2018-02-21 19:40:50 +00:00
|
|
|
include $(TOPDIR)/rules.mk
|
|
|
|
|
include $(INCLUDE_DIR)/image.mk
|
|
|
|
|
|
ipq40xx: add support for the ZyXEL NBG6617
This patch adds support for ZyXEL NBG6617
Hardware highlights:
SOC: IPQ4018 / QCA Dakota
CPU: Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7
DRAM: 256 MiB DDR3L-1600/1866 Nanya NT5CC128M16IP-DI @ 537 MHz
NOR: 32 MiB Macronix MX25L25635F
ETH: Qualcomm Atheros QCA8075 Gigabit Switch (4 x LAN, 1 x WAN)
USB: 1 x 3.0 (via Synopsys DesignWare DWC3 controller in the SoC)
WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2
WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2
INPUT: RESET Button, WIFI/Rfkill Togglebutton, WPS Button
LEDS: Power, WAN, LAN 1-4, WLAN 2.4GHz, WLAN 5GHz, USB, WPS
Serial:
WARNING: The serial port needs a TTL/RS-232 3.3v level converter!
The Serial setting is 115200-8-N-1. The 1x4 .1" header comes
pre-soldered. Pinout:
1. 3v3 (Label printed on the PCB), 2. RX, 3. GND, 4. TX
first install / debricking / restore stock:
0. Have a PC running a tftp-server @ 192.168.1.99/24
1. connect the PC to any LAN-Ports
2. put the openwrt...-factory.bin (or V1.00(ABCT.X).bin for stock) file
into the tftp-server root directory and rename it to just "ras.bin".
3. power-cycle the router and hold down the the WPS button (for 30sek)
4. Wait (for a long time - the serial console provides some progress
reports. The u-boot says it best: "Please be patient".
5. Once the power LED starts to flashes slowly and the USB + WPS LEDs
flashes fast at the same time. You have to reboot the device and
it should then come right up.
Installation via Web-UI:
0. Connect a PC to the powered-on router. It will assign your PC a
IP-address via DHCP
1. Access the Web-UI at 192.168.1.1 (Default Passwort: 1234)
2. Go to the "Expert Mode"
3. Under "Maintenance", select "Firmware-Upgrade"
4. Upload the OpenWRT factory image
5. Wait for the Device to finish.
It will reboot into OpenWRT without any additional actions needed.
To open the ZyXEL NBG6617:
0. remove the four rubber feet glued on the backside
1. remove the four philips screws and pry open the top cover
(by applying force between the plastic top housing from the
backside/lan-port side)
Access the real u-boot shell:
ZyXEL uses a proprietary loader/shell on top of u-boot: "ZyXEL zloader v2.02"
When the device is starting up, the user can enter the the loader shell
by simply pressing a key within the 3 seconds once the following string
appears on the serial console:
| Hit any key to stop autoboot: 3
The user is then dropped to a locked shell.
|NBG6617> HELP
|ATEN x[,y] set BootExtension Debug Flag (y=password)
|ATSE x show the seed of password generator
|ATSH dump manufacturer related data in ROM
|ATRT [x,y,z,u] RAM read/write test (x=level, y=start addr, z=end addr, u=iterations)
|ATGO boot up whole system
|ATUR x upgrade RAS image (filename)
|NBG6617>
In order to escape/unlock a password challenge has to be passed.
Note: the value is dynamic! you have to calculate your own!
First use ATSE $MODELNAME (MODELNAME is the hostname in u-boot env)
to get the challange value/seed.
|NBG6617> ATSE NBG6617
|012345678901
This seed/value can be converted to the password with the help of this
bash script (Thanks to http://www.adslayuda.com/Zyxel650-9.html authors):
- tool.sh -
ror32() {
echo $(( ($1 >> $2) | (($1 << (32 - $2) & (2**32-1)) ) ))
}
v="0x$1"
a="0x${v:2:6}"
b=$(( $a + 0x10F0A563))
c=$(( 0x${v:12:14} & 7 ))
p=$(( $(ror32 $b $c) ^ $a ))
printf "ATEN 1,%X\n" $p
- end of tool.sh -
|# bash ./tool.sh 012345678901
|
|ATEN 1,879C711
copy and paste the result into the shell to unlock zloader.
|NBG6617> ATEN 1,0046B0017430
If the entered code was correct the shell will change to
use the ATGU command to enter the real u-boot shell.
|NBG6617> ATGU
|NBG6617#
Co-authored-by: David Bauer <mail@david-bauer.net>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: David Bauer <mail@david-bauer.net>
2018-06-21 12:24:59 +00:00
|
|
|
DEVICE_VARS += RAS_BOARD RAS_ROOTFS_SIZE RAS_VERSION
|
|
|
|
|
|
2018-02-21 19:40:50 +00:00
|
|
|
define Device/Default
|
|
|
|
|
PROFILES := Default
|
|
|
|
|
KERNEL_DEPENDS = $$(wildcard $(DTS_DIR)/$$(DEVICE_DTS).dts)
|
|
|
|
|
KERNEL_INITRAMFS_PREFIX := $$(IMG_PREFIX)-$(1)-initramfs
|
|
|
|
|
KERNEL_PREFIX := $$(IMAGE_PREFIX)
|
|
|
|
|
KERNEL_LOADADDR := 0x80208000
|
|
|
|
|
SUPPORTED_DEVICES := $(subst _,$(comma),$(1))
|
|
|
|
|
IMAGE/sysupgrade.bin = sysupgrade-tar | append-metadata
|
|
|
|
|
IMAGE/sysupgrade.bin/squashfs :=
|
|
|
|
|
endef
|
|
|
|
|
|
|
|
|
|
define Device/FitImage
|
|
|
|
|
KERNEL_SUFFIX := -fit-uImage.itb
|
|
|
|
|
KERNEL = kernel-bin | gzip | fit gzip $$(DTS_DIR)/$$(DEVICE_DTS).dtb
|
|
|
|
|
KERNEL_NAME := Image
|
|
|
|
|
endef
|
|
|
|
|
|
|
|
|
|
define Device/FitImageLzma
|
|
|
|
|
KERNEL_SUFFIX := -fit-uImage.itb
|
|
|
|
|
KERNEL = kernel-bin | lzma | fit lzma $$(DTS_DIR)/$$(DEVICE_DTS).dtb
|
|
|
|
|
KERNEL_NAME := Image
|
|
|
|
|
endef
|
|
|
|
|
|
2019-01-24 03:20:55 +00:00
|
|
|
define Device/FitzImage
|
|
|
|
|
KERNEL_SUFFIX := -fit-zImage.itb
|
|
|
|
|
KERNEL = kernel-bin | fit none $$(DTS_DIR)/$$(DEVICE_DTS).dtb
|
|
|
|
|
KERNEL_NAME := zImage
|
|
|
|
|
endef
|
|
|
|
|
|
2018-02-21 19:40:50 +00:00
|
|
|
define Device/UbiFit
|
|
|
|
|
KERNEL_IN_UBI := 1
|
|
|
|
|
IMAGES := nand-factory.ubi nand-sysupgrade.bin
|
|
|
|
|
IMAGE/nand-factory.ubi := append-ubi
|
|
|
|
|
IMAGE/nand-sysupgrade.bin := sysupgrade-tar | append-metadata
|
|
|
|
|
endef
|
|
|
|
|
|
ipq40xx: add support for Netgear EX6100v2/EX6150v2
Specifications:
SOC: Qualcomm IPQ4018 (DAKOTA) ARM Quad-Core
RAM: 256 MB Winbond W632GU6KB12J
FLASH: 16 MiB Macronix MX25L12805D
ETH: Qualcomm QCA8072
WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11b/g/n/ac 2x2
WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11n/ac
1x1 (EX6100)
2x2 (EX6150)
INPUT: Power, WPS, reset button
AP / Range-extender toggle
LED: Power, Router, Extender (dual), WPS, Left-/Right-arrow
SERIAL: Header next to QCA8072 chip.
VCC, TX, RX, GND (Square hole is VCC)
WARNING: The serial port needs a TTL/RS-232 v3.3 level converter!
The Serial setting is 115200-8-N-1.
Tested and working:
- Ethernet
- 2.4 GHz WiFi (Correct MAC-address)
- 5 GHz WiFi (Correct MAC-address)
- Factory installation from WebIF
- Factory installation from tftp
- OpenWRT sysupgrade (Preserving and non-preserving)
- LEDs
- Buttons
Not Working:
- AP/Extender toggle-switch
Untested:
- Support on EX6100v2. They share the same GPL-Code and vendor-images.
The 6100v2 seems to lack one 5GHz stream and differs in the 5GHz
board-blob. I only own a EX6150v2, therefore i am only able to verify
functionality on this device.
Install via Web-Interface:
Upload the factory image to the device to the Netgear Web-Interface.
The device might asks you to confirm the update a second time due to
detecting the OpenWRT firmware as older. The device will automatically
reboot after the image is written to flash.
Install via TFTP:
Connect to the devices serial. Hit Enter-Key in bootloader to stop
autobooting. Command "fw_recovery" will start a tftp server, waiting for
a DNI image to be pushed.
Assign your computer the IP-address 192.168.1.10/24. Push image with
tftp -4 -v -m binary 192.168.1.1 -c put <OPENWRT_FACTORY>
Device will erase factory-partition first, then writes the pushed image
to flash and reboots.
Parts of this commit are based on Thomas Hebb's work on the
openwrt-devel mailinglist.
