mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-24 07:46:48 +00:00
93 lines
3.0 KiB
Diff
93 lines
3.0 KiB
Diff
|
--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
|
||
|
|
+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
|
||
|
|
@@ -483,6 +483,26 @@ static struct board_info __initdata boar
|
||
|
|
.ext_irq = 2,
|
||
|
|
},
|
||
|
|
};
|
||
|
|
+
|
||
|
|
+static struct board_info __initdata board_V2500V_BB = {
|
||
|
|
+ .name = "V2500V_BB",
|
||
|
|
+ .expected_cpu_id = 0x6348,
|
||
|
|
+
|
||
|
|
+ .has_enet0 = 1,
|
||
|
|
+ .has_enet1 = 1,
|
||
|
|
+ .has_pci = 1,
|
||
|
|
+
|
||
|
|
+ .enet0 = {
|
||
|
|
+ .has_phy = 1,
|
||
|
|
+ .use_internal_phy = 1,
|
||
|
|
+ },
|
||
|
|
+ .enet1 = {
|
||
|
|
+ .has_phy = 1,
|
||
|
|
+ .phy_id = 0,
|
||
|
|
+ .force_speed_100 = 1,
|
||
|
|
+ .force_duplex_full = 1,
|
||
|
|
+ },
|
||
|
|
+};
|
||
|
|
#endif /* CONFIG_BCM63XX_CPU_6348 */
|
||
|
|
|
||
|
|
/*
|
||
|
|
@@ -755,6 +775,7 @@ static const struct board_info __initcon
|
||
|
|
&board_96348_D4PW,
|
||
|
|
&board_spw500v,
|
||
|
|
&board_96348sv,
|
||
|
|
+ &board_V2500V_BB,
|
||
|
|
#endif
|
||
|
|
|
||
|
|
#ifdef CONFIG_BCM63XX_CPU_6358
|
||
|
|
@@ -794,6 +815,7 @@ static struct of_device_id const bcm963x
|
||
|
|
{ .compatible = "brcm,bcm96348gw-10", .data = &board_96348gw_10, },
|
||
|
|
{ .compatible = "brcm,bcm96348gw-11", .data = &board_96348gw_11, },
|
||
|
|
{ .compatible = "brcm,bcm96348gw-a", .data = &board_96348gw_a, },
|
||
|
|
+ { .compatible = "bt,v2500v-bb", .data = &board_V2500V_BB, },
|
||
|
|
{ .compatible = "d-link,dsl-2640b-b", .data = &board_96348_D4PW, },
|
||
|
|
{ .compatible = "davolink,dv-201amr", .data = &board_DV201AMR, },
|
||
|
|
{ .compatible = "dynalink,rta1025w", .data = &board_rta1025w_16, },
|
||
|
|
@@ -853,6 +875,22 @@ void __init board_bcm963xx_init(void)
|
||
|
|
val &= MPI_CSBASE_BASE_MASK;
|
||
|
|
}
|
||
|
|
boot_addr = (u8 *)KSEG1ADDR(val);
|
||
|
|
+ pr_info("Boot address 0x%08x\n",(unsigned int)boot_addr);
|
||
|
|
+
|
||
|
|
+ /* BT Voyager 2500V (RTA1046VW PCB) has 8 Meg flash used as two */
|
||
|
|
+ /* banks of 4 Meg. The byte at 0xBF800000 identifies the back to use.*/
|
||
|
|
+ /* Loading firmware from the CFE Prompt always loads to Bank 0 */
|
||
|
|
+ /* Do an early check of CFE and then select bank 0 */
|
||
|
|
+
|
||
|
|
+ if (boot_addr == (u8 *)0xbf800000) {
|
||
|
|
+ u8 *tmp_boot_addr = (u8*)0xbfc00000;
|
||
|
|
+
|
||
|
|
+ bcm63xx_nvram_init(tmp_boot_addr + BCM963XX_NVRAM_OFFSET);
|
||
|
|
+ if (!strcmp(bcm63xx_nvram_get_name(), "V2500V_BB")) {
|
||
|
|
+ pr_info("V2500V: nvram bank 0\n");
|
||
|
|
+ boot_addr = tmp_boot_addr;
|
||
|
|
+ }
|
||
|
|
+ }
|
||
|
|
|
||
|
|
/* dump cfe version */
|
||
|
|
cfe = boot_addr + BCM963XX_CFE_VERSION_OFFSET;
|
||
|
|
--- a/arch/mips/bcm63xx/dev-flash.c
|
||
|
|
+++ b/arch/mips/bcm63xx/dev-flash.c
|
||
|
|
@@ -21,6 +21,7 @@
|
||
|
|
#include <linux/spi/spi.h>
|
||
|
|
#include <linux/spi/flash.h>
|
||
|
|
|
||
|
|
+#include <bcm63xx_board.h>
|
||
|
|
#include <bcm63xx_cpu.h>
|
||
|
|
#include <bcm63xx_dev_flash.h>
|
||
|
|
#include <bcm63xx_regs.h>
|
||
|
|
@@ -247,6 +248,13 @@ int __init bcm63xx_flash_register(void)
|
||
|
|
val = bcm_mpi_readl(MPI_CSBASE_REG(0));
|
||
|
|
val &= MPI_CSBASE_BASE_MASK;
|
||
|
|
|
||
|
|
+ /* BT Voyager 2500V has 8 Meg flash in two 4 Meg banks */
|
||
|
|
+ /* Loading from CFE always uses Bank 0 */
|
||
|
|
+ if (!strcmp(board_get_name(), "V2500V_BB")) {
|
||
|
|
+ pr_info("V2500V: Start in Bank 0\n");
|
||
|
|
+ val = val + 0x400000; // Select Bank 0 start address
|
||
|
|
+ }
|
||
|
|
+
|
||
|
|
mtd_resources[0].start = val;
|
||
|
|
mtd_resources[0].end = 0x1FFFFFFF;
|
||
|
|
}
|