ramips: add support for ALFA Network AX1800RM
ALFA Network AX1800RM (FCC ID: 2AB877621) is a dual-band Wi-Fi 6
(AX1800) router, based on MediaTek MT7621A + MT79x5D platform.
Specifications:
- SOC: MT7621A (880 MHz)
- DRAM: DDR3 256 MiB (Nanya NT5CC128M16JR-EK)
- Flash: 16 MiB SPI NOR (EN25QH128A-104HIP)
- Ethernet: 4x 10/100/1000 Mbps (SOC's built-in switch)
- Wi-Fi: 2x2:2 2.4/5 GHz (MT7905DAN + MT7975DN)
(MT7905DAN doesn't support background DFS scan/BT)
- LED: 6x green, 1x green/red
- Buttons: 2x (reset, WPS)
- Antenna: 4x external, non-detachable omnidirectional
- UART: 1x 4-pin (2.54 mm pitch, J4, not populated)
- Power: 12 V DC/1 A (DC jack)
MAC addresses:
LAN: 00:c0:ca:xx:xx:4e (factory 0x4, +2)
WAN: 00:c0:ca:xx:xx:4f (factory 0x4, +3)
2.4 GHz: 00:c0:ca:xx:xx:4c (factory 0x4, device's label)
5 GHz: 00:c0:ca:xx:xx:4c (factory 0xa)
Flash instructions for web-based U-Boot recovery:
1. Power the device with WPS button pressed and wait around 10 seconds.
2. Setup static IP 192.168.1.2/24 on your PC.
3. Go to 192.168.1.1 in browser and upload 'recovery' image.
The device runs LEDE 17.01 (kernel 4.4.x) based firmware with 'failsafe'
mode available which allows alternative upgrade method:
1. Run device in 'failsafe' mode and change password for default user.
2. SSH to the device, transfer 'sysupgrade' image and perform upgrade
in forced mode, without preserving settings: 'sysupgrade -n -F ...'.
Other notes:
If you own early version of this device, the vendor firmware might
refuse OpenWrt image because of missing custom header. In that case,
ask vendor's customer support for stock firmware without custom header
support/requirement.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2023-07-28 09:41:14 +00:00
|
|
|
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
|
|
|
|
|
|
|
#include "mt7621.dtsi"
|
|
|
|
|
|
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
|
|
#include <dt-bindings/input/input.h>
|
|
|
|
#include <dt-bindings/leds/common.h>
|
|
|
|
|
|
|
|
/ {
|
|
|
|
compatible = "alfa-network,ax1800rm", "mediatek,mt7621-soc";
|
|
|
|
model = "ALFA Network AX1800RM";
|
|
|
|
|
|
|
|
aliases {
|
|
|
|
label-mac-device = &wifi0;
|
|
|
|
led-boot = &led_power;
|
|
|
|
led-failsafe = &led_wan_red;
|
|
|
|
led-running = &led_power;
|
|
|
|
led-upgrade = &led_power;
|
|
|
|
};
|
|
|
|
|
|
|
|
chosen {
|
|
|
|
bootargs = "console=ttyS0,115200";
|
|
|
|
};
|
|
|
|
|
|
|
|
keys {
|
|
|
|
compatible = "gpio-keys";
|
|
|
|
|
|
|
|
reset {
|
|
|
|
label = "reset";
|
|
|
|
gpios = <&gpio 18 GPIO_ACTIVE_LOW>;
|
|
|
|
linux,code = <KEY_RESTART>;
|
|
|
|
};
|
|
|
|
|
|
|
|
wps {
|
|
|
|
label = "wps";
|
|
|
|
gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
|
|
|
|
linux,code = <KEY_WPS_BUTTON>;
|
|
|
|
};
|
|
|
|
};
|
|
|
|
|
|
|
|
leds {
|
|
|
|
compatible = "gpio-leds";
|
|
|
|
|
|
|
|
lan1 {
|
|
|
|
color = <LED_COLOR_ID_GREEN>;
|
|
|
|
function = LED_FUNCTION_LAN;
|
|
|
|
gpios = <&gpio 3 GPIO_ACTIVE_HIGH>;
|
|
|
|
};
|
|
|
|
|
|
|
|
lan2 {
|
|
|
|
color = <LED_COLOR_ID_GREEN>;
|
|
|
|
function = LED_FUNCTION_LAN;
|
|
|
|
gpios = <&gpio 4 GPIO_ACTIVE_LOW>;
