openwrt/target/linux/ath79/dts/ar9344_tplink_cpe510-v1.dts

// SPDX-License-Identifier: GPL-2.0-or-later OR MIT

#include "ar9344_tplink_cpe_2port.dtsi"

/ {
	compatible = "tplink,cpe510-v1", "qca,ar9344";
	model = "TP-Link CPE510 v1";
};

&led_link4 {
	gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
};
ath79: add support for TP-Link CPE510 v1 TP-Link CPE510-v1 is an outdoor wireless CPE for 5 GHz with two Ethernet ports based on Atheros AR9334 Specifications: - 560/450/225 MHz (CPU/DDR/AHB) - 2x 10/100 Mbps Ethernet, 1x PoE-in, 1x PoE-out - 64 MB of DDR2 RAM - 8 MB of SPI-NOR Flash - 2T2R 5 GHz - 13 dBi built-in antenna - Power, LAN0, LAN1 green LEDs - 4x green RSSI LEDs Flash factory image through stock firmware WEB UI or through TFTP: To get to TFTP recovery just hold reset button while powering on for around 4-5 seconds and release. Rename factory image to recovery.bin Stock TFTP server IP:192.168.0.100 Stock device TFTP address:192.168.0.254 Based on the work of Paul Wassi <p.wassi@gmx.at> Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> 2019-07-20 10:49:20 +00:00			`// SPDX-License-Identifier: GPL-2.0-or-later OR MIT`

ath79: improve TP-Link CPE DTSI names for ar9344 SOC The initial DTSI names for the TP-Link CPE devices have become quite confusing, as several non-V1 devices now use the -v1.dtsi, the cpe510-v1.dts does not use the cpe510.dtsi, etc. This introduces a new naming scheme based on whether devices have one or two ports, which should be easier to grasp. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> 2019-11-22 10:50:00 +00:00			`#include "ar9344_tplink_cpe_2port.dtsi"`
ath79: add support for TP-Link CPE510 v1 TP-Link CPE510-v1 is an outdoor wireless CPE for 5 GHz with two Ethernet ports based on Atheros AR9334 Specifications: - 560/450/225 MHz (CPU/DDR/AHB) - 2x 10/100 Mbps Ethernet, 1x PoE-in, 1x PoE-out - 64 MB of DDR2 RAM - 8 MB of SPI-NOR Flash - 2T2R 5 GHz - 13 dBi built-in antenna - Power, LAN0, LAN1 green LEDs - 4x green RSSI LEDs Flash factory image through stock firmware WEB UI or through TFTP: To get to TFTP recovery just hold reset button while powering on for around 4-5 seconds and release. Rename factory image to recovery.bin Stock TFTP server IP:192.168.0.100 Stock device TFTP address:192.168.0.254 Based on the work of Paul Wassi <p.wassi@gmx.at> Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> 2019-07-20 10:49:20 +00:00
			`/ {`
			`compatible = "tplink,cpe510-v1", "qca,ar9344";`
			`model = "TP-Link CPE510 v1";`
			`};`
ath79: add support for TP-Link WBS210 v2 TP-Link WBS210 v2 is an outdoor wireless CPE for 2.4 GHz with two Ethernet ports based on Atheros AR9344 The device is the same as TP-Link CPE220 v2, but with higher TX power (27 dBm instead of 12 dBm) and two antenna connectors instead of built-in antennas. Specifications: - SoC: Atheros AR9344 - RAM: 64MB - Storage: 8 MB SPI NOR - Wireless: 2.4GHz 300 Mbps, 2x RP-SMA connector, 27 dBm TX power - Ethernet: 1x 10/100 Mbps with 24V POE IN, 1x 10/100 Mbps Installation: Flash factory image through stock firmware WEB UI or through TFTP To get to TFTP recovery just hold reset button while powering on for around 4-5 seconds and release. Rename factory image to recovery.bin Stock TFTP server IP: 192.168.0.100 Stock device TFTP adress: 192.168.0.254 The TP-Link WBS devices use the same GPIOs as the CPE devices, except for the link4 LED. For this one, WBS devices use "2", while CPE devices use "16". (Tested on WBS210 v2) Signed-off-by: Bernhard Geier <freifunk@geierb.de> [added comment about GPIO] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> 2019-11-03 12:58:12 +00:00
			`&led_link4 {`
			`gpios = <&gpio 16 GPIO_ACTIVE_LOW>;`
			`};`