openwrt/target/linux/ath79/dts/qca9563_ubnt_unifiac-lite.dtsi

// SPDX-License-Identifier: GPL-2.0-or-later OR MIT

#include "qca9563_ubnt_unifiac.dtsi"

/ {
	aliases {
		label-mac-device = &eth0;
	};
};

&mdio0 {
	status = "okay";

	phy-mask = <4>;
	phy4: ethernet-phy@4 {
		phy-mode = "sgmii";
		reg = <4>;
	};
};

&eth0 {
	status = "okay";

	mtd-mac-address = <&art 0x0>;
	phy-mode = "sgmii";
	phy-handle = <&phy4>;
};
ath79: add support for Unifi AC Mesh The Unifi AC Mesh is equivalent to the Unifi AC Lite. However, for setting certain parameters with the flashed device it is helpful that the devices know their variant (e.g. automatically setting antenna gain for the different antennas in Lite and Mesh). Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> 2018-06-27 12:33:40 +00:00			`// SPDX-License-Identifier: GPL-2.0-or-later OR MIT`

			`#include "qca9563_ubnt_unifiac.dtsi"`

ath79: provide label MAC address This patch adds the label MAC address for several devices in ath79. Some devices require setting the MAC address in 02_network: For the following devices, the netif device can be linked in device tree, but the MAC address cannot be read: - alfa-network,ap121f - avm,fritz300e - ubnt-xm devices For the following devices, label MAC address is tied to lan or wan, so no node to link to exists in device tree: - adtran,bsap1800-v2 - adtran,bsap1840 - dlink,dir-842-c1/-c2/-c3 - engenius,ecb1750 - iodata,etg3-r - iodata,wn-ac1167dgr - iodata,wn-ac1600dgr - iodata,wn-ac1600dgr2 - iodata,wn-ag300dgr - nec,wg800hp - nec,wg1200cr - trendnet,tew-823dru Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> 2019-08-15 13:13:33 +00:00			`/ {`
			`aliases {`
			`label-mac-device = &eth0;`
			`};`
			`};`

ath79: add support for Unifi AC Mesh The Unifi AC Mesh is equivalent to the Unifi AC Lite. However, for setting certain parameters with the flashed device it is helpful that the devices know their variant (e.g. automatically setting antenna gain for the different antennas in Lite and Mesh). Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> 2018-06-27 12:33:40 +00:00			`&mdio0 {`
			`status = "okay";`

			`phy-mask = <4>;`
			`phy4: ethernet-phy@4 {`
			`phy-mode = "sgmii";`
			`reg = <4>;`
			`};`
			`};`

			`&eth0 {`
			`status = "okay";`

ath79: rename EEPROM to art This renames all remaining occurrences of "EEPROM" to "art" to further harmonize the partition labelling in ath79. This will help to reduce the amount of user-space code and might be beneficial when code is copy/pasted in the future. Affected are only devices from Ubiquiti, where the XM board is already using "art" in ath79. Acked-by: Piotr Dymacz <pepe2k@gmail.com> Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> 2019-11-22 13:42:47 +00:00			`mtd-mac-address = <&art 0x0>;`
ath79: add correct phy-mode for QCA9563 boards The TP-Link RE450 as well as the UniFi AC series missed the phy-mode property. Because of this, the incorrect MII phy-mode from the root dtsi was used. With Kernel 5.4, this leads to problems when used with a AR8033 PHY. The bootloader seems to leave the fiber pages selected. As there's not switch to copper pages happening in at803x_config_init due to the incorrect phy-mode, the new at803x_read_status will interpret the status of the SGMII side as the status of the copper side. Signed-off-by: David Bauer <mail@david-bauer.net> 2020-03-14 23:01:38 +00:00			`phy-mode = "sgmii";`
ath79: add support for Unifi AC Mesh The Unifi AC Mesh is equivalent to the Unifi AC Lite. However, for setting certain parameters with the flashed device it is helpful that the devices know their variant (e.g. automatically setting antenna gain for the different antennas in Lite and Mesh). Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> 2018-06-27 12:33:40 +00:00			`phy-handle = <&phy4>;`
			`};`