See https://lists.openwrt.org/pipermail/openwrt-devel/2018-January/043418.html
Signed-off-by: David Bauer <mail@david-bauer.net>
2018-03-28 22:32:38 +00:00
|
|
|
define Device/DniImage
|
|
|
|
|
KERNEL_SUFFIX := -fit-uImage.itb
|
|
|
|
|
KERNEL = kernel-bin | gzip | fit gzip $$(DTS_DIR)/$$(DEVICE_DTS).dtb
|
|
|
|
|
KERNEL_NAME := Image
|
|
|
|
|
NETGEAR_BOARD_ID :=
|
|
|
|
|
NETGEAR_HW_ID :=
|
|
|
|
|
IMAGES := factory.img sysupgrade.bin
|
2018-12-20 21:55:13 +00:00
|
|
|
IMAGE/factory.img := append-kernel | pad-offset 64k 64 | append-uImage-fakehdr filesystem | append-rootfs | pad-rootfs | netgear-dni
|
|
|
|
|
IMAGE/sysupgrade.bin := append-kernel | pad-offset 64k 64 | append-uImage-fakehdr filesystem | append-rootfs | pad-rootfs | append-metadata
|
ipq40xx: add support for Netgear EX6100v2/EX6150v2
Specifications:
SOC: Qualcomm IPQ4018 (DAKOTA) ARM Quad-Core
RAM: 256 MB Winbond W632GU6KB12J
FLASH: 16 MiB Macronix MX25L12805D
ETH: Qualcomm QCA8072
WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11b/g/n/ac 2x2
WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11n/ac
1x1 (EX6100)
2x2 (EX6150)
INPUT: Power, WPS, reset button
AP / Range-extender toggle
LED: Power, Router, Extender (dual), WPS, Left-/Right-arrow
SERIAL: Header next to QCA8072 chip.
VCC, TX, RX, GND (Square hole is VCC)
WARNING: The serial port needs a TTL/RS-232 v3.3 level converter!
The Serial setting is 115200-8-N-1.
Tested and working:
- Ethernet
- 2.4 GHz WiFi (Correct MAC-address)
- 5 GHz WiFi (Correct MAC-address)
- Factory installation from WebIF
- Factory installation from tftp
- OpenWRT sysupgrade (Preserving and non-preserving)
- LEDs
- Buttons
Not Working:
- AP/Extender toggle-switch
Untested:
- Support on EX6100v2. They share the same GPL-Code and vendor-images.
The 6100v2 seems to lack one 5GHz stream and differs in the 5GHz
board-blob. I only own a EX6150v2, therefore i am only able to verify
functionality on this device.
Install via Web-Interface:
Upload the factory image to the device to the Netgear Web-Interface.
The device might asks you to confirm the update a second time due to
detecting the OpenWRT firmware as older. The device will automatically
reboot after the image is written to flash.
Install via TFTP:
Connect to the devices serial. Hit Enter-Key in bootloader to stop
autobooting. Command "fw_recovery" will start a tftp server, waiting for
a DNI image to be pushed.
Assign your computer the IP-address 192.168.1.10/24. Push image with
tftp -4 -v -m binary 192.168.1.1 -c put <OPENWRT_FACTORY>
Device will erase factory-partition first, then writes the pushed image
to flash and reboots.
Parts of this commit are based on Thomas Hebb's work on the
openwrt-devel mailinglist.
See https://lists.openwrt.org/pipermail/openwrt-devel/2018-January/043418.html
Signed-off-by: David Bauer <mail@david-bauer.net>
2018-03-28 22:32:38 +00:00
|
|
|
endef
|
|
|
|
|
DEVICE_VARS += NETGEAR_BOARD_ID NETGEAR_HW_ID
|
|
|
|
|
|
ipq40xx: add factory image for EnGenius ENS620EXT
Extended mksenaofw to support new "capwap" header structure.
This supports flashing from factory 3.0.0, 3.0.1, 3.1.0 and 3.5.5
firmware.
Note that the factory image format changes for 3.1 and later firmware,
and that the 3.1.0 and 3.5.5 Engenius firmware will refuse the
factory_30.bin file. Similarly, the 3.0.0 and 3.0.1 Engenius firmware
will refuse the factory_35.bin file.
Flashing from the Engenius 3.1.0 firmware with the factory_35.bin
firmware has not been tested, as 3.1.0 firmware (Engenius "middleFW")
is only intended as part of the upgrade path to 3.5.5 firmware.
Modified ipq40xx image Makefile to appropriately invoke mksenaofw
with new parameters to configure the capwap header.
Note that there is currently no method to return to factory firmware,
so this is a one-way street.
Path from factory 3.0.0 and 3.0.1 (EnGenius) software to OpenWrt is
to navigate to 192.168.1.1 on the stock firmware and navigate to the
firmware menu. Then copy the URL you have for that page, something like
http://192.168.1.1/cgi-bin/luci/;stok=12345abcdef/admin/system/flashops
and replace the trailing /admin/system/flashops with just /easyflashops
You should then be presented with a simple "Firmware Upgrade" page.
On that page, BE SURE TO CLEAR the "Keep Settings:" checkbox.
Choose the openwrt-ipq40xx-engenius_ens620ext-squashfs-factory_30.bin,
click "Upgrade" and on the following page select "Proceed".
Path from factory 3.5.5 (EnGenius) software to OpenWrt is simply to
use the stock firmware update menu. Choose the
openwrt-ipq40xx-engenius_ens620ext-squashfs-factory_35.bin and click
"Upload" and "Proceed".
The device should then flash the OpenWrt firmware and reboot. Note
that this resets the device to a default configuration with Wi-Fi
disabled, LAN1/PoE acting as a WAN port (running DHCP client) and LAN2
acting as a LAN port with a DHCP server on 192.168.1.x (AP is at
192.168.1.1)
Signed-off-by: Steve Glennon <s.glennon@cablelabs.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[sorry, for unfixing the 80-lines eyesores.]
2019-04-09 20:46:32 +00:00
|
|
|
define Build/SenaoFW
|
|
|
|
|
-$(STAGING_DIR_HOST)/bin/mksenaofw \
|
|
|
|
|
-n $(BOARD_NAME) -r $(VENDOR_ID) -p $(1) \
|
|
|
|
|
-c $(DATECODE) -w $(2) -x $(CW_VER) -t 0 \
|
|
|
|
|
-e $@ \
|
|
|
|
|
-o $@.new
|
|
|
|
|
@cp $@.new $@
|
|
|
|
|
endef
|
ipq40xx: add support for ASUS RT-AC58U/RT-ACRH13
This patch adds support for ASUS RT-AC58U/RT-ACRH13.
hardware highlights:
SOC: IPQ4018 / QCA Dakota
CPU: Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7
DRAM: 128 MiB DDR3L-1066 @ 537 MHz (1074?) NT5CC64M16GP-DI
NOR: 2 MiB Macronix MX25L1606E (for boot, QSEE)
NAND: 128 MiB Winbond W25NO1GVZE1G (cal + kernel + root, UBI)
ETH: Qualcomm Atheros QCA8075 Gigabit Switch (4 x LAN, 1 x WAN)
USB: 1 x 3.0 (via Synopsys DesignWare DWC3 controller in the SoC)
WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2
WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2
INPUT: one Reset and one WPS button
LEDS: Status, WAN, WIFI1/2, USB and LAN (one blue LED for each)
Serial:
WARNING: The serial port needs a TTL/RS-232 3V3 level converter!
The Serial setting is 115200-8-N-1. The board has an unpopulated
1x4 0.1" header. The pinout (VDD, RX, GND, TX) is printed on the
PCB right next to the connector.
U-Boot Note: The ethernet driver isn't always reliable and can sometime
time out... Don't worry, just retry.
Access via the serial console is required. As well as a working
TFTP-server setup and the initramfs image. (If not provided, it
has to be built from the OpenWrt source. Make sure to enable
LZMA as the compression for the INITRAMFS!)
To install the image permanently, you have to do the following
steps in the listed order.
1. Open up the router.
There are four phillips screws hiding behind the four plastic
feets on the underside.
2. Connect the serial cable (See notes above)
3. Connect your router via one of the four LAN-ports (yellow)
to a PC which can set the IP-Address and ssh and scp from.
If possible set your PC's IPv4 Address to 192.168.1.70
(As this is the IP-Address the Router's bootloader expects
for the tftp server)
4. power up the router and enter the u-boot
choose option 1 to upload the initramfs image. And follow
through the ipv4 setup.
Wait for your router's status LED to stop blinking rapidly and
glow just blue. (The LAN LED should also be glowing blue).
3. Connect to the OpenWrt running in RAM
The default IPv4-Address of your router will be 192.168.1.1.
1. Copy over the openwrt-sysupgrade.bin image to your router's
temporary directory
# scp openwrt-sysupgrade.bin root@192.168.1.1:/tmp
2. ssh from your PC into your router as root.
# ssh root@192.168.1.1
The default OpenWrt-Image won't ask for a password. Simply hit the Enter-Key.
Once connected...: run the following commands on your temporary installation
3. delete the "jffs2" ubi partition to make room for your new root partition
# ubirmvol /dev/ubi0 --name=jffs2
4. install OpenWrt on the NAND Flash.
