ExternalVendorCode/openwrt
1
0
Fork 0
mirror of https://github.com/openwrt/openwrt.git synced 2024-12-26 00:41:17 +00:00
Code Issues Actions Packages Projects Releases Wiki Activity
a57fcd880e
openwrt/target/linux/ath79/image/generic-ubnt.mk

313 lines
7.9 KiB
Makefile
Raw Normal View History

ath79: ubnt-m-xw: Fix factory image flashing using TFTP recovery method Ubiquity allows flashing of unsigned factory images via TFTP recovery method[1]. They claim in airOS v6.0.7 release changelog[2] following: All future airOS versions will be signed in this way and not allow unsigned firmware to be loaded except via TFTP. U-boot bootloader on M-XW devices expects factory image revision version in specific format. On airOS v6.1.7 with `U-Boot 1.1.4-s1039 (May 24 2017 - 15:58:18)` bootloader checks if the revision major(?) number is actually a number, but in currently generated images there's OpenWrt text and so the check fails: Hit any key to stop autoboot: 0 Setting default IP 192.168.1.20 Starting TFTP server... Receiving file from 192.168.1.25:38438 Received 4981148 bytes Firmware check failed! (1) By placing arbitrary correct number first in major version, we make the bootloader happy and we can flash factory images over TFTP again: Received 3735964 bytes Firmware Version: XW.ar934x.v6.0.4-42.r8474-56aa1ac-OpenWrt Setting U-Boot environment variables Un-Protected 1 sectors Erasing Flash.... done Patch provided by AREDN[3] project, tested on Bullet M2 XW (ynezz) and Nanostation M5 XW (ae6xe). 1. https://help.ubnt.com/hc/en-us/articles/204910124-UniFi-TFTP-Recovery-for-Bricked-Access-Points 2. https://dl.ubnt.com/firmwares/XW-fw/v6.0.7/changelog.txt 3. https://github.com/aredn Signed-off-by: Petr Štetiar <ynezz@true.cz>
2018-11-19 20:44:50 +00:00
DEVICE_VARS += UBNT_BOARD UBNT_CHIP UBNT_TYPE UBNT_VERSION UBNT_REVISION
# On M (XW) devices the U-Boot as of version 1.1.4-s1039 doesn't like
# VERSION_DIST being on the place of major(?) version number, so we need to
# use some number.
UBNT_REVISION := $(VERSION_DIST)-$(REVISION)
ath79: add new OF only target for QCA MIPS silicon This target aims to replace ar71xx mid-term. The big part that is still missing is making the MMIO/AHB wifi work using OF. NAND and mikrotik subtargets will follow. Signed-off-by: John Crispin <john@phrozen.org>
2018-05-06 08:20:11 +00:00
# mkubntimage is using the kernel image direct
# routerboard creates partitions out of the ubnt header
define Build/mkubntimage
ath79: harmonize line breaks in image Makefiles This harmonizes the line wrapping in image Makefile device definitions, as those are frequently copy-pasted and are a common subject of review comments. Having the treatment unifying should reduce the cases where adjustment is necessary afterwards. Harmonization is achieved by consistently (read "strictly") applying certain rules: - Never put more than 80 characters into one line - Fill lines up (do not break after 40 chars because of ...) - Use one tab for indent after wrapping by "\" - Only break after pipe "|" for IMAGE variables Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-12-19 19:42:19 +00:00
-$(STAGING_DIR_HOST)/bin/mkfwimage -B $(UBNT_BOARD) \
-v $(UBNT_TYPE).$(UBNT_CHIP).v6.0.0-$(VERSION_DIST)-$(REVISION) \
-k $(IMAGE_KERNEL) -r $@ -o $@
ath79: add new OF only target for QCA MIPS silicon This target aims to replace ar71xx mid-term. The big part that is still missing is making the MMIO/AHB wifi work using OF. NAND and mikrotik subtargets will follow. Signed-off-by: John Crispin <john@phrozen.org>
2018-05-06 08:20:11 +00:00
endef
ath79: Add support for Ubiquiti NanoStation AC loco Atheros AR9342, 16 MB flash, 64 MB RAM Successor to the old NanoStation M5 loco with AC wireless. Includes a mac80211 patch for ath10k_pci because Ubiquiti uses a Ubiquiti branded and customized QCA988X with vendor id 0777 and device id 11ac for AC wireless. Installation 1. Connect to serial header on device (8N1 115200) 2. Power on device and enter uboot console 3. Set up tftp server serving an openwrt initramfs build 4. Load initramfs build using the command tftpboot in the uboot cli 5. Boot the loaded image using the command bootm 6. Copy squashfs openwrt sysupgrade build to the booted device 7. Use mtd to write sysupgrade to partition "firmware" 8. Reboot and enjoy Signed-off-by: Tobias Schramm <tobleminer@gmail.com>
2018-01-23 10:36:41 +00:00
# all UBNT XM/WA devices expect the kernel image to have 1024k while flash, when
ath79: add new OF only target for QCA MIPS silicon This target aims to replace ar71xx mid-term. The big part that is still missing is making the MMIO/AHB wifi work using OF. NAND and mikrotik subtargets will follow. Signed-off-by: John Crispin <john@phrozen.org>
2018-05-06 08:20:11 +00:00
# booting the image, the size doesn't matter.
define Build/mkubntimage-split
-[ -f $@ ] && ( \
dd if=$@ of=$@.old1 bs=1024k count=1; \
dd if=$@ of=$@.old2 bs=1024k skip=1; \
ath79: harmonize line breaks in image Makefiles This harmonizes the line wrapping in image Makefile device definitions, as those are frequently copy-pasted and are a common subject of review comments. Having the treatment unifying should reduce the cases where adjustment is necessary afterwards. Harmonization is achieved by consistently (read "strictly") applying certain rules: - Never put more than 80 characters into one line - Fill lines up (do not break after 40 chars because of ...) - Use one tab for indent after wrapping by "\" - Only break after pipe "|" for IMAGE variables Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-12-19 19:42:19 +00:00
$(STAGING_DIR_HOST)/bin/mkfwimage -B $(UBNT_BOARD) \
-v $(UBNT_TYPE).$(UBNT_CHIP).v$(UBNT_VERSION)-$(UBNT_REVISION) \
-k $@.old1 -r $@.old2 -o $@; \
ath79: add new OF only target for QCA MIPS silicon This target aims to replace ar71xx mid-term. The big part that is still missing is making the MMIO/AHB wifi work using OF. NAND and mikrotik subtargets will follow. Signed-off-by: John Crispin <john@phrozen.org>
2018-05-06 08:20:11 +00:00
rm $@.old1 $@.old2 )
endef
# UBNT_BOARD e.g. one of (XS2, XS5, RS, XM)
# UBNT_TYPE e.g. one of (BZ, XM, XW)
# UBNT_CHIP e.g. one of (ar7240, ar933x, ar934x)
ath79: Add support for Ubiquiti NanoStation AC loco Atheros AR9342, 16 MB flash, 64 MB RAM Successor to the old NanoStation M5 loco with AC wireless. Includes a mac80211 patch for ath10k_pci because Ubiquiti uses a Ubiquiti branded and customized QCA988X with vendor id 0777 and device id 11ac for AC wireless. Installation 1. Connect to serial header on device (8N1 115200) 2. Power on device and enter uboot console 3. Set up tftp server serving an openwrt initramfs build 4. Load initramfs build using the command tftpboot in the uboot cli 5. Boot the loaded image using the command bootm 6. Copy squashfs openwrt sysupgrade build to the booted device 7. Use mtd to write sysupgrade to partition "firmware" 8. Reboot and enjoy Signed-off-by: Tobias Schramm <tobleminer@gmail.com>
2018-01-23 10:36:41 +00:00
# UBNT_VERSION e.g. one of (6.0.0, 8.5.0)
ath79: add new OF only target for QCA MIPS silicon This target aims to replace ar71xx mid-term. The big part that is still missing is making the MMIO/AHB wifi work using OF. NAND and mikrotik subtargets will follow. Signed-off-by: John Crispin <john@phrozen.org>
2018-05-06 08:20:11 +00:00
define Device/ubnt
ath79: split DEVICE_TITLE in multiple variables This allows the definition of DEVICE_VENDOR, DEVICE_MODEL and DEVICE_VARIANT. All three are merged together to look the same as the current DEVICE_TITLE. Also, if DEVICE_TITLE is set it's directly used as a *fallback* for devices which weren't upgraded yet. This is based on the work of @sudhanshu16. The motivation is to create JSON files based on provided metadata, needing clear differentiation between vendor, model and revision. Signed-off-by: Paul Spooren <mail@aparcar.org>
2019-06-16 19:34:46 +00:00
DEVICE_VENDOR := Ubiquiti
treewide: remove kmod-usb-core from DEVICE_PACKAGES This removes _all_ occurrences of kmod-usb-core from DEVICE_PACKAGES and similar variables. This package is pulled as dependency by one of the following packages in any case: - kmod-usb-chipidea - kmod-usb-dwc2 - kmod-usb-ledtrig-usbport - kmod-usb-ohci - kmod-usb2 - kmod-usb2-pci - kmod-usb3 Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> [remove kmod-usb-core from EnGenius ESR600] Signed-off-by: David Bauer <mail@david-bauer.net>
2019-09-22 10:06:25 +00:00
DEVICE_PACKAGES := kmod-usb2
ath79: add and enforce image metadata Add metadata to images and make the metdata mandatory. Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-05-07 20:41:04 +00:00
IMAGES += factory.bin
IMAGE/factory.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | \
append-rootfs | pad-rootfs | check-size $$$$(IMAGE_SIZE) | mkubntimage-split
ath79: add new OF only target for QCA MIPS silicon This target aims to replace ar71xx mid-term. The big part that is still missing is making the MMIO/AHB wifi work using OF. NAND and mikrotik subtargets will follow. Signed-off-by: John Crispin <john@phrozen.org>
2018-05-06 08:20:11 +00:00
endef
define Device/ubnt-bz
$(Device/ubnt)
ath79: rename ATH_SOC to SOC This replaces ATH_SOC by the newly introduced common SOC device variable. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-12-20 00:12:42 +00:00
SOC := ar7241
ath79: tidy up and fix IMAGE_SIZE for Ubiquiti devices This addresses IMAGE_SIZE inconsistencies in generic_ubnt.mk by: 1. (cosmetical) Move IMAGE_SIZE out of top definition ("ubnt"), since despite two all subdefinition have different values. 2. (change) Fix IMAGE_SIZE for ubnt-xm and ubnt-bz (7552k->7488k). 3. (cosmetical) Move IMAGE_SIZE of ubnt-wa devices to parent node since all have same size (it is defined in parent DTSI ...). Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-10-22 11:08:23 +00:00
IMAGE_SIZE := 7448k
ath79: redistribute UBNT variables in Ubiquiti image Makefile The variables UBNT_BOARD and UBNT_VERSION are defined in the parent Device/ubnt definition and then overwritten for most of the derived platform definitions (e.g. Device/ubnt-wa). Since this mixed use of inheritance and overwriting can be misleading, this moves the variables to the platform-based definitions. While at it, reorder the definitions to have order consistent, too. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-12-06 12:56:51 +00:00
UBNT_BOARD := XM
ath79: add new OF only target for QCA MIPS silicon This target aims to replace ar71xx mid-term. The big part that is still missing is making the MMIO/AHB wifi work using OF. NAND and mikrotik subtargets will follow. Signed-off-by: John Crispin <john@phrozen.org>
2018-05-06 08:20:11 +00:00
UBNT_CHIP := ar7240
