openwrt/target/linux/ath79/dts/ar9342_ubnt_nanostation-loco-m-xw.dts

// SPDX-License-Identifier: GPL-2.0-or-later OR MIT

#include "ar9342_ubnt_xw_rssileds.dtsi"

/ {
	compatible = "ubnt,nanostation-loco-m-xw", "ubnt,xw", "qca,ar9342";
	model = "Ubiquiti Nanostation Loco M (XW)";
};

&mdio0 {
	status = "okay";

	phy1: ethernet-phy@1 {
		reg = <1>;
		phy-mode = "mii";
		reset-gpios = <&gpio 0 GPIO_ACTIVE_LOW>;
	};
};

&eth0 {
	status = "okay";

	phy-handle = <&phy1>;
};
ath79: add support for Ubiquiti NanoStation Loco M (XW) This commit adds support for the NanoStation Loco M2/M5 XW devices on the ath79 target (support was long ago available on ar71xx). Specifications: - AR9342 SoC @ 535 MHz - 64 MB RAM - 8 MB SPI flash - 1x 10/100 Mbps Ethernet, 24 Vdc PoE-in - AR8032 switch - 2T2R 5 GHz radio, 22 dBm - 13 dBi built-in antenna - POWER/LAN green LEDs - 4x RSSI LEDs (red, orange, green, green) - UART (115200 8N1) on PCB Flashing via TFTP: - Use a pointy tool (e.g., pen cap, paper clip) and keep the reset button on the device or on the PoE supply pressed - Power on the device via PoE (keep reset button pressed) - Keep pressing until LEDs flash alternatively LED1+LED3 => LED2+LED4 => LED1+LED3, etc. - Release reset button - The device starts a TFTP server at 192.168.1.20 - Set a static IP on the computer (e.g., 192.168.1.21/24) - Upload via tftp the factory image: $ tftp 192.168.1.20 tftp> bin tftp> trace tftp> put openwrt-ath79-generic-xxxxx-ubnt_nanostation-loco-m-xw-squashfs-factory.bin Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net> 2019-09-18 13:17:56 +00:00			`// SPDX-License-Identifier: GPL-2.0-or-later OR MIT`

ath79: generic: rework ar9342_ubnt_xw dtsi, and add support for Ubiquiti LiteBeam M5 (XW), Ubiquiti AirGrid M5 HP (XW), Ubiquiti PowerBeam M5 300 (XW) Add support for Ubiquiti LiteBeam M5 (XW). The device was previously supported in ar71xx. See commit: https://git.openwrt.org/?p=openwrt/openwrt.git;a=commit;h=d0988235dd277b9a832bbc4b2a100ac6e821f577 Add ALTX_MODEL for Ubiquiti AirGrid M5 HP (XW), Ubiquiti PowerBeam M5 300 (XW) in generic-ubnt.mk This models are identical (firmware-wise) to the already supported Ubiquiti Nanostation Loco M (XW) Add also Ubiquiti NanoBeam M5 to ALTX_MODEL of Ubiquiti Nanostation Loco M (XW) since it's another clone. Tested on: - Ubiquiti LiteBeam M5 (XW) - Ubiquiti PowerBeam M5 (XW) This also modify target/ath79/dts/ar9342_ubnt_xw.dtsi to use nvmem for calibration data Checked that the caldata size in the eeprom partition are actually 0x440 on: - Ubiquiti PowerBeam M5 (XW) - Ubiquiti Nanostation M5 (XW) - Ubiquiti LiteBeam M5 (XW) - Ubiquiti AirGrid M5 HP (XW) Signed-off-by: Samuele Longhi <agave@dracaena.it> 2023-12-20 18:27:15 +00:00			`#include "ar9342_ubnt_xw_rssileds.dtsi"`
ath79: add support for Ubiquiti NanoStation Loco M (XW) This commit adds support for the NanoStation Loco M2/M5 XW devices on the ath79 target (support was long ago available on ar71xx). Specifications: - AR9342 SoC @ 535 MHz - 64 MB RAM - 8 MB SPI flash - 1x 10/100 Mbps Ethernet, 24 Vdc PoE-in - AR8032 switch - 2T2R 5 GHz radio, 22 dBm - 13 dBi built-in antenna - POWER/LAN green LEDs - 4x RSSI LEDs (red, orange, green, green) - UART (115200 8N1) on PCB Flashing via TFTP: - Use a pointy tool (e.g., pen cap, paper clip) and keep the reset button on the device or on the PoE supply pressed - Power on the device via PoE (keep reset button pressed) - Keep pressing until LEDs flash alternatively LED1+LED3 => LED2+LED4 => LED1+LED3, etc. - Release reset button - The device starts a TFTP server at 192.168.1.20 - Set a static IP on the computer (e.g., 192.168.1.21/24) - Upload via tftp the factory image: $ tftp 192.168.1.20 tftp> bin tftp> trace tftp> put openwrt-ath79-generic-xxxxx-ubnt_nanostation-loco-m-xw-squashfs-factory.bin Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net> 2019-09-18 13:17:56 +00:00
			`/ {`
			`compatible = "ubnt,nanostation-loco-m-xw", "ubnt,xw", "qca,ar9342";`
			`model = "Ubiquiti Nanostation Loco M (XW)";`
			`};`

			`&mdio0 {`
			`status = "okay";`

			`phy1: ethernet-phy@1 {`
			`reg = <1>;`
			`phy-mode = "mii";`
ath79: add missing reset-gpios for NanoStation Loco M (XW) When porting support from ar71xx to ath79, the reset-gpios option was missed. Due to a hardware bug, this would eventually leave the devices with RX-deaf Ethernet PHY. Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net> 2020-02-24 17:21:49 +00:00			`reset-gpios = <&gpio 0 GPIO_ACTIVE_LOW>;`
ath79: add support for Ubiquiti NanoStation Loco M (XW) This commit adds support for the NanoStation Loco M2/M5 XW devices on the ath79 target (support was long ago available on ar71xx). Specifications: - AR9342 SoC @ 535 MHz - 64 MB RAM - 8 MB SPI flash - 1x 10/100 Mbps Ethernet, 24 Vdc PoE-in - AR8032 switch - 2T2R 5 GHz radio, 22 dBm - 13 dBi built-in antenna - POWER/LAN green LEDs - 4x RSSI LEDs (red, orange, green, green) - UART (115200 8N1) on PCB Flashing via TFTP: - Use a pointy tool (e.g., pen cap, paper clip) and keep the reset button on the device or on the PoE supply pressed - Power on the device via PoE (keep reset button pressed) - Keep pressing until LEDs flash alternatively LED1+LED3 => LED2+LED4 => LED1+LED3, etc. - Release reset button - The device starts a TFTP server at 192.168.1.20 - Set a static IP on the computer (e.g., 192.168.1.21/24) - Upload via tftp the factory image: $ tftp 192.168.1.20 tftp> bin tftp> trace tftp> put openwrt-ath79-generic-xxxxx-ubnt_nanostation-loco-m-xw-squashfs-factory.bin Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net> 2019-09-18 13:17:56 +00:00			`};`
			`};`

			`&eth0 {`
			`status = "okay";`

			`phy-handle = <&phy1>;`
			`};`