ExternalVendorCode/openwrt
1
0
Fork 0
mirror of https://github.com/openwrt/openwrt.git synced 2025-01-10 23:12:48 +00:00
Code Issues Actions 5 Packages Projects Releases Wiki Activity
c143fbc5f1
openwrt/target/linux/bcm63xx/patches-5.4/514-board_bcm6345.patch

40 lines
1.2 KiB
Diff
Raw Normal View History

bcm63xx: copy files to kernel 5.4 Copy config and patches to kernel 5.4. make kernel_oldconfig has been run on 4.19 beforehand. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-04-03 10:26:23 +00:00
--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
bcm63xx: add support for Technicolor TG582n Telecom Italia branded Technicolor TG582n Telecom Italia branded a.k.a. Telecom Italia ADSL2+ Wi-Fi N (AGTWI) has the same PCB as the unbranded Technicolor TG582n with LEDs connected to different GPIO PINs in active low configuration and different LED names. It has a PCB similar to the OpenWrt's ADB P.DG A4001N1 one. Hardware: * Board ID: DANT-V * SoC: Broadcom BCM6328 (rev b0) @ 320MHz, CPU BMIPS4350 * RAM DDR2: 64 Mbyte - EtronTech EM68B16CWQD-25H * Serial flash: 16 Mbyte - Spansion FL 128SAIF00 * Ethernet: 4x Ethernet 10/100 baseT * Wifi 2.4GHz: Broadcom Corporation BCM43227 Wireless Network Adapter (rev 30) * LEDs: 2x Power, 1x ADSL, 2x Internet, 2x Wi-Fi, 2x Service, 4x ethernet * Buttons: 1x Reset, 1x WPS (named WiFi/LED) * UART: 1x TTL 115200n8, VCC GND TX RX, on J3 connector (short R62 and R63) Installation via CFE: * Stock CFE has to be overwritten with a generic 6328 one that can upload .bin images with no signature check (cfe6328_configured.bin) * Connect a serial port to the board * Stop the CFE boot process after power on by pressing enter * Set static IP 192.168.2.10 and subnet mask 255.255.255.0 * Navigate to http://192.168.2.50/ * Upload the OpenWrt image file PCB: |GPIO: |TG582n: |AGTWI: LED2R |488(08) |red Power |red Power LED2G |484(04) |green Power |green Power LED10R |486(06) | |missing R85 end LED LED13G |485(05) |green Ethernet |green ADSL LED11R |494(14) | |red Internet LED14G |491(11) |green Broadband |green Internet LED5R |487(07) |red Internet |red Wi-Fi LED5G |481(01) |green Internet |green Wi-Fi LED12R |498(18) | |red Service LED12G |499(19) | |green Service LED6R |482(02) |red Wi-Fi |missing R108 end LED LED6G |483(03) |green Wi-Fi |missing R107 end LED LED7R |490(10) |red WPS |missing R91 end LED LED7G |489(09) |green WPS |missing R92 end LED LED4 |508(28) |ethernet port 4 |ethernet port 4 LED3 |507(27) |ethernet port 3 |ethernet port 3 LED9 |506(26) |ethernet port 2 |ethernet port 2 LED8 |505(25) |ethernet port 1 |ethernet port 1 SW3 |503(23) |key Reset |key Reset SW5 |504(24) |key WPS |key Wi-Fi/LED SW4 |495(15) |key Wi-Fi |missing R127 end key SW6 |493(13) | |missing R171 end key SW1 |492(12) | |missing R1 end key Signed-off-by: Daniele Castro <danielecastro@hotmail.it> [DT fixes, base-files fixes and device variant] Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-09-08 15:16:06 +00:00
@@ -979,6 +979,19 @@ static struct board_info __initdata boar
bcm63xx: copy files to kernel 5.4 Copy config and patches to kernel 5.4. make kernel_oldconfig has been run on 4.19 beforehand. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-04-03 10:26:23 +00:00
.name = "96345GW2",
.expected_cpu_id = 0x6345,
};
+
bcm63xx: merge RTA770BW and RTA770W board patches The only difference between both boards is the DSL annex. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-08-07 08:30:07 +00:00
+static struct board_info __initdata board_rta770w = {
bcm63xx: refactor board patches Current board patches format is crazy. Let's try to put some order. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-08-07 07:14:15 +00:00
+ .name = "RTA770BW",
+ .expected_cpu_id = 0x6345,
bcm63xx: copy files to kernel 5.4 Copy config and patches to kernel 5.4. make kernel_oldconfig has been run on 4.19 beforehand. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-04-03 10:26:23 +00:00
+
bcm63xx: refactor board patches Current board patches format is crazy. Let's try to put some order. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-08-07 07:14:15 +00:00