ath79: redistribute UBNT variables in Ubiquiti image Makefile The variables UBNT_BOARD and UBNT_VERSION are defined in the parent Device/ubnt definition and then overwritten for most of the derived platform definitions (e.g. Device/ubnt-wa). Since this mixed use of inheritance and overwriting can be misleading, this moves the variables to the platform-based definitions. While at it, reorder the definitions to have order consistent, too. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-12-06 12:56:51 +00:00
UBNT_TYPE := BZ
UBNT_VERSION := 6.0.0
ath79: add new OF only target for QCA MIPS silicon This target aims to replace ar71xx mid-term. The big part that is still missing is making the MMIO/AHB wifi work using OF. NAND and mikrotik subtargets will follow. Signed-off-by: John Crispin <john@phrozen.org>
2018-05-06 08:20:11 +00:00
endef
ath79: add support for Ubiquiti SW devices SW devices are Ubiquit ToughSwitch and EdgeSwitch series devices. Hardware-wise they are very similar to the XM device series. Signed-off-by: Tobias Schramm <tobleminer@gmail.com>
2019-12-03 21:39:01 +00:00
define Device/ubnt-sw
$(Device/ubnt)
SOC := ar7242
DEVICE_PACKAGES += kmod-usb-ohci
IMAGE_SIZE := 7552k
UBNT_BOARD := SW
UBNT_CHIP := ar7240
UBNT_TYPE := SW
UBNT_VERSION := 1.4.1
KERNEL := kernel-bin | append-dtb | relocate-kernel | lzma | uImage lzma
endef
ath79: Add support for Ubiquiti NanoStation AC loco Atheros AR9342, 16 MB flash, 64 MB RAM Successor to the old NanoStation M5 loco with AC wireless. Includes a mac80211 patch for ath10k_pci because Ubiquiti uses a Ubiquiti branded and customized QCA988X with vendor id 0777 and device id 11ac for AC wireless. Installation 1. Connect to serial header on device (8N1 115200) 2. Power on device and enter uboot console 3. Set up tftp server serving an openwrt initramfs build 4. Load initramfs build using the command tftpboot in the uboot cli 5. Boot the loaded image using the command bootm 6. Copy squashfs openwrt sysupgrade build to the booted device 7. Use mtd to write sysupgrade to partition "firmware" 8. Reboot and enjoy Signed-off-by: Tobias Schramm <tobleminer@gmail.com>
2018-01-23 10:36:41 +00:00
define Device/ubnt-wa
$(Device/ubnt)
ath79: rename ATH_SOC to SOC This replaces ATH_SOC by the newly introduced common SOC device variable. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-12-20 00:12:42 +00:00
SOC := ar9342
ath79: tidy up and fix IMAGE_SIZE for Ubiquiti devices This addresses IMAGE_SIZE inconsistencies in generic_ubnt.mk by: 1. (cosmetical) Move IMAGE_SIZE out of top definition ("ubnt"), since despite two all subdefinition have different values. 2. (change) Fix IMAGE_SIZE for ubnt-xm and ubnt-bz (7552k->7488k). 3. (cosmetical) Move IMAGE_SIZE of ubnt-wa devices to parent node since all have same size (it is defined in parent DTSI ...). Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-10-22 11:08:23 +00:00
IMAGE_SIZE := 15744k
ath79: Add support for Ubiquiti NanoStation AC loco Atheros AR9342, 16 MB flash, 64 MB RAM Successor to the old NanoStation M5 loco with AC wireless. Includes a mac80211 patch for ath10k_pci because Ubiquiti uses a Ubiquiti branded and customized QCA988X with vendor id 0777 and device id 11ac for AC wireless. Installation 1. Connect to serial header on device (8N1 115200) 2. Power on device and enter uboot console 3. Set up tftp server serving an openwrt initramfs build 4. Load initramfs build using the command tftpboot in the uboot cli 5. Boot the loaded image using the command bootm 6. Copy squashfs openwrt sysupgrade build to the booted device 7. Use mtd to write sysupgrade to partition "firmware" 8. Reboot and enjoy Signed-off-by: Tobias Schramm <tobleminer@gmail.com>
2018-01-23 10:36:41 +00:00
UBNT_BOARD := WA
ath79: redistribute UBNT variables in Ubiquiti image Makefile The variables UBNT_BOARD and UBNT_VERSION are defined in the parent Device/ubnt definition and then overwritten for most of the derived platform definitions (e.g. Device/ubnt-wa). Since this mixed use of inheritance and overwriting can be misleading, this moves the variables to the platform-based definitions. While at it, reorder the definitions to have order consistent, too. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-12-06 12:56:51 +00:00
UBNT_CHIP := ar934x
UBNT_TYPE := WA
ath79: Add support for Ubiquiti NanoStation AC loco Atheros AR9342, 16 MB flash, 64 MB RAM Successor to the old NanoStation M5 loco with AC wireless. Includes a mac80211 patch for ath10k_pci because Ubiquiti uses a Ubiquiti branded and customized QCA988X with vendor id 0777 and device id 11ac for AC wireless. Installation 1. Connect to serial header on device (8N1 115200) 2. Power on device and enter uboot console 3. Set up tftp server serving an openwrt initramfs build 4. Load initramfs build using the command tftpboot in the uboot cli 5. Boot the loaded image using the command bootm 6. Copy squashfs openwrt sysupgrade build to the booted device 7. Use mtd to write sysupgrade to partition "firmware" 8. Reboot and enjoy Signed-off-by: Tobias Schramm <tobleminer@gmail.com>
2018-01-23 10:36:41 +00:00
UBNT_VERSION := 8.5.0
endef
ath79: sort device definitions in image/* This applies alphabetic sorting to devices in image/* files. For certain cases, this patch deviates from strict sorting, e.g. to ensure that v10 comes after v9. While at it, fix an indent and remove some useless empty lines. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-08-22 12:34:45 +00:00
define Device/ubnt-xm
$(Device/ubnt)
ath79: rename ATH_SOC to SOC This replaces ATH_SOC by the newly introduced common SOC device variable. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-12-20 00:12:42 +00:00
SOC := ar7241
ath79: sort device definitions in image/* This applies alphabetic sorting to devices in image/* files. For certain cases, this patch deviates from strict sorting, e.g. to ensure that v10 comes after v9. While at it, fix an indent and remove some useless empty lines. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-08-22 12:34:45 +00:00
DEVICE_VARIANT := XM
ath79: include rssileds package for ubnt devices with LEDs Some Ubiquiti devices had the RSSI LEDs configured in 01_leds but were missing the rssileds package, while others that don't have RSSI LEDS had the package included. This commit includes the rssileds package only for those devices that need it. Tested on a NanoStation M XW. Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
2019-11-13 15:18:59 +00:00
DEVICE_PACKAGES += kmod-usb-ohci
ath79: tidy up and fix IMAGE_SIZE for Ubiquiti devices This addresses IMAGE_SIZE inconsistencies in generic_ubnt.mk by: 1. (cosmetical) Move IMAGE_SIZE out of top definition ("ubnt"), since despite two all subdefinition have different values. 2. (change) Fix IMAGE_SIZE for ubnt-xm and ubnt-bz (7552k->7488k). 3. (cosmetical) Move IMAGE_SIZE of ubnt-wa devices to parent node since all have same size (it is defined in parent DTSI ...). Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-10-22 11:08:23 +00:00
IMAGE_SIZE := 7448k
ath79: redistribute UBNT variables in Ubiquiti image Makefile The variables UBNT_BOARD and UBNT_VERSION are defined in the parent Device/ubnt definition and then overwritten for most of the derived platform definitions (e.g. Device/ubnt-wa). Since this mixed use of inheritance and overwriting can be misleading, this moves the variables to the platform-based definitions. While at it, reorder the definitions to have order consistent, too. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-12-06 12:56:51 +00:00
UBNT_BOARD := XM
ath79: sort device definitions in image/* This applies alphabetic sorting to devices in image/* files. For certain cases, this patch deviates from strict sorting, e.g. to ensure that v10 comes after v9. While at it, fix an indent and remove some useless empty lines. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-08-22 12:34:45 +00:00
UBNT_CHIP := ar7240
ath79: redistribute UBNT variables in Ubiquiti image Makefile The variables UBNT_BOARD and UBNT_VERSION are defined in the parent Device/ubnt definition and then overwritten for most of the derived platform definitions (e.g. Device/ubnt-wa). Since this mixed use of inheritance and overwriting can be misleading, this moves the variables to the platform-based definitions. While at it, reorder the definitions to have order consistent, too. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-12-06 12:56:51 +00:00
UBNT_TYPE := XM
UBNT_VERSION := 6.0.0
ath79: sort device definitions in image/* This applies alphabetic sorting to devices in image/* files. For certain cases, this patch deviates from strict sorting, e.g. to ensure that v10 comes after v9. While at it, fix an indent and remove some useless empty lines. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-08-22 12:34:45 +00:00
KERNEL := kernel-bin | append-dtb | relocate-kernel | lzma | uImage lzma
endef
ath79: Add support for Ubiquity Bullet M (XW) CPU: AR9342 SoC RAM: 64 MB DDR2 Flash: 8 MB NOR SPI Ports: 100 MBit (24V PoE in) WLAN: 2.4/5 GHz UART: 1 UART on PCB marked as J1 with 115200 8N1 config LEDs: Power, Ethernet, 4x RSSI LEDs (orange, red, 2x green) Buttons: Reset UART connection details .---------------------------------. | | [ETH] J1 [ANT] | o VCC o RX o TX o GND | `---------------------------------' Flashing instructions A) Serial console, U-Boot and TFTP 1. Connect to serial header J1 on the PCB 2. Power on device and enter U-Boot console 3. Set up TFTP server serving an OpenWrt initramfs build 4. Load initramfs build using the command tftpboot in the U-Boot cli 5. Boot the loaded image using the command bootm 6. Copy squashfs OpenWrt sysupgrade build to the booted device 7. Use mtd to write sysupgrade to partition "firmware" 8. Reboot and enjoy B) Experimental factory image flashing over SSH from airOS v6.1.7 1. You need to flash your UBNT M2HP with airOS v6.1.7 firmware no other airOS version is currently supported 2. git clone https://github.com/true-systems/ubnt-bullet-m2hp-openwrt-flashing 3. cd ubnt-bullet-m2hp-openwrt-flashing 4. make flash-factory FW_OWRT=/path/to/your/openwrt-ath79-generic-ubnt_bullet-m-xw-squashfs-factory.bin Tested only on Bullet M2HP. Signed-off-by: Petr Štetiar <ynezz@true.cz>
2018-11-17 07:01:55 +00:00
define Device/ubnt-xw
$(Device/ubnt)
ath79: rename ATH_SOC to SOC This replaces ATH_SOC by the newly introduced common SOC device variable. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-12-20 00:12:42 +00:00
SOC := ar9342
ath79: add XM device variant for Ubiquiti devices So far, XW devices have DEVICE_VARIANT defined and XM devices have no DEVICE_VARIANT set. This adds DEVICE_VARIANT for XM devices, and moves definitions for both XM and XW to the common definitions. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-09-18 19:36:46 +00:00
DEVICE_VARIANT := XW
ath79: tidy up and fix IMAGE_SIZE for Ubiquiti devices This addresses IMAGE_SIZE inconsistencies in generic_ubnt.mk by: 1. (cosmetical) Move IMAGE_SIZE out of top definition ("ubnt"), since despite two all subdefinition have different values. 2. (change) Fix IMAGE_SIZE for ubnt-xm and ubnt-bz (7552k->7488k). 3. (cosmetical) Move IMAGE_SIZE of ubnt-wa devices to parent node since all have same size (it is defined in parent DTSI ...). Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-10-22 11:08:23 +00:00
