mediatek: add support for Netgear WAX206
Specifications:
* SoC: MediaTek MT7622BV
* RAM: DDR3 512 MiB (Nanya NT5CC256M16ER-EK)
* Flash: SPI-NAND 256 MiB (Toshiba TC58CVG1S3HRAIJ)
* Wi-Fi 2.4/5 GHz 4T4R:
* 2.4 GHz: MediaTek MT7622BV
* 5 GHz: MediaTek MT7915AN/MT7975AN
* Ethernet: 4x 10/100/1000 Mbps LAN,
1x 10/100/1000/2500 Mbps WAN (Realtek RTL8221B PHY)
* Switch: MediaTek MT7531AE
* LEDs/Keys: 8/1 (Power, Internet, LAN1, LAN2, LAN3, LAN4,
Wifin and Wifia dual-colour LEDs + Reset pin)
* UART: Marked J19 on board VCC GND TX RX, beginning from "1". 3.3v,
115200n8
* Power: 12 VDC, 2.5 A
Installation:
* Flash the factory image through the stock web interface, or TFTP to
the bootloader. NMRP can be used to TFTP without opening the case.
* U-Boot allows booting an initramfs image via TFTP as follows:
setenv ipaddr 192.168.1.1
setenv serverip 192.168.1.100
tftpboot openwrt-mediatek-mt7622-netgear_wax206-initramfs-recovery.itb
bootm
Known Limitations:
* The 2.5G WAN port labeled 'wan' only works for speeds up to 1G at the
moment. If connected to a multi-gig port the speed has to be manually
set to 1G/full either for the switch port or in OpenWrt. For example
add the following to /etc/rc.local to set it on boot:
/usr/sbin/ethtool -s wan speed 1000 duplex full
Revert to stock firmware:
* Flash the stock firmware to the bootloader using TFTP/NMRP.
References to WAX206 GPL source:
https://www.downloads.netgear.com/files/GPL/WAX206_V1.0.4.0_Source.rar
* openwrt/target/linux/mediatek/dts/mt7622-netgear-wax206.dts
DTS file for this device.
* openwrt/target/linux/mediatek/image/mt7622.mk
Image creation code for this device
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
[fix WAN port (1G only), adjust partition layout, adjust image creation]
Signed-off-by: Thomas Kupper <thomas.kupper@gmail.com>
2022-09-29 20:40:31 +00:00
|
|
|
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
|
|
|
/* Copyright (c) 2022, Marcel Ziswiler <marcel@ziswiler.com> */
|
|
|
|
|
|
|
|
/dts-v1/;
|
|
|
|
#include "mt7622.dtsi"
|
|
|
|
#include "mt6380.dtsi"
|
|
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
|
|
#include <dt-bindings/input/input.h>
|
|
|
|
|
|
|
|
/ {
|
|
|
|
model = "Netgear WAX206";
|
|
|
|
compatible = "netgear,wax206", "mediatek,mt7622";
|
|
|
|
|
|
|
|
aliases {
|
|
|
|
ethernet0 = &gmac0;
|
|
|
|
led-boot = &led_power_r;
|
|
|
|
led-failsafe = &led_power_r;
|
|
|
|
led-running = &led_power_g;
|
|
|
|
led-upgrade = &led_power_g;
|
|
|
|
serial0 = &uart0;
|
|
|
|
};
|
|
|
|
|
|
|
|
chosen {
|
|
|
|
stdout-path = "serial0:115200n8";
|
|
|
|
