openwrt/target/linux/ramips/dts/mt7621_xiaomi_mi-router-4a-3g-v2.dtsi

179 lines
2.8 KiB
Plaintext
Raw Normal View History

ramips: add Xiaomi Mi Router 4A Gigabit explicitly This device has previously been supported by the image for Xiaomi Mi Router 3G v2. Since this is not obvious, the 4A is marketed as a new major revision and it also seems to have a different bootloader, this will be both more tidy and more helpful for the users. Apart from that, note that there also is a 100M version of the device that uses mt7628 platform, so a specifically named image will also prevent confusion in this area. Specifications: - SoC: MediaTek MT7621 - Flash: 16 MiB NOR SPI - RAM: 128 MiB DDR3 - Ethernet: 3x 10/100/1000 Mbps (switched, 2xLAN + WAN) - WIFI0: MT7603E 2.4GHz 802.11b/g/n - WIFI1: MT7612E 5GHz 802.11ac - Antennas: 4x external (2 per radio), non-detachable - LEDs: Programmable "power" LED (two-coloured, yellow/blue) Non-programmable "internet" LED (shows WAN activity) - Buttons: Reset Installation: Bootloader won't accept any serial input unless "boot_wait" u-boot environment variable is changed to "on". Vendor firmware won't accept any serial input until "uart_en" is set to "1". Using the https://github.com/acecilia/OpenWRTInvasion exploit you can gain access to shell to enable these options: To enable uart keyboard actions - 'nvram set uart_en=1' To make uboot delay boot work - 'nvram set boot_wait=on' Set boot delay to 5 - 'nvram set bootdelay=5' Then run 'nvram commit' to make the changes permanent. Once in the shell (following the OpenWRTInvasion instructions) you can then run the following to flash OpenWrt and then reboot: 'cd /tmp; curl https://downloads.openwrt.org/...-sysupgrade.bin --output firmware.bin; mtd -e OS1 -r write firmware.bin OS1' Suggested-by: David Bentham <db260179@gmail.com> Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-11-12 15:00:10 +00:00
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
#include "mt7621.dtsi"
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
/ {
aliases {
led-boot = &led_status_yellow;
led-failsafe = &led_status_yellow;
led-running = &led_status_blue;
led-upgrade = &led_status_yellow;
label-mac-device = &wan;
};
chosen {
bootargs = "console=ttyS0,115200n8";
};
leds {
compatible = "gpio-leds";
led_status_blue: status_blue {
label = "blue:status";
gpios = <&gpio 8 GPIO_ACTIVE_LOW>;
};
led_status_yellow: status_yellow {
label = "yellow:status";
gpios = <&gpio 10 GPIO_ACTIVE_LOW>;
};
};
keys {
compatible = "gpio-keys";
reset {
label = "reset";
gpios = <&gpio 18 GPIO_ACTIVE_LOW>;
linux,code = <KEY_RESTART>;
};
};
};
&spi0 {
status = "okay";
flash@0 {
compatible = "jedec,spi-nor";
reg = <0>;
spi-max-frequency = <50000000>;
m25p,fast-read;
ramips: add Xiaomi Mi Router 4A Gigabit explicitly This device has previously been supported by the image for Xiaomi Mi Router 3G v2. Since this is not obvious, the 4A is marketed as a new major revision and it also seems to have a different bootloader, this will be both more tidy and more helpful for the users. Apart from that, note that there also is a 100M version of the device that uses mt7628 platform, so a specifically named image will also prevent confusion in this area. Specifications: - SoC: MediaTek MT7621 - Flash: 16 MiB NOR SPI - RAM: 128 MiB DDR3 - Ethernet: 3x 10/100/1000 Mbps (switched, 2xLAN + WAN) - WIFI0: MT7603E 2.4GHz 802.11b/g/n - WIFI1: MT7612E 5GHz 802.11ac - Antennas: 4x external (2 per radio), non-detachable - LEDs: Programmable "power" LED (two-coloured, yellow/blue) Non-programmable "internet" LED (shows WAN activity) - Buttons: Reset Installation: Bootloader won't accept any serial input unless "boot_wait" u-boot environment variable is changed to "on". Vendor firmware won't accept any serial input until "uart_en" is set to "1". Using the https://github.com/acecilia/OpenWRTInvasion exploit you can gain access to shell to enable these options: To enable uart keyboard actions - 'nvram set uart_en=1' To make uboot delay boot work - 'nvram set boot_wait=on' Set boot delay to 5 - 'nvram set bootdelay=5' Then run 'nvram commit' to make the changes permanent. Once in the shell (following the OpenWRTInvasion instructions) you can then run the following to flash OpenWrt and then reboot: 'cd /tmp; curl https://downloads.openwrt.org/...-sysupgrade.bin --output firmware.bin; mtd -e OS1 -r write firmware.bin OS1' Suggested-by: David Bentham <db260179@gmail.com> Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-11-12 15:00:10 +00:00
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
partition@0 {
label = "u-boot";
reg = <0x0 0x30000>;
read-only;
};
partition@30000 {
label = "u-boot-env";
reg = <0x30000 0x10000>;
read-only;
};
partition@40000 {
label = "Bdata";
reg = <0x40000 0x10000>;
read-only;
};
factory: partition@50000 {
label = "factory";
reg = <0x50000 0x10000>;
read-only;
