 1xUSB3.0 Button: 1 button (Reset/WPS) PCB ID: DBE00B-1.6MM LEDs: 1 RGB LED Power: 12 VDC, 1.5 A Connector type: barrel Bootloader: U-Boot Installation ----------------- 1. Downgrade stock (Beeline) firmware to v.1.0.02; 2. Give factory OpenWrt image a shorter name, e.g. 1001.img; 3. Upload and update the firmware via the original web interface. Remark: You might need make the 3rd step twice if your running firmware is booted from the Slot 1 (Sercomm0 bootflag). The stock firmware reverses the bootflag (Sercomm0 / Sercomm1) on each firmware update. Revert to stock --------------- 1. Change the bootflag to Sercomm1 in OpenWrt CLI and then reboot: printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3 2. Optional: Update with any stock (Beeline) firmware if you want to overwrite OpenWrt in Slot 0 completely. MAC Addresses ------------- +-----+-----------+---------+ | use | address | example | +-----+-----------+---------+ | LAN | label | *:16 | | WAN | label + 1 | *:17 | | 2g | label + 4 | *:1a | | 5g | label + 5 | *:1b | +-----+-----------+---------+ The label MAC address was found in Factory 0x21000 Notes ----- 1. The following scripts are required for the build: sercomm-crypto.py - already exists in OpenWrt sercomm-partition-tag.py - already exists in OpenWrt sercomm-payload.py - already exists in OpenWrt sercomm-pid.py - new, the part of this pull request sercomm-kernel-header.py - new, the part of this pull request 2. This device (same as other Sercomm S2,S3-based devices) requires special LZMA and LOADADDR settings for successful boot: LZMA_TEXT_START=0x82800000 KERNEL_LOADADDR=0x81001000 LOADADDR=0x80001000 3. This device (same as several other Sercomm-based devices - Beeline, Netgear, Etisalat, Rostelecom) has partition map (mtd1) containing real partition offsets, which may differ from device to device depending on the number and location of bad blocks on NAND. "fixed-partitions" is used if the partition map is not found or corrupted. This behavour (it's the same as on stock firmware) is provided by MTD_SERCOMM_PARTS module. Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
2022-03-18 18:09:45 +00:00
nvmem-cells = <&macaddr_factory_21000>;
nvmem-cell-names = "mac-address";
mac-address-increment = <(1)>;
};
&mdio {
ethphy0: ethernet-phy@0 {
reg = <0>;
};
};
ramips: add support for Beeline SmartBox GIGA Beeline SmartBox GIGA is a wireless WiFi 5 router manufactured by Sercomm company. Device specification -------------------- SoC Type: MediaTek MT7621AT RAM: 256 MiB, Nanya NT5CC128M16JR-EK Flash: 128 MiB, Macronix MX30LF1G18AC Wireless 2.4 GHz (MT7603EN): b/g/n, 2x2 Wireless 5 GHz (MT7613BE): a/n/ac, 2x2 Ethernet: 3 ports - 2xGbE (WAN, LAN1), 1xFE (LAN2) USB ports: 1xUSB3.0 Button: 1 button (Reset/WPS) PCB ID: DBE00B-1.6MM LEDs: 1 RGB LED Power: 12 VDC, 1.5 A Connector type: barrel Bootloader: U-Boot Installation ----------------- 1. Downgrade stock (Beeline) firmware to v.1.0.02; 2. Give factory OpenWrt image a shorter name, e.g. 1001.img; 3. Upload and update the firmware via the original web interface. Remark: You might need make the 3rd step twice if your running firmware is booted from the Slot 1 (Sercomm0 bootflag). The stock firmware reverses the bootflag (Sercomm0 / Sercomm1) on each firmware update. Revert to stock --------------- 1. Change the bootflag to Sercomm1 in OpenWrt CLI and then reboot: printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3 2. Optional: Update with any stock (Beeline) firmware if you want to overwrite OpenWrt in Slot 0 completely. MAC Addresses ------------- +-----+-----------+---------+ | use | address | example | +-----+-----------+---------+ | LAN | label | *:16 | | WAN | label + 1 | *:17 | | 2g | label + 4 | *:1a | | 5g | label + 5 | *:1b | +-----+-----------+---------+ The label MAC address was found in