IMAGE_SIZE := 7552k
ath79: Add support for Ubiquity Bullet M (XW) CPU: AR9342 SoC RAM: 64 MB DDR2 Flash: 8 MB NOR SPI Ports: 100 MBit (24V PoE in) WLAN: 2.4/5 GHz UART: 1 UART on PCB marked as J1 with 115200 8N1 config LEDs: Power, Ethernet, 4x RSSI LEDs (orange, red, 2x green) Buttons: Reset UART connection details .---------------------------------. | | [ETH] J1 [ANT] | o VCC o RX o TX o GND | `---------------------------------' Flashing instructions A) Serial console, U-Boot and TFTP 1. Connect to serial header J1 on the PCB 2. Power on device and enter U-Boot console 3. Set up TFTP server serving an OpenWrt initramfs build 4. Load initramfs build using the command tftpboot in the U-Boot cli 5. Boot the loaded image using the command bootm 6. Copy squashfs OpenWrt sysupgrade build to the booted device 7. Use mtd to write sysupgrade to partition "firmware" 8. Reboot and enjoy B) Experimental factory image flashing over SSH from airOS v6.1.7 1. You need to flash your UBNT M2HP with airOS v6.1.7 firmware no other airOS version is currently supported 2. git clone https://github.com/true-systems/ubnt-bullet-m2hp-openwrt-flashing 3. cd ubnt-bullet-m2hp-openwrt-flashing 4. make flash-factory FW_OWRT=/path/to/your/openwrt-ath79-generic-ubnt_bullet-m-xw-squashfs-factory.bin Tested only on Bullet M2HP. Signed-off-by: Petr Štetiar <ynezz@true.cz>
2018-11-17 07:01:55 +00:00
UBNT_BOARD := XM
ath79: redistribute UBNT variables in Ubiquiti image Makefile The variables UBNT_BOARD and UBNT_VERSION are defined in the parent Device/ubnt definition and then overwritten for most of the derived platform definitions (e.g. Device/ubnt-wa). Since this mixed use of inheritance and overwriting can be misleading, this moves the variables to the platform-based definitions. While at it, reorder the definitions to have order consistent, too. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-12-06 12:56:51 +00:00
UBNT_CHIP := ar934x
ath79: ubnt-m-xw: Fix factory image flashing using TFTP recovery method Ubiquity allows flashing of unsigned factory images via TFTP recovery method[1]. They claim in airOS v6.0.7 release changelog[2] following: All future airOS versions will be signed in this way and not allow unsigned firmware to be loaded except via TFTP. U-boot bootloader on M-XW devices expects factory image revision version in specific format. On airOS v6.1.7 with `U-Boot 1.1.4-s1039 (May 24 2017 - 15:58:18)` bootloader checks if the revision major(?) number is actually a number, but in currently generated images there's OpenWrt text and so the check fails: Hit any key to stop autoboot: 0 Setting default IP 192.168.1.20 Starting TFTP server... Receiving file from 192.168.1.25:38438 Received 4981148 bytes Firmware check failed! (1) By placing arbitrary correct number first in major version, we make the bootloader happy and we can flash factory images over TFTP again: Received 3735964 bytes Firmware Version: XW.ar934x.v6.0.4-42.r8474-56aa1ac-OpenWrt Setting U-Boot environment variables Un-Protected 1 sectors Erasing Flash.... done Patch provided by AREDN[3] project, tested on Bullet M2 XW (ynezz) and Nanostation M5 XW (ae6xe). 1. https://help.ubnt.com/hc/en-us/articles/204910124-UniFi-TFTP-Recovery-for-Bricked-Access-Points 2. https://dl.ubnt.com/firmwares/XW-fw/v6.0.7/changelog.txt 3. https://github.com/aredn Signed-off-by: Petr Štetiar <ynezz@true.cz>
2018-11-19 20:44:50 +00:00
UBNT_REVISION := 42.$(UBNT_REVISION)
ath79: redistribute UBNT variables in Ubiquiti image Makefile The variables UBNT_BOARD and UBNT_VERSION are defined in the parent Device/ubnt definition and then overwritten for most of the derived platform definitions (e.g. Device/ubnt-wa). Since this mixed use of inheritance and overwriting can be misleading, this moves the variables to the platform-based definitions. While at it, reorder the definitions to have order consistent, too. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-12-06 12:56:51 +00:00
UBNT_TYPE := XW
UBNT_VERSION := 6.0.4
ath79: Add support for Ubiquity Bullet M (XW) CPU: AR9342 SoC RAM: 64 MB DDR2 Flash: 8 MB NOR SPI Ports: 100 MBit (24V PoE in) WLAN: 2.4/5 GHz UART: 1 UART on PCB marked as J1 with 115200 8N1 config LEDs: Power, Ethernet, 4x RSSI LEDs (orange, red, 2x green) Buttons: Reset UART connection details .---------------------------------. | | [ETH] J1 [ANT] | o VCC o RX o TX o GND | `---------------------------------' Flashing instructions A) Serial console, U-Boot and TFTP 1. Connect to serial header J1 on the PCB 2. Power on device and enter U-Boot console 3. Set up TFTP server serving an OpenWrt initramfs build 4. Load initramfs build using the command tftpboot in the U-Boot cli 5. Boot the loaded image using the command bootm 6. Copy squashfs OpenWrt sysupgrade build to the booted device 7. Use mtd to write sysupgrade to partition "firmware" 8. Reboot and enjoy B) Experimental factory image flashing over SSH from airOS v6.1.7 1. You need to flash your UBNT M2HP with airOS v6.1.7 firmware no other airOS version is currently supported 2. git clone https://github.com/true-systems/ubnt-bullet-m2hp-openwrt-flashing 3. cd ubnt-bullet-m2hp-openwrt-flashing 4. make flash-factory FW_OWRT=/path/to/your/openwrt-ath79-generic-ubnt_bullet-m-xw-squashfs-factory.bin Tested only on Bullet M2HP. Signed-off-by: Petr Štetiar <ynezz@true.cz>
2018-11-17 07:01:55 +00:00
endef
ath79: sort device definitions in image/* This applies alphabetic sorting to devices in image/* files. For certain cases, this patch deviates from strict sorting, e.g. to ensure that v10 comes after v9. While at it, fix an indent and remove some useless empty lines. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-08-22 12:34:45 +00:00
define Device/ubnt_acb-isp
$(Device/ubnt)
ath79: rename ATH_SOC to SOC This replaces ATH_SOC by the newly introduced common SOC device variable. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-12-20 00:12:42 +00:00
SOC := qca9533
ath79: sort device definitions in image/* This applies alphabetic sorting to devices in image/* files. For certain cases, this patch deviates from strict sorting, e.g. to ensure that v10 comes after v9. While at it, fix an indent and remove some useless empty lines. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-08-22 12:34:45 +00:00
DEVICE_MODEL := airCube ISP
ath79: redistribute UBNT variables in Ubiquiti image Makefile The variables UBNT_BOARD and UBNT_VERSION are defined in the parent Device/ubnt definition and then overwritten for most of the derived platform definitions (e.g. Device/ubnt-wa). Since this mixed use of inheritance and overwriting can be misleading, this moves the variables to the platform-based definitions. While at it, reorder the definitions to have order consistent, too. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-12-06 12:56:51 +00:00
IMAGE_SIZE := 15744k
ath79: sort device definitions in image/* This applies alphabetic sorting to devices in image/* files. For certain cases, this patch deviates from strict sorting, e.g. to ensure that v10 comes after v9. While at it, fix an indent and remove some useless empty lines. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-08-22 12:34:45 +00:00
UBNT_BOARD := ACB-ISP
UBNT_CHIP := qca9533
ath79: redistribute UBNT variables in Ubiquiti image Makefile The variables UBNT_BOARD and UBNT_VERSION are defined in the parent Device/ubnt definition and then overwritten for most of the derived platform definitions (e.g. Device/ubnt-wa). Since this mixed use of inheritance and overwriting can be misleading, this moves the variables to the platform-based definitions. While at it, reorder the definitions to have order consistent, too. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-12-06 12:56:51 +00:00
UBNT_TYPE := ACB
ath79: generate firmware image for aircube-isp This adds a "factory" image for the aircube-isp devices. Note that the firmware can't be uploaded without prior special preparation. For the most recent instructions on how to do that, visit the OpenWRT wiki page of the Ubiquiti airCube ISP for details: https://openwrt.org/toh/ubiquiti/ubiquiti_aircube_isp Current procedure: With the original firmware 2.5.0 it is possible to upload and execute a script via the configuration. To do that download and unpack the original configuration, adapt uhttpd config to execute another lua handler (placed in the config directory) and pack and upload it again. The lua handler can call a script that mounts an overlayfs and modifies the "fwupdate.real" binary so that an unsigned image is accepted. The overlayfs is necessary because a security system (called tomoyo) doesn't allow binaries in other locations than /sbin/fwupdate.real (and maybe some more) to access the flash when executed via network. A big thanks to Torvald Menningen (Snap) from the OpenWRT forum for finding out how to patch the binary so that it accepts an unsigned image. The current step-by-step procedure is: - Use a version 2.5.0 of the original firmware. This is important because a binary file will be modified. - Download a configuration. - Unpack it (it's just a tar gz file without an ending). - Add the following to uhttpd: `````` config 'uhttpd' 'other' list listen_http 0.0.0.0:8080 list listen_http [::]:8080 option 'home' '/tmp/persistent/config/patch/www' option lua_prefix '/lua' option lua_handler '/tmp/persistent/config/patch/handler.lua' `````` - Create a `patch` subfolder. - Create a `patch/www` subfolder. - Create a `patch/handler.lua` with the following content: `````` function handle_request(env) uhttpd.send("Status: 200 OK\r\n") uhttpd.send("Content-Type: text/plain\r\n\r\n") local command = "/bin/sh /tmp/persistent/config/patch/patch.sh 2>&1" local proc = assert(io.popen(command)) for line in proc:lines() do uhttpd.send(line.."\r\n") end proc:close() end `````` - Create a `patch/patch.sh` with the following content: `````` #!/bin/sh -x set -e set -u set -x UBNTBOX_PATCHED="/tmp/fwupdate.real" MD5FILE="/tmp/patchmd5" cat <<EOF > ${MD5FILE} c33235322da5baca5a7b237c09bc8df1 /sbin/fwupdate.real EOF # check md5 of files that will be patched if ! md5sum -c ${MD5FILE} then echo "******** Error when checking files. Refuse to do anything. ********" exit 0 fi # prepare some overlay functionality LOWERDIR="/tmp/lower_root" mkdir -p ${LOWERDIR} mount -t squashfs -oro /dev/mtdblock3 ${LOWERDIR} overlay_some_path() { PATH_TO_OVERLAY=$1 ALIAS=$2 UPPERDIR="/tmp/over_${ALIAS}" WORKDIR="/tmp/over_${ALIAS}_work" mkdir -p ${UPPERDIR} mkdir -p ${WORKDIR} mount -t overlay -o lowerdir=${LOWERDIR}${PATH_TO_OVERLAY},upperdir=${UPPERDIR},workdir=${WORKDIR} overlay ${PATH_TO_OVERLAY} } # patch the ubntbox binary. overlay_some_path "/sbin" "sbin" echo -en '\x10' | dd of=/sbin/fwupdate.real conv=notrunc bs=1 count=1 seek=24598 echo "******** Done ********" `````` - Repack the configuration. - Upload it via the normal web interface. - Wait about a minute. The webserver should restart. - Now there is a second web server at port 8080 which can call the lua script. Visit the page with a web browser. Link is for example http://192.168.1.1:8080/lua - You should see the output of the script with a "*** Done ***" at the end. Note that the patches are not permanent. If you restart the router you have to re-visit the link (but not re-upload the config). - Now you can upload an unsigned binary via the normal web interface. Signed-off-by: Christian Mauderer <oss@c-mauderer.de>