# sysupgrade -v /tmp/openwrt-sysupgrade.bin
- This will will automatically reboot the router -
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-03-07 08:13:10 +00:00
|
|
|
|
2018-04-11 09:14:36 +00:00
|
|
|
define Device/8dev_jalapeno
|
|
|
|
|
$(call Device/FitImage)
|
|
|
|
|
$(call Device/UbiFit)
|
|
|
|
|
DEVICE_DTS := qcom-ipq4018-jalapeno
|
|
|
|
|
BLOCKSIZE := 128k
|
|
|
|
|
PAGESIZE := 2048
|
|
|
|
|
DEVICE_TITLE := 8devices Jalapeno
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += 8dev_jalapeno
|
|
|
|
|
|
2019-01-29 17:12:51 +00:00
|
|
|
define Device/alfa-network_ap120c-ac
|
|
|
|
|
$(call Device/FitImage)
|
|
|
|
|
$(call Device/UbiFit)
|
|
|
|
|
DEVICE_TITLE := ALFA Network AP120C-AC
|
|
|
|
|
DEVICE_DTS := qcom-ipq4018-ap120c-ac
|
|
|
|
|
DEVICE_PACKAGES := ipq-wifi-alfa-network_ap120c-ac kmod-usb-acm \
|
|
|
|
|
kmod-tpm-i2c-atmel uboot-envtools
|
|
|
|
|
BLOCKSIZE := 128k
|
|
|
|
|
PAGESIZE := 2048
|
|
|
|
|
IMAGE_SIZE := 65536k
|
|
|
|
|
IMAGES := nand-factory.bin nand-sysupgrade.bin
|
|
|
|
|
IMAGE/nand-factory.bin := append-ubi | qsdk-ipq-factory-nand
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += alfa-network_ap120c-ac
|
|
|
|
|
|
2019-02-12 16:19:51 +00:00
|
|
|
define Device/asus_map-ac2200
|
|
|
|
|
$(call Device/FitImageLzma)
|
|
|
|
|
DEVICE_DTS := qcom-ipq4019-map-ac2200
|
|
|
|
|
DEVICE_TITLE := ASUS Lyra MAP-AC2200
|
|
|
|
|
IMAGES := sysupgrade.bin
|
|
|
|
|
DEVICE_PACKAGES := ipq-wifi-asus_map-ac2200 ath10k-firmware-qca9888-ct kmod-ath3k
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += asus_map-ac2200
|
|
|
|
|
|
ipq40xx: add support for ASUS RT-AC58U/RT-ACRH13
This patch adds support for ASUS RT-AC58U/RT-ACRH13.
hardware highlights:
SOC: IPQ4018 / QCA Dakota
CPU: Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7
DRAM: 128 MiB DDR3L-1066 @ 537 MHz (1074?) NT5CC64M16GP-DI
NOR: 2 MiB Macronix MX25L1606E (for boot, QSEE)
NAND: 128 MiB Winbond W25NO1GVZE1G (cal + kernel + root, UBI)
ETH: Qualcomm Atheros QCA8075 Gigabit Switch (4 x LAN, 1 x WAN)
USB: 1 x 3.0 (via Synopsys DesignWare DWC3 controller in the SoC)
WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2
WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2
INPUT: one Reset and one WPS button
LEDS: Status, WAN, WIFI1/2, USB and LAN (one blue LED for each)
Serial:
WARNING: The serial port needs a TTL/RS-232 3V3 level converter!
The Serial setting is 115200-8-N-1. The board has an unpopulated
1x4 0.1" header. The pinout (VDD, RX, GND, TX) is printed on the
PCB right next to the connector.
U-Boot Note: The ethernet driver isn't always reliable and can sometime
time out... Don't worry, just retry.
Access via the serial console is required. As well as a working
TFTP-server setup and the initramfs image. (If not provided, it
has to be built from the OpenWrt source. Make sure to enable
LZMA as the compression for the INITRAMFS!)
To install the image permanently, you have to do the following
steps in the listed order.
1. Open up the router.
There are four phillips screws hiding behind the four plastic
feets on the underside.
2. Connect the serial cable (See notes above)
3. Connect your router via one of the four LAN-ports (yellow)
to a PC which can set the IP-Address and ssh and scp from.
If possible set your PC's IPv4 Address to 192.168.1.70
(As this is the IP-Address the Router's bootloader expects
for the tftp server)
4. power up the router and enter the u-boot
choose option 1 to upload the initramfs image. And follow
through the ipv4 setup.
Wait for your router's status LED to stop blinking rapidly and
glow just blue. (The LAN LED should also be glowing blue).
3. Connect to the OpenWrt running in RAM
The default IPv4-Address of your router will be 192.168.1.1.
1. Copy over the openwrt-sysupgrade.bin image to your router's
temporary directory
# scp openwrt-sysupgrade.bin root@192.168.1.1:/tmp
2. ssh from your PC into your router as root.
# ssh root@192.168.1.1
The default OpenWrt-Image won't ask for a password. Simply hit the Enter-Key.
Once connected...: run the following commands on your temporary installation
3. delete the "jffs2" ubi partition to make room for your new root partition
# ubirmvol /dev/ubi0 --name=jffs2
4. install OpenWrt on the NAND Flash.
# sysupgrade -v /tmp/openwrt-sysupgrade.bin
- This will will automatically reboot the router -
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-03-07 08:13:10 +00:00
|
|
|
define Device/asus_rt-ac58u
|
|
|
|
|
$(call Device/FitImageLzma)
|
|
|
|
|
DEVICE_DTS := qcom-ipq4018-rt-ac58u
|
|
|
|
|
BLOCKSIZE := 128k
|
|
|
|
|
PAGESIZE := 2048
|
|
|
|
|
DTB_SIZE := 65536
|
|
|
|
|
DEVICE_TITLE := Asus RT-AC58U
|
|
|
|
|
IMAGE_SIZE := 20439364
|
|
|
|
|
FILESYSTEMS := squashfs
|
|
|
|
|
# Someone - in their infinite wisdom - decided to put the firmware
|
|
|
|
|
# version in front of the image name \03\00\00\04 => Version 3.0.0.4
|
|
|
|
|
# Since u-boot works with strings we either need another fixup step
|
|
|
|
|
# to add a version... or we are very careful not to add '\0' into that
|
|
|
|
|
# string and call it a day.... Yeah, we do the latter!
|
|
|
|
|
UIMAGE_NAME:=$(shell echo -e '\03\01\01\01RT-AC58U')
|
|
|
|
|
IMAGES := sysupgrade.bin
|
2018-04-19 07:12:22 +00:00
|
|
|
DEVICE_PACKAGES := kmod-usb-ledtrig-usbport
|
ipq40xx: add support for ASUS RT-AC58U/RT-ACRH13
This patch adds support for ASUS RT-AC58U/RT-ACRH13.
hardware highlights:
SOC: IPQ4018 / QCA Dakota
CPU: Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7
DRAM: 128 MiB DDR3L-1066 @ 537 MHz (1074?) NT5CC64M16GP-DI
NOR: 2 MiB Macronix MX25L1606E (for boot, QSEE)
NAND: 128 MiB Winbond W25NO1GVZE1G (cal + kernel + root, UBI)
ETH: Qualcomm Atheros QCA8075 Gigabit Switch (4 x LAN, 1 x WAN)
USB: 1 x 3.0 (via Synopsys DesignWare DWC3 controller in the SoC)
WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2
WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2
INPUT: one Reset and one WPS button
LEDS: Status, WAN, WIFI1/2, USB and LAN (one blue LED for each)
Serial:
WARNING: The serial port needs a TTL/RS-232 3V3 level converter!
The Serial setting is 115200-8-N-1. The board has an unpopulated
1x4 0.1" header. The pinout (VDD, RX, GND, TX) is printed on the
PCB right next to the connector.
U-Boot Note: The ethernet driver isn't always reliable and can sometime
time out... Don't worry, just retry.
Access via the serial console is required. As well as a working
TFTP-server setup and the initramfs image. (If not provided, it
has to be built from the OpenWrt source. Make sure to enable
LZMA as the compression for the INITRAMFS!)
To install the image permanently, you have to do the following
steps in the listed order.
1. Open up the router.
There are four phillips screws hiding behind the four plastic
feets on the underside.
2. Connect the serial cable (See notes above)
3. Connect your router via one of the four LAN-ports (yellow)
to a PC which can set the IP-Address and ssh and scp from.
If possible set your PC's IPv4 Address to 192.168.1.70
(As this is the IP-Address the Router's bootloader expects
for the tftp server)
4. power up the router and enter the u-boot
choose option 1 to upload the initramfs image. And follow
through the ipv4 setup.
Wait for your router's status LED to stop blinking rapidly and
glow just blue. (The LAN LED should also be glowing blue).
3. Connect to the OpenWrt running in RAM
The default IPv4-Address of your router will be 192.168.1.1.
1. Copy over the openwrt-sysupgrade.bin image to your router's
temporary directory
# scp openwrt-sysupgrade.bin root@192.168.1.1:/tmp
2. ssh from your PC into your router as root.
# ssh root@192.168.1.1
The default OpenWrt-Image won't ask for a password. Simply hit the Enter-Key.
Once connected...: run the following commands on your temporary installation
3. delete the "jffs2" ubi partition to make room for your new root partition
# ubirmvol /dev/ubi0 --name=jffs2
4. install OpenWrt on the NAND Flash.