bootargs = "earlycon=uart8250,mmio32,0x11002000 console=ttyS0,115200n8 swiotlb=512";
|
|
|
|
};
|
|
|
|
|
|
|
|
cpus {
|
|
|
|
cpu@0 {
|
|
|
|
proc-supply = <&mt6380_vcpu_reg>;
|
|
|
|
sram-supply = <&mt6380_vm_reg>;
|
|
|
|
};
|
|
|
|
|
|
|
|
cpu@1 {
|
|
|
|
proc-supply = <&mt6380_vcpu_reg>;
|
|
|
|
sram-supply = <&mt6380_vm_reg>;
|
|
|
|
};
|
|
|
|
};
|
|
|
|
|
|
|
|
gpio-keys {
|
|
|
|
compatible = "gpio-keys";
|
|
|
|
|
|
|
|
reset {
|
|
|
|
gpios = <&pio 0 GPIO_ACTIVE_LOW>;
|
|
|
|
label = "reset";
|
|
|
|
linux,code = <KEY_RESTART>;
|
|
|
|
};
|
|
|
|
|
|
|
|
wps {
|
|
|
|
gpios = <&pio 102 GPIO_ACTIVE_LOW>;
|
|
|
|
label = "wps";
|
|
|
|
linux,code = <KEY_WPS_BUTTON>;
|
|
|
|
};
|
|
|
|
};
|
|
|
|
|
|
|
|
gpio-leds {
|
|
|
|
compatible = "gpio-leds";
|
|
|
|
|
|
|
|
led_power_r: power_red {
|
|
|
|
default-state = "on";
|
|
|
|
gpios = <&pio 3 GPIO_ACTIVE_LOW>;
|
|
|
|
label = "power:red";
|
|
|
|
};
|
|
|
|
|
|
|
|
led_power_g: power_green {
|
|
|
|
default-state = "off";
|
|
|
|
gpios = <&pio 4 GPIO_ACTIVE_LOW>;
|
|
|
|
label = "power:green";
|
|
|
|
};
|
|
|
|
|
|
|
|
inet_green {
|
|
|
|
default-state = "off";
|
|
|
|
gpios = <&pio 20 GPIO_ACTIVE_HIGH>;
|
|
|
|
label = "inet:green";
|
|
|
|
};
|
|
|
|
|
|
|
|
inet_blue {
|
|
|
|
default-state = "off";
|
|
|
|
gpios = <&pio 17 GPIO_ACTIVE_LOW>;
|
|
|
|
label = "inet:blue";
|
|
|
|
};
|
|
|
|
|
|
|
|
wifin_green {
|
|
|
|
default-state = "off";
|
|
|
|
gpios = <&pio 85 GPIO_ACTIVE_LOW>;
|
|
|
|
label = "wifin:green";
|
|
|
|
};
|
|
|
|
|
|
|
|
wifin_blue {
|
|
|
|
default-state = "off";
|
|
|
|
gpios = <&pio 86 GPIO_ACTIVE_LOW>;
|
|
|
|
label = "wifin:blue";
|
|
|
|
};
|
|
|
|
|
|
|
|
wifia_green {
|
|
|
|
default-state = "off";
|
|
|
|
gpios = <&pio 2 GPIO_ACTIVE_HIGH>;
|
|
|
|
label = "wifia:green";
|
|
|
|
};
|
|
|
|
|
|
|
|
wifia_blue {
|
|
|
|
default-state = "off";
|
|
|
|
gpios = <&pio 1 GPIO_ACTIVE_LOW>;
|
|
|
|
label = "wifia:blue";
|
|
|
|
};
|
|
|
|
};
|
|
|
|
|
|
|
|
memory {
|
|
|
|
reg = <0 0x40000000 0 0x40000000>;
|
|
|
|
};
|
|
|
|
};
|
|
|
|
|
|
|
|
&bch {
|
|
|
|
status = "okay";
|
|
|
|
};
|
|
|
|
|
|
|
|
&btif {
|
|
|
|
status = "okay";
|
|
|
|
};
|
|
|
|
|
|
|
|
&cir {
|
|
|
|
pinctrl-names = "default";
|
|
|
|
pinctrl-0 = <&irrx_pins>;
|
|
|
|
status = "okay";
|
|
|
|
};
|
|
|
|
|
|
|
|
ð {
|
|
|
|
pinctrl-names = "default";
|
|
|
|
pinctrl-0 = <ð_pins>;
|
|
|
|
status = "okay";
|
|
|
|
|
|
|
|
gmac0: mac@0 {
|
|
|
|
compatible = "mediatek,eth-mac";
|
|
|
|
nvmem-cells = <&macaddr_factory_7fff4>;
|
|
|
|
nvmem-cell-names = "mac-address";
|
|
|
|
phy-mode = "2500base-x";
|
|
|
|
reg = <0>;
|
|
|
|
|
|
|
|
fixed-link {
|
|
|
|
full-duplex;