2019-12-11 13:40:24 +00:00
UBNT_VERSION := 2.5.0
ath79: sort device definitions in image/* This applies alphabetic sorting to devices in image/* files. For certain cases, this patch deviates from strict sorting, e.g. to ensure that v10 comes after v9. While at it, fix an indent and remove some useless empty lines. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-08-22 12:34:45 +00:00
endef
TARGET_DEVICES += ubnt_acb-isp
ath79: add support for Ubiquiti AirRouter Indoor low-power router with 2.4 GHz radio CPU: Atheros AR7241 rev 1 RAM: 32 MB Flash: 8 MB NOR SPI Switch: Atheros AR7240 Ports: 1x WAN, 4x LAN 10/100 Ethernet WLAN: Atheros AR9285 (2.4 GHz) USB: 1x USB2 host port Note: Ethernet WAN/LAN port naming is reversed from ar71xx. WAN is eth0; LAN is eth1.1. UART settings: 115200, 8N1 LEDs +-------------------------- | | | | | | | | VCC | x x RX | * x | x x | x x TX | * x GND | * x | | | | +-------------------------- ETHERNET PORTS Installation from Ubiquiti firmware, is as for other ubnt-xm AirOs devices. Signed-off-by: Russell Senior <russell@personaltelco.net>
2018-11-26 22:28:00 +00:00
define Device/ubnt_airrouter
$(Device/ubnt-xm)
ath79: split DEVICE_TITLE in multiple variables This allows the definition of DEVICE_VENDOR, DEVICE_MODEL and DEVICE_VARIANT. All three are merged together to look the same as the current DEVICE_TITLE. Also, if DEVICE_TITLE is set it's directly used as a *fallback* for devices which weren't upgraded yet. This is based on the work of @sudhanshu16. The motivation is to create JSON files based on provided metadata, needing clear differentiation between vendor, model and revision. Signed-off-by: Paul Spooren <mail@aparcar.org>
2019-06-16 19:34:46 +00:00
DEVICE_MODEL := AirRouter
ath79: add support for Ubiquiti AirRouter Indoor low-power router with 2.4 GHz radio CPU: Atheros AR7241 rev 1 RAM: 32 MB Flash: 8 MB NOR SPI Switch: Atheros AR7240 Ports: 1x WAN, 4x LAN 10/100 Ethernet WLAN: Atheros AR9285 (2.4 GHz) USB: 1x USB2 host port Note: Ethernet WAN/LAN port naming is reversed from ar71xx. WAN is eth0; LAN is eth1.1. UART settings: 115200, 8N1 LEDs +-------------------------- | | | | | | | | VCC | x x RX | * x | x x | x x TX | * x GND | * x | | | | +-------------------------- ETHERNET PORTS Installation from Ubiquiti firmware, is as for other ubnt-xm AirOs devices. Signed-off-by: Russell Senior <russell@personaltelco.net>
2018-11-26 22:28:00 +00:00
SUPPORTED_DEVICES += airrouter
endef
TARGET_DEVICES += ubnt_airrouter
ath79: fix dts files Add the SoC compatible to the individual dts files. Rename the dts files to match the common pattern. Remove dts files wich aren't used and no image in ar71xx exists. Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-05-08 05:22:38 +00:00
define Device/ubnt_bullet-m
ath79: add new OF only target for QCA MIPS silicon This target aims to replace ar71xx mid-term. The big part that is still missing is making the MMIO/AHB wifi work using OF. NAND and mikrotik subtargets will follow. Signed-off-by: John Crispin <john@phrozen.org>
2018-05-06 08:20:11 +00:00
$(Device/ubnt-xm)
ath79: split DEVICE_TITLE in multiple variables This allows the definition of DEVICE_VENDOR, DEVICE_MODEL and DEVICE_VARIANT. All three are merged together to look the same as the current DEVICE_TITLE. Also, if DEVICE_TITLE is set it's directly used as a *fallback* for devices which weren't upgraded yet. This is based on the work of @sudhanshu16. The motivation is to create JSON files based on provided metadata, needing clear differentiation between vendor, model and revision. Signed-off-by: Paul Spooren <mail@aparcar.org>
2019-06-16 19:34:46 +00:00
DEVICE_MODEL := Bullet-M
ath79: include rssileds package for ubnt devices with LEDs Some Ubiquiti devices had the RSSI LEDs configured in 01_leds but were missing the rssileds package, while others that don't have RSSI LEDS had the package included. This commit includes the rssileds package only for those devices that need it. Tested on a NanoStation M XW. Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
2019-11-13 15:18:59 +00:00
DEVICE_PACKAGES += rssileds
ath79: add and enforce image metadata Add metadata to images and make the metdata mandatory. Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-05-07 20:41:04 +00:00
SUPPORTED_DEVICES += bullet-m
ath79: add new OF only target for QCA MIPS silicon This target aims to replace ar71xx mid-term. The big part that is still missing is making the MMIO/AHB wifi work using OF. NAND and mikrotik subtargets will follow. Signed-off-by: John Crispin <john@phrozen.org>
2018-05-06 08:20:11 +00:00
endef
ath79: fix dts files Add the SoC compatible to the individual dts files. Rename the dts files to match the common pattern. Remove dts files wich aren't used and no image in ar71xx exists. Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-05-08 05:22:38 +00:00
TARGET_DEVICES += ubnt_bullet-m
ath79: add new OF only target for QCA MIPS silicon This target aims to replace ar71xx mid-term. The big part that is still missing is making the MMIO/AHB wifi work using OF. NAND and mikrotik subtargets will follow. Signed-off-by: John Crispin <john@phrozen.org>
2018-05-06 08:20:11 +00:00
ath79: Add support for Ubiquity Bullet M (XW) CPU: AR9342 SoC RAM: 64 MB DDR2 Flash: 8 MB NOR SPI Ports: 100 MBit (24V PoE in) WLAN: 2.4/5 GHz UART: 1 UART on PCB marked as J1 with 115200 8N1 config LEDs: Power, Ethernet, 4x RSSI LEDs (orange, red, 2x green) Buttons: Reset UART connection details .---------------------------------. | | [ETH] J1 [ANT] | o VCC o RX o TX o GND | `---------------------------------' Flashing instructions A) Serial console, U-Boot and TFTP 1. Connect to serial header J1 on the PCB 2. Power on device and enter U-Boot console 3. Set up TFTP server serving an OpenWrt initramfs build 4. Load initramfs build using the command tftpboot in the U-Boot cli 5. Boot the loaded image using the command bootm 6. Copy squashfs OpenWrt sysupgrade build to the booted device 7. Use mtd to write sysupgrade to partition "firmware" 8. Reboot and enjoy B) Experimental factory image flashing over SSH from airOS v6.1.7 1. You need to flash your UBNT M2HP with airOS v6.1.7 firmware no other airOS version is currently supported 2. git clone https://github.com/true-systems/ubnt-bullet-m2hp-openwrt-flashing 3. cd ubnt-bullet-m2hp-openwrt-flashing 4. make flash-factory FW_OWRT=/path/to/your/openwrt-ath79-generic-ubnt_bullet-m-xw-squashfs-factory.bin Tested only on Bullet M2HP. Signed-off-by: Petr Štetiar <ynezz@true.cz>
2018-11-17 07:01:55 +00:00
define Device/ubnt_bullet-m-xw
$(Device/ubnt-xw)
ath79: split DEVICE_TITLE in multiple variables This allows the definition of DEVICE_VENDOR, DEVICE_MODEL and DEVICE_VARIANT. All three are merged together to look the same as the current DEVICE_TITLE. Also, if DEVICE_TITLE is set it's directly used as a *fallback* for devices which weren't upgraded yet. This is based on the work of @sudhanshu16. The motivation is to create JSON files based on provided metadata, needing clear differentiation between vendor, model and revision. Signed-off-by: Paul Spooren <mail@aparcar.org>
2019-06-16 19:34:46 +00:00
DEVICE_MODEL := Bullet-M
ath79: include rssileds package for ubnt devices with LEDs Some Ubiquiti devices had the RSSI LEDs configured in 01_leds but were missing the rssileds package, while others that don't have RSSI LEDS had the package included. This commit includes the rssileds package only for those devices that need it. Tested on a NanoStation M XW. Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
2019-11-13 15:18:59 +00:00
DEVICE_PACKAGES += rssileds
ath79: Add support for Ubiquity Bullet M (XW) CPU: AR9342 SoC RAM: 64 MB DDR2 Flash: 8 MB NOR SPI Ports: 100 MBit (24V PoE in) WLAN: 2.4/5 GHz UART: 1 UART on PCB marked as J1 with 115200 8N1 config LEDs: Power, Ethernet, 4x RSSI LEDs (orange, red, 2x green) Buttons: Reset UART connection details .---------------------------------. | | [ETH] J1 [ANT] | o VCC o RX o TX o GND | `---------------------------------' Flashing instructions A) Serial console, U-Boot and TFTP 1. Connect to serial header J1 on the PCB 2. Power on device and enter U-Boot console 3. Set up TFTP server serving an OpenWrt initramfs build 4. Load initramfs build using the command tftpboot in the U-Boot cli 5. Boot the loaded image using the command bootm 6. Copy squashfs OpenWrt sysupgrade build to the booted device 7. Use mtd to write sysupgrade to partition "firmware" 8. Reboot and enjoy B) Experimental factory image flashing over SSH from airOS v6.1.7 1. You need to flash your UBNT M2HP with airOS v6.1.7 firmware no other airOS version is currently supported 2. git clone https://github.com/true-systems/ubnt-bullet-m2hp-openwrt-flashing 3. cd ubnt-bullet-m2hp-openwrt-flashing 4. make flash-factory FW_OWRT=/path/to/your/openwrt-ath79-generic-ubnt_bullet-m-xw-squashfs-factory.bin Tested only on Bullet M2HP. Signed-off-by: Petr Štetiar <ynezz@true.cz>
2018-11-17 07:01:55 +00:00
SUPPORTED_DEVICES += bullet-m-xw
endef
TARGET_DEVICES += ubnt_bullet-m-xw
ath79: add support for Ubiquiti EdgeSwitch/ToughSwitch 5XP The Ubiquiti ToughSwitch 5XP is a 5-port PoE Gigabit switch with a single Fast-Ethernet management port. It supports both 24V passive PoE out on all five ports. Flash: 8 MB RAM: 64 MB SoC: AR7242 Switch: ar8327 USB: 1x USB 2.0 Ethernet: 5x GbE, 1x FE Installation of the firmware is possible either via serial + tftpboot or the factory firmware update function via webinterface. By default the single Fast-Ethernet port labeled "MGMT" is configured as the WAN port. Thus access to the device is only possible via the five switch ports. Serial: 3v3 115200 8n1 The serial header is located in the lower left corner of the switches PCB: ``` | | | | o | o RX | o TX | o GND | | ++ +-++-+ ++ ++ + +--+ ++ +--++--++--+ ``` Signed-off-by: Tobias Schramm <tobleminer@gmail.com> [remove ubnt,sw compatible - fix spelling - wrap commit message - remove superfluous phy-mode property] Signed-off-by: David Bauer <mail@david-bauer.net>
2020-01-01 09:01:48 +00:00
define Device/ubnt_edgeswitch-5xp
$(Device/ubnt-sw)
DEVICE_MODEL := EdgeSwitch 5XP
