openwrt/target/linux/ramips/dts/mt7621_dlink_flash-16m-a1.dtsi

65 lines
1.1 KiB
Plaintext
Raw Normal View History

ramips: add support for D-Link DIR-867/DIR-882 A1 This patch adds support for D-Link DIR-867 A1 and D-Link DIR-882 A1. Given the similarity of these devices, this patch also introduces a common DTS shared between DIR-867 A1, DIR-878 A1 and DIR-882 A1. Specifications: * Board: AP-MTKH7-0002 * SoC: MediaTek MT7621AT * RAM: 128 MB (DDR3) * Flash: 16 MB (SPI NOR) * WiFi: MediaTek MT7615N (x2) * Switch: 1 WAN, 4 LAN (Gigabit) * Ports: 1 USB 2.0, 1 USB 3.0 * Buttons: Reset, WiFi Toggle, WPS * LEDs: Power (green/orange), Internet (green/orange), WiFi 2.4G (green), WiFi 5G (green), USB 2.0 (green), USB 3.0 (green) Notes: * WiFi 2.4G and WiFi 5G LEDs are wired directly to the wireless chips * DIR-867 wireless chips are limited to 3x3 streams at hardware level * USB ports and related LEDs available only on DIR-882 Serial port: * Parameters: 57600, 8N1 * Location: J1 header (close to the Reset, WiFi and WPS buttons) * Pinout: 1 - VCC 2 - RXD 3 - TXD 4 - GND Installation: * D-Link Recovery GUI: power down the router, press and hold the reset button, then re-plug it. Keep the reset button pressed until the power LED starts flashing orange, manually assign a static IP address under the 192.168.0.xxx subnet (e.g. 192.168.0.2) and go to http://192.168.0.1 * Some modern browsers may have problems flashing via the Recovery GUI, if that occurs consider uploading the firmware through cURL: curl -v -i -F "firmware=@file.bin" 192.168.0.1 Signed-off-by: Mateus B. Cassiano <mbc07@live.com> [move DEVICE_VARIANT to individual definitions] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-15 21:45:39 +00:00
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
&spi0 {
status = "okay";
flash@0 {
compatible = "jedec,spi-nor";
reg = <0>;
spi-max-frequency = <50000000>;
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
partition@0 {
label = "u-boot";
reg = <0x0 0x30000>;
read-only;
};
partition@30000 {
label = "u-boot-env";
reg = <0x30000 0x10000>;
read-only;
};
factory: partition@40000 {
label = "factory";
reg = <0x40000 0x20000>;
read-only;
nvmem-layout {
compatible = "fixed-layout";
#address-cells = <1>;
#size-cells = <1>;
eeprom_factory_0: eeprom@0 {
reg = <0x0 0x4da8>;
};
eeprom_factory_8000: eeprom@8000 {
reg = <0x8000 0x4da8>;
};
macaddr_factory_e000: macaddr@e000 {
reg = <0xe000 0x6>;
};
macaddr_factory_e006: macaddr@e006 {
reg = <0xe006 0x6>;
};
};
ramips: add support for D-Link DIR-867/DIR-882 A1 This patch adds support for D-Link DIR-867 A1 and D-Link DIR-882 A1. Given the similarity of these devices, this patch also introduces a common DTS shared between DIR-867 A1, DIR-878 A1 and DIR-882 A1. Specifications: * Board: AP-MTKH7-0002 * SoC: MediaTek MT7621AT * RAM: 128 MB (DDR3) * Flash: 16 MB (SPI NOR) * WiFi: MediaTek MT7615N (x2) * Switch: 1 WAN, 4 LAN (Gigabit) * Ports: 1 USB 2.0, 1 USB 3.0 * Buttons: Reset, WiFi Toggle, WPS * LEDs: Power (green/orange), Internet (green/orange), WiFi 2.4G (green), WiFi 5G (green), USB 2.0 (green), USB 3.0 (green) Notes: * WiFi 2.4G and WiFi 5G LEDs are wired directly to the wireless chips * DIR-867 wireless chips are limited to 3x3 streams at hardware level * USB ports and related LEDs available only on DIR-882 Serial port: * Parameters: 57600, 8N1 * Location: J1 header (close to the Reset, WiFi and WPS buttons) * Pinout: 1 - VCC 2 - RXD 3 - TXD 4 - GND Installation: * D-Link Recovery GUI: power down the router, press and hold the reset button, then re-plug it. Keep the reset button pressed until the power LED starts flashing orange, manually assign a static IP address under the 192.168.0.xxx subnet (e.g. 192.168.0.2) and go to http://192.168.0.1 * Some modern browsers may have problems flashing via the Recovery GUI, if that occurs consider uploading the firmware through cURL: curl -v -i -F "firmware=@file.bin" 192.168.0.1 Signed-off-by: Mateus B. Cassiano <mbc07@live.com> [move DEVICE_VARIANT to individual definitions] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-15 21:45:39 +00:00
};
partition@60000 {
compatible = "openwrt,uimage", "denx,uimage";
openwrt,padding = <96>;
ramips: add support for D-Link DIR-867/DIR-882 A1 This patch adds support for D-Link DIR-867 A1 and D-Link DIR-882 A1. Given the similarity of these devices, this patch also introduces a common DTS shared between DIR-867 A1, DIR-878 A1 and DIR-882 A1. Specifications: * Board: AP-MTKH7-0002 * SoC: MediaTek MT7621AT * RAM: 128 MB (DDR3) * Flash: 16 MB (SPI NOR) * WiFi: MediaTek MT7615N (x2) * Switch: 1 WAN, 4 LAN (Gigabit) * Ports: 1 USB 2.0, 1 USB 3.0 * Buttons: Reset, WiFi Toggle, WPS * LEDs: Power (green/orange), Internet (green/orange), WiFi 2.4G (green), WiFi 5G (green), USB 2.0 (green), USB 3.0 (green) Notes: * WiFi 2.4G and WiFi 5G LEDs are wired directly to the wireless chips * DIR-867 wireless chips are limited to 3x3 streams at hardware level * USB ports and related LEDs available only on DIR-882 Serial port: * Parameters: 57600, 8N1 * Location: J1 header (close to the Reset, WiFi and WPS buttons) * Pinout: 1 - VCC 2 - RXD 3 - TXD 4 - GND Installation: * D-Link Recovery GUI: power down the router, press and hold the reset button, then re-plug it. Keep the reset button pressed until the power LED starts flashing orange, manually assign a static IP address under the 192.168.0.xxx subnet (e.g. 192.168.0.2) and go to http://192.168.0.1 * Some modern browsers may have problems flashing via the Recovery GUI, if that occurs consider uploading the firmware through cURL: curl -v -i -F "firmware=@file.bin" 192.168.0.1 Signed-off-by: Mateus B. Cassiano <mbc07@live.com> [move DEVICE_VARIANT to individual definitions] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-15 21:45:39 +00:00
label = "firmware";
reg = <0x60000 0xfa0000>;
};
};
};
};