openwrt/target/linux/bcm27xx/patches-6.6/950-0467-spi-bcm2835-Use-phys-addresses-for-slave-DMA-config.patch

88 lines
3.1 KiB
Diff
Raw Normal View History

From 383c5d7461002d945e31b1b1e542950f8f9bdaf8 Mon Sep 17 00:00:00 2001
From: Phil Elwell <phil@raspberrypi.com>
Date: Thu, 11 May 2023 16:27:06 +0100
Subject: [PATCH 0467/1085] spi: bcm2835: Use phys addresses for slave DMA
config
Contrary to what struct snd_dmaengine_dai_dma_data suggests, the
configuration of addresses of DMA slave interfaces should be done in
CPU physical addresses.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
---
drivers/spi/spi-bcm2835.c | 22 +++++++---------------
1 file changed, 7 insertions(+), 15 deletions(-)
--- a/drivers/spi/spi-bcm2835.c
+++ b/drivers/spi/spi-bcm2835.c
@@ -116,6 +116,7 @@ MODULE_PARM_DESC(polling_limit_us,
*/
struct bcm2835_spi {
void __iomem *regs;
+ phys_addr_t phys_addr;
struct clk *clk;
unsigned long clk_hz;
int irq;
@@ -887,19 +888,8 @@ static int bcm2835_dma_init(struct spi_c
struct bcm2835_spi *bs)
{
struct dma_slave_config slave_config;
- const __be32 *addr;
- dma_addr_t dma_reg_base;
int ret;
- /* base address in dma-space */
- addr = of_get_address(ctlr->dev.of_node, 0, NULL, NULL);
- if (!addr) {
- dev_err(dev, "could not get DMA-register address - not using dma mode\n");
- /* Fall back to interrupt mode */
- return 0;
- }
- dma_reg_base = be32_to_cpup(addr);
-
/* get tx/rx dma */
ctlr->dma_tx = dma_request_chan(dev, "tx");
if (IS_ERR(ctlr->dma_tx)) {
@@ -921,7 +911,7 @@ static int bcm2835_dma_init(struct spi_c
* or, in case of an RX-only transfer, cyclically copies from the zero
* page to the FIFO using a preallocated, reusable descriptor.
*/
- slave_config.dst_addr = (u32)(dma_reg_base + BCM2835_SPI_FIFO);
+ slave_config.dst_addr = bs->phys_addr + BCM2835_SPI_FIFO;
slave_config.dst_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES;
ret = dmaengine_slave_config(ctlr->dma_tx, &slave_config);
@@ -960,9 +950,9 @@ static int bcm2835_dma_init(struct spi_c
* RX FIFO or, in case of a TX-only transfer, cyclically writes a
* precalculated value to the CS register to clear the RX FIFO.
*/
- slave_config.src_addr = (u32)(dma_reg_base + BCM2835_SPI_FIFO);
+ slave_config.src_addr = bs->phys_addr + BCM2835_SPI_FIFO;
slave_config.src_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES;
- slave_config.dst_addr = (u32)(dma_reg_base + BCM2835_SPI_CS);
+ slave_config.dst_addr = bs->phys_addr + BCM2835_SPI_CS;
slave_config.dst_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES;
ret = dmaengine_slave_config(ctlr->dma_rx, &slave_config);
@@ -1336,6 +1326,7 @@ static int bcm2835_spi_probe(struct plat
{
struct spi_controller *ctlr;
struct bcm2835_spi *bs;
+ struct resource *iomem;
int err;
ctlr = devm_spi_alloc_host(&pdev->dev, sizeof(*bs));
@@ -1358,10 +1349,11 @@ static int bcm2835_spi_probe(struct plat
bs = spi_controller_get_devdata(ctlr);
bs->ctlr = ctlr;
- bs->regs = devm_platform_ioremap_resource(pdev, 0);
+ bs->regs = devm_platform_get_and_ioremap_resource(pdev, 0, &iomem);
if (IS_ERR(bs->regs))
return PTR_ERR(bs->regs);
+ bs->phys_addr = iomem->start;
bs->clk = devm_clk_get(&pdev->dev, NULL);
if (IS_ERR(bs->clk))
return dev_err_probe(&pdev->dev, PTR_ERR(bs->clk),