|
|
|
|
pause;
|
|
|
|
speed = <2500>;
|
|
|
|
};
|
|
|
|
};
|
|
|
|
|
|
|
|
mdio-bus {
|
|
|
|
#address-cells = <1>;
|
|
|
|
#size-cells = <0>;
|
|
|
|
|
|
|
|
switch@0 {
|
|
|
|
compatible = "mediatek,mt7531";
|
|
|
|
#interrupt-cells = <1>;
|
|
|
|
interrupt-controller;
|
|
|
|
interrupt-parent = <&pio>;
|
|
|
|
interrupts = <53 IRQ_TYPE_LEVEL_HIGH>;
|
|
|
|
reg = <0>;
|
|
|
|
reset-gpios = <&pio 54 GPIO_ACTIVE_HIGH>;
|
|
|
|
|
|
|
|
ports {
|
|
|
|
#address-cells = <1>;
|
|
|
|
#size-cells = <0>;
|
|
|
|
|
|
|
|
port@1 {
|
|
|
|
label = "lan1";
|
|
|
|
reg = <1>;
|
|
|
|
};
|
|
|
|
|
|
|
|
port@2 {
|
|
|
|
label = "lan2";
|
|
|
|
reg = <2>;
|
|
|
|
};
|
|
|
|
|
|
|
|
port@3 {
|
|
|
|
label = "lan3";
|
|
|
|
reg = <3>;
|
|
|
|
};
|
|
|
|
|
|
|
|
port@4 {
|
|
|
|
label = "lan4";
|
|
|
|
reg = <4>;
|
|
|
|
};
|
|
|
|
|
|
|
|
wan: port@5 {
|
|
|
|
label = "wan";
|
|
|
|
nvmem-cells = <&macaddr_factory_7fffa>;
|
|
|
|
nvmem-cell-names = "mac-address";
|
|
|
|
phy-handle = <&rtl8221b_phy>;
|
2023-04-30 03:01:12 +00:00
|
|
|
phy-mode = "2500base-x";
|
mediatek: add support for Netgear WAX206
Specifications:
* SoC: MediaTek MT7622BV
* RAM: DDR3 512 MiB (Nanya NT5CC256M16ER-EK)
* Flash: SPI-NAND 256 MiB (Toshiba TC58CVG1S3HRAIJ)
* Wi-Fi 2.4/5 GHz 4T4R:
* 2.4 GHz: MediaTek MT7622BV
* 5 GHz: MediaTek MT7915AN/MT7975AN
* Ethernet: 4x 10/100/1000 Mbps LAN,
1x 10/100/1000/2500 Mbps WAN (Realtek RTL8221B PHY)
* Switch: MediaTek MT7531AE
* LEDs/Keys: 8/1 (Power, Internet, LAN1, LAN2, LAN3, LAN4,
Wifin and Wifia dual-colour LEDs + Reset pin)
* UART: Marked J19 on board VCC GND TX RX, beginning from "1". 3.3v,
115200n8
* Power: 12 VDC, 2.5 A
Installation:
* Flash the factory image through the stock web interface, or TFTP to
the bootloader. NMRP can be used to TFTP without opening the case.
* U-Boot allows booting an initramfs image via TFTP as follows:
setenv ipaddr 192.168.1.1
setenv serverip 192.168.1.100
tftpboot openwrt-mediatek-mt7622-netgear_wax206-initramfs-recovery.itb
bootm
Known Limitations:
* The 2.5G WAN port labeled 'wan' only works for speeds up to 1G at the
moment. If connected to a multi-gig port the speed has to be manually
set to 1G/full either for the switch port or in OpenWrt. For example
add the following to /etc/rc.local to set it on boot:
/usr/sbin/ethtool -s wan speed 1000 duplex full
Revert to stock firmware:
* Flash the stock firmware to the bootloader using TFTP/NMRP.
References to WAX206 GPL source:
https://www.downloads.netgear.com/files/GPL/WAX206_V1.0.4.0_Source.rar
* openwrt/target/linux/mediatek/dts/mt7622-netgear-wax206.dts
DTS file for this device.