};
partition@60000 {
label = "crash";
reg = <0x60000 0x10000>;
read-only;
};
partition@70000 {
label = "cfg_bak";
reg = <0x70000 0x10000>;
read-only;
};
partition@80000 {
label = "overlay";
reg = <0x80000 0x100000>;
read-only;
};
firmware: partition@180000 {
compatible = "denx,uimage";
label = "firmware";
reg = <0x180000 0xe80000>;
};
};
};
};
&pcie {
status = "okay";
};
&pcie0 {
wifi@0,0 {
compatible = "pci14c3,7662";
reg = <0x0000 0 0 0 0>;
mediatek,mtd-eeprom = <&factory 0x8000>;
ieee80211-freq-limit = <5000000 6000000>;
};
};
&pcie1 {
wifi@0,0 {
compatible = "pci14c3,7603";
reg = <0x0000 0 0 0 0>;
mediatek,mtd-eeprom = <&factory 0x0000>;
ieee80211-freq-limit = <2400000 2500000>;
};
};
&gmac0 {
nvmem-cells = <&macaddr_factory_e000>;
nvmem-cell-names = "mac-address";
ramips: add Xiaomi Mi Router 4A Gigabit explicitly This device has previously been supported by the image for Xiaomi Mi Router 3G v2. Since this is not obvious, the 4A is marketed as a new major revision and it also seems to have a different bootloader, this will be both more tidy and more helpful for the users. Apart from that, note that there also is a 100M version of the device that uses mt7628 platform, so a specifically named image will also prevent confusion in this area. Specifications: - SoC: MediaTek MT7621 - Flash: 16 MiB NOR SPI - RAM: 128 MiB DDR3 - Ethernet: 3x 10/100/1000 Mbps (switched, 2xLAN + WAN) - WIFI0: MT7603E 2.4GHz 802.11b/g/n - WIFI1: MT7612E 5GHz 802.11ac - Antennas: 4x external (2 per radio), non-detachable - LEDs: Programmable "power" LED (two-coloured, yellow/blue) Non-programmable "internet" LED (shows WAN activity) - Buttons: Reset Installation: Bootloader won't accept any serial input unless "boot_wait" u-boot environment variable is changed to "on". Vendor firmware won't accept any serial input until "uart_en" is set to "1". Using the https://github.com/acecilia/OpenWRTInvasion exploit you can gain access to shell to enable these options: To enable uart keyboard actions - 'nvram set uart_en=1' To make uboot delay boot work - 'nvram set boot_wait=on' Set boot delay to 5 - 'nvram set bootdelay=5' Then run 'nvram commit' to make the changes permanent. Once in the shell (following the OpenWRTInvasion instructions) you can then run the following to flash OpenWrt and then reboot: 'cd /tmp; curl https://downloads.openwrt.org/...-sysupgrade.bin --output firmware.bin; mtd -e OS1 -r write firmware.bin OS1' Suggested-by: David Bentham <db260179@gmail.com> Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-11-12 15:00:10 +00:00
};
&switch0 {
ports {
port@2 {
status = "okay";
label = "lan2";
};
port@3 {
status = "okay";
label = "lan1";
};
wan: port@4 {
status = "okay";
label = "wan";
nvmem-cells = <&macaddr_factory_e006>;
nvmem-cell-names = "mac-address";
ramips: add Xiaomi Mi Router 4A Gigabit explicitly This device has previously been supported by the image for Xiaomi Mi Router 3G v2. Since this is not obvious, the 4A is marketed as a new major revision and it also seems to have a different bootloader, this will be both more tidy and more helpful for the users. Apart from that, note that there also is a 100M version of the device that uses mt7628 platform, so a specifically named image will also prevent confusion in this area. Specifications: - SoC: MediaTek MT7621 - Flash: 16 MiB NOR SPI - RAM: 128 MiB DDR3 - Ethernet: 3x 10/100/1000 Mbps (switched, 2xLAN + WAN) - WIFI0: MT7603E 2.4GHz 802.11b/g/n - WIFI1: MT7612E 5GHz 802.11ac - Antennas: 4x external (2 per radio), non-detachable - LEDs: Programmable "power" LED (two-coloured, yellow/blue) Non-programmable "internet" LED (shows WAN activity) - Buttons: Reset Installation: Bootloader won't accept any serial input unless "boot_wait" u-boot environment variable is changed to "on". Vendor firmware won't accept any serial input until "uart_en" is set to "1". Using the https://github.com/acecilia/OpenWRTInvasion exploit you can gain access to shell to enable these options: To enable uart keyboard actions - 'nvram set uart_en=1' To make uboot delay boot work - 'nvram set boot_wait=on' Set boot delay to 5 - 'nvram set bootdelay=5' Then run 'nvram commit' to make the changes permanent. Once in the shell (following the OpenWRTInvasion instructions) you can then run the following to flash OpenWrt and then reboot: 'cd /tmp; curl https://downloads.openwrt.org/...-sysupgrade.bin --output firmware.bin; mtd -e OS1 -r write firmware.bin OS1' Suggested-by: David Bentham <db260179@gmail.com> Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-11-12 15:00:10 +00:00
};
};
};
&state_default {
gpio {
groups = "jtag", "uart2", "uart3", "wdt";
function = "gpio";
};
};
&factory {
compatible = "nvmem-cells";
#address-cells = <1>;
#size-cells = <1>;
macaddr_factory_e000: macaddr@e000 {
reg = <0xe000 0x6>;
};
macaddr_factory_e006: macaddr@e006 {
reg = <0xe006 0x6>;
};
};