|
|
|
|
};
|
|
|
|
|
|
|
|
lan3 {
|
|
|
|
color = <LED_COLOR_ID_GREEN>;
|
|
|
|
function = LED_FUNCTION_LAN;
|
|
|
|
gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
|
|
|
|
};
|
|
|
|
|
|
|
|
led_power: power {
|
|
|
|
color = <LED_COLOR_ID_GREEN>;
|
|
|
|
function = LED_FUNCTION_POWER;
|
|
|
|
gpios = <&gpio 7 GPIO_ACTIVE_LOW>;
|
|
|
|
};
|
|
|
|
|
|
|
|
wan_green {
|
|
|
|
color = <LED_COLOR_ID_GREEN>;
|
|
|
|
function = LED_FUNCTION_WAN;
|
|
|
|
gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
|
|
|
|
};
|
|
|
|
|
|
|
|
led_wan_red: wan_red {
|
|
|
|
color = <LED_COLOR_ID_RED>;
|
|
|
|
function = LED_FUNCTION_WAN;
|
|
|
|
gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
|
|
|
|
};
|
|
|
|
};
|
|
|
|
};
|
|
|
|
|
|
|
|
&spi0 {
|
|
|
|
status = "okay";
|
|
|
|
|
|
|
|
flash@0 {
|
|
|
|
compatible = "jedec,spi-nor";
|
|
|
|
reg = <0>;
|
|
|
|
spi-max-frequency = <50000000>;
|
|
|
|
m25p,fast-read;
|
|
|
|
|
|
|
|
partitions {
|
|
|
|
compatible = "fixed-partitions";
|
|
|
|
#address-cells = <1>;
|
|
|
|
#size-cells = <1>;
|
|
|
|
|
|
|
|
partition@0 {
|
|
|
|
label = "u-boot";
|
|
|
|
reg = <0x0 0x30000>;
|
|
|
|
read-only;
|
|
|
|
};
|
|
|
|
|
|
|
|
partition@30000 {
|
|
|
|
label = "u-boot-env";
|
|
|
|
reg = <0x30000 0x10000>;
|
|
|
|
};
|
|
|
|
|
|
|
|
partition@40000 {
|
|
|
|
label = "boot-config";
|
|
|
|
reg = <0x40000 0x10000>;
|
|
|
|
read-only;
|
|
|
|
};
|
|
|
|
|
|
|
|
partition@50000 {
|
|
|
|
label = "factory";
|
|
|
|
reg = <0x50000 0x10000>;
|
|
|
|
read-only;
|
|
|
|
|
|
|
|
nvmem-layout {
|
|
|
|
compatible = "fixed-layout";
|
|
|
|
#address-cells = <1>;
|
|
|
|
#size-cells = <1>;
|
|
|
|
|
|
|
|
eeprom: eeprom@0 {
|
|
|
|
reg = <0x0 0xe00>;
|
|
|
|
};
|
|
|
|
|
|
|
|
macaddr: macaddr@4 {
|
|
|
|
compatible = "mac-base";
|
|
|
|
reg = <0x4 0x6>;
|
|
|
|
#nvmem-cell-cells = <1>;
|
|
|
|
};
|
|
|
|
};
|
|
|
|
};
|
|
|
|
|
|
|
|
partition@60000 {
|
|
|
|
label = "permanent_config";
|
|
|
|
reg = <0x60000 0x80000>;
|
|
|
|
read-only;
|
|
|
|
};
|
|
|
|
|
|
|
|
partition@e0000 {
|
|
|
|
compatible = "denx,fit";
|
|
|
|
label = "firmware";
|
|
|
|
reg = <0xe0000 0xf20000>;
|
|
|
|
};
|
|
|
|
};
|
|
|
|
};
|
|
|
|
};
|
|
|
|
|
|
|
|
&pcie {
|
|
|
|
status = "okay";
|
|
|
|
};
|
|
|
|
|
|
|
|
&pcie1 {
|
|
|
|
wifi0: wifi@0,0 {
|
|
|
|
compatible = "mediatek,mt76";
|
|
|
|
reg = <0x0000 0 0 0 0>;
|
|
|
|
|
|
|
|
nvmem-cells = <&eeprom>;
|
|
|
|
nvmem-cell-names = "eeprom";
|
|
|
|
mediatek,disable-radar-background;
|
|
|
|
};
|
|
|
|
};
|
|
|
|
|
|
|
|
&gmac0 {
|
|
|
|
nvmem-cells = <&macaddr 2>;
|
|
|
|
nvmem-cell-names = "mac-address";
|
|
|
|
};
|
|
|
|
|
|
|
|
&gmac1 {
|
|
|
|
status = "okay";
|
|
|
|
label = "wan";
|
|
|
|
phy-handle = <ðphy4>;
|
|
|
|
|
|
|
|
nvmem-cells = <&macaddr 3>;
|
|
|
|
nvmem-cell-names = "mac-address";
|
|
|
|
};
|
|
|
|
|
ramips: mt7621-dts: describe switch PHYs and adjust PHY muxing
Currently, the MT7530 DSA subdriver configures the MT7530 switch to provide
direct access to switch PHYs, meaning, the switch PHYs listen on the MDIO
bus the switch listens on. The PHY muxing feature makes use of this.
