2019-07-04 12:08:10 +00:00
|
|
|
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
2020-09-25 19:52:57 +00:00
|
|
|
|
ath79: add support for ALFA Network AP121FE
The AP121FE is a slightly modified version of already supported AP121F
model (added to ar71xx in 0c6165d21a and to ath79 in 334bbc5198).
The differences in compare to AP121F:
- no micro SD card reader
- USB data lines are included in Type-A plug
- USB bus switched to device/peripheral mode (permanently, in bootstrap)
Other than that, specifications are the same:
- Atheros AR9331
- 400/400/200 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR1)
- 16 MB of flash (SPI NOR)
- 1x 10/100 Mbps Ethernet
- 1T1R 2.4 GHz Wi-Fi, up to 15 dBm
- 1x IPEX/U.FL connector, internal PCB antenna
- 3x LED, 1x button, 1x switch
- 4-pin UART header on PCB (2 mm pitch)
- USB 2.0 Type-A plug (power and data)
Flash instruction (under U-Boot web recovery mode):
1. Configure PC with static IP 192.168.1.2/24.
2. Connect PC with RJ45 port, press the reset button, power up device,
wait for first blink of all LEDs (indicates network setup), then keep
button for 3 following blinks and release it.
3. Open 192.168.1.1 address in your browser and upload sysupgrade image.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2020-03-21 22:20:31 +00:00
|
|
|
#include "ar9331_alfa-network_ap121f.dtsi"
|
2019-07-04 12:08:10 +00:00
|
|
|
|
|
|
|
|
/ {
|
|
|
|
|
model = "ALFA Network AP121F";
|
|
|
|
|
compatible = "alfa-network,ap121f", "qca,ar9331";
|
|
|
|
|
|
|
|
|
|
leds {
|
|
|
|
|
compatible = "gpio-leds";
|
|
|
|
|
|
|
|
|
|
lan {
|
|
|
|
|
label = "ap121f:green:lan";
|
|
|
|
|
gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
|
|
|
|
|
};
|
|
|
|
|
|
2019-11-05 18:23:33 +00:00
|
|
|
led_vpn: vpn {
|
2019-07-04 12:08:10 +00:00
|
|
|
label = "ap121f:green:vpn";
|
|
|
|
|
gpios = <&gpio 27 GPIO_ACTIVE_LOW>;
|
|
|
|
|
};
|
|
|
|
|
|
|
|
|
|
wlan {
|
|
|
|
|
label = "ap121f:green:wlan";
|
|
|
|
|
gpios = <&gpio 0 GPIO_ACTIVE_HIGH>;
|
|
|
|
|
linux,default-trigger = "phy0tpt";
|
|
|
|
|
};
|
|
|
|
|
};
|
|
|
|
|
};
|
|
|
|
|
|
|
|
|
|
&usb {
|
|
|
|
|
dr_mode = "host";
|
|
|
|
|
};
|