# sysupgrade -v /tmp/openwrt-sysupgrade.bin
- This will will automatically reboot the router -
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-03-07 08:13:10 +00:00
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += asus_rt-ac58u
|
|
|
|
|
|
2018-02-21 19:40:50 +00:00
|
|
|
define Device/avm_fritzbox-4040
|
|
|
|
|
$(call Device/FitImageLzma)
|
2018-03-19 19:53:09 +00:00
|
|
|
DEVICE_DTS := qcom-ipq4018-fritz4040
|
2018-02-21 19:40:50 +00:00
|
|
|
BOARD_NAME := fritz4040
|
|
|
|
|
DEVICE_TITLE := AVM Fritz!Box 4040
|
|
|
|
|
IMAGE_SIZE := 29753344
|
2019-01-04 20:17:20 +00:00
|
|
|
UBOOT_PATH := $(STAGING_DIR_IMAGE)/uboot-fritz4040.bin
|
2018-05-15 23:57:16 +00:00
|
|
|
UBOOT_PARTITION_SIZE := 524288
|
|
|
|
|
IMAGES = eva.bin sysupgrade.bin
|
|
|
|
|
IMAGE/eva.bin := append-uboot | pad-to $$$$(UBOOT_PARTITION_SIZE) | append-kernel | append-rootfs | pad-rootfs
|
2018-02-21 19:40:50 +00:00
|
|
|
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
|
2019-01-04 20:17:20 +00:00
|
|
|
DEVICE_PACKAGES := fritz-tffs fritz-caldata
|
2018-02-21 19:40:50 +00:00
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += avm_fritzbox-4040
|
|
|
|
|
|
2019-02-18 22:58:34 +00:00
|
|
|
define Device/avm_fritzbox-7530
|
|
|
|
|
$(call Device/FitImageLzma)
|
|
|
|
|
DEVICE_DTS := qcom-ipq4019-fritzbox-7530
|
|
|
|
|
DEVICE_TITLE := AVM Fritz!Box 7530
|
2019-03-11 17:05:31 +00:00
|
|
|
DEVICE_PACKAGES := fritz-caldata fritz-tffs-nand ipq-wifi-avm_fritzbox-7530
|
2019-02-18 22:58:34 +00:00
|
|
|
IMAGES := sysupgrade.bin
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += avm_fritzbox-7530
|
|
|
|
|
|
2019-03-11 17:05:32 +00:00
|
|
|
define Device/avm_fritzrepeater-3000
|
|
|
|
|
$(call Device/FitImageLzma)
|
|
|
|
|
DEVICE_DTS := qcom-ipq4019-fritzrepeater-3000
|
|
|
|
|
DEVICE_TITLE := AVM Fritz!Repeater 3000
|
|
|
|
|
DEVICE_PACKAGES := ath10k-firmware-qca9984-ct fritz-caldata fritz-tffs-nand ipq-wifi-avm_fritzrepeater-3000
|
|
|
|
|
IMAGES := sysupgrade.bin
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += avm_fritzrepeater-3000
|
|
|
|
|
|
2018-03-02 10:56:53 +00:00
|
|
|
define Device/compex_wpj428
|
|
|
|
|
$(call Device/FitImage)
|
|
|
|
|
DEVICE_DTS := qcom-ipq4028-wpj428
|
|
|
|
|
DEVICE_DTS_CONFIG := config@4
|
|
|
|
|
BLOCKSIZE := 64k
|
|
|
|
|
DEVICE_TITLE := Compex WPJ428
|
|
|
|
|
IMAGE_SIZE := 31232k
|
|
|
|
|
KERNEL_SIZE := 4096k
|
|
|
|
|
IMAGES = sysupgrade.bin
|
|
|
|
|
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
|
2018-04-12 18:48:35 +00:00
|
|
|
DEVICE_PACKAGES := kmod-gpio-beeper
|
2018-03-02 10:56:53 +00:00
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += compex_wpj428
|
|
|
|
|
|
ipq40xx: add support for EnGenius EAP1300
SOC: IPQ4018 / QCA Dakota
CPU: Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7
DRAM: 256 MiB
NOR: 32 MiB
ETH: Qualcomm Atheros QCA8072
WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2
WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2
INPUT: RESET Button
LEDS: Power, LAN, MESH, WLAN 2.4GHz, WLAN 5GHz
1. Load Ramdisk via U-Boot
To set up the flash memory environment, do the following:
a. As a preliminary step, ensure that the board console port is connected to the PC using these RS232 parameters:
* 115200bps
* 8N1
b. Confirm that the PC is connected to the board using one of the Ethernet ports. Set a static ip 192.168.99.8 for Ethernet that connects to board. The PC must have a TFTP server launched and listening on the interface to which the board is connected. At this stage power up the board and, after a few seconds, press 4 and then any key during the countdown.
U-BOOT> set serverip 192.168.99.8 && set ipaddr 192.168.99.9 && tftpboot 0x84000000 openwrt.itb && bootm
2. Load image via GUI
a. Upgrade EAP1300 to FW v3.5.3.2
In the GUI, System Manager > Firmware > Firmware Upgrade, to do upgrade.
b. Transfer to OpenWrt from EnGenius.
In Firmware Upgrade page, to upgrade yours openwrt-ipq40xx-engenius_eap1300-squashfs-sysupgrade.bin.
3. Revert to EnGenius EAP1300
To flash openwrt-ipq40xx-engenius_eap1300-squashfs-factory.bin by using sysupgrade command and "DO NOT" keep configuration.
$ sysupgrade –n openwrt-ipq40xx-engenius_eap1300-squashfs-factory.bin
Signed-off-by: Steven Lin <steven.lin@senao.com>
2018-10-19 08:55:08 +00:00
|
|
|
define Device/engenius_eap1300
|
|
|
|
|
$(call Device/FitImage)
|
|
|
|
|
DEVICE_TITLE := EnGenius EAP1300
|
|
|
|
|
DEVICE_DTS_CONFIG := config@4
|
|
|
|
|
BOARD_NAME := eap1300
|
|
|
|
|
DEVICE_DTS := qcom-ipq4018-eap1300
|
|
|
|
|
KERNEL_SIZE := 5120k
|
|
|
|
|
IMAGE_SIZE := 25344k
|
|
|
|
|
IMAGES := sysupgrade.bin
|
|
|
|
|
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
|
|
|
|
|
DEVICE_PACKAGES := ipq-wifi-engenius_eap1300
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += engenius_eap1300
|
|
|
|
|
|
2019-02-27 22:48:23 +00:00
|
|
|
define Device/engenius_ens620ext
|
ipq40xx: add factory image for EnGenius ENS620EXT
Extended mksenaofw to support new "capwap" header structure.
This supports flashing from factory 3.0.0, 3.0.1, 3.1.0 and 3.5.5
firmware.
Note that the factory image format changes for 3.1 and later firmware,
and that the 3.1.0 and 3.5.5 Engenius firmware will refuse the
factory_30.bin file. Similarly, the 3.0.0 and 3.0.1 Engenius firmware
will refuse the factory_35.bin file.
Flashing from the Engenius 3.1.0 firmware with the factory_35.bin
firmware has not been tested, as 3.1.0 firmware (Engenius "middleFW")
is only intended as part of the upgrade path to 3.5.5 firmware.
Modified ipq40xx image Makefile to appropriately invoke mksenaofw
with new parameters to configure the capwap header.
Note that there is currently no method to return to factory firmware,
so this is a one-way street.
Path from factory 3.0.0 and 3.0.1 (EnGenius) software to OpenWrt is
to navigate to 192.168.1.1 on the stock firmware and navigate to the
firmware menu. Then copy the URL you have for that page, something like
http://192.168.1.1/cgi-bin/luci/;stok=12345abcdef/admin/system/flashops
and replace the trailing /admin/system/flashops with just /easyflashops
You should then be presented with a simple "Firmware Upgrade" page.
On that page, BE SURE TO CLEAR the "Keep Settings:" checkbox.
Choose the openwrt-ipq40xx-engenius_ens620ext-squashfs-factory_30.bin,
click "Upgrade" and on the following page select "Proceed".
Path from factory 3.5.5 (EnGenius) software to OpenWrt is simply to
use the stock firmware update menu. Choose the
openwrt-ipq40xx-engenius_ens620ext-squashfs-factory_35.bin and click
"Upload" and "Proceed".
The device should then flash the OpenWrt firmware and reboot. Note
that this resets the device to a default configuration with Wi-Fi
disabled, LAN1/PoE acting as a WAN port (running DHCP client) and LAN2
acting as a LAN port with a DHCP server on 192.168.1.x (AP is at
192.168.1.1)
Signed-off-by: Steve Glennon <s.glennon@cablelabs.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[sorry, for unfixing the 80-lines eyesores.]
2019-04-09 20:46:32 +00:00
|
|
|
$(call Device/FitImage)
|
|
|
|
|
DEVICE_DTS := qcom-ipq4018-ens620ext
|
|
|
|
|
DEVICE_DTS_CONFIG := config@4
|
|
|
|
|
BLOCKSIZE := 64k
|
|
|
|
|
PAGESIZE := 256
|
|
|
|
|
DEVICE_TITLE := EnGenius ENS620EXT
|
|
|
|
|
BOARD_NAME := ENS620EXT
|
|
|
|
|
VENDOR_ID := 0x0101
|
|
|
|
|
PRODUCT_ID := 0x79
|
|
|
|
|
PRODUCT_ID_NEW := 0xA4
|
|
|
|
|
DATECODE := 190507
|
|
|
|
|
FW_VER := 3.1.2
|
|
|
|
|
FW_VER_NEW := 3.5.6
|
|
|
|
|
CW_VER := 1.8.99
|
|
|
|
|
IMAGE_SIZE := 21823488
|
|
|
|
|
KERNEL_SIZE := 5120k
|
|
|
|
|
FILESYSTEMS := squashfs
|
|
|
|
|
IMAGES := sysupgrade.bin factory_30.bin factory_35.bin
|
|
|
|
|
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | check-size $$$$(IMAGE_SIZE) | append-metadata
|
|
|
|
|
IMAGE/factory_30.bin := append-kernel | pad-to $$$$(KERNEL_SIZE) | append-rootfs | pad-rootfs | check-size $$$$(IMAGE_SIZE) | SenaoFW $$$$(PRODUCT_ID) $$$$(FW_VER)
|
|
|
|
|
IMAGE/factory_35.bin := qsdk-ipq-factory-nor | check-size $$$$(IMAGE_SIZE) | SenaoFW $$$$(PRODUCT_ID_NEW) $$$$(FW_VER_NEW)
|
2019-02-27 22:48:23 +00:00
|
|
|
DEVICE_PACKAGES := ipq-wifi-engenius_ens620ext
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += engenius_ens620ext
|
|
|
|
|
|
2018-02-21 19:40:50 +00:00
|
|
|
define Device/glinet_gl-b1300
|
2018-02-17 08:07:54 +00:00
|
|
|
$(call Device/FitImage)
|
2018-02-21 19:40:50 +00:00
|
|
|
DEVICE_TITLE := GL.iNet GL-B1300
|
|
|
|
|
BOARD_NAME := gl-b1300
|
2018-02-17 08:07:54 +00:00
|
|
|
DEVICE_DTS := qcom-ipq4029-gl-b1300
|
2018-02-21 19:40:50 +00:00
|
|
|
KERNEL_SIZE := 4096k
|
|
|
|
|
IMAGE_SIZE := 26624k
|
|
|
|
|
IMAGES := sysupgrade.bin
|
2018-02-17 08:07:54 +00:00
|
|
|
IMAGE/sysupgrade.bin := append-kernel |append-rootfs | pad-rootfs | append-metadata
