openwrt/target/linux/ath79/dts/qca9531_alfa-network_wifi-camppro-nano-duo.dts

61 lines
1.1 KiB
Plaintext
Raw Normal View History

ath79: add support for ALFA Network WiFi CampPro Nano Duo ALFA Network WiFi CampPro Nano Duo is a dual-radio Wi-Fi signal extender (router) in USB dongle form-factor (Type-A plug is used only for power), based on combination of two radio chipsets: Qualcomm QCA9531 (main SOC) and MediaTek MT7610U (connected over USB 2.0 interface). Specifications: - SOC: QCA9531 v2 (650 MHz) - DRAM: DDR2 128 MiB (Nanya NT5TU64M16HG-AC) - Flash: 16 MiB SPI NOR (Macronix MX25L12835F) - Ethernet: 1x 10/100 Mbps Ethernet (QCA9531) - Wi-Fi: 2x2:2 2.4 GHz Wi-Fi 4 (QCA9531) 1x1:1 2.4/5 GHz Wi-Fi 5 (MT7610U) - Antenna: 3x RP-SMA (female) antenna connectors - LED: 1x orange (RJ45, power indicator) 2x green (status + RJ45 activity/link) 1x blue (Wi-Fi 2.4 GHz status) - Button: 1x button (reset) - UART: 1x 4-pin, 2.00 mm pitch header on PCB - Other: external h/w watchdog (EM6324QYSP5B, enabled by default) GPIO-controlled USB power for MT7610U MAC addresses: - LAN: 00:c0:ca:xx:xx:6d (art 0x2, -1) - 2.4 GHz (QCA9531): 00:c0:ca:xx:xx:6e (art 0x2, device's label) - 2.4/5 GHz (MT7610U): 00:c0:ca:xx:xx:6f (from eeprom) Flash instructions: You can use sysupgrade image directly in vendor firmware which is based on LEDE/OpenWrt. Alternatively, you can use web recovery mode in U-Boot: 1. Configure PC with static IP 192.168.1.2/24. 2. Connect PC with RJ45 port, press the reset button, power up device, wait for first blink of status LED (indicates network setup), then keep button for 3 following blinks and release it. 3. Open 192.168.1.1 address in your browser and upload sysupgrade image. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2024-04-22 09:01:52 +00:00
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
#include <dt-bindings/leds/common.h>
#include "qca9531_alfa-network_r36a.dtsi"
/ {
model = "ALFA Network WiFi CampPro Nano Duo";
compatible = "alfa-network,wifi-camppro-nano-duo", "qca,qca9531";
aliases {
led-boot = &led_status;
led-failsafe = &led_status;
led-running = &led_status;
led-upgrade = &led_status;
};
leds {
compatible = "gpio-leds";
pinctrl-names = "default";
pinctrl-0 = <&enable_gpio4>;
lan {
function = LED_FUNCTION_LAN;
color = <LED_COLOR_ID_GREEN>;
gpios = <&gpio 4 GPIO_ACTIVE_LOW>;
};
led_status: status {
function = LED_FUNCTION_STATUS;
color = <LED_COLOR_ID_GREEN>;
gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
};
wlan2g {
function = LED_FUNCTION_WLAN_2GHZ;
color = <LED_COLOR_ID_BLUE>;
gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
linux,default-trigger = "phy1tpt";
};
};
};
&eth0 {
nvmem-cells = <&macaddr_art_1002 (-1)>;
nvmem-cell-names = "mac-address";
};
&eth1 {
compatible = "syscon", "simple-mfd";
};
&gpio_export {
usb-power {
gpio-export,name = "usb-power";
gpio-export,output = <0>;
gpios = <&gpio 3 GPIO_ACTIVE_LOW>;
};
};