endef
TARGET_DEVICES += ubnt_edgeswitch-5xp
ath79: add support for Ubiquiti ToughSwitch/EdgeSwitch 8XP Flash: 8 MB RAM: 64 MB SoC: AR7242 Switch: bcm53128 USB: 1x USB 2.0 Ethernet: 8x GbE, 1x FE The Ubiquiti ToughSwitch 8XP is a 8-port PoE Gigabit switch with a single Fast-Ethernet management port. It supports both 24V passive PoE and 48V 802.11af/at PoE out on all eight ports. By default the single Fast-Ethernet port labeled "MGMT" is configured as the WAN port. Thus access to the device is only possible via the eight switch ports. Installation of the firware is possible either via serial + tftpboot or the factory firmware update function via webinterface. Serial: 3v3 115200 8n1 The serial header is located in the lower left corner of the switches PCB: | | | | o | o RX | o TX | o GND | | ++ +-++-+ ++ ++ + +--+ ++ +--++--++--+ Signed-off-by: Tobias Schramm <tobleminer@gmail.com> [fix whitespace issue] Signed-off-by: David Bauer <mail@david-bauer.net>
2019-12-03 21:48:35 +00:00
define Device/ubnt_edgeswitch-8xp
$(Device/ubnt-sw)
DEVICE_MODEL := EdgeSwitch 8XP
DEVICE_PACKAGES += switch-bcm53xx-mdio
endef
TARGET_DEVICES += ubnt_edgeswitch-8xp
ath79: Add support for Ubiquiti LiteAP ac (LAP-120) This commit adds support for the Ubiquiti LiteAP ac (LAP-120), an outdoor 5 GHz AC access point with an integrated 120° 16 dBi antenna. The device was previously known as LiteBeam AP ac but was later rebranded. CPU: Atheros AR9342 SoC RAM: 64 MB DDR2 Flash: 16 MB NOR SPI Ports: 1 GbE port (PoE in) WLAN: 5 GHz QCA899X (PCI) The integrated QCA899X is a Ubiquiti branded part with modified vendor and product id (0777:11ac9). It is very similar to the NanoStation loco AC, except for the 2.4 GHz management radio (missing here). Installation procedure is the same as the NanoStation [loco] AC: 1. Connect to serial header on device 2. Power on device and enter uboot console 3. Set up tftp server serving an openwrt initramfs build 4. Load initramfs build using the command tftpboot in the uboot cli 5. Boot the loaded image using the command bootm 6. Copy squashfs openwrt sysupgrade build to the booted device 7. Use mtd to write sysupgrade to partition "firmware" 8. Reboot and enjoy Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
2018-09-19 12:17:35 +00:00
define Device/ubnt_lap-120
$(Device/ubnt-wa)
ath79: split DEVICE_TITLE in multiple variables This allows the definition of DEVICE_VENDOR, DEVICE_MODEL and DEVICE_VARIANT. All three are merged together to look the same as the current DEVICE_TITLE. Also, if DEVICE_TITLE is set it's directly used as a *fallback* for devices which weren't upgraded yet. This is based on the work of @sudhanshu16. The motivation is to create JSON files based on provided metadata, needing clear differentiation between vendor, model and revision. Signed-off-by: Paul Spooren <mail@aparcar.org>
2019-06-16 19:34:46 +00:00
DEVICE_MODEL := LiteAP ac
DEVICE_VARIANT := LAP-120
ath79: use ath10k-ct-smallbuffers for 64 MiB devices Signed-off-by: Paul Fertser <fercerpav@gmail.com>
2019-12-22 20:05:13 +00:00
DEVICE_PACKAGES += kmod-ath10k-ct-smallbuffers ath10k-firmware-qca988x-ct
ath79: Add support for Ubiquiti LiteAP ac (LAP-120) This commit adds support for the Ubiquiti LiteAP ac (LAP-120), an outdoor 5 GHz AC access point with an integrated 120° 16 dBi antenna. The device was previously known as LiteBeam AP ac but was later rebranded. CPU: Atheros AR9342 SoC RAM: 64 MB DDR2 Flash: 16 MB NOR SPI Ports: 1 GbE port (PoE in) WLAN: 5 GHz QCA899X (PCI) The integrated QCA899X is a Ubiquiti branded part with modified vendor and product id (0777:11ac9). It is very similar to the NanoStation loco AC, except for the 2.4 GHz management radio (missing here). Installation procedure is the same as the NanoStation [loco] AC: 1. Connect to serial header on device 2. Power on device and enter uboot console 3. Set up tftp server serving an openwrt initramfs build 4. Load initramfs build using the command tftpboot in the uboot cli 5. Boot the loaded image using the command bootm 6. Copy squashfs openwrt sysupgrade build to the booted device 7. Use mtd to write sysupgrade to partition "firmware" 8. Reboot and enjoy Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
2018-09-19 12:17:35 +00:00
endef
TARGET_DEVICES += ubnt_lap-120
ath79: add support for Ubiquiti LiteBeam AC Gen2 Hardware: * SoC: Atheros AR9342-BL1A * RAM: 64MB DDR2 (Winbond W9751G6KB-25) * Flash: 16MB SPI NOR (Macronix MX25L12835FZ2I-10G) * Ethernet: 1x 10/100/1000 Mbps (Atheros AR8035-A) with 24V PoE support * Wifi 2.4GHz: Atheros AR9340 v2 * WiFi 5GHz: Ubiquiti U-AME-G1-BR4A (rebranded QCA988X v2) * LEDs: 1x Power, 1x Ethernet * Buttons: 1x Reset * UART: 1x TTL 115200n8, 3.3V RX TX GND, 3.3V pin closest to RJ45 port The LEDs do not seem to be connected to any GPIO, so there is currently no way to control them. Installation via U-Boot, TFTP and serial console: * Configure your TFTP server with IP 192.168.1.254 * Connect serial console and power up the device * Hit any key to stop autoboot * tftpboot 0x81000000 openwrt-ath79-generic-ubnt_litebeam-ac-gen2-initramfs-kernel.bin * bootm 0x81000000 * copy openwrt-ath79-generic-ubnt_litebeam-ac-gen2-squashfs-sysupgrade.bin to /tmp * sysupgrade /tmp/openwrt-ath79-generic-ubnt_litebeam-ac-gen2-squashfs-sysupgrade.bin Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be> Acked-by: Petr Štetiar <ynezz@true.cz> Acked-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-04-12 17:21:58 +00:00
define Device/ubnt_litebeam-ac-gen2
$(Device/ubnt-wa)
DEVICE_MODEL := LiteBeam AC
DEVICE_VARIANT := Gen2
ath79: use ath10k-ct-smallbuffers for 64 MiB devices Signed-off-by: Paul Fertser <fercerpav@gmail.com>
2019-12-22 20:05:13 +00:00
DEVICE_PACKAGES := kmod-ath10k-ct-smallbuffers ath10k-firmware-qca988x-ct
ath79: add support for Ubiquiti LiteBeam AC Gen2 Hardware: * SoC: Atheros AR9342-BL1A * RAM: 64MB DDR2 (Winbond W9751G6KB-25) * Flash: 16MB SPI NOR (Macronix MX25L12835FZ2I-10G) * Ethernet: 1x 10/100/1000 Mbps (Atheros AR8035-A) with 24V PoE support * Wifi 2.4GHz: Atheros AR9340 v2 * WiFi 5GHz: Ubiquiti U-AME-G1-BR4A (rebranded QCA988X v2) * LEDs: 1x Power, 1x Ethernet * Buttons: 1x Reset * UART: 1x TTL 115200n8, 3.3V RX TX GND, 3.3V pin closest to RJ45 port The LEDs do not seem to be connected to any GPIO, so there is currently no way to control them. Installation via U-Boot, TFTP and serial console: * Configure your TFTP server with IP 192.168.1.254 * Connect serial console and power up the device * Hit any key to stop autoboot * tftpboot 0x81000000 openwrt-ath79-generic-ubnt_litebeam-ac-gen2-initramfs-kernel.bin * bootm 0x81000000 * copy openwrt-ath79-generic-ubnt_litebeam-ac-gen2-squashfs-sysupgrade.bin to /tmp * sysupgrade /tmp/openwrt-ath79-generic-ubnt_litebeam-ac-gen2-squashfs-sysupgrade.bin Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be> Acked-by: Petr Štetiar <ynezz@true.cz> Acked-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-04-12 17:21:58 +00:00
endef
TARGET_DEVICES += ubnt_litebeam-ac-gen2
ath79: Add support for Ubiquiti NanoBeam AC The NanoBeam is a small AR9342 based directional 5 GHz AC CPE with hardware almost identical to the Ubiquiti NanoStation AC loco. Over the NanoStation AC loco it has 5 additional LEDs. Four of those LEDs are used as rssi indicators, the fifth LED is used as an ethernet link/activity indicator. CPU: Atheros AR9342 SoC RAM: 64 MB DDR2 Flash: 16 MB NOR SPI WLAN: QCA988X Ports: 1x GbE Flashing procedure is identical to the NanoStation AC loco and can be performed either via serial or the factory firmware upgrade. Serial flashing: 1. Connect to serial header on device (8N1 115200) 2. Power on device and enter uboot console 3. Set up tftp server serving an openwrt initramfs build 4. Load initramfs build using the command tftpboot in the uboot cli 5. Boot the loaded image using the command bootm 6. Copy squashfs openwrt sysupgrade build to the booted device 7. Use mtd to write sysupgrade to partition "firmware" 8. Reboot and enjoy Flashing through factory firmware: 1. Ensure firmware version v8.5.0.36727 is installed. Up/downgrade to this exact version. 2. Patch fwupdate.real binary using `hexdump -Cv /bin/ubntbox | sed 's/14 40 fe fe/00 00 00 00/g' | hexdump -R > /tmp/fwupdate.real` 3. Make the patched fwupdate.real binary executable using `chmod +x /tmp/fwupdate.real` 4. Copy the squashfs factory image to /tmp on the device 5. Flash OpenWRT using `/tmp/fwupdate.real -m <squashfs-factory image>` 6. Wait for the device to reboot Thanks to @cybermaus for testing! Tested-by: Maurits van Dueren den Hollander <cybermaus@gmail.com> Signed-off-by: Tobias Schramm <tobleminer@gmail.com>
2019-01-08 14:27:57 +00:00
define Device/ubnt_nanobeam-ac
$(Device/ubnt-wa)
ath79: split DEVICE_TITLE in multiple variables This allows the definition of DEVICE_VENDOR, DEVICE_MODEL and DEVICE_VARIANT. All three are merged together to look the same as the current DEVICE_TITLE. Also, if DEVICE_TITLE is set it's directly used as a *fallback* for devices which weren't upgraded yet. This is based on the work of @sudhanshu16. The motivation is to create JSON files based on provided metadata, needing clear differentiation between vendor, model and revision. Signed-off-by: Paul Spooren <mail@aparcar.org>
2019-06-16 19:34:46 +00:00
DEVICE_MODEL := NanoBeam AC
ath79: use ath10k-ct-smallbuffers for 64 MiB devices Signed-off-by: Paul Fertser <fercerpav@gmail.com>
2019-12-22 20:05:13 +00:00
DEVICE_PACKAGES += kmod-ath10k-ct-smallbuffers ath10k-firmware-qca988x-ct rssileds
ath79: Add support for Ubiquiti NanoBeam AC The NanoBeam is a small AR9342 based directional 5 GHz AC CPE with hardware almost identical to the Ubiquiti NanoStation AC loco. Over the NanoStation AC loco it has 5 additional LEDs. Four of those LEDs are used as rssi indicators, the fifth LED is used as an ethernet link/activity indicator. CPU: Atheros AR9342 SoC RAM: 64 MB DDR2 Flash: 16 MB NOR SPI WLAN: QCA988X Ports: 1x GbE Flashing procedure is identical to the NanoStation AC loco and can be performed either via serial or the factory firmware upgrade. Serial flashing: 1. Connect to serial header on device (8N1 115200) 2. Power on device and enter uboot console 3. Set up tftp server serving an openwrt initramfs build 4. Load initramfs build using the command tftpboot in the uboot cli 5. Boot the loaded image using the command bootm 6. Copy squashfs openwrt sysupgrade build to the booted device 7. Use mtd to write sysupgrade to partition "firmware" 8. Reboot and enjoy Flashing through factory firmware: 1. Ensure firmware version v8.5.0.36727 is installed. Up/downgrade to this exact version. 2. Patch fwupdate.real binary using `hexdump -Cv /bin/ubntbox | sed 's/14 40 fe fe/00 00 00 00/g' | hexdump -R > /tmp/fwupdate.real` 3. Make the patched fwupdate.real binary executable using `chmod +x /tmp/fwupdate.real` 4. Copy the squashfs factory image to /tmp on the device 5. Flash OpenWRT using `/tmp/fwupdate.real -m <squashfs-factory image>` 6. Wait for the device to reboot Thanks to @cybermaus for testing! Tested-by: Maurits van Dueren den Hollander <cybermaus@gmail.com> Signed-off-by: Tobias Schramm <tobleminer@gmail.com>
