openwrt/target/linux/ath79/dts/ar934x_ruckus_zf73xx.dtsi

// SPDX-License-Identifier: GPL-2.0-or-later OR MIT

#include "ar9344.dtsi"

#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
#include <dt-bindings/leds/common.h>
#include <dt-bindings/mtd/partitions/uimage.h>

/ {
	aliases {
		led-boot = &power_green;
		led-failsafe = &power_red;
		led-running = &power_green;
		led-upgrade = &power_red;
	};

	firmware-concat {
		compatible = "mtd-concat";
		devices = <&fwconcat0 &fwconcat1>;

		partitions {
			compatible = "fixed-partitions";
			#address-cells = <1>;
			#size-cells = <1>;

			partition@0 {
				reg = <0x0 0x1f00000>;
				label = "firmware";
				compatible = "openwrt,uimage", "denx,uimage";
			};
		};
	};

	keys {
		compatible = "gpio-keys";

		reset {
			linux,code = <KEY_RESTART>;
			label = "Reset button";
			gpios = <&gpio 0 GPIO_ACTIVE_HIGH>;
			debounce-interval = <50>;
		};
	};

	leds {
		compatible = "gpio-leds";
		pinctrl-names = "default";
		pinctrl-0 = <&enable_gpio_11>,
			    <&enable_gpio_16>,
			    <&enable_gpio_4>,
			    <&clks_disable_pins>;

		power_green: power-green {
			function = LED_FUNCTION_POWER;
			color = <LED_COLOR_ID_GREEN>;
			gpios = <&gpio 4 GPIO_ACTIVE_LOW>;
			default-state = "on";
		};
	};

	reserved-memory {
		#address-cells = <1>;
		#size-cells = <1>;
		ranges;

		ruckus-himem@7ff0000 {
			/* Ruckus Himem area used to control
			 * redundant boot image selection
			 */
			compatible = "nvmem-rmem";
			reg = <0x7ff0000 0x10000>;
			no-map;
		};
	};
};

&ref {
	clock-frequency = <40000000>;
};

&spi {
	status = "okay";

	flash@0 {
		compatible = "jedec,spi-nor";
		reg = <0>;
		spi-max-frequency = <25000000>;

		partitions {
			compatible = "fixed-partitions";
			#address-cells = <1>;
			#size-cells = <1>;

			partition@0 {
				label = "u-boot";
				reg = <0x000000 0x040000>;
				read-only;
			};

			fwconcat0: partition@40000 {
				label = "fwconcat0";
				reg = <0x040000 0xf00000>;
			};

			partition@f40000 {
				compatible = "u-boot,env";
				label = "u-boot-env";
				reg = <0xf40000 0x040000>;
			};

			board_data: partition@f80000 {
				label = "board-data";
				reg = <0xf80000 0x080000>;
				read-only;
			};

			fwconcat1: partition@1000000 {
				label = "fwconcat1";
				reg = <0x1000000 0x1000000>;
			};
		};
	};
};

&mdio0 {
	status = "okay";

	phy: ethernet-phy@6 {
		compatible = "ethernet-phy-ieee802.3-c22";
		reg = <6>;
	};
};

&eth0 {
	status = "okay";
	pll-data = <0x02000000 0x00000101 0x00001313>;
	phy-mode = "rgmii-id";
	phy-handle = <&phy>;

	nvmem-cell-names = "mac-address";

	gmac-config {
		device = <&gmac>;
		rgmii-gmac0 = <1>;
		rxdv-delay = <3>;
		rxd-delay = <3>;
	};
};

&pinmux {
	clks_disable_pins: pinmux_clks_disable_pins {
		pinctrl-single,bits = <0x40 0x0 0x20>;
	};

	enable_gpio_4: pinctrl_enable_gpio_4 {
		pinctrl-single,bits = <0x4 0x0 0xff>;
	};

	enable_gpio_11: pinctrl_enable_gpio_11 {
		pinctrl-single,bits = <0x8 0x0 0xff000000>;
	};

	enable_gpio_16: pinctrl_enable_gpio_16 {
		pinctrl-single,bits = <0x10 0x0 0xff>;
	};
};

&wmac {
	status = "okay";

	nvmem-cells = <&macaddr_board_data_60>, <&cal_board_data_41000>;
	nvmem-cell-names = "mac-address", "calibration";
};

&usb {
	status = "okay";
};

&usb_phy {
	status = "okay";
};