ExternalVendorCode/openwrt
1
0
Fork 0
mirror of https://github.com/openwrt/openwrt.git synced 2024-12-28 17:48:58 +00:00
Code Issues Actions 7 Packages Projects Releases Wiki Activity
a25809a474
openwrt/target/linux/realtek/image/rtl839x.mk

83 lines
1.9 KiB
Makefile
Raw Normal View History

realtek: Add support for ZyXEL GS1900-48 Switch The GS1900-48 is a 48 + 2 port Gigabit L2 switch with 48 gigabit ports. Hardware: RTL8393M SoC Macronix MX25l12805D (16MB flash) 128MB RAM 6 * RTL8218B external PHY 2 * RTL8231 GPIO extenders to control the port LEDs, system LED and Reset button 2 Uplink ports are SFP cages which support 1000 Base-X mini GBIC modules. Power is supplied via a 230 volt mains connector. The board has a hard reset switch SW1, which is is not reachable from the outside. J4 provides a 12V RS232 serial connector which is connected through U8 to the 3.3V UART of the RTL8393. Conversion is done by U8, a SIPEX 3232EC. To connect to the UART, wires can be soldered to R603 (TX) and R602 (RX). Installation: Install the squashfs image via Realtek's original Web-Interface. Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2021-12-31 11:51:45 +00:00
# SPDX-License-Identifier: GPL-2.0-only
realtek: merge duplicated DGS-1210 recipes The D-Link DGS-1210 device series currently has supported devices with both RTL838x and RTL839x SoCs. An image build recipe has been defined in both subtarget makefiles, but these are mostly identical, save for the SOC variable. Move the SOC variable from the DGS-1210 build recipes to the applicable devices, and put the remaining duplicate code in a shared Makefile. Signed-off-by: Sander Vanheule <sander@svanheule.net>
2022-09-17 20:06:37 +00:00
include ./common.mk
realtek: add support for DGS-1210-52 Hardware specification ---------------------- * RTL8393M SoC, 1 MIPS 34Kc core @ 700MHz * 128MB DRAM * 32MB NOR Flash * 48 x 10/100/1000BASE-T ports - 6 x External PHY with 8 ports (RTL8218D) * 4 x Gigabit RJ45/SFP Combo ports - External PHY with 4 SFP ports (RTL8214FC) * Power LED * Reset button on front panel * UART (115200 8N1) via unpopulated standard 0.1" pin header marked J14 The gpio-restart node is not required but it does reset the switch. TODO: The 4 combo ports attached to the RTL8214FC are not detect properly. Linux kernel reports 49 and 50 as "External RTL8393 SERDES" and 51 and 52 as "RTL8218B (external)". Those ports only work if u-boot initialize it (for example, loading initramfs image using one of those ports). A patch to PHY detection is needed for full support. The firmware recovery using U-Boot is broken for all DGS-1210 tested devices as pressing RESET does not trigger it (only if pressed from a running stock image) UART pinout ----------- [o]ooo|J14 | ||`------ GND | |`------- RX | `-------- TX `---------- Vcc (3V3) Installation using OEM upgrade ------------------------------ 1. Make sure you are running OEM firmware in image2 slot (logged as admin): - > config firmware image_id 2 boot_up - > reboot 2. Install squashfs-factory_image1.bin to image1 using (logged as admin): - > download firmware_fromTFTP <tftpserver> factory_image1.bin - > config firmware image_id 1 boot_up - > reboot Installation using serial interface ----------------------------------- 1. Press Escape key during `Hit Esc key to stop autoboot` prompt 2. Press CTRL+C keys to get into real U-Boot prompt 3. Init network with `rtk network on` command 4. Load image with `tftpboot 0x8f000000 openwrt-realtek-rtl839x-d-link_dgs-1210-52-initramfs-kernel.bin` command 5. Boot the image with `bootm` command Once booted the initramfs, install the squashfs-sysupgrade.bin as a normal OpenWrt system. Dual-boot with stock firmware using writable u-boot-env ------------------------------------------------------- From stock to OpenWrt / boot image 1 (CLI as admin): - > config firmware image_id 1 boot_up - > reboot From OpenWrt to stock / boot image 2: (shell as root) - # fw_setenv bootcmd 'run addargs ; bootm 0xb4e80000' - # fw_setenv image '/dev/mtdblock7' - # reboot Debrick using serial interface ------------------------------ 1. Press Escape key during `Hit Esc key to stop autoboot` prompt 2. In a Windows PC, run 'D-Link Network Assistant v2.0.2.4'. It should detect the switch 3. Flash the firmware. Back to stock firmware using dual-boot -------------------------------------- If you have serial interface, you can change u-boot env vars interrupting the boot process. If not but you are running OpenWrt, you can dual-boot (as mentioned eariler) and skip to step 4: 1. Press Escape key during `Hit Esc key to stop autoboot` prompt 2. Press CTRL+C keys to get into real U-Boot prompt 3. Boot the image 2: - set image /dev/mtdblock7; run addargs; bootm 0xb4e80000 4. Once booted, log as admin and change the boot image to 2 - > config firmware image_id 2 boot_up - > reboot 5. After the boot, flash image1 with the vendor image Back to stock firmware using DNA -------------------------------- 1. From an OpenWrt: - # fw_setenv bootstop on - # reboot 2. In a Windows PC, run 'D-Link Network Assistant v2.0.2.4'. It should detect the switch 3. Flash the firmware. It has been developed and tested on device with F3 revision. Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de> Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
2022-09-17 17:12:19 +00:00
define Device/d-link_dgs-1210-52
realtek: use Device prefix for common recipes The Build prefix is used for image build commands, while the Device prefix should be used for base recipes for devices. Apply the same naming convention here. While touching the file, also fix the mixed indentation. Suggested-by: INAGAKI Hiroshi <musashino.open@gmail.com> Signed-off-by: Sander Vanheule <sander@svanheule.net>
2022-09-18 08:12:16 +00:00
$(Device/d-link_dgs-1210)
realtek: merge duplicated DGS-1210 recipes The D-Link DGS-1210 device series currently has supported devices with both RTL838x and RTL839x SoCs. An image build recipe has been defined in both subtarget makefiles, but these are mostly identical, save for the SOC variable. Move the SOC variable from the DGS-1210 build recipes to the applicable devices, and put the remaining duplicate code in a shared Makefile. Signed-off-by: Sander Vanheule <sander@svanheule.net>
2022-09-17 20:06:37 +00:00
SOC := rtl8393
realtek: add support for DGS-1210-52 Hardware specification ---------------------- * RTL8393M SoC, 1 MIPS 34Kc core @ 700MHz * 128MB DRAM * 32MB NOR Flash * 48 x 10/100/1000BASE-T ports - 6 x External PHY with 8 ports (RTL8218D) * 4 x Gigabit RJ45/SFP Combo ports - External PHY with 4 SFP ports (RTL8214FC) * Power LED * Reset button on front panel * UART (115200 8N1) via unpopulated standard 0.1" pin header marked J14 The gpio-restart node is not required but it does reset the switch. TODO: The 4 combo ports attached to the RTL8214FC are not detect properly. Linux kernel reports 49 and 50 as "External RTL8393 SERDES" and 51 and 52 as "RTL8218B (external)". Those ports only work if u-boot initialize it (for example, loading initramfs image using one of those ports). A patch to PHY detection is needed for full support. The firmware recovery using U-Boot is broken for all DGS-1210 tested devices as pressing RESET does not trigger it (only if pressed from a running stock image) UART pinout ----------- [o]ooo|J14 | ||`------ GND | |`------- RX | `-------- TX `---------- Vcc (3V3) Installation using OEM upgrade ------------------------------ 1. Make sure you are running OEM firmware in image2 slot (logged as admin): - > config firmware image_id 2 boot_up - > reboot 2. Install squashfs-factory_image1.bin to image1 using (logged as admin): - > download firmware_fromTFTP <tftpserver> factory_image1.bin - > config firmware image_id 1 boot_up - > reboot Installation using serial interface ----------------------------------- 1. Press Escape key during `Hit Esc key to stop autoboot` prompt 2. Press CTRL+C keys to get into real U-Boot prompt 3. Init network with `rtk network on` command 4. Load image with `tftpboot 0x8f000000 openwrt-realtek-rtl839x-d-link_dgs-1210-52-initramfs-kernel.bin` command 5. Boot the image with `bootm` command Once