2019-01-08 14:27:57 +00:00
endef
TARGET_DEVICES += ubnt_nanobeam-ac
ath79: Add support for Ubiquiti Nanostation AC 5 GHz AC wireless outdoor PoE CPE with internal 2.4 GHz management radio CPU: Atheros AR9342 SoC RAM: 64 MB DDR2 Flash: 16 MB NOR SPI Switch: QCA8334 Ports: 2 GbE ports (1x PoE in, 1x PoE passthrough) WLAN: 5 GHz QCA899X (PCI) and 2.4 GHZ AR9342 Successor to the old NanoStation M5 with AC wireless. The integrated QCA899X is a Ubiquiti branded part with modified vendor and product id (0777:11ac9). Serial Serial settings: 115200, 8N1 * = plated through hole 0 = nylon screw [Top of device] +--------------------------+ | [label] | | 0 | | 0 | | [ubnt] | | [logo] 3V3 * | | TX * | | RX * | | GND * | | | | * | | * | | * | | * | | 0 | | 0 | | | | | Installation 1. Connect to serial header on device 2. Power on device and enter uboot console 3. Set up tftp server serving an openwrt initramfs build 4. Load initramfs build using the command tftpboot in the uboot cli 5. Boot the loaded image using the command bootm 6. Copy squashfs openwrt sysupgrade build to the booted device 7. Use mtd to write sysupgrade to partition "firmware" 8. Reboot and enjoy Signed-off-by: Tobias Schramm <tobleminer@gmail.com>
2018-09-04 00:08:01 +00:00
define Device/ubnt_nanostation-ac
$(Device/ubnt-wa)
ath79: split DEVICE_TITLE in multiple variables This allows the definition of DEVICE_VENDOR, DEVICE_MODEL and DEVICE_VARIANT. All three are merged together to look the same as the current DEVICE_TITLE. Also, if DEVICE_TITLE is set it's directly used as a *fallback* for devices which weren't upgraded yet. This is based on the work of @sudhanshu16. The motivation is to create JSON files based on provided metadata, needing clear differentiation between vendor, model and revision. Signed-off-by: Paul Spooren <mail@aparcar.org>
2019-06-16 19:34:46 +00:00
DEVICE_MODEL := Nanostation AC
ath79: use ath10k-ct-smallbuffers for 64 MiB devices Signed-off-by: Paul Fertser <fercerpav@gmail.com>
2019-12-22 20:05:13 +00:00
DEVICE_PACKAGES += kmod-ath10k-ct-smallbuffers ath10k-firmware-qca988x-ct rssileds
ath79: Add support for Ubiquiti Nanostation AC 5 GHz AC wireless outdoor PoE CPE with internal 2.4 GHz management radio CPU: Atheros AR9342 SoC RAM: 64 MB DDR2 Flash: 16 MB NOR SPI Switch: QCA8334 Ports: 2 GbE ports (1x PoE in, 1x PoE passthrough) WLAN: 5 GHz QCA899X (PCI) and 2.4 GHZ AR9342 Successor to the old NanoStation M5 with AC wireless. The integrated QCA899X is a Ubiquiti branded part with modified vendor and product id (0777:11ac9). Serial Serial settings: 115200, 8N1 * = plated through hole 0 = nylon screw [Top of device] +--------------------------+ | [label] | | 0 | | 0 | | [ubnt] | | [logo] 3V3 * | | TX * | | RX * | | GND * | | | | * | | * | | * | | * | | 0 | | 0 | | | | | Installation 1. Connect to serial header on device 2. Power on device and enter uboot console 3. Set up tftp server serving an openwrt initramfs build 4. Load initramfs build using the command tftpboot in the uboot cli 5. Boot the loaded image using the command bootm 6. Copy squashfs openwrt sysupgrade build to the booted device 7. Use mtd to write sysupgrade to partition "firmware" 8. Reboot and enjoy Signed-off-by: Tobias Schramm <tobleminer@gmail.com>
2018-09-04 00:08:01 +00:00
endef
TARGET_DEVICES += ubnt_nanostation-ac
ath79: Add support for Ubiquiti NanoStation AC loco Atheros AR9342, 16 MB flash, 64 MB RAM Successor to the old NanoStation M5 loco with AC wireless. Includes a mac80211 patch for ath10k_pci because Ubiquiti uses a Ubiquiti branded and customized QCA988X with vendor id 0777 and device id 11ac for AC wireless. Installation 1. Connect to serial header on device (8N1 115200) 2. Power on device and enter uboot console 3. Set up tftp server serving an openwrt initramfs build 4. Load initramfs build using the command tftpboot in the uboot cli 5. Boot the loaded image using the command bootm 6. Copy squashfs openwrt sysupgrade build to the booted device 7. Use mtd to write sysupgrade to partition "firmware" 8. Reboot and enjoy Signed-off-by: Tobias Schramm <tobleminer@gmail.com>
2018-01-23 10:36:41 +00:00
define Device/ubnt_nanostation-ac-loco
$(Device/ubnt-wa)
ath79: split DEVICE_TITLE in multiple variables This allows the definition of DEVICE_VENDOR, DEVICE_MODEL and DEVICE_VARIANT. All three are merged together to look the same as the current DEVICE_TITLE. Also, if DEVICE_TITLE is set it's directly used as a *fallback* for devices which weren't upgraded yet. This is based on the work of @sudhanshu16. The motivation is to create JSON files based on provided metadata, needing clear differentiation between vendor, model and revision. Signed-off-by: Paul Spooren <mail@aparcar.org>
2019-06-16 19:34:46 +00:00
DEVICE_MODEL := Nanostation AC loco
ath79: use ath10k-ct-smallbuffers for 64 MiB devices Signed-off-by: Paul Fertser <fercerpav@gmail.com>
2019-12-22 20:05:13 +00:00
DEVICE_PACKAGES += kmod-ath10k-ct-smallbuffers ath10k-firmware-qca988x-ct
ath79: Add support for Ubiquiti NanoStation AC loco Atheros AR9342, 16 MB flash, 64 MB RAM Successor to the old NanoStation M5 loco with AC wireless. Includes a mac80211 patch for ath10k_pci because Ubiquiti uses a Ubiquiti branded and customized QCA988X with vendor id 0777 and device id 11ac for AC wireless. Installation 1. Connect to serial header on device (8N1 115200) 2. Power on device and enter uboot console 3. Set up tftp server serving an openwrt initramfs build 4. Load initramfs build using the command tftpboot in the uboot cli 5. Boot the loaded image using the command bootm 6. Copy squashfs openwrt sysupgrade build to the booted device 7. Use mtd to write sysupgrade to partition "firmware" 8. Reboot and enjoy Signed-off-by: Tobias Schramm <tobleminer@gmail.com>
2018-01-23 10:36:41 +00:00
endef
TARGET_DEVICES += ubnt_nanostation-ac-loco
ath79: add support for Ubiquiti Nanostation Loco M (XM) This adds support for the Ubiquiti Nanostation Loco M (XM), which has the same board/LEDs as the Bullet M XM, but different case and antennas. Specifications: - AR7241 SoC @ 400 MHz - 32 MB RAM - 8 MB SPI flash - 1x 10/100 Mbps Ethernet, 24 Vdc PoE-in - NS Loco M2: built-in antenna: 8 dBi; AR9287 - NS Loco M5: built-in antenna: 13 dBi; 2T2R 5 GHz radio - POWER/LAN green LEDs - 4x RSSI LEDs (red, orange, green, green) - UART (115200 8N1) on PCB Flashing via WebUI: Upload the factory image via the stock firmware web UI. Note that only certain firmware versions accept unsigned images. Refer to the device's Wiki page for further information. Flashing via TFTP: Same procedure as other NanoStation M boards. - Use a pointy tool (e.g., pen cap, paper clip) and keep the reset button on the device or on the PoE supply pressed - Power on the device via PoE (keep reset button pressed) - Keep pressing until LEDs flash alternatively LED1+LED3 => LED2+LED4 => LED1+LED3, etc. - Release reset button - The device starts a TFTP server at 192.168.1.20 - Set a static IP on the computer (e.g., 192.168.1.21/24) - Upload via tftp the factory image: $ tftp 192.168.1.20 tftp> bin tftp> trace tftp> put openwrt-ath79-generic-xxxxx-ubnt_nanostation-loco-m-squashfs-factory.bin Tested on NanoStation Loco M2. Signed-off-by: Sven Roederer <freifunk@it-solutions.geroedel.de> Co-developed-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-02-17 11:22:53 +00:00
define Device/ubnt_nanostation-loco-m
$(Device/ubnt-xm)
DEVICE_MODEL := Nanostation Loco M
DEVICE_PACKAGES += rssileds
SUPPORTED_DEVICES += bullet-m
endef
TARGET_DEVICES += ubnt_nanostation-loco-m
ath79: add support for Ubiquiti NanoStation Loco M (XW) This commit adds support for the NanoStation Loco M2/M5 XW devices on the ath79 target (support was long ago available on ar71xx). Specifications: - AR9342 SoC @ 535 MHz - 64 MB RAM - 8 MB SPI flash - 1x 10/100 Mbps Ethernet, 24 Vdc PoE-in - AR8032 switch - 2T2R 5 GHz radio, 22 dBm - 13 dBi built-in antenna - POWER/LAN green LEDs - 4x RSSI LEDs (red, orange, green, green) - UART (115200 8N1) on PCB Flashing via TFTP: - Use a pointy tool (e.g., pen cap, paper clip) and keep the reset button on the device or on the PoE supply pressed - Power on the device via PoE (keep reset button pressed) - Keep pressing until LEDs flash alternatively LED1+LED3 => LED2+LED4 => LED1+LED3, etc. - Release reset button - The device starts a TFTP server at 192.168.1.20 - Set a static IP on the computer (e.g., 192.168.1.21/24) - Upload via tftp the factory image: $ tftp 192.168.1.20 tftp> bin tftp> trace tftp> put openwrt-ath79-generic-xxxxx-ubnt_nanostation-loco-m-xw-squashfs-factory.bin Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
2019-09-18 13:17:56 +00:00
define Device/ubnt_nanostation-loco-m-xw
$(Device/ubnt-xw)
DEVICE_MODEL := Nanostation Loco M
DEVICE_PACKAGES += rssileds
SUPPORTED_DEVICES += loco-m-xw
endef
TARGET_DEVICES += ubnt_nanostation-loco-m-xw
ath79: sort device definitions in image/* This applies alphabetic sorting to devices in image/* files. For certain cases, this patch deviates from strict sorting, e.g. to ensure that v10 comes after v9. While at it, fix an indent and remove some useless empty lines. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-08-22 12:34:45 +00:00
define Device/ubnt_nanostation-m
$(Device/ubnt-xm)
DEVICE_MODEL := Nanostation M
ath79: include rssileds package for ubnt devices with LEDs Some Ubiquiti devices had the RSSI LEDs configured in 01_leds but were missing the rssileds package, while others that don't have RSSI LEDS had the package included. This commit includes the rssileds package only for those devices that need it. Tested on a NanoStation M XW. Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
2019-11-13 15:18:59 +00:00
DEVICE_PACKAGES += rssileds
ath79: fix SUPPORTED_DEVICES for ubnt_nanostation-m The ar71xx images for the Ubiquiti NanoStation M (XM) devices use "nanostation-m" as board name, but the ath79 images are only compatible with the "nano-m" board name, so sysupgrade complains. By changing this additional supported device, sysupgrade smoothly upgrades from ar71xx to ath79. Ref: openwrt#2418 Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-10-04 12:44:07 +00:00
SUPPORTED_DEVICES += nanostation-m
ath79: sort device definitions in image/* This applies alphabetic sorting to devices in image/* files. For certain cases, this patch deviates from strict sorting, e.g. to ensure that v10 comes after v9. While at it, fix an indent and remove some useless empty lines. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-08-22 12:34:45 +00:00
endef
TARGET_DEVICES += ubnt_nanostation-m
define Device/ubnt_nanostation-m-xw
$(Device/ubnt-xw)