* openwrt/target/linux/mediatek/image/mt7622.mk
Image creation code for this device
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
[fix WAN port (1G only), adjust partition layout, adjust image creation]
Signed-off-by: Thomas Kupper <thomas.kupper@gmail.com>
2022-09-29 20:40:31 +00:00
|
|
|
reg = <5>;
|
|
|
|
};
|
|
|
|
|
|
|
|
port@6 {
|
|
|
|
ethernet = <&gmac0>;
|
|
|
|
phy-mode = "2500base-x";
|
|
|
|
reg = <6>;
|
|
|
|
|
|
|
|
fixed-link {
|
|
|
|
full-duplex;
|
|
|
|
pause;
|
|
|
|
speed = <2500>;
|
|
|
|
};
|
|
|
|
};
|
|
|
|
};
|
|
|
|
};
|
|
|
|
|
|
|
|
rtl8221b_phy: ethernet-phy@7 {
|
2023-04-30 03:01:12 +00:00
|
|
|
compatible = "ethernet-phy-ieee802.3-c45";
|
mediatek: add support for Netgear WAX206
Specifications:
* SoC: MediaTek MT7622BV
* RAM: DDR3 512 MiB (Nanya NT5CC256M16ER-EK)
* Flash: SPI-NAND 256 MiB (Toshiba TC58CVG1S3HRAIJ)
* Wi-Fi 2.4/5 GHz 4T4R:
* 2.4 GHz: MediaTek MT7622BV
* 5 GHz: MediaTek MT7915AN/MT7975AN
* Ethernet: 4x 10/100/1000 Mbps LAN,
1x 10/100/1000/2500 Mbps WAN (Realtek RTL8221B PHY)
* Switch: MediaTek MT7531AE
* LEDs/Keys: 8/1 (Power, Internet, LAN1, LAN2, LAN3, LAN4,
Wifin and Wifia dual-colour LEDs + Reset pin)
* UART: Marked J19 on board VCC GND TX RX, beginning from "1". 3.3v,
115200n8
* Power: 12 VDC, 2.5 A
Installation:
* Flash the factory image through the stock web interface, or TFTP to
the bootloader. NMRP can be used to TFTP without opening the case.
* U-Boot allows booting an initramfs image via TFTP as follows:
setenv ipaddr 192.168.1.1
setenv serverip 192.168.1.100
tftpboot openwrt-mediatek-mt7622-netgear_wax206-initramfs-recovery.itb
bootm
Known Limitations:
* The 2.5G WAN port labeled 'wan' only works for speeds up to 1G at the
moment. If connected to a multi-gig port the speed has to be manually
set to 1G/full either for the switch port or in OpenWrt. For example
add the following to /etc/rc.local to set it on boot:
/usr/sbin/ethtool -s wan speed 1000 duplex full
Revert to stock firmware:
* Flash the stock firmware to the bootloader using TFTP/NMRP.
References to WAX206 GPL source:
https://www.downloads.netgear.com/files/GPL/WAX206_V1.0.4.0_Source.rar
* openwrt/target/linux/mediatek/dts/mt7622-netgear-wax206.dts
DTS file for this device.
* openwrt/target/linux/mediatek/image/mt7622.mk
Image creation code for this device
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
[fix WAN port (1G only), adjust partition layout, adjust image creation]
Signed-off-by: Thomas Kupper <thomas.kupper@gmail.com>
