openwrt/target/linux/realtek/dts-5.15/rtl8380_hpe_1920-8g.dts

116 lines
2.3 KiB
Plaintext
Raw Normal View History

// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
#include "rtl838x.dtsi"
#include "rtl838x_hpe_1920.dtsi"
/ {
compatible = "hpe,1920-8g", "realtek,rtl838x-soc";
model = "HPE 1920-8G (JG920A)";
gpio1: rtl8231-gpio {
compatible = "realtek,rtl8231-gpio";
#gpio-cells = <2>;
gpio-controller;
indirect-access-bus-id = <0>;
};
i2c0: i2c-gpio-0 {
compatible = "i2c-gpio";
sda-gpios = <&gpio1 23 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
scl-gpios = <&gpio1 24 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
i2c-gpio,delay-us = <2>;
#address-cells = <1>;
#size-cells = <0>;
};
sfp0: sfp-0 {
compatible = "sff,sfp";
i2c-bus = <&i2c0>;
los-gpio = <&gpio1 26 GPIO_ACTIVE_HIGH>;
mod-def0-gpio = <&gpio1 25 GPIO_ACTIVE_LOW>;
// tx-fault and tx-disable unconnected
};
i2c1: i2c-gpio-1 {
compatible = "i2c-gpio";
sda-gpios = <&gpio1 13 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
scl-gpios = <&gpio1 14 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
i2c-gpio,delay-us = <2>;
#address-cells = <1>;
#size-cells = <0>;
};
sfp1: sfp-1 {
compatible = "sff,sfp";
i2c-bus = <&i2c1>;
los-gpio = <&gpio1 22 GPIO_ACTIVE_HIGH>;
mod-def0-gpio = <&gpio1 21 GPIO_ACTIVE_LOW>;
// tx-fault and tx-disable unconnected
};
};
&ethernet0 {
mdio: mdio-bus {
compatible = "realtek,rtl838x-mdio";
regmap = <&ethernet0>;
#address-cells = <1>;
#size-cells = <0>;
INTERNAL_PHY(8)
INTERNAL_PHY(9)
INTERNAL_PHY(10)
INTERNAL_PHY(11)
INTERNAL_PHY(12)
INTERNAL_PHY(13)
INTERNAL_PHY(14)
INTERNAL_PHY(15)
INTERNAL_PHY(24)
INTERNAL_PHY(26)
};
};
&switch0 {
ports {
#address-cells = <1>;
#size-cells = <0>;
SWITCH_PORT(8, 1, internal)
SWITCH_PORT(9, 2, internal)
SWITCH_PORT(10, 3, internal)
SWITCH_PORT(11, 4, internal)
SWITCH_PORT(12, 5, internal)
SWITCH_PORT(13, 6, internal)
SWITCH_PORT(14, 7, internal)
SWITCH_PORT(15, 8, internal)
port@24 {
reg = <24>;
label = "lan9";
phy-handle = <&phy24>;
phy-mode = "1000base-x";
managed = "in-band-status";
sfp = <&sfp0>;
};
port@26 {
reg = <26>;
label = "lan10";
phy-handle = <&phy26>;
phy-mode = "1000base-x";
managed = "in-band-status";
sfp = <&sfp1>;
};
port@28 {
ethernet = <&ethernet0>;
reg = <28>;
phy-mode = "internal";
fixed-link {
speed = <1000>;
full-duplex;
};
};
};
};