DEVICE_MODEL := Nanostation M
ath79: include rssileds package for ubnt devices with LEDs Some Ubiquiti devices had the RSSI LEDs configured in 01_leds but were missing the rssileds package, while others that don't have RSSI LEDS had the package included. This commit includes the rssileds package only for those devices that need it. Tested on a NanoStation M XW. Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
2019-11-13 15:18:59 +00:00
DEVICE_PACKAGES += rssileds
ath79: sort device definitions in image/* This applies alphabetic sorting to devices in image/* files. For certain cases, this patch deviates from strict sorting, e.g. to ensure that v10 comes after v9. While at it, fix an indent and remove some useless empty lines. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-08-22 12:34:45 +00:00
SUPPORTED_DEVICES += nanostation-m-xw
endef
TARGET_DEVICES += ubnt_nanostation-m-xw
ath79: add support for Ubiquiti Picostation M (XM) This adds support for the Ubiquiti Picostation M (XM), which has the same board/LEDs as the Bullet M XM, but different case and antennas. Specifications: - AR7241 SoC @ 400 MHz - 32 MB RAM - 8 MB SPI flash - 1x 10/100 Mbps Ethernet, 24 Vdc PoE-in - External antenna: 5 dBi (USA), 2 dBi (EU) - POWER/LAN green LEDs - 4x RSSI LEDs (red, orange, green, green) - UART (115200 8N1) on PCB Flashing via WebUI: Upload the factory image via the stock firmware web UI. Attention: airOS firmware versions >= 5.6 have a new bootloader with an incompatible partition table! Please downgrade to <= 5.5 _before_ flashing OpenWrt! Refer to the device's Wiki page for further information. Flashing via TFTP: Same procedure as other NanoStation M boards. - Use a pointy tool (e.g., pen cap, paper clip) and keep the reset button on the device or on the PoE supply pressed - Power on the device via PoE (keep reset button pressed) - Keep pressing until LEDs flash alternatively LED1+LED3 => LED2+LED4 => LED1+LED3, etc. - Release reset button - The device starts a TFTP server at 192.168.1.20 - Set a static IP on the computer (e.g., 192.168.1.21/24) - Upload via tftp the factory image: $ tftp 192.168.1.20 tftp> bin tftp> trace tftp> put openwrt-ath79-generic-xxxxx-ubnt_picostation-m-squashfs-factory.bin Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-02-17 23:08:18 +00:00
define Device/ubnt_picostation-m
$(Device/ubnt-xm)
DEVICE_MODEL := Picostation M
DEVICE_PACKAGES += rssileds
SUPPORTED_DEVICES += bullet-m
endef
TARGET_DEVICES += ubnt_picostation-m
ath79: sort device definitions in image/* This applies alphabetic sorting to devices in image/* files. For certain cases, this patch deviates from strict sorting, e.g. to ensure that v10 comes after v9. While at it, fix an indent and remove some useless empty lines. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-08-22 12:34:45 +00:00
define Device/ubnt_rocket-m
$(Device/ubnt-xm)
DEVICE_MODEL := Rocket-M
ath79: include rssileds package for ubnt devices with LEDs Some Ubiquiti devices had the RSSI LEDs configured in 01_leds but were missing the rssileds package, while others that don't have RSSI LEDS had the package included. This commit includes the rssileds package only for those devices that need it. Tested on a NanoStation M XW. Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
2019-11-13 15:18:59 +00:00
DEVICE_PACKAGES += rssileds
ath79: sort device definitions in image/* This applies alphabetic sorting to devices in image/* files. For certain cases, this patch deviates from strict sorting, e.g. to ensure that v10 comes after v9. While at it, fix an indent and remove some useless empty lines. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-08-22 12:34:45 +00:00
SUPPORTED_DEVICES += rocket-m
endef
TARGET_DEVICES += ubnt_rocket-m
define Device/ubnt_routerstation_common
ath79: harmonize line breaks in image Makefiles This harmonizes the line wrapping in image Makefile device definitions, as those are frequently copy-pasted and are a common subject of review comments. Having the treatment unifying should reduce the cases where adjustment is necessary afterwards. Harmonization is achieved by consistently (read "strictly") applying certain rules: - Never put more than 80 characters into one line - Fill lines up (do not break after 40 chars because of ...) - Use one tab for indent after wrapping by "\" - Only break after pipe "|" for IMAGE variables Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-12-19 19:42:19 +00:00
DEVICE_PACKAGES := -kmod-ath9k -wpad-mini -uboot-envtools kmod-usb-ohci \
kmod-usb2 fconfig
ath79: sort device definitions in image/* This applies alphabetic sorting to devices in image/* files. For certain cases, this patch deviates from strict sorting, e.g. to ensure that v10 comes after v9. While at it, fix an indent and remove some useless empty lines. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-08-22 12:34:45 +00:00
DEVICE_VENDOR := Ubiquiti
ath79: rename ATH_SOC to SOC This replaces ATH_SOC by the newly introduced common SOC device variable. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-12-20 00:12:42 +00:00
SOC := ar7161
ath79: sort device definitions in image/* This applies alphabetic sorting to devices in image/* files. For certain cases, this patch deviates from strict sorting, e.g. to ensure that v10 comes after v9. While at it, fix an indent and remove some useless empty lines. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-08-22 12:34:45 +00:00
IMAGE_SIZE := 16128k
IMAGES := factory.bin
ath79: harmonize line breaks in image Makefiles This harmonizes the line wrapping in image Makefile device definitions, as those are frequently copy-pasted and are a common subject of review comments. Having the treatment unifying should reduce the cases where adjustment is necessary afterwards. Harmonization is achieved by consistently (read "strictly") applying certain rules: - Never put more than 80 characters into one line - Fill lines up (do not break after 40 chars because of ...) - Use one tab for indent after wrapping by "\" - Only break after pipe "|" for IMAGE variables Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-12-19 19:42:19 +00:00
IMAGE/factory.bin := append-rootfs | pad-rootfs | mkubntimage | \
check-size $$$$(IMAGE_SIZE)
ath79: sort device definitions in image/* This applies alphabetic sorting to devices in image/* files. For certain cases, this patch deviates from strict sorting, e.g. to ensure that v10 comes after v9. While at it, fix an indent and remove some useless empty lines. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-08-22 12:34:45 +00:00
KERNEL := kernel-bin | append-dtb | lzma | pad-to $$(BLOCKSIZE)
KERNEL_INITRAMFS := kernel-bin | append-dtb
endef
define Device/ubnt_routerstation
$(Device/ubnt_routerstation_common)
DEVICE_MODEL := RouterStation
UBNT_BOARD := RS
UBNT_TYPE := RSx
UBNT_CHIP := ar7100
DEVICE_PACKAGES += -swconfig
SUPPORTED_DEVICES += routerstation
endef
TARGET_DEVICES += ubnt_routerstation
define Device/ubnt_routerstation-pro
$(Device/ubnt_routerstation_common)
DEVICE_MODEL := RouterStation Pro
UBNT_BOARD := RSPRO
UBNT_TYPE := RSPRO
UBNT_CHIP := ar7100pro
SUPPORTED_DEVICES += routerstation-pro
endef
TARGET_DEVICES += ubnt_routerstation-pro
ath79: fix dts files Add the SoC compatible to the individual dts files. Rename the dts files to match the common pattern. Remove dts files wich aren't used and no image in ar71xx exists. Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-05-08 05:22:38 +00:00
define Device/ubnt_unifi
ath79: add new OF only target for QCA MIPS silicon This target aims to replace ar71xx mid-term. The big part that is still missing is making the MMIO/AHB wifi work using OF. NAND and mikrotik subtargets will follow. Signed-off-by: John Crispin <john@phrozen.org>
2018-05-06 08:20:11 +00:00
$(Device/ubnt-bz)
ath79: split DEVICE_TITLE in multiple variables This allows the definition of DEVICE_VENDOR, DEVICE_MODEL and DEVICE_VARIANT. All three are merged together to look the same as the current DEVICE_TITLE. Also, if DEVICE_TITLE is set it's directly used as a *fallback* for devices which weren't upgraded yet. This is based on the work of @sudhanshu16. The motivation is to create JSON files based on provided metadata, needing clear differentiation between vendor, model and revision. Signed-off-by: Paul Spooren <mail@aparcar.org>
2019-06-16 19:34:46 +00:00
DEVICE_MODEL := UniFi
ath79: add and enforce image metadata Add metadata to images and make the metdata mandatory. Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-05-07 20:41:04 +00:00
SUPPORTED_DEVICES += unifi
ath79: add new OF only target for QCA MIPS silicon This target aims to replace ar71xx mid-term. The big part that is still missing is making the MMIO/AHB wifi work using OF. NAND and mikrotik subtargets will follow. Signed-off-by: John Crispin <john@phrozen.org>
2018-05-06 08:20:11 +00:00
endef
ath79: fix dts files Add the SoC compatible to the individual dts files. Rename the dts files to match the common pattern. Remove dts files wich aren't used and no image in ar71xx exists. Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-05-08 05:22:38 +00:00
TARGET_DEVICES += ubnt_unifi
ath79: add ubiquiti unifi ap ac lite/lr Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
2018-06-05 12:38:02 +00:00
ath79: sync naming of Ubiquiti devices Use a Unifi AC Lite board-/image name consistent with other Ubiquiti devices. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2018-06-27 10:10:33 +00:00
define Device/ubnt_unifiac
ath79: split DEVICE_TITLE in multiple variables This allows the definition of DEVICE_VENDOR, DEVICE_MODEL and DEVICE_VARIANT. All three are merged together to look the same as the current DEVICE_TITLE. Also, if DEVICE_TITLE is set it's directly used as a *fallback* for devices which weren't upgraded yet. This is based on the work of @sudhanshu16. The motivation is to create JSON files based on provided metadata, needing clear differentiation between vendor, model and revision. Signed-off-by: Paul Spooren <mail@aparcar.org>
2019-06-16 19:34:46 +00:00
DEVICE_VENDOR := Ubiquiti
ath79: rename ATH_SOC to SOC This replaces ATH_SOC by the newly introduced common SOC device variable. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-12-20 00:12:42 +00:00
SOC := qca9563
ath79: add ubiquiti unifi ap ac lite/lr Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
2018-06-05 12:38:02 +00:00
IMAGE_SIZE := 7744k
mac80211: make ath10k-ct the default ath10k We select ath10k-ct by default, but it is still possible to build the upstream version. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: John Crispin <john@phrozen.org>
2018-09-05 12:51:44 +00:00
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca988x-ct
ath79: add ubiquiti unifi ap ac lite/lr Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
2018-06-05 12:38:02 +00:00
endef