2022-09-29 20:40:31 +00:00
|
|
|
reg = <7>;
|
|
|
|
reset-gpios = <&pio 101 GPIO_ACTIVE_LOW>;
|
|
|
|
interrupts = <52 IRQ_TYPE_LEVEL_HIGH>;
|
|
|
|
reset-assert-us = <100000>;
|
|
|
|
reset-deassert-us = <100000>;
|
|
|
|
};
|
|
|
|
};
|
|
|
|
};
|
|
|
|
|
|
|
|
&pcie0 {
|
|
|
|
pinctrl-names = "default";
|
|
|
|
pinctrl-0 = <&pcie0_pins>;
|
|
|
|
status = "okay";
|
|
|
|
};
|
|
|
|
|
|
|
|
&pcie1 {
|
|
|
|
pinctrl-names = "default";
|
|
|
|
pinctrl-0 = <&pcie1_pins>;
|
|
|
|
status = "okay";
|
|
|
|
};
|
|
|
|
|
|
|
|
&pio {
|
|
|
|
eth_pins: eth-pins {
|
|
|
|
mux {
|
|
|
|
function = "eth";
|
|
|
|
groups = "mdc_mdio", "rgmii_via_gmac2";
|
|
|
|
};
|
|
|
|
};
|
|
|
|
|
|
|
|
irrx_pins: irrx-pins {
|
|
|
|
mux {
|
|
|
|
function = "ir";
|
|
|
|
groups = "ir_1_rx";
|
|
|
|
};
|
|
|
|
};
|
|
|
|
|
|
|
|
irtx_pins: irtx-pins {
|
|
|
|
mux {
|
|
|
|
function = "ir";
|
|
|
|
groups = "ir_1_tx";
|
|
|
|
};
|
|
|
|
};
|
|
|
|
|
|
|
|
pcie0_pins: pcie0-pins {
|
|
|
|
mux {
|
|
|
|
function = "pcie";
|
|
|
|
groups = "pcie0_pad_perst",
|
|
|
|
"pcie0_1_waken",
|
|
|
|
"pcie0_1_clkreq";
|
|
|
|
};
|
|
|
|
};
|
|
|
|
|
|
|
|
pcie1_pins: pcie1-pins {
|
|
|
|
mux {
|
|
|
|
function = "pcie";
|
|
|
|
groups = "pcie1_pad_perst",
|
|
|
|
"pcie1_0_waken",
|
|
|
|
"pcie1_0_clkreq";
|
|
|
|
};
|
|
|
|
};
|
|
|
|
|
|
|
|
pmic_bus_pins: pmic-bus-pins {
|
|
|
|
mux {
|
|
|
|
function = "pmic";
|
|
|
|
groups = "pmic_bus";
|
|
|
|
};
|
|
|
|
};
|
|
|
|
|
|
|
|
pwm7_pins: pwm1-2-pins {
|
|
|
|
mux {
|
|
|
|
function = "pwm";
|
|
|
|
groups = "pwm_ch7_2";
|
|
|
|
};
|
|
|
|
};
|
|
|
|
|
|
|
|
wled_pins: wled-pins {
|
|
|
|
mux {
|
|
|
|
function = "led";
|
|
|
|
groups = "wled";
|
|
|
|
};
|
|
|
|
};
|
|
|
|
|
|
|
|
/* Serial NAND is shared pin with SPI-NOR */
|
|
|
|
serial_nand_pins: serial-nand-pins {
|
|
|
|
mux {
|
|
|
|
function = "flash";
|
|
|
|
groups = "snfi";
|
|
|
|
};
|
|
|
|
};
|
|
|
|
|
|
|
|
spic0_pins: spic0-pins {
|
|
|
|
mux {
|
|
|
|
function = "spi";
|
|
|
|
groups = "spic0_0";
|
|
|
|
};
|
|
|
|
};
|
|
|
|
|
|
|
|
spic1_pins: spic1-pins {
|
|
|
|
mux {
|
|
|
|
function = "spi";
|
|
|
|
groups = "spic1_0";
|
|
|
|
};
|
|
|
|
};
|
|
|
|
|
|
|
|
uart0_pins: uart0-pins {
|
|
|
|
mux {
|
|
|
|
function = "uart";
|
|
|
|
groups = "uart0_0_tx_rx";
|
|
|
|
};
|
|
|
|
};
|
|
|
|
|
|
|
|
uart2_pins: uart2-pins {
|
|
|
|
mux {
|
|
|
|
function = "uart";
|
|
|
|
groups = "uart2_1_tx_rx";
|
|
|
|
};
|
|
|
|
};
|
|
|
|
|
|
|
|
watchdog_pins: watchdog-pins {