booted the initramfs, install the squashfs-sysupgrade.bin as a normal OpenWrt system. Dual-boot with stock firmware using writable u-boot-env ------------------------------------------------------- From stock to OpenWrt / boot image 1 (CLI as admin): - > config firmware image_id 1 boot_up - > reboot From OpenWrt to stock / boot image 2: (shell as root) - # fw_setenv bootcmd 'run addargs ; bootm 0xb4e80000' - # fw_setenv image '/dev/mtdblock7' - # reboot Debrick using serial interface ------------------------------ 1. Press Escape key during `Hit Esc key to stop autoboot` prompt 2. In a Windows PC, run 'D-Link Network Assistant v2.0.2.4'. It should detect the switch 3. Flash the firmware. Back to stock firmware using dual-boot -------------------------------------- If you have serial interface, you can change u-boot env vars interrupting the boot process. If not but you are running OpenWrt, you can dual-boot (as mentioned eariler) and skip to step 4: 1. Press Escape key during `Hit Esc key to stop autoboot` prompt 2. Press CTRL+C keys to get into real U-Boot prompt 3. Boot the image 2: - set image /dev/mtdblock7; run addargs; bootm 0xb4e80000 4. Once booted, log as admin and change the boot image to 2 - > config firmware image_id 2 boot_up - > reboot 5. After the boot, flash image1 with the vendor image Back to stock firmware using DNA -------------------------------- 1. From an OpenWrt: - # fw_setenv bootstop on - # reboot 2. In a Windows PC, run 'D-Link Network Assistant v2.0.2.4'. It should detect the switch 3. Flash the firmware. It has been developed and tested on device with F3 revision. Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de> Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
2022-09-17 17:12:19 +00:00
DEVICE_MODEL := DGS-1210-52
endef
TARGET_DEVICES += d-link_dgs-1210-52
realtek: add support for HPE 1920-48G (JG927A) and 1920-48G-PoE (JG928A) Hardware information: --------------------- - SoC: RTL8393M - Copper phy: 6×RTL8218B - Fibre phy: RTL8214FC - Flash: 32MiB SPI NOR, MX25L25635FMI - RAM: 128MiB DDR3, Micron MT41K64M16TW-107 - Serial port: ±5V serial port to RJ45, ZT3232 (MAX3232 compatible) - +370W POE on JG928A model Note: SFP ports currently non-functional due to missing support for RTL8214FC on the RTL8393M target. Updated for Linux 6.6 kernel. Installation: ------------- - Initial installation follows same process as HPE 1920-24G (JG924A) - Based on prior work of Jan Hoffmann <jan@3e8.eu> - Additional work by Andreas Böhler <dev@aboehler.at> - PoE updates and tidy-up by Stephen Howell <howels@allthatwemight.be> Signed-off-by: Stephen Howell <howels@allthatwemight.be>
2023-04-25 15:32:07 +00:00
define Device/hpe_1920-48g
$(Device/hpe_1920)
SOC := rtl8393
DEVICE_MODEL := 1920-48G (JG927A)
H3C_DEVICE_ID := 0x0001002a
endef
TARGET_DEVICES += hpe_1920-48g
define Device/hpe_1920-48g-poe
$(Device/hpe_1920)
SOC := rtl8393
DEVICE_MODEL := 1920-48G-PoE (JG928A)
DEVICE_PACKAGES += realtek-poe
H3C_DEVICE_ID := 0x0001002b
endef
TARGET_DEVICES += hpe_1920-48g-poe
realtek: add support for Netgear GS750E This is an RTL8393-based switch with 48 RJ-45 and 2 SFP ports. Hardware -------- SoC: Realtek RTL8393M RAM: 128MB DDR3 (Nanya NT5CC64M16GP-DI) FLASH: 8MB NOR (Macronix MX25L6433F) ETH: 48x 10/100/1000 Mbps RJ-45 Ethernet SFP: 2x SFP BTN: - 1x Reset button LEDS: - 50x Green-Amber leds: lan/sfp status - 1x Green led: power (Always on) UART: - 115200-8-N-1 (CN3, pin-out on PCB) Everything works correctly except for the 2 SFP ports that are not working unless you enable it every boot in U-Boot with the command: rtk network on Installation ------------ You can install Openwrt using one of the following methods. Warning: flashing OpenWrt will delete your current configuration. Warning 2: if the -factory.bix file is not available anymore, you must follow Method 2. Method 1: Check the firmware version currently running on your switch. If you are running FW V1.0.1.10 or greater, you have to download the firmware V1.0.1.8 from Netgear website and then flash this version. When the switch restarts, it