ath79: sync naming of Ubiquiti devices Use a Unifi AC Lite board-/image name consistent with other Ubiquiti devices. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2018-06-27 10:10:33 +00:00
define Device/ubnt_unifiac-lite
$(Device/ubnt_unifiac)
ath79: split DEVICE_TITLE in multiple variables This allows the definition of DEVICE_VENDOR, DEVICE_MODEL and DEVICE_VARIANT. All three are merged together to look the same as the current DEVICE_TITLE. Also, if DEVICE_TITLE is set it's directly used as a *fallback* for devices which weren't upgraded yet. This is based on the work of @sudhanshu16. The motivation is to create JSON files based on provided metadata, needing clear differentiation between vendor, model and revision. Signed-off-by: Paul Spooren <mail@aparcar.org>
2019-06-16 19:34:46 +00:00
DEVICE_MODEL := UniFi AC-Lite
ath79: correct ar71xx boardname for UniFi AC Lite This corrects the additional boardname for the image metadata to the one used in ar71xx. The previously present additional entry was never used on a running system. Reviewed-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Signed-off-by: David Bauer <mail@david-bauer.net>
2019-10-14 09:16:54 +00:00
SUPPORTED_DEVICES += unifiac-lite
ath79: add ubiquiti unifi ap ac lite/lr Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
2018-06-05 12:38:02 +00:00
endef
ath79: sync naming of Ubiquiti devices Use a Unifi AC Lite board-/image name consistent with other Ubiquiti devices. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2018-06-27 10:10:33 +00:00
TARGET_DEVICES += ubnt_unifiac-lite
ath79: add support for Ubiquiti UniFi AC-Pro rework the dts to a common unifi-ac dtsi pro network is connected via phy0 and has usb ports lite network is connected via phy4 without usb ports Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
2018-06-26 07:30:46 +00:00
ath79: add support for UniFi AC-LR The Unifi AC-LR has identical hardware to the Unifi AC-Lite. The antenna setup is different according to the vendor, which explains the thicker enclosure. Therefore, it is helpful to know the exact device variant, instead of having "Ubiquiti UniFi-AC-LITE/LR". Signed-off-by: Andreas Ziegler <dev@andreas-ziegler.de> [fix legacy name in commit message; add old boardname to SUPPORTED_DEVICES] Signed-off-by: David Bauer <mail@david-bauer.net>
2019-10-06 17:48:34 +00:00
define Device/ubnt_unifiac-lr
$(Device/ubnt_unifiac)
DEVICE_MODEL := UniFi AC-LR
SUPPORTED_DEVICES += unifiac-lite ubnt,unifiac-lite
endef
TARGET_DEVICES += ubnt_unifiac-lr
ath79: add support for Unifi AC Mesh The Unifi AC Mesh is equivalent to the Unifi AC Lite. However, for setting certain parameters with the flashed device it is helpful that the devices know their variant (e.g. automatically setting antenna gain for the different antennas in Lite and Mesh). Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2018-06-27 12:33:40 +00:00
define Device/ubnt_unifiac-mesh
$(Device/ubnt_unifiac)
ath79: split DEVICE_TITLE in multiple variables This allows the definition of DEVICE_VENDOR, DEVICE_MODEL and DEVICE_VARIANT. All three are merged together to look the same as the current DEVICE_TITLE. Also, if DEVICE_TITLE is set it's directly used as a *fallback* for devices which weren't upgraded yet. This is based on the work of @sudhanshu16. The motivation is to create JSON files based on provided metadata, needing clear differentiation between vendor, model and revision. Signed-off-by: Paul Spooren <mail@aparcar.org>
2019-06-16 19:34:46 +00:00
DEVICE_MODEL := UniFi AC-Mesh
ath79: fix SUPPORTED_DEVICES not matching ar71xx board names Based on a script for comparison, this fixes (hopefully) all errors in SUPPORTED_DEVICES for ar71xx->ath79 upgrade. Devices where old string is removed as the device does not exist in ar71xx: - dlink_dir-859-a1 - tplink_archer-a7-v5 - tplink_cpe510-v3 Devices where string is changed because it did not match the board name in ar71xx: - tplink_tl-mr3220-v1 - tplink_tl-mr3420-v1 - tplink_tl-wr2543-v1 - tplink_tl-wr741nd-v4 - tplink_tl-wr841-v7 - ubnt_unifiac-mesh - ubnt_unifiac-mesh-pro - ubnt_unifiac-pro For this device, the correct string could not be found, but we could not determine the correct one. Thus, the string is removed for now: - tplink_tl-wr740n-v4 The script for checking this is quite simple (note that newer entries, i.e. ath79->ath79 upgrade, are displayed as missing): newpath=target/linux/ath79/image/ oldpath=target/linux/ar71xx/base-files/lib/ar71xx.sh for s in $(grep -roh "SUPPORTED_DEVICES.*" $newpath | sed 's/SUPPORTED_DEVICES *.= *//'); do found="Missing" grep -q -r "\"$s\"" $oldpath && found="Found" echo "$s: $found." done The errors might be filtered by appending 'grep "Missing"' to the script. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-01-23 14:42:48 +00:00
SUPPORTED_DEVICES += unifiac-lite
ath79: add support for Unifi AC Mesh The Unifi AC Mesh is equivalent to the Unifi AC Lite. However, for setting certain parameters with the flashed device it is helpful that the devices know their variant (e.g. automatically setting antenna gain for the different antennas in Lite and Mesh). Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2018-06-27 12:33:40 +00:00
endef
TARGET_DEVICES += ubnt_unifiac-mesh
ath79: add support for UniFi AC-Mesh Pro The Unifi AC-Mesh Pro has identical hardware to the Unifi AC-Pro except USB support. Furthermore for setting parameters like antenna gain it is helpful to know the exact device variant. Signed-off-by: Christoph Krapp <achterin@googlemail.com>
2018-07-02 12:39:54 +00:00
define Device/ubnt_unifiac-mesh-pro
$(Device/ubnt_unifiac)
ath79: split DEVICE_TITLE in multiple variables This allows the definition of DEVICE_VENDOR, DEVICE_MODEL and DEVICE_VARIANT. All three are merged together to look the same as the current DEVICE_TITLE. Also, if DEVICE_TITLE is set it's directly used as a *fallback* for devices which weren't upgraded yet. This is based on the work of @sudhanshu16. The motivation is to create JSON files based on provided metadata, needing clear differentiation between vendor, model and revision. Signed-off-by: Paul Spooren <mail@aparcar.org>
2019-06-16 19:34:46 +00:00
DEVICE_MODEL := UniFi AC-Mesh Pro
ath79: fix SUPPORTED_DEVICES not matching ar71xx board names Based on a script for comparison, this fixes (hopefully) all errors in SUPPORTED_DEVICES for ar71xx->ath79 upgrade. Devices where old string is removed as the device does not exist in ar71xx: - dlink_dir-859-a1 - tplink_archer-a7-v5 - tplink_cpe510-v3 Devices where string is changed because it did not match the board name in ar71xx: - tplink_tl-mr3220-v1 - tplink_tl-mr3420-v1 - tplink_tl-wr2543-v1 - tplink_tl-wr741nd-v4 - tplink_tl-wr841-v7 - ubnt_unifiac-mesh - ubnt_unifiac-mesh-pro - ubnt_unifiac-pro For this device, the correct string could not be found, but we could not determine the correct one. Thus, the string is removed for now: - tplink_tl-wr740n-v4 The script for checking this is quite simple (note that newer entries, i.e. ath79->ath79 upgrade, are displayed as missing): newpath=target/linux/ath79/image/ oldpath=target/linux/ar71xx/base-files/lib/ar71xx.sh for s in $(grep -roh "SUPPORTED_DEVICES.*" $newpath | sed 's/SUPPORTED_DEVICES *.= *//'); do found="Missing" grep -q -r "\"$s\"" $oldpath && found="Found" echo "$s: $found." done The errors might be filtered by appending 'grep "Missing"' to the script. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-01-23 14:42:48 +00:00
SUPPORTED_DEVICES += unifiac-pro
ath79: add support for UniFi AC-Mesh Pro The Unifi AC-Mesh Pro has identical hardware to the Unifi AC-Pro except USB support. Furthermore for setting parameters like antenna gain it is helpful to know the exact device variant. Signed-off-by: Christoph Krapp <achterin@googlemail.com>
2018-07-02 12:39:54 +00:00
endef
TARGET_DEVICES += ubnt_unifiac-mesh-pro
ath79: add support for Ubiquiti UniFi AC-Pro rework the dts to a common unifi-ac dtsi pro network is connected via phy0 and has usb ports lite network is connected via phy4 without usb ports Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
2018-06-26 07:30:46 +00:00
define Device/ubnt_unifiac-pro
$(Device/ubnt_unifiac)
ath79: split DEVICE_TITLE in multiple variables This allows the definition of DEVICE_VENDOR, DEVICE_MODEL and DEVICE_VARIANT. All three are merged together to look the same as the current DEVICE_TITLE. Also, if DEVICE_TITLE is set it's directly used as a *fallback* for devices which weren't upgraded yet. This is based on the work of @sudhanshu16. The motivation is to create JSON files based on provided metadata, needing clear differentiation between vendor, model and revision. Signed-off-by: Paul Spooren <mail@aparcar.org>
2019-06-16 19:34:46 +00:00
DEVICE_MODEL := UniFi AC-Pro
treewide: remove kmod-usb-core from DEVICE_PACKAGES This removes _all_ occurrences of kmod-usb-core from DEVICE_PACKAGES and similar variables. This package is pulled as dependency by one of the following packages in any case: - kmod-usb-chipidea - kmod-usb-dwc2 - kmod-usb-ledtrig-usbport - kmod-usb-ohci - kmod-usb2 - kmod-usb2-pci - kmod-usb3 Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> [remove kmod-usb-core from EnGenius ESR600] Signed-off-by: David Bauer <mail@david-bauer.net>
2019-09-22 10:06:25 +00:00
DEVICE_PACKAGES += kmod-usb2
ath79: fix SUPPORTED_DEVICES not matching ar71xx board names Based on a script for comparison, this fixes (hopefully) all errors in SUPPORTED_DEVICES for ar71xx->ath79 upgrade. Devices where old string is removed as the device does not exist in ar71xx: - dlink_dir-859-a1 - tplink_archer-a7-v5 - tplink_cpe510-v3 Devices where string is changed because it did not match the board name in ar71xx: - tplink_tl-mr3220-v1 - tplink_tl-mr3420-v1 - tplink_tl-wr2543-v1 - tplink_tl-wr741nd-v4 - tplink_tl-wr841-v7 - ubnt_unifiac-mesh - ubnt_unifiac-mesh-pro - ubnt_unifiac-pro For this device, the correct string could not be found, but we could not determine the correct one. Thus, the string is removed for now: - tplink_tl-wr740n-v4 The script for checking this is quite simple (note that newer entries, i.e. ath79->ath79 upgrade, are displayed as missing): newpath=target/linux/ath79/image/ oldpath=target/linux/ar71xx/base-files/lib/ar71xx.sh for s in $(grep -roh "SUPPORTED_DEVICES.*" $newpath | sed 's/SUPPORTED_DEVICES *.= *//'); do found="Missing" grep -q -r "\"$s\"" $oldpath && found="Found" echo "$s: $found." done The errors might be filtered by appending 'grep "Missing"' to the script. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-01-23 14:42:48 +00:00
SUPPORTED_DEVICES += unifiac-pro
ath79: add support for Ubiquiti UniFi AC-Pro rework the dts to a common unifi-ac dtsi pro network is connected via phy0 and has usb ports lite network is connected via phy4 without usb ports Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
2018-06-26 07:30:46 +00:00
endef
TARGET_DEVICES += ubnt_unifiac-pro
Reference in New Issue Copy Permalink