2019-09-04 17:01:23 +00:00
|
|
|
From b52d193fe45231f55ba041a890f00925caf2d976 Mon Sep 17 00:00:00 2001
|
2019-07-09 18:32:28 +00:00
|
|
|
From: Matthias Reichl <hias@horus.com>
|
|
|
|
|
Date: Wed, 9 Jan 2019 14:51:01 +0100
|
2019-09-04 17:01:23 +00:00
|
|
|
Subject: [PATCH 291/782] gpio-ir: change default pull configuration to up
|
2019-07-09 18:32:28 +00:00
|
|
|
|
|
|
|
|
IR receivers like the TSOP series from Vishay and compatible ones
|
|
|
|
|
have active-low open collector outputs with an internal pull up of
|
|
|
|
|
about 30k (according to the TSOP datasheets).
|
|
|
|
|
|
|
|
|
|
Activating a pull-down resistor on the GPIO will make it work against
|
|
|
|
|
the pull-up in the IR receiver and brings the idle input voltage down
|
|
|
|
|
to about 1.9V (measured on a RPi3B+ with a TSOP4438). While that's
|
|
|
|
|
usually enough to make the RPi see a high signal it's certainly not
|
|
|
|
|
optimal and may even fail when using an IR receiver with a weaker pull-up.
|
|
|
|
|
|
|
|
|
|
Switching the default GPIO pull to "up" results in an input voltage
|
|
|
|
|
level of about 3.3V and ensures that an idle state (high signal) will
|
|
|
|
|
be detected if no IR receiver is attached.
|
|
|
|
|
|
|
|
|
|
Signed-off-by: Matthias Reichl <hias@horus.com>
|
|
|
|
|
---
|
|
|
|
|
arch/arm/boot/dts/overlays/README | 2 +-
|
|
|
|
|
arch/arm/boot/dts/overlays/gpio-ir-overlay.dts | 2 +-
|
|
|
|
|
2 files changed, 2 insertions(+), 2 deletions(-)
|
|
|
|
|
|
|
|
|
|
--- a/arch/arm/boot/dts/overlays/README
|
|
|
|
|
+++ b/arch/arm/boot/dts/overlays/README
|
|
|
|
|
@@ -611,7 +611,7 @@ Load: dtoverlay=gpio-ir,<param>=<val>
|
|
|
|
|
Params: gpio_pin Input pin number. Default is 18.
|
|
|
|
|
|
|
|
|
|
gpio_pull Desired pull-up/down state (off, down, up)
|
|
|
|
|
- Default is "down".
|
|
|
|
|
+ Default is "up".
|
|
|
|
|
|
|
|
|
|
rc-map-name Default rc keymap (can also be changed by
|
|
|
|
|
ir-keytable), defaults to "rc-rc6-mce"
|
|
|
|
|
--- a/arch/arm/boot/dts/overlays/gpio-ir-overlay.dts
|
|
|
|
|
+++ b/arch/arm/boot/dts/overlays/gpio-ir-overlay.dts
|
|
|
|
|
@@ -30,7 +30,7 @@
|
|
|
|
|
gpio_ir_pins: gpio_ir_pins@12 {
|
|
|
|
|
brcm,pins = <18>; // pin 18
|
|
|
|
|
brcm,function = <0>; // in
|
|
|
|
|
- brcm,pull = <1>; // down
|
|
|
|
|
+ brcm,pull = <2>; // up
|
|
|
|
|
};
|
|
|
|
|
};
|
|
|
|
|
};
|