should be on version V1.0.1.8. Now you can get the OpenWrt -factory.bix file and then flash it using the OEM web interface. Method 2 (requires the UART connection): Boot the -initramfs-kernel.bin image from U-Boot with these commands: rtk network on; tftpboot 0x8f000000 openwrt-realtek-rtl839x-netgear_gs750e-initramfs-kernel.bin; bootm; And then flash the -sysupgrade.bin file from OpenWrt. Revert to stock --------------- Get the stock firmware from the Netgear website and flash it using the OpenWrt web interface. Remember to not keep the current configuration and check the "Force upgrade" checkbox Once reverted to stock the firmware could complain in the UART console about mtdblock3 and/or mtdblock4 not being mounted correctly but it seems to work anyway without any problems. Sample error: mount: Mounting /dev/mtdblock4 on /mntlog failed: Input/output error If you want to get rid of these error messages you can boot the -initramfs-kernel.bin image from U-Boot with these commands: rtk network on; tftpboot 0x8f000000 openwrt-realtek-rtl839x-netgear_gs750e-initramfs-kernel.bin; bootm; And then erase the corresponding partitions using the command: For mtdblock3: mtd erase jffs2_cfg For mtdblock4: mtd erase jffs2_log Now you can reboot the switch and the errors should be gone Note ---- To get the SFP ports fully working, all the right GPIOs must be found. In the GPL sources I found these: - GPIO_14: SFP_TX_DIS1; - GPIO_19: SFP_TX_DIS0; Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
2023-01-03 13:27:50 +00:00
# When the factory image won't fit anymore, it can be removed.
# New installation will be performed booting the initramfs image from
# ram and then flashing the sysupgrade image from OpenWrt
define Device/netgear_gs750e
SOC := rtl8393
IMAGE_SIZE := 7552k
FACTORY_SIZE := 6528k
DEVICE_VENDOR := NETGEAR
DEVICE_MODEL := GS750E
UIMAGE_MAGIC := 0x174e4741
IMAGES += factory.bix
IMAGE/factory.bix := \
append-kernel | \
pad-to 64k | \
append-rootfs | \
pad-rootfs | \
check-size $$$$(FACTORY_SIZE)
endef
TARGET_DEVICES += netgear_gs750e
realtek: add support for Panasonic Switch-M48eG PN28480K Panasonic Switch-M48eG PN28480K is a 48 + 4 port gigabit switch, based on RTL8393M. Specification: - SoC : Realtek RTL8393M - RAM : DDR3 128 MiB (Winbond W631GG8KB-15) - Flash : SPI-NOR 32 MiB (Macronix MX25L25635FMI-10G) - Ethernet : 10/100/1000 Mbps x48 + 2 - port 1-40 : TP, RTL8218B x5 - port 41-48 : RTL8218FB - port 41-44: TP - port 45-48: TP/SFP (Combo) - LEDs/Keys : 7x / 1x - UART : RS-232 port on the front panel (connector: RJ-45) - 3:TX, 4:GND, 5:GND, 6:RX (pin number: RJ-45) - 9600n8 - Power : 100-240 VAC, 50/60 Hz, 0.5 A - Plug : IEC 60320-C13 - Stock OS : VxWorks based Flash instruction using initramfs image: 1. Prepare the TFTP server with the IP address 192.168.1.111 2. Rename the OpenWrt initramfs image to "0101A8C0.img" and place it to the TFTP directory 3. Download the official upgrading firmware (ex: pn28480k_v30000.rom) and place it to the TFTP directory 4. Boot M48eG and interrupt the U-Boot with Ctrl + C keys 5. Execute the following commands and boot with the OpenWrt initramfs image rtk network on tftpboot 0x81000000 bootm 6. Backup mtdblock files to the computer by scp or anything and reboot 7. Interrupt the U-Boot and execute the following commands to re-create filesystem in the flash ffsmount c:/ ffsfmt c:/ this step takes a long time, about ~ 4 mins 8. Execute the following commands to put the official images to the filesystem updatert <official image> example: updatert pn28480k_v30000.rom this step takes about ~ 40 secs 9. Set the environment variables of the U-Boot by the following commands setenv loadaddr 0xb4e00000 setenv bootcmd 'sleep 10; bootm;' saveenv 'sleep 10;' is required as dummy to execute 'bootm' command correctly 10: Download the OpenWrt initramfs image and boot with it tftpboot 0x81000000 0101A8C0.img bootm 11: On the initramfs image, download the sysupgrade image and perform sysupgrade with it sysupgrade <imagename> 12: Wait ~ 120 seconds to complete flashing Known Issues: - 4x SFP ports