|
2018-02-21 19:40:50 +00:00
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += glinet_gl-b1300
|
|
|
|
|
|
2019-01-24 03:20:55 +00:00
|
|
|
define Device/linksys_ea6350v3
|
|
|
|
|
# The Linksys EA6350v3 has a uboot bootloader that does not
|
|
|
|
|
# support either booting lzma kernel images nor booting UBI
|
|
|
|
|
# partitions. This uboot, however, supports raw kernel images and
|
|
|
|
|
# gzipped images.
|
|
|
|
|
#
|
|
|
|
|
# As for the time of writing this, the device will boot the kernel
|
|
|
|
|
# from a fixed address with a fixed length of 3MiB. Also, the
|
|
|
|
|
# device has a hard-coded kernel command line that requieres the
|
|
|
|
|
# rootfs and alt_rootfs to be in mtd11 and mtd13 respectively.
|
|
|
|
|
# Oh... and the kernel partition overlaps with the rootfs
|
|
|
|
|
# partition (the same for alt_kernel and alt_rootfs).
|
|
|
|
|
#
|
|
|
|
|
# If you are planing re-partitioning the device, you may want to
|
|
|
|
|
# keep those details in mind:
|
|
|
|
|
# 1. The kernel adresses you should honor are 0x00000000 and
|
|
|
|
|
# 0x02800000 respectively.
|
|
|
|
|
# 2. The kernel size (plus the dtb) cannot exceed 3.00MiB in size.
|
|
|
|
|
# 3. You can use 'zImage', but not a raw 'Image' packed with lzma.
|
|
|
|
|
# 4. The kernel command line from uboot is harcoded to boot with
|
|
|
|
|
# rootfs either in mtd11 or mtd13.
|
|
|
|
|
$(call Device/FitzImage)
|
|
|
|
|
DEVICE_TITLE := Linksys EA6350v3
|
|
|
|
|
DEVICE_DTS := qcom-ipq4018-ea6350v3
|
|
|
|
|
BLOCKSIZE := 128k
|
|
|
|
|
PAGESIZE := 2048
|
|
|
|
|
KERNEL_SIZE := 3145728
|
|
|
|
|
IMAGE_SIZE := 38797312
|
|
|
|
|
UBINIZE_OPTS := -E 5
|
|
|
|
|
IMAGES := factory.bin sysupgrade.bin
|
|
|
|
|
IMAGE/factory.bin := append-kernel | append-uImage-fakehdr filesystem | pad-to $$$${KERNEL_SIZE} | append-ubi | linksys-image type=EA6350v3
|
|
|
|
|
DEVICE_PACKAGES := ipq-wifi-linksys_ea6350v3 uboot-envtools
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += linksys_ea6350v3
|
|
|
|
|
|
2018-03-10 09:59:18 +00:00
|
|
|
define Device/meraki_mr33
|
|
|
|
|
$(call Device/FitImage)
|
|
|
|
|
DEVICE_DTS := qcom-ipq4029-mr33
|
|
|
|
|
BLOCKSIZE := 131072
|
|
|
|
|
PAGESIZE := 2048
|
|
|
|
|
DEVICE_TITLE := Cisco Meraki MR33
|
|
|
|
|
IMAGES = sysupgrade.bin
|
2018-09-05 12:51:44 +00:00
|
|
|
DEVICE_PACKAGES := -swconfig ath10k-firmware-qca9887-ct
|
2018-03-10 09:59:18 +00:00
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += meraki_mr33
|
|
|
|
|
|
ipq40xx: add support for Netgear EX6100v2/EX6150v2
Specifications:
SOC: Qualcomm IPQ4018 (DAKOTA) ARM Quad-Core
RAM: 256 MB Winbond W632GU6KB12J
FLASH: 16 MiB Macronix MX25L12805D
ETH: Qualcomm QCA8072
WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11b/g/n/ac 2x2
WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11n/ac
1x1 (EX6100)
2x2 (EX6150)
INPUT: Power, WPS, reset button
AP / Range-extender toggle
LED: Power, Router, Extender (dual), WPS, Left-/Right-arrow
SERIAL: Header next to QCA8072 chip.
VCC, TX, RX, GND (Square hole is VCC)
WARNING: The serial port needs a TTL/RS-232 v3.3 level converter!
The Serial setting is 115200-8-N-1.
Tested and working:
- Ethernet
- 2.4 GHz WiFi (Correct MAC-address)
- 5 GHz WiFi (Correct MAC-address)
- Factory installation from WebIF
- Factory installation from tftp
- OpenWRT sysupgrade (Preserving and non-preserving)
- LEDs
- Buttons
Not Working:
- AP/Extender toggle-switch
Untested:
- Support on EX6100v2. They share the same GPL-Code and vendor-images.
The 6100v2 seems to lack one 5GHz stream and differs in the 5GHz
board-blob. I only own a EX6150v2, therefore i am only able to verify
functionality on this device.
Install via Web-Interface:
Upload the factory image to the device to the Netgear Web-Interface.
The device might asks you to confirm the update a second time due to
detecting the OpenWRT firmware as older. The device will automatically
reboot after the image is written to flash.
Install via TFTP:
Connect to the devices serial. Hit Enter-Key in bootloader to stop
autobooting. Command "fw_recovery" will start a tftp server, waiting for
a DNI image to be pushed.
Assign your computer the IP-address 192.168.1.10/24. Push image with
tftp -4 -v -m binary 192.168.1.1 -c put <OPENWRT_FACTORY>
Device will erase factory-partition first, then writes the pushed image
to flash and reboots.
Parts of this commit are based on Thomas Hebb's work on the
openwrt-devel mailinglist.
See https://lists.openwrt.org/pipermail/openwrt-devel/2018-January/043418.html
Signed-off-by: David Bauer <mail@david-bauer.net>
2018-03-28 22:32:38 +00:00
|
|
|
define Device/netgear_ex61x0v2
|
|
|
|
|
$(call Device/DniImage)
|
|
|
|
|
DEVICE_DTS_CONFIG := config@4
|
|
|
|
|
NETGEAR_BOARD_ID := EX6150v2series
|
|
|
|
|
NETGEAR_HW_ID := 29765285+16+0+128+2x2
|
|
|
|
|
endef
|
|
|
|
|
|
|
|
|
|
define Device/netgear_ex6100v2
|
|
|
|
|
$(call Device/netgear_ex61x0v2)
|
|
|
|
|
DEVICE_DTS := qcom-ipq4018-ex6100v2
|
|
|
|
|
DEVICE_TITLE := Netgear EX6100v2
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += netgear_ex6100v2
|
|
|
|
|
|
|
|
|
|
define Device/netgear_ex6150v2
|
|
|
|
|
$(call Device/netgear_ex61x0v2)
|
|
|
|
|
DEVICE_DTS := qcom-ipq4018-ex6150v2
|
|
|
|
|
DEVICE_TITLE := Netgear EX6150v2
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += netgear_ex6150v2
|
|
|
|
|
|
2018-02-21 19:40:50 +00:00
|
|
|
define Device/openmesh_a42
|
|
|
|
|
$(call Device/FitImageLzma)
|
2018-03-10 08:55:18 +00:00
|
|
|
DEVICE_DTS := qcom-ipq4018-a42
|
2018-03-19 11:36:13 +00:00
|
|
|
DEVICE_DTS_CONFIG := config@om.a42
|
2018-02-21 19:40:50 +00:00
|
|
|
BLOCKSIZE := 64k
|
|
|
|
|
DEVICE_TITLE := OpenMesh A42
|
|
|
|
|
KERNEL = kernel-bin | lzma | fit lzma $$(DTS_DIR)/$$(DEVICE_DTS).dtb | pad-to $$(BLOCKSIZE)
|
|
|
|
|
IMAGE_SIZE := 15616k
|
|
|
|
|
IMAGES = factory.bin sysupgrade.bin
|
|
|
|
|
IMAGE/factory.bin := append-rootfs | pad-rootfs | openmesh-image ce_type=A42
|
|
|
|
|
IMAGE/sysupgrade.bin/squashfs := append-rootfs | pad-rootfs | sysupgrade-tar rootfs=$$$$@ | append-metadata
|
2018-04-12 18:48:35 +00:00
|
|
|
DEVICE_PACKAGES := uboot-envtools
|
2018-02-21 19:40:50 +00:00
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += openmesh_a42
|
|
|
|
|
|
ipq40xx: add support for OpenMesh A62
* QCA IPQ4019
* 256 MB of RAM
* 32 MB of SPI NOR flash (s25fl256s1)
- 2x 15 MB available; but one of the 15 MB regions is the recovery image
* 2T2R 2.4 GHz
- QCA4019 hw1.0 (SoC)
- requires special BDF in QCA4019/hw1.0/board-2.bin with
bus=ahb,bmi-chip-id=0,bmi-board-id=20,variant=OM-A62
* 2T2R 5 GHz (channel 36-64)
- QCA9888 hw2.0 (PCI)
- requires special BDF in QCA9888/hw2.0/board-2.bin
bus=pci,bmi-chip-id=0,bmi-board-id=16,variant=OM-A62
* 2T2R 5 GHz (channel 100-165)
- QCA4019 hw1.0 (SoC)
- requires special BDF in QCA4019/hw1.0/board-2.bin with
bus=ahb,bmi-chip-id=0,bmi-board-id=21,variant=OM-A62
* multi-color LED (controlled via red/green/blue GPIOs)
* 1x button (reset; kmod-input-gpio-keys compatible)
* external watchdog
- triggered GPIO
* 1x USB (xHCI)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x gigabit ethernet
- phy@mdio3:
+ Label: Ethernet 1
+ gmac0 (ethaddr) in original firmware
+ 802.3at POE+
- phy@mdio4:
+ Label: Ethernet 2
+ gmac1 (eth1addr) in original firmware
+ 18-24V passive POE (mode B)
* powered only via POE
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the factory image to the u-boot when the device boots up.