+ .has_enet0 = 1,
bcm63xx: copy files to kernel 5.4 Copy config and patches to kernel 5.4. make kernel_oldconfig has been run on 4.19 beforehand. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-04-03 10:26:23 +00:00
+ .enet0 = {
bcm63xx: refactor board patches Current board patches format is crazy. Let's try to put some order. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-08-07 07:14:15 +00:00
+ .has_phy = 1,
+ .phy_id = 0,
+ .force_speed_100 = 1,
+ .force_duplex_full = 1,
bcm63xx: copy files to kernel 5.4 Copy config and patches to kernel 5.4. make kernel_oldconfig has been run on 4.19 beforehand. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-04-03 10:26:23 +00:00
+ },
+};
#endif /* CONFIG_BCM63XX_CPU_6345 */
/*
bcm63xx: add support for Technicolor TG582n Telecom Italia branded Technicolor TG582n Telecom Italia branded a.k.a. Telecom Italia ADSL2+ Wi-Fi N (AGTWI) has the same PCB as the unbranded Technicolor TG582n with LEDs connected to different GPIO PINs in active low configuration and different LED names. It has a PCB similar to the OpenWrt's ADB P.DG A4001N1 one. Hardware: * Board ID: DANT-V * SoC: Broadcom BCM6328 (rev b0) @ 320MHz, CPU BMIPS4350 * RAM DDR2: 64 Mbyte - EtronTech EM68B16CWQD-25H * Serial flash: 16 Mbyte - Spansion FL 128SAIF00 * Ethernet: 4x Ethernet 10/100 baseT * Wifi 2.4GHz: Broadcom Corporation BCM43227 Wireless Network Adapter (rev 30) * LEDs: 2x Power, 1x ADSL, 2x Internet, 2x Wi-Fi, 2x Service, 4x ethernet * Buttons: 1x Reset, 1x WPS (named WiFi/LED) * UART: 1x TTL 115200n8, VCC GND TX RX, on J3 connector (short R62 and R63) Installation via CFE: * Stock CFE has to be overwritten with a generic 6328 one that can upload .bin images with no signature check (cfe6328_configured.bin) * Connect a serial port to the board * Stop the CFE boot process after power on by pressing enter * Set static IP 192.168.2.10 and subnet mask 255.255.255.0 * Navigate to http://192.168.2.50/ * Upload the OpenWrt image file PCB: |GPIO: |TG582n: |AGTWI: LED2R |488(08) |red Power |red Power LED2G |484(04) |green Power |green Power LED10R |486(06) | |missing R85 end LED LED13G |485(05) |green Ethernet |green ADSL LED11R |494(14) | |red Internet LED14G |491(11) |green Broadband |green Internet LED5R |487(07) |red Internet |red Wi-Fi LED5G |481(01) |green Internet |green Wi-Fi LED12R |498(18) | |red Service LED12G |499(19) | |green Service LED6R |482(02) |red Wi-Fi |missing R108 end LED LED6G |483(03) |green Wi-Fi |missing R107 end LED LED7R |490(10) |red WPS |missing R91 end LED LED7G |489(09) |green WPS |missing R92 end LED LED4 |508(28) |ethernet port 4 |ethernet port 4 LED3 |507(27) |ethernet port 3 |ethernet port 3 LED9 |506(26) |ethernet port 2 |ethernet port 2 LED8 |505(25) |ethernet port 1 |ethernet port 1 SW3 |503(23) |key Reset |key Reset SW5 |504(24) |key WPS |key Wi-Fi/LED SW4 |495(15) |key Wi-Fi |missing R127 end key SW6 |493(13) | |missing R171 end key SW1 |492(12) | |missing R1 end key Signed-off-by: Daniele Castro <danielecastro@hotmail.it> [DT fixes, base-files fixes and device variant] Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-09-08 15:16:06 +00:00
@@ -1312,6 +1325,7 @@ static const struct board_info __initcon
bcm63xx: switch to upstream endif comments patch This allows better context for board patches and we no longer need a downstream patch for that. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-08-06 14:12:21 +00:00
#endif /* CONFIG_BCM63XX_CPU_6338 */
bcm63xx: copy files to kernel 5.4 Copy config and patches to kernel 5.4. make kernel_oldconfig has been run on 4.19 beforehand. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-04-03 10:26:23 +00:00
#ifdef CONFIG_BCM63XX_CPU_6345
&board_96345gw2,
bcm63xx: merge RTA770BW and RTA770W board patches The only difference between both boards is the DSL annex. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-08-07 08:30:07 +00:00
+ &board_rta770w,
bcm63xx: switch to upstream endif comments patch This allows better context for board patches and we no longer need a downstream patch for that. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-08-06 14:12:21 +00:00