are provided as combo ports by the RTL8218FB chip, but the phy driver has no support for it. Currently, only TP ports work by the RTL8218B support. Note: - "Switch-M48eG" is a model name, and "PN28480K" is a model number. Switch-M48eG has an another (old) model number ("PN28480"), it's not a Realtek based hardware. - Switch-M48eG has a "POWER" LED (Green), but it's not connected to any GPIO pin. - U-Boot checks the runtime images in the flash when booting and fails to execute "bootcmd" variable if the images are not existing. - A filesystem is formed in the flash (0x100000-0x1DFFFFF) on the stock firmware and it includes the stock images, configuration files and checksum files. It's unknown format, can't be managed on the OpenWrt. To get the enough space for OpenWrt, move the filesystem to the head of "fs_reserved" partition by execution of "ffsfmt" and "updatert". - A GPIO pin on PCA9539 is used for resetting external RTL8218B phys and RTL8218FB phy. This should be specified as "reset-gpios" property in MDIO node, but the current configuration of RTL8218B phy in the driver seems to be incomplete and RTL8218FB won't be configured on RTL8218D support. So, ethernet ports on these phys will be broken after hard-resetting. At the moment, configure this pin as gpio-hog to avoid breaking by resetting. - This model has 2x Microchip TCN75A thermal sensors. Linux Kernel supports TCN75 chip on lm75 driver, but no support for TCN75'A' variant. At the moment, use TCN75 support for the chips instead. Back to the stock firmware: 1. Delete "loadaddr" variable and set "bootcmd" to the original value on U-Boot: setenv loadaddr setenv bootcmd 'ffsrdm c:/runtime.had 0x81000000;alphadec c:/runtime.had 0x81000240 0x80010000;' on OpenWrt: fw_setenv loadaddr fw_setenv bootcmd 'ffsrdm c:/runtime.had 0x81000000;alphadec c:/runtime.had 0x81000240 0x80010000;' 2. Perform reset or reboot on U-Boot: reset on OpenWrt: reboot Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2021-09-03 09:58:09 +00:00
define Device/panasonic_m48eg-pn28480k
SOC := rtl8393
IMAGE_SIZE := 16384k
DEVICE_VENDOR := Panasonic
DEVICE_MODEL := Switch-M48eG
DEVICE_VARIANT := PN28480K
realtek: Cleanup Makefiles Our current Makefiles a little bit messy and can be improved somewhat, both in whitespace and in style. Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
2022-12-21 22:26:08 +00:00
DEVICE_PACKAGES := \
kmod-hwmon-gpiofan \
kmod-hwmon-lm75 \
kmod-i2c-mux-pca954x \
realtek: add support for Panasonic Switch-M48eG PN28480K Panasonic Switch-M48eG PN28480K is a 48 + 4 port gigabit switch, based on RTL8393M. Specification: - SoC : Realtek RTL8393M - RAM : DDR3 128 MiB (Winbond W631GG8KB-15) - Flash : SPI-NOR 32 MiB (Macronix MX25L25635FMI-10G) - Ethernet : 10/100/1000 Mbps x48 + 2 - port 1-40 : TP, RTL8218B x5 - port 41-48 : RTL8218FB - port 41-44: TP - port 45-48: TP/SFP (Combo) - LEDs/Keys : 7x / 1x - UART : RS-232 port on the front panel (connector: RJ-45) - 3:TX, 4:GND, 5:GND, 6:RX (pin number: RJ-45) - 9600n8 - Power : 100-240 VAC, 50/60 Hz, 0.5 A - Plug : IEC 60320-C13 - Stock OS : VxWorks based Flash instruction using initramfs image: 1. Prepare the TFTP server with the IP address 192.168.1.111 2. Rename the OpenWrt initramfs image to "0101A8C0.img" and place it to the TFTP directory 3. Download the official upgrading firmware (ex: pn28480k_v30000.rom) and place it to the TFTP directory 4. Boot M48eG and interrupt the U-Boot with Ctrl + C keys 5. Execute the following commands and boot with the OpenWrt initramfs image rtk network on tftpboot 0x81000000 bootm 6. Backup mtdblock files to the computer by scp or anything and reboot 7. Interrupt the U-Boot and execute the following commands to re-create filesystem in the flash ffsmount c:/ ffsfmt c:/ this step takes a long time, about ~ 4 mins 8. Execute the following commands to put the official images to the filesystem updatert <official image> example: updatert pn28480k_v30000.rom this step takes about ~ 40 secs 9. Set the environment variables of the U-Boot by the following commands setenv loadaddr 