This is problematic as the PHY may be attached before the switch is
initialised, in which case, the PHY will fail to be attached.
Since commit 91374ba537bd ("net: dsa: mt7530: support OF-based registration
of switch MDIO bus") on mainline Linux, we can describe the switch PHYs on
the MDIO bus of the switch on the device tree.
When the PHY is described this way, the switch will be initialised first,
then the switch MDIO bus will be registered. Only after these steps, the
PHY will be attached.
Describe the switch PHYs on mt7621.dtsi and remove defining the switch PHY
on the SoC's mdio bus node. When the PHY muxing is in use, the interrupts
for the muxed PHY won't work, therefore delete the "interrupts" property on
the devices where the PHY muxing feature is in use.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
2024-04-28 19:52:51 +00:00
|
|
|
ðphy4 {
|
|
|
|
/delete-property/ interrupts;
|
ramips: add support for ALFA Network AX1800RM
ALFA Network AX1800RM (FCC ID: 2AB877621) is a dual-band Wi-Fi 6
(AX1800) router, based on MediaTek MT7621A + MT79x5D platform.
Specifications:
- SOC: MT7621A (880 MHz)
- DRAM: DDR3 256 MiB (Nanya NT5CC128M16JR-EK)
- Flash: 16 MiB SPI NOR (EN25QH128A-104HIP)
- Ethernet: 4x 10/100/1000 Mbps (SOC's built-in switch)
- Wi-Fi: 2x2:2 2.4/5 GHz (MT7905DAN + MT7975DN)
(MT7905DAN doesn't support background DFS scan/BT)
- LED: 6x green, 1x green/red
- Buttons: 2x (reset, WPS)
- Antenna: 4x external, non-detachable omnidirectional
- UART: 1x 4-pin (2.54 mm pitch, J4, not populated)
- Power: 12 V DC/1 A (DC jack)
MAC addresses:
LAN: 00:c0:ca:xx:xx:4e (factory 0x4, +2)
WAN: 00:c0:ca:xx:xx:4f (factory 0x4, +3)
2.4 GHz: 00:c0:ca:xx:xx:4c (factory 0x4, device's label)
5 GHz: 00:c0:ca:xx:xx:4c (factory 0xa)
Flash instructions for web-based U-Boot recovery:
1. Power the device with WPS button pressed and wait around 10 seconds.
2. Setup static IP 192.168.1.2/24 on your PC.
3. Go to 192.168.1.1 in browser and upload 'recovery' image.
The device runs LEDE 17.01 (kernel 4.4.x) based firmware with 'failsafe'
mode available which allows alternative upgrade method:
1. Run device in 'failsafe' mode and change password for default user.
2. SSH to the device, transfer 'sysupgrade' image and perform upgrade
in forced mode, without preserving settings: 'sysupgrade -n -F ...'.
Other notes:
If you own early version of this device, the vendor firmware might
refuse OpenWrt image because of missing custom header. In that case,
ask vendor's customer support for stock firmware without custom header
support/requirement.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2023-07-28 09:41:14 +00:00
|
|
|
};
|
|
|
|
|
|
|
|
&switch0 {
|
|
|
|
ports {
|
|
|
|
port@0 {
|
|
|
|
status = "okay";
|
|
|
|
label = "lan1";
|
|
|
|
};
|
|
|
|
|
|
|
|
port@1 {
|
|
|
|
status = "okay";
|
|
|
|
label = "lan2";
|
|
|
|
};
|
|
|
|
|
|
|
|
port@2 {
|
|
|
|
status = "okay";
|
|
|
|
label = "lan3";
|
|
|
|
};
|
|
|
|
};
|
|
|
|
};
|
|
|
|
|
|
|
|
&state_default {
|
|
|
|
gpio {
|
|
|
|
groups = "i2c", "jtag", "uart3", "wdt";
|
|
|
|
function = "gpio";
|
|
|
|
};
|
|
|
|
};
|