#endif /* CONFIG_BCM63XX_CPU_6345 */
bcm63xx: copy files to kernel 5.4 Copy config and patches to kernel 5.4. make kernel_oldconfig has been run on 4.19 beforehand. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-04-03 10:26:23 +00:00
#ifdef CONFIG_BCM63XX_CPU_6348
&board_96348r,
bcm63xx: add support for Technicolor TG582n Telecom Italia branded Technicolor TG582n Telecom Italia branded a.k.a. Telecom Italia ADSL2+ Wi-Fi N (AGTWI) has the same PCB as the unbranded Technicolor TG582n with LEDs connected to different GPIO PINs in active low configuration and different LED names. It has a PCB similar to the OpenWrt's ADB P.DG A4001N1 one. Hardware: * Board ID: DANT-V * SoC: Broadcom BCM6328 (rev b0) @ 320MHz, CPU BMIPS4350 * RAM DDR2: 64 Mbyte - EtronTech EM68B16CWQD-25H * Serial flash: 16 Mbyte - Spansion FL 128SAIF00 * Ethernet: 4x Ethernet 10/100 baseT * Wifi 2.4GHz: Broadcom Corporation BCM43227 Wireless Network Adapter (rev 30) * LEDs: 2x Power, 1x ADSL, 2x Internet, 2x Wi-Fi, 2x Service, 4x ethernet * Buttons: 1x Reset, 1x WPS (named WiFi/LED) * UART: 1x TTL 115200n8, VCC GND TX RX, on J3 connector (short R62 and R63) Installation via CFE: * Stock CFE has to be overwritten with a generic 6328 one that can upload .bin images with no signature check (cfe6328_configured.bin) * Connect a serial port to the board * Stop the CFE boot process after power on by pressing enter * Set static IP 192.168.2.10 and subnet mask 255.255.255.0 * Navigate to http://192.168.2.50/ * Upload the OpenWrt image file PCB: |GPIO: |TG582n: |AGTWI: LED2R |488(08) |red Power |red Power LED2G |484(04) |green Power |green Power LED10R |486(06) | |missing R85 end LED LED13G |485(05) |green Ethernet |green ADSL LED11R |494(14) | |red Internet LED14G |491(11) |green Broadband |green Internet LED5R |487(07) |red Internet |red Wi-Fi LED5G |481(01) |green Internet |green Wi-Fi LED12R |498(18) | |red Service LED12G |499(19) | |green Service LED6R |482(02) |red Wi-Fi |missing R108 end LED LED6G |483(03) |green Wi-Fi |missing R107 end LED LED7R |490(10) |red WPS |missing R91 end LED LED7G |489(09) |green WPS |missing R92 end LED LED4 |508(28) |ethernet port 4 |ethernet port 4 LED3 |507(27) |ethernet port 3 |ethernet port 3 LED9 |506(26) |ethernet port 2 |ethernet port 2 LED8 |505(25) |ethernet port 1 |ethernet port 1 SW3 |503(23) |key Reset |key Reset SW5 |504(24) |key WPS |key Wi-Fi/LED SW4 |495(15) |key Wi-Fi |missing R127 end key SW6 |493(13) | |missing R171 end key SW1 |492(12) | |missing R1 end key Signed-off-by: Daniele Castro <danielecastro@hotmail.it> [DT fixes, base-files fixes and device variant] Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-09-08 15:16:06 +00:00
@@ -1368,6 +1382,8 @@ static struct of_device_id const bcm963x
bcm63xx: add missing endif board comnents This provides better context for board patches. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-08-07 09:04:22 +00:00
#endif /* CONFIG_BCM63XX_CPU_6338 */
bcm63xx: copy files to kernel 5.4 Copy config and patches to kernel 5.4. make kernel_oldconfig has been run on 4.19 beforehand. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-04-03 10:26:23 +00:00
#ifdef CONFIG_BCM63XX_CPU_6345
{ .compatible = "brcm,bcm96345gw2", .data = &board_96345gw2, },
bcm63xx: merge RTA770BW and RTA770W board patches The only difference between both boards is the DSL annex. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-08-07 08:30:07 +00:00
+ { .compatible = "dynalink,rta770bw", .data = &board_rta770w, },
+ { .compatible = "dynalink,rta770w", .data = &board_rta770w, },
bcm63xx: add missing endif board comnents This provides better context for board patches. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-08-07 09:04:22 +00:00
#endif /* CONFIG_BCM63XX_CPU_6345 */
bcm63xx: copy files to kernel 5.4 Copy config and patches to kernel 5.4. make kernel_oldconfig has been run on 4.19 beforehand. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-04-03 10:26:23 +00:00
#ifdef CONFIG_BCM63XX_CPU_6348
{ .compatible = "belkin,f5d7633", .data = &board_96348gw_10, },
Reference in New Issue Copy Permalink