0xb4e00000 setenv bootcmd 'sleep 10; bootm;' saveenv 'sleep 10;' is required as dummy to execute 'bootm' command correctly 10: Download the OpenWrt initramfs image and boot with it tftpboot 0x81000000 0101A8C0.img bootm 11: On the initramfs image, download the sysupgrade image and perform sysupgrade with it sysupgrade <imagename> 12: Wait ~ 120 seconds to complete flashing Known Issues: - 4x SFP ports are provided as combo ports by the RTL8218FB chip, but the phy driver has no support for it. Currently, only TP ports work by the RTL8218B support. Note: - "Switch-M48eG" is a model name, and "PN28480K" is a model number. Switch-M48eG has an another (old) model number ("PN28480"), it's not a Realtek based hardware. - Switch-M48eG has a "POWER" LED (Green), but it's not connected to any GPIO pin. - U-Boot checks the runtime images in the flash when booting and fails to execute "bootcmd" variable if the images are not existing. - A filesystem is formed in the flash (0x100000-0x1DFFFFF) on the stock firmware and it includes the stock images, configuration files and checksum files. It's unknown format, can't be managed on the OpenWrt. To get the enough space for OpenWrt, move the filesystem to the head of "fs_reserved" partition by execution of "ffsfmt" and "updatert". - A GPIO pin on PCA9539 is used for resetting external RTL8218B phys and RTL8218FB phy. This should be specified as "reset-gpios" property in MDIO node, but the current configuration of RTL8218B phy in the driver seems to be incomplete and RTL8218FB won't be configured on RTL8218D support. So, ethernet ports on these phys will be broken after hard-resetting. At the moment, configure this pin as gpio-hog to avoid breaking by resetting. - This model has 2x Microchip TCN75A thermal sensors. Linux Kernel supports TCN75 chip on lm75 driver, but no support for TCN75'A' variant. At the moment, use TCN75 support for the chips instead. Back to the stock firmware: 1. Delete "loadaddr" variable and set "bootcmd" to the original value on U-Boot: setenv loadaddr setenv bootcmd 'ffsrdm c:/runtime.had 0x81000000;alphadec c:/runtime.had 0x81000240 0x80010000;' on OpenWrt: fw_setenv loadaddr fw_setenv bootcmd 'ffsrdm c:/runtime.had 0x81000000;alphadec c:/runtime.had 0x81000240 0x80010000;' 2. Perform reset or reboot on U-Boot: reset on OpenWrt: reboot Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2021-09-03 09:58:09 +00:00
kmod-thermal
endef
TARGET_DEVICES += panasonic_m48eg-pn28480k
realtek: add support for TP-Link SG2452P v4 aka T1600G-52PS v4 This is an RTL8393-based switch with 802.3af on all 48 ports. Specifications: --------------- * SoC: Realtek RTL8393M * Flash: 32 MiB SPI flash * RAM: 256 MiB * Ethernet: 48x 10/100/1000 Mbps with PoE+ * Buttons: 1x "Reset" button, 1x "Speed" button * UART: 1x serial header, unpopulated * PoE: 12x TI TPS23861 I2C PoE controller, 384W PoE budget * SFP: 4 SFP ports Works: ------ - (48) RJ-45 ethernet ports - Switch functions - Buttons - All LEDs on front panel except port LEDs - Fan monitoring and basic control Not yet enabled: ---------------- - PoE - ICs are not in AUTO mode, so the kernel driver is not usable - Port LEDs - SFP cages Install via web interface: ------------------------- Not supported at this time. Install via serial console/tftp: -------------------------------- The U-Boot firmware drops to a TP-Link specific "BOOTUTIL" shell at 38400 baud. There is no known way to exit out of this shell, and no way to do anything useful. Ideally, one would trick the bootloader into flashing the sysupgrade image first. However, if the image exceeds 6MiB in size, it will not work. To install OpenWRT: Prepare a tftp server with: 1. server address: 192.168.0.146 2. the image as: "uImage.img" Power on device, and stop boot by pressing any key. Once the shell is active: 1. Ground out the CLK (pin 16) of the ROM (U6) 2. Select option "3. Start" 3. Bootloader notes that "The kernel has been damaged!" 4. Release CLK as soon as bootloader thinks image is corrupted. 5. Bootloader enters automatic recovery -- details printed on console 6