The initramfs image can be started using
setenv bootargs 'loglevel=8 earlycon=msm_serial_dm,0x78af000 console=ttyMSM0,115200 mtdparts=spi0.0:256k(0:SBL1),128k(0:MIBIB),384k(0:QSEE),64k(0:CDT),64k(0:DDRPARAMS),64k(0:APPSBLENV),512k(0:APPSBL),64k(0:ART),64k(0:custom),64k(0:KEYS),15552k(inactive),15552k(inactive2)'
tftpboot 0x84000000 openwrt-ipq40xx-openmesh_a62-initramfs-fit-uImage.itb
set fdt_high 0x85000000
bootm 0x84000000
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
2017-08-09 11:52:07 +00:00
|
|
|
define Device/openmesh_a62
|
|
|
|
|
$(call Device/FitImageLzma)
|
|
|
|
|
DEVICE_DTS := qcom-ipq4019-a62
|
|
|
|
|
DEVICE_DTS_CONFIG := config@om.a62
|
|
|
|
|
BLOCKSIZE := 64k
|
|
|
|
|
DEVICE_TITLE := OpenMesh A62
|
|
|
|
|
KERNEL = kernel-bin | lzma | fit lzma $$(DTS_DIR)/$$(DEVICE_DTS).dtb | pad-to $$(BLOCKSIZE)
|
|
|
|
|
IMAGE_SIZE := 15552k
|
|
|
|
|
IMAGES = factory.bin sysupgrade.bin
|
|
|
|
|
IMAGE/factory.bin := append-rootfs | pad-rootfs | openmesh-image ce_type=A62
|
|
|
|
|
IMAGE/sysupgrade.bin/squashfs := append-rootfs | pad-rootfs | sysupgrade-tar rootfs=$$$$@ | append-metadata
|
2018-09-05 12:51:44 +00:00
|
|
|
DEVICE_PACKAGES := ath10k-firmware-qca9888-ct uboot-envtools
|
ipq40xx: add support for OpenMesh A62
* QCA IPQ4019
* 256 MB of RAM
* 32 MB of SPI NOR flash (s25fl256s1)
- 2x 15 MB available; but one of the 15 MB regions is the recovery image
* 2T2R 2.4 GHz
- QCA4019 hw1.0 (SoC)
- requires special BDF in QCA4019/hw1.0/board-2.bin with
bus=ahb,bmi-chip-id=0,bmi-board-id=20,variant=OM-A62
* 2T2R 5 GHz (channel 36-64)
- QCA9888 hw2.0 (PCI)
- requires special BDF in QCA9888/hw2.0/board-2.bin
bus=pci,bmi-chip-id=0,bmi-board-id=16,variant=OM-A62
* 2T2R 5 GHz (channel 100-165)
- QCA4019 hw1.0 (SoC)
- requires special BDF in QCA4019/hw1.0/board-2.bin with
bus=ahb,bmi-chip-id=0,bmi-board-id=21,variant=OM-A62
* multi-color LED (controlled via red/green/blue GPIOs)
* 1x button (reset; kmod-input-gpio-keys compatible)
* external watchdog
- triggered GPIO
* 1x USB (xHCI)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x gigabit ethernet
- phy@mdio3:
+ Label: Ethernet 1
+ gmac0 (ethaddr) in original firmware
+ 802.3at POE+
- phy@mdio4:
+ Label: Ethernet 2
+ gmac1 (eth1addr) in original firmware
+ 18-24V passive POE (mode B)
* powered only via POE
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the factory image to the u-boot when the device boots up.
The initramfs image can be started using
setenv bootargs 'loglevel=8 earlycon=msm_serial_dm,0x78af000 console=ttyMSM0,115200 mtdparts=spi0.0:256k(0:SBL1),128k(0:MIBIB),384k(0:QSEE),64k(0:CDT),64k(0:DDRPARAMS),64k(0:APPSBLENV),512k(0:APPSBL),64k(0:ART),64k(0:custom),64k(0:KEYS),15552k(inactive),15552k(inactive2)'
tftpboot 0x84000000 openwrt-ipq40xx-openmesh_a62-initramfs-fit-uImage.itb
set fdt_high 0x85000000
bootm 0x84000000
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
2017-08-09 11:52:07 +00:00
|
|
|
endef
|
|
|
|
|
|
|
|
|
|
TARGET_DEVICES += openmesh_a62
|
|
|
|
|
|
2018-02-21 19:40:50 +00:00
|
|
|
define Device/qcom_ap-dk01.1-c1
|
|
|
|
|
DEVICE_TITLE := QCA AP-DK01.1-C1
|
|
|
|
|
BOARD_NAME := ap-dk01.1-c1
|
|
|
|
|
DEVICE_DTS := qcom-ipq4019-ap.dk01.1-c1
|
|
|
|
|
KERNEL_INSTALL := 1
|
|
|
|
|
KERNEL_SIZE := 4096k
|
|
|
|
|
IMAGE_SIZE := 26624k
|
|
|
|
|
$(call Device/FitImage)
|
|
|
|
|
IMAGES := sysupgrade.bin
|
|
|
|
|
IMAGE/sysupgrade.bin := append-kernel | pad-to $$$${KERNEL_SIZE} | append-rootfs | pad-rootfs | append-metadata
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += qcom_ap-dk01.1-c1
|
|
|
|
|
|
|
|
|
|
define Device/qcom_ap-dk04.1-c1
|
|
|
|
|
$(call Device/FitImage)
|
|
|
|
|
$(call Device/UbiFit)
|
|
|
|
|
DEVICE_DTS := qcom-ipq4019-ap.dk04.1-c1
|
|
|
|
|
KERNEL_INSTALL := 1
|
|
|
|
|
KERNEL_SIZE := 4048k
|
|
|
|
|
BLOCKSIZE := 128k
|
|
|
|
|
PAGESIZE := 2048
|
|
|
|
|
BOARD_NAME := ap-dk04.1-c1
|
|
|
|
|
DEVICE_TITLE := QCA AP-DK04.1-C1
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += qcom_ap-dk04.1-c1
|
|
|
|
|
|
ipq40xx: add support for Qxwlan E2600AC C1 and C2
Qxwlan E2600AC C1 based on IPQ4019
Specifications:
SOC: Qualcomm IPQ4019
DRAM: 256 MiB
FLASH: 32 MiB Winbond W25Q256
ETH: Qualcomm QCA8075
WLAN: 5G + 5G/2.4G
* 2T2R 2.4/5 GHz
- QCA4019 hw1.0 (SoC)
* 2T2R 5 GHz
- QCA4019 hw1.0 (SoC)
INPUT: Reset buutton
LED: 1x Power ,6 driven by gpio
SERIAL: UART (J5)
UUSB: USB3.0
POWER: 1x DC jack for main power input (9-24 V)
SLOT: Pcie (J25), sim card (J11), SD card (J51)
Flash instruction (using U-Boot CLI and tftp server):
- Configure PC with static IP 192.168.1.10 and tftp server.
- Rename "sysupgrade" filename to "firmware.bin" and place it in tftp
server directory.
- Connect PC with one of RJ45 ports, power up the board and press
"enter" key to access U-Boot CLI.
- Use the following command to update the device to OpenWrt: "run lfw".
Flash instruction (using U-Boot web-based recovery):
- Configure PC with static IP 192.168.1.xxx(2-254)/24.
- Connect PC with one of RJ45 ports, press the reset button, power up
the board and keep button pressed for around 6-7 seconds, until LEDs
start flashing.
- Open your browser and enter 192.168.1.1, select "sysupgrade" image
and click the upgrade button.
Qxwlan E2600AC C2 based on IPQ4019
Specifications:
SOC: Qualcomm IPQ4019
DRAM: 256 MiB
NOR: 16 MiB Winbond W25Q128
NAND: 128MiB Micron MT29F1G08ABAEAWP
ETH: Qualcomm QCA8075
WLAN: 5G + 5G/2.4G
* 2T2R 2.4/5 GHz
- QCA4019 hw1.0 (SoC)
* 2T2R 5 GHz
- QCA4019 hw1.0 (SoC)
INPUT: Reset buutton
LED: 1x Power, 6 driven by gpio
SERIAL: UART (J5)
USB: USB3.0
POWER: 1x DC jack for main power input (9-24 V)
SLOT: Pcie (J25), sim card (J11), SD card (J51)
Flash instruction (using U-Boot CLI and tftp server):
- Configure PC with static IP 192.168.1.10 and tftp server.
- Rename "ubi" filename to "ubi-firmware.bin" and place it in tftp
server directory.
- Connect PC with one of RJ45 ports, power up the board and press
"enter" key to access U-Boot CLI.