|
|
|
|
mux {
|
|
|
|
function = "watchdog";
|
|
|
|
groups = "watchdog";
|
|
|
|
};
|
|
|
|
};
|
|
|
|
};
|
|
|
|
|
|
|
|
&pwm {
|
|
|
|
pinctrl-names = "default";
|
|
|
|
pinctrl-0 = <&pwm7_pins>;
|
|
|
|
status = "okay";
|
|
|
|
};
|
|
|
|
|
|
|
|
&pwrap {
|
|
|
|
pinctrl-names = "default";
|
|
|
|
pinctrl-0 = <&pmic_bus_pins>;
|
|
|
|
status = "okay";
|
|
|
|
};
|
|
|
|
|
|
|
|
&rtc {
|
|
|
|
status = "disabled";
|
|
|
|
};
|
|
|
|
|
|
|
|
&sata {
|
|
|
|
status = "disabled";
|
|
|
|
};
|
|
|
|
|
|
|
|
&sata_phy {
|
|
|
|
status = "disabled";
|
|
|
|
};
|
|
|
|
|
|
|
|
&slot0 {
|
|
|
|
wmac1: mt7915@0,0 {
|
|
|
|
reg = <0x0000 0 0 0 0>;
|
|
|
|
ieee80211-freq-limit = <5000000 6000000>;
|
|
|
|
};
|
|
|
|
};
|
|
|
|
|
|
|
|
&snfi {
|
|
|
|
pinctrl-names = "default";
|
|
|
|
pinctrl-0 = <&serial_nand_pins>;
|
|
|
|
status = "okay";
|
|
|
|
|
|
|
|
snand: flash@0 {
|
|
|
|
compatible = "spi-nand";
|
|
|
|
mediatek,bmt-table-size = <0x1000>;
|
|
|
|
mediatek,bmt-v2;
|
|
|
|
nand-ecc-engine = <&snfi>;
|
|
|
|
reg = <0>;
|
|
|
|
spi-rx-bus-width = <4>;
|
|
|
|
spi-tx-bus-width = <4>;
|
|
|
|
|
|
|
|
partitions {
|
|
|
|
compatible = "fixed-partitions";
|
|
|
|
#address-cells = <1>;
|
|
|
|
#size-cells = <1>;
|
|
|
|
|
|
|
|
partition@0 {
|
|
|
|
label = "Preloader";
|
|
|
|
reg = <0x00000 0x0080000>;
|
|
|
|
read-only;
|
|
|
|
};
|
|
|
|
|
|
|
|
partition@80000 {
|
|
|
|
label = "ATF";
|
|
|
|
reg = <0x80000 0x0040000>;
|
|
|
|
read-only;
|
|
|
|
};
|
|
|
|
|
|
|
|
partition@c0000 {
|
|
|
|
label = "Bootloader";
|
|
|
|
reg = <0xc0000 0x0080000>;
|
|
|
|
read-only;
|
|
|
|
};
|
|
|
|
|
|
|
|
partition@140000 {
|
|
|
|
label = "Config";
|
|
|
|
reg = <0x140000 0x0080000>;
|
|
|
|
};
|
|
|
|
|
|
|
|
factory: partition@1c0000 {
|
|
|
|
compatible = "nvmem-cells";
|
|
|
|
label = "Factory";
|
|
|
|
reg = <0x1c0000 0x0100000>;
|
|
|
|
#address-cells = <1>;
|
|
|
|
#size-cells = <1>;
|
|
|
|
read-only;
|
|
|
|
|
|
|
|
macaddr_factory_7fff4: macaddr@7fff4 {
|
|
|
|
reg = <0x7fff4 0x6>;
|
|
|
|
};
|
|
|
|
|
|
|
|
macaddr_factory_7fffa: macaddr@7fffa {
|
|
|
|
reg = <0x7fffa 0x6>;
|
|
|
|
};
|
|
|
|
};
|
|
|
|
|
|
|
|
partition@2c0000 {
|
|
|
|
label = "firmware";
|
|
|
|
reg = <0x2c0000 0x2600000>;
|
|
|
|
|
|
|
|
compatible = "fixed-partitions";
|
|
|
|
#address-cells = <1>;
|
|
|
|
#size-cells = <1>;
|
|
|
|
|
|
|
|
partition@0 {
|
|
|
|
label = "kernel";
|
|
|
|
reg = <0x0 0x600000>;
|
|
|
|
};
|
|
|
|
|
|
|
|
partition@600000 {
|
|
|
|
label = "ubi";
|
|
|