Factory 0x21000 Notes ----- 1. The following scripts are required for the build: sercomm-crypto.py - already exists in OpenWrt sercomm-partition-tag.py - already exists in OpenWrt sercomm-payload.py - already exists in OpenWrt sercomm-pid.py - new, the part of this pull request sercomm-kernel-header.py - new, the part of this pull request 2. This device (same as other Sercomm S2,S3-based devices) requires special LZMA and LOADADDR settings for successful boot: LZMA_TEXT_START=0x82800000 KERNEL_LOADADDR=0x81001000 LOADADDR=0x80001000 3. This device (same as several other Sercomm-based devices - Beeline, Netgear, Etisalat, Rostelecom) has partition map (mtd1) containing real partition offsets, which may differ from device to device depending on the number and location of bad blocks on NAND. "fixed-partitions" is used if the partition map is not found or corrupted. This behavour (it's the same as on stock firmware) is provided by MTD_SERCOMM_PARTS module. Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
2022-03-18 18:09:45 +00:00
&switch0 {
ports {
ramips: add support for Beeline SmartBox GIGA Beeline SmartBox GIGA is a wireless WiFi 5 router manufactured by Sercomm company. Device specification -------------------- SoC Type: MediaTek MT7621AT RAM: 256 MiB, Nanya NT5CC128M16JR-EK Flash: 128 MiB, Macronix MX30LF1G18AC Wireless 2.4 GHz (MT7603EN): b/g/n, 2x2 Wireless 5 GHz (MT7613BE): a/n/ac, 2x2 Ethernet: 3 ports - 2xGbE (WAN, LAN1), 1xFE (LAN2) USB ports: 1xUSB3.0 Button: 1 button (Reset/WPS) PCB ID: DBE00B-1.6MM LEDs: 1 RGB LED Power: 12 VDC, 1.5 A Connector type: barrel Bootloader: U-Boot Installation ----------------- 1. Downgrade stock (Beeline) firmware to v.1.0.02; 2. Give factory OpenWrt image a shorter name, e.g. 1001.img; 3. Upload and update the firmware via the original web interface. Remark: You might need make the 3rd step twice if your running firmware is booted from the Slot 1 (Sercomm0 bootflag). The stock firmware reverses the bootflag (Sercomm0 / Sercomm1) on each firmware update. Revert to stock --------------- 1. Change the bootflag to Sercomm1 in OpenWrt CLI and then reboot: printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3 2. Optional: Update with any stock (Beeline) firmware if you want to overwrite OpenWrt in Slot 0 completely. MAC Addresses ------------- +-----+-----------+---------+ | use | address | example | +-----+-----------+---------+ | LAN | label | *:16 | | WAN | label + 1 | *:17 | | 2g | label + 4 | *:1a | | 5g | label + 5 | *:1b | +-----+-----------+---------+ The label MAC address was found in Factory 0x21000 Notes ----- 1. The following scripts are required for the build: sercomm-crypto.py - already exists in OpenWrt sercomm-partition-tag.py - already exists in OpenWrt sercomm-payload.py - already exists in OpenWrt sercomm-pid.py - new, the part of this pull request sercomm-kernel-header.py - new, the part of this pull request 2. This device (same as other Sercomm S2,S3-based devices) requires special LZMA and LOADADDR settings for successful boot: LZMA_TEXT_START=0x82800000 KERNEL_LOADADDR=0x81001000 LOADADDR=0x80001000 3. This device (same as several other Sercomm-based devices - Beeline, Netgear, Etisalat, Rostelecom) has partition map (mtd1) containing real partition offsets, which may differ from device to device depending on the number and location of bad blocks on NAND. "fixed-partitions" is used if the partition map is not found or corrupted. This behavour (it's the same as on stock firmware) is provided by MTD_SERCOMM_PARTS module. Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
2022-03-18 18:09:45 +00:00
port@1 {
status = "okay";
label = "lan1";
};
port@2 {
status = "okay";
label = "lan2";
};
};
};
&uartlite3 {
status = "okay";
};
&state_default {
gpio {
groups = "i2c", "jtag";
function = "gpio";
};
};