- Use the following command to update the device to OpenWrt: "run lfw".
Flash instruction (using U-Boot web-based recovery):
- Configure PC with static IP 192.168.1.xxx(2-254)/24.
- Connect PC with one of RJ45 ports, press the reset button, power up
the board and keep button pressed for around 6-7 seconds, until LEDs
start flashing.
- Open your browser and enter 192.168.1.1, select "ubi" image
and click the upgrade button.
Signed-off-by: 张鹏 <sd20@qxwlan.com>
[ added rng node. whitespace fixes, ported 02_network,
ipq-wifi Makefile, misc dts fixes, trivial message changes ]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-01-21 05:28:32 +00:00
|
|
|
define Device/qxwlan_e2600ac-c1
|
|
|
|
|
$(call Device/FitImage)
|
|
|
|
|
DEVICE_TITLE := Qxwlan E2600AC-C1 (nor flash)
|
|
|
|
|
BOARD_NAME := e2600ac-c1
|
|
|
|
|
DEVICE_DTS := qcom-ipq4019-qxwlan-e2600ac-c1
|
|
|
|
|
KERNEL_SIZE := 4096k
|
|
|
|
|
IMAGE_SIZE := 31232k
|
|
|
|
|
IMAGES := sysupgrade.bin
|
|
|
|
|
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
|
|
|
|
|
DEVICE_PACKAGES := ipq-wifi-qxwlan_e2600ac
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += qxwlan_e2600ac-c1
|
|
|
|
|
|
|
|
|
|
define Device/qxwlan_e2600ac-c2
|
|
|
|
|
$(call Device/FitImage)
|
|
|
|
|
$(call Device/UbiFit)
|
|
|
|
|
DEVICE_DTS := qcom-ipq4019-qxwlan-e2600ac-c2
|
|
|
|
|
KERNEL_INSTALL := 1
|
|
|
|
|
BLOCKSIZE := 128k
|
|
|
|
|
PAGESIZE := 2048
|
|
|
|
|
DEVICE_TITLE := Qxwlan E2600AC-C2 (nornand flash)
|
|
|
|
|
DEVICE_PACKAGES := ipq-wifi-qxwlan_e2600ac
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += qxwlan_e2600ac-c2
|
|
|
|
|
|
ipq40xx: add support for the ZyXEL NBG6617
This patch adds support for ZyXEL NBG6617
Hardware highlights:
SOC: IPQ4018 / QCA Dakota
CPU: Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7
DRAM: 256 MiB DDR3L-1600/1866 Nanya NT5CC128M16IP-DI @ 537 MHz
NOR: 32 MiB Macronix MX25L25635F
ETH: Qualcomm Atheros QCA8075 Gigabit Switch (4 x LAN, 1 x WAN)
USB: 1 x 3.0 (via Synopsys DesignWare DWC3 controller in the SoC)
WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2
WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2
INPUT: RESET Button, WIFI/Rfkill Togglebutton, WPS Button
LEDS: Power, WAN, LAN 1-4, WLAN 2.4GHz, WLAN 5GHz, USB, WPS
Serial:
WARNING: The serial port needs a TTL/RS-232 3.3v level converter!
The Serial setting is 115200-8-N-1. The 1x4 .1" header comes
pre-soldered. Pinout:
1. 3v3 (Label printed on the PCB), 2. RX, 3. GND, 4. TX
first install / debricking / restore stock:
0. Have a PC running a tftp-server @ 192.168.1.99/24
1. connect the PC to any LAN-Ports
2. put the openwrt...-factory.bin (or V1.00(ABCT.X).bin for stock) file
into the tftp-server root directory and rename it to just "ras.bin".
3. power-cycle the router and hold down the the WPS button (for 30sek)
4. Wait (for a long time - the serial console provides some progress
reports. The u-boot says it best: "Please be patient".
5. Once the power LED starts to flashes slowly and the USB + WPS LEDs
flashes fast at the same time. You have to reboot the device and
it should then come right up.
Installation via Web-UI:
0. Connect a PC to the powered-on router. It will assign your PC a
IP-address via DHCP
1. Access the Web-UI at 192.168.1.1 (Default Passwort: 1234)
2. Go to the "Expert Mode"
3. Under "Maintenance", select "Firmware-Upgrade"
4. Upload the OpenWRT factory image
5. Wait for the Device to finish.
It will reboot into OpenWRT without any additional actions needed.
To open the ZyXEL NBG6617:
0. remove the four rubber feet glued on the backside
1. remove the four philips screws and pry open the top cover
(by applying force between the plastic top housing from the
backside/lan-port side)
Access the real u-boot shell:
ZyXEL uses a proprietary loader/shell on top of u-boot: "ZyXEL zloader v2.02"
When the device is starting up, the user can enter the the loader shell
by simply pressing a key within the 3 seconds once the following string
appears on the serial console:
| Hit any key to stop autoboot: 3
The user is then dropped to a locked shell.
|NBG6617> HELP
|ATEN x[,y] set BootExtension Debug Flag (y=password)
|ATSE x show the seed of password generator
|ATSH dump manufacturer related data in ROM
|ATRT [x,y,z,u] RAM read/write test (x=level, y=start addr, z=end addr, u=iterations)
|ATGO boot up whole system
|ATUR x upgrade RAS image (filename)
|NBG6617>
In order to escape/unlock a password challenge has to be passed.
Note: the value is dynamic! you have to calculate your own!
First use ATSE $MODELNAME (MODELNAME is the hostname in u-boot env)
to get the challange value/seed.
|NBG6617> ATSE NBG6617
|012345678901
This seed/value can be converted to the password with the help of this
bash script (Thanks to http://www.adslayuda.com/Zyxel650-9.html authors):
- tool.sh -
ror32() {
echo $(( ($1 >> $2) | (($1 << (32 - $2) & (2**32-1)) ) ))
}
v="0x$1"
a="0x${v:2:6}"
b=$(( $a + 0x10F0A563))
c=$(( 0x${v:12:14} & 7 ))
p=$(( $(ror32 $b $c) ^ $a ))
printf "ATEN 1,%X\n" $p
- end of tool.sh -
|# bash ./tool.sh 012345678901
|
|ATEN 1,879C711
copy and paste the result into the shell to unlock zloader.
|NBG6617> ATEN 1,0046B0017430
If the entered code was correct the shell will change to
use the ATGU command to enter the real u-boot shell.
|NBG6617> ATGU
|NBG6617#
Co-authored-by: David Bauer <mail@david-bauer.net>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: David Bauer <mail@david-bauer.net>
2018-06-21 12:24:59 +00:00
|
|
|
define Device/zyxel_nbg6617
|
|
|
|
|
$(call Device/FitImageLzma)
|
|
|
|
|
DEVICE_DTS := qcom-ipq4018-nbg6617
|
|
|
|
|
DEVICE_TITLE := ZyXEL NBG6617
|
|
|
|
|
ROOTFS_SIZE := 24960k
|
|
|
|
|
RAS_BOARD := NBG6617
|
|
|
|
|
RAS_ROOTFS_SIZE := 19840k
|
|
|
|
|
RAS_VERSION := "$(VERSION_DIST) $(REVISION)"
|
|
|
|
|
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
|
|
|
|
|
IMAGES := sysupgrade.bin factory.bin
|
|
|
|
|
# The ZyXEL firmware allows flashing thru the web-gui only when the rootfs is
|
|
|
|
|
# at least as large as the one of the initial firmware image (not the current
|
|
|
|
|
# one on the device). This only applies to the Web-UI, the bootlaoder ignores
|
|
|
|
|
# this minimum-size. However, the larger image can be flashed both ways.
|
2018-08-22 15:30:44 +00:00
|
|
|
IMAGE/factory.bin := append-rootfs | pad-rootfs | pad-to 64k | check-size $$$$(ROOTFS_SIZE) | zyxel-ras-image separate-kernel
|
ipq40xx: add support for the ZyXEL NBG6617
This patch adds support for ZyXEL NBG6617
Hardware highlights:
SOC: IPQ4018 / QCA Dakota
CPU: Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7
DRAM: 256 MiB DDR3L-1600/1866 Nanya NT5CC128M16IP-DI @ 537 MHz
NOR: 32 MiB Macronix MX25L25635F
ETH: Qualcomm Atheros QCA8075 Gigabit Switch (4 x LAN, 1 x WAN)
USB: 1 x 3.0 (via Synopsys DesignWare DWC3 controller in the SoC)
WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2
WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2
INPUT: RESET Button, WIFI/Rfkill Togglebutton, WPS Button
LEDS: Power, WAN, LAN 1-4, WLAN 2.4GHz, WLAN 5GHz, USB, WPS
Serial:
WARNING: The serial port needs a TTL/RS-232 3.3v level converter!
The Serial setting is 115200-8-N-1. The 1x4 .1" header comes
pre-soldered. Pinout:
1. 3v3 (Label printed on the PCB), 2. RX, 3. GND, 4. TX
first install / debricking / restore stock:
0. Have a PC running a tftp-server @ 192.168.1.99/24
1. connect the PC to any LAN-Ports
2. put the openwrt...-factory.bin (or V1.00(ABCT.X).bin for stock) file
into the tftp-server root directory and rename it to just "ras.bin".
3. power-cycle the router and hold down the the WPS button (for 30sek)
4. Wait (for a long time - the serial console provides some progress
reports. The u-boot says it best: "Please be patient".
5. Once the power LED starts to flashes slowly and the USB + WPS LEDs
flashes fast at the same time. You have to reboot the device and
it should then come right up.