|
reg = <0x600000 0x2000000>;
|
|
|
|
};
|
|
|
|
};
|
|
|
|
|
|
|
|
partition@28c0000 {
|
|
|
|
label = "firmware_backup";
|
|
|
|
reg = <0x28c0000 0x2600000>;
|
|
|
|
read-only;
|
|
|
|
};
|
|
|
|
|
|
|
|
partition@4ec0000 {
|
|
|
|
label = "CFG";
|
|
|
|
reg = <0x4ec0000 0x800000>;
|
|
|
|
read-only;
|
|
|
|
};
|
|
|
|
|
|
|
|
partition@56c0000 {
|
|
|
|
label = "RAE";
|
|
|
|
reg = <0x56c0000 0x400000>;
|
|
|
|
read-only;
|
|
|
|
};
|
|
|
|
|
|
|
|
partition@5ac0000 {
|
|
|
|
label = "POT";
|
|
|
|
reg = <0x5ac0000 0x100000>;
|
|
|
|
read-only;
|
|
|
|
};
|
|
|
|
|
|
|
|
partition@5bc0000 {
|
|
|
|
label = "Language";
|
|
|
|
reg = <0x5bc0000 0x400000>;
|
|
|
|
read-only;
|
|
|
|
};
|
|
|
|
|
|
|
|
partition@5fc0000 {
|
|
|
|
label = "Traffic";
|
|
|
|
reg = <0x5fc0000 0x200000>;
|
|
|
|
read-only;
|
|
|
|
};
|
|
|
|
|
|
|
|
partition@61c0000 {
|
|
|
|
label = "Cert";
|
|
|
|
reg = <0x61c0000 0x100000>;
|
|
|
|
read-only;
|
|
|
|
};
|
|
|
|
|
|
|
|
partition@62c0000 {
|
|
|
|
label = "NTGRcryptK";
|
|
|
|
reg = <0x62c0000 0x100000>;
|
|
|
|
read-only;
|
|
|
|
};
|
|
|
|
|
|
|
|
partition@63c0000 {
|
|
|
|
label = "NTGRcryptD";
|
|
|
|
reg = <0x63c0000 0x500000>;
|
|
|
|
read-only;
|
|
|
|
};
|
|
|
|
|
|
|
|
partition@68c0000 {
|
|
|
|
label = "LOG";
|
|
|
|
reg = <0x68c0000 0x100000>;
|
|
|
|
read-only;
|
|
|
|
};
|
|
|
|
|
|
|
|
partition@69c0000 {
|
|
|
|
label = "User_data";
|
|
|
|
reg = <0x69c0000 0x640000>;
|
|
|
|
read-only;
|
|
|
|
};
|
|
|
|
|
|
|
|
};
|
|
|
|
};
|
|
|
|
};
|
|
|
|
|
|
|
|
&spi0 {
|
|
|
|
pinctrl-names = "default";
|
|
|
|
pinctrl-0 = <&spic0_pins>;
|
|
|
|
status = "okay";
|
|
|
|
};
|
|
|
|
|
|
|
|
&spi1 {
|
|
|
|
pinctrl-names = "default";
|
|
|
|
pinctrl-0 = <&spic1_pins>;
|
|
|
|
status = "okay";
|
|
|
|
};
|
|
|
|
|
|
|
|
&ssusb {
|
|
|
|
status = "disabled";
|
|
|
|
};
|
|
|
|
|
|
|
|
&u3phy {
|
|
|
|
status = "disabled";
|
|
|
|
};
|
|
|
|
|
|
|
|
&uart0 {
|
|
|
|
pinctrl-names = "default";
|
|
|
|
pinctrl-0 = <&uart0_pins>;
|
|
|
|
status = "okay";
|
|
|
|
};
|
|
|
|
|
|
|
|
&uart2 {
|
|
|
|
pinctrl-names = "default";
|
|
|
|
pinctrl-0 = <&uart2_pins>;
|
|
|
|
status = "okay";
|
|
|
|
};
|
|
|
|
|
|
|
|
&watchdog {
|
|
|
|
pinctrl-names = "default";
|
|
|
|
pinctrl-0 = <&watchdog_pins>;
|
|
|
|
status = "okay";
|
|
|
|
};
|
|
|
|
|
|
|
|
&wmac {
|
|
|
|
mediatek,mtd-eeprom = <&factory 0x0000>;
|
|
|
|
status = "okay";
|
|
|
|
};
|
|
|
|
|
|
|
|
&wmac1 {
|
|
|
|
mediatek,mtd-eeprom = <&factory 0x05000>;
|
|
|
|
};
|