Installation via Web-UI:
0. Connect a PC to the powered-on router. It will assign your PC a
IP-address via DHCP
1. Access the Web-UI at 192.168.1.1 (Default Passwort: 1234)
2. Go to the "Expert Mode"
3. Under "Maintenance", select "Firmware-Upgrade"
4. Upload the OpenWRT factory image
5. Wait for the Device to finish.
It will reboot into OpenWRT without any additional actions needed.
To open the ZyXEL NBG6617:
0. remove the four rubber feet glued on the backside
1. remove the four philips screws and pry open the top cover
(by applying force between the plastic top housing from the
backside/lan-port side)
Access the real u-boot shell:
ZyXEL uses a proprietary loader/shell on top of u-boot: "ZyXEL zloader v2.02"
When the device is starting up, the user can enter the the loader shell
by simply pressing a key within the 3 seconds once the following string
appears on the serial console:
| Hit any key to stop autoboot: 3
The user is then dropped to a locked shell.
|NBG6617> HELP
|ATEN x[,y] set BootExtension Debug Flag (y=password)
|ATSE x show the seed of password generator
|ATSH dump manufacturer related data in ROM
|ATRT [x,y,z,u] RAM read/write test (x=level, y=start addr, z=end addr, u=iterations)
|ATGO boot up whole system
|ATUR x upgrade RAS image (filename)
|NBG6617>
In order to escape/unlock a password challenge has to be passed.
Note: the value is dynamic! you have to calculate your own!
First use ATSE $MODELNAME (MODELNAME is the hostname in u-boot env)
to get the challange value/seed.
|NBG6617> ATSE NBG6617
|012345678901
This seed/value can be converted to the password with the help of this
bash script (Thanks to http://www.adslayuda.com/Zyxel650-9.html authors):
- tool.sh -
ror32() {
echo $(( ($1 >> $2) | (($1 << (32 - $2) & (2**32-1)) ) ))
}
v="0x$1"
a="0x${v:2:6}"
b=$(( $a + 0x10F0A563))
c=$(( 0x${v:12:14} & 7 ))
p=$(( $(ror32 $b $c) ^ $a ))
printf "ATEN 1,%X\n" $p
- end of tool.sh -
|# bash ./tool.sh 012345678901
|
|ATEN 1,879C711
copy and paste the result into the shell to unlock zloader.
|NBG6617> ATEN 1,0046B0017430
If the entered code was correct the shell will change to
use the ATGU command to enter the real u-boot shell.
|NBG6617> ATGU
|NBG6617#
Co-authored-by: David Bauer <mail@david-bauer.net>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: David Bauer <mail@david-bauer.net>
2018-06-21 12:24:59 +00:00
|
|
|
IMAGE/sysupgrade.bin/squashfs := append-rootfs | pad-rootfs | check-size $$$$(ROOTFS_SIZE) | sysupgrade-tar rootfs=$$$$@ | append-metadata
|
2018-12-21 18:06:49 +00:00
|
|
|
DEVICE_PACKAGES := uboot-envtools kmod-usb-ledtrig-usbport
|
ipq40xx: add support for the ZyXEL NBG6617
This patch adds support for ZyXEL NBG6617
Hardware highlights:
SOC: IPQ4018 / QCA Dakota
CPU: Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7
DRAM: 256 MiB DDR3L-1600/1866 Nanya NT5CC128M16IP-DI @ 537 MHz
NOR: 32 MiB Macronix MX25L25635F
ETH: Qualcomm Atheros QCA8075 Gigabit Switch (4 x LAN, 1 x WAN)
USB: 1 x 3.0 (via Synopsys DesignWare DWC3 controller in the SoC)
WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2
WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2
INPUT: RESET Button, WIFI/Rfkill Togglebutton, WPS Button
LEDS: Power, WAN, LAN 1-4, WLAN 2.4GHz, WLAN 5GHz, USB, WPS
Serial:
WARNING: The serial port needs a TTL/RS-232 3.3v level converter!
The Serial setting is 115200-8-N-1. The 1x4 .1" header comes
pre-soldered. Pinout:
1. 3v3 (Label printed on the PCB), 2. RX, 3. GND, 4. TX
first install / debricking / restore stock:
0. Have a PC running a tftp-server @ 192.168.1.99/24
1. connect the PC to any LAN-Ports
2. put the openwrt...-factory.bin (or V1.00(ABCT.X).bin for stock) file
into the tftp-server root directory and rename it to just "ras.bin".
3. power-cycle the router and hold down the the WPS button (for 30sek)
4. Wait (for a long time - the serial console provides some progress
reports. The u-boot says it best: "Please be patient".
5. Once the power LED starts to flashes slowly and the USB + WPS LEDs
flashes fast at the same time. You have to reboot the device and
it should then come right up.
Installation via Web-UI:
0. Connect a PC to the powered-on router. It will assign your PC a
IP-address via DHCP
1. Access the Web-UI at 192.168.1.1 (Default Passwort: 1234)
2. Go to the "Expert Mode"
3. Under "Maintenance", select "Firmware-Upgrade"
4. Upload the OpenWRT factory image
5. Wait for the Device to finish.
It will reboot into OpenWRT without any additional actions needed.
To open the ZyXEL NBG6617:
0. remove the four rubber feet glued on the backside
1. remove the four philips screws and pry open the top cover
(by applying force between the plastic top housing from the
backside/lan-port side)
Access the real u-boot shell:
ZyXEL uses a proprietary loader/shell on top of u-boot: "ZyXEL zloader v2.02"
When the device is starting up, the user can enter the the loader shell
by simply pressing a key within the 3 seconds once the following string
appears on the serial console:
| Hit any key to stop autoboot: 3
The user is then dropped to a locked shell.
|NBG6617> HELP
|ATEN x[,y] set BootExtension Debug Flag (y=password)
|ATSE x show the seed of password generator
|ATSH dump manufacturer related data in ROM
|ATRT [x,y,z,u] RAM read/write test (x=level, y=start addr, z=end addr, u=iterations)
|ATGO boot up whole system
|ATUR x upgrade RAS image (filename)
|NBG6617>
In order to escape/unlock a password challenge has to be passed.
Note: the value is dynamic! you have to calculate your own!
First use ATSE $MODELNAME (MODELNAME is the hostname in u-boot env)
to get the challange value/seed.
|NBG6617> ATSE NBG6617
|012345678901
This seed/value can be converted to the password with the help of this
bash script (Thanks to http://www.adslayuda.com/Zyxel650-9.html authors):
- tool.sh -
ror32() {
echo $(( ($1 >> $2) | (($1 << (32 - $2) & (2**32-1)) ) ))
}
v="0x$1"
a="0x${v:2:6}"
b=$(( $a + 0x10F0A563))
c=$(( 0x${v:12:14} & 7 ))
p=$(( $(ror32 $b $c) ^ $a ))
printf "ATEN 1,%X\n" $p
- end of tool.sh -
|# bash ./tool.sh 012345678901
|
|ATEN 1,879C711
copy and paste the result into the shell to unlock zloader.
|NBG6617> ATEN 1,0046B0017430
If the entered code was correct the shell will change to
use the ATGU command to enter the real u-boot shell.
|NBG6617> ATGU
|NBG6617#
Co-authored-by: David Bauer <mail@david-bauer.net>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: David Bauer <mail@david-bauer.net>
2018-06-21 12:24:59 +00:00
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += zyxel_nbg6617
|
|
|
|
|
|
ipq40xx: add support for ZyXEL WRE6606
Specifications:
SOC: Qualcomm IPQ4018 (DAKOTA) ARM Quad-Core
RAM: 128 MB Nanya NT5CC64M16GP-DI
FLASH: 16 MiB Macronix MX25L12845EMI-12G
ETH: Qualcomm QCA8072
WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11b/g/n 2x2
WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11n/ac W2 2x2
INPUT: WPS, Mode-toggle-switch
LED: Power, WLAN 2.4GHz, WLAN 5GHz, LAN, WPS
(LAN not controllable by software)
(WLAN each green / red)
SERIAL: Header next to eth-phy.
VCC, TX, GND, RX (Square hole is VCC)
The Serial setting is 115200-8-N-1.
Tested and working:
- Ethernet (Correct MAC-address)
- 2.4 GHz WiFi (Correct MAC-address)
- 5 GHz WiFi (Correct MAC-address)
- Factory installation from tftp
- OpenWRT sysupgrade
- LEDs
- WPS Button
Not Working:
- Mode-toggle-switch
Install via TFTP:
Connect to the devices serial. Hit Enter-Key in bootloader to stop
autobooting. Command `tftpboot` will pull an initramfs image named
`C0A86302.img` from a tftp server at `192.168.99.08/24`.
After successfull transfer, boot the image with `bootm`.
To persistently write the firmware, flash an openwrt sysupgrade image
from inside the initramfs, for example transfer
via `scp <sysupgrade> root@192.168.1.1:/tmp` and flash on the device
with `sysupgrade -n /tmp/<sysupgrade>`.
append-cmdline patch taken from chunkeeys work on the NBG6617.
Signed-off-by: Magnus Frühling <skorpy@frankfurt.ccc.de>
Co-authored-by: David Bauer <mail@david-bauer.net>
Co-authored-by: Christian Lamparter <chunkeey@googlemail.com>
2018-06-11 21:10:43 +00:00
|
|
|
define Device/zyxel_wre6606
|
|
|
|
|
$(call Device/FitImage)
|
|
|
|
|
DEVICE_TITLE := ZyXEL WRE6606
|
|
|
|
|
DEVICE_DTS_CONFIG := config@4
|
|
|
|
|
DEVICE_DTS := qcom-ipq4018-wre6606
|
|
|
|
|
IMAGES := sysupgrade.bin
|
|
|
|
|
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += zyxel_wre6606
|
|
|
|
|
|
2018-02-21 19:40:50 +00:00
|
|
|
$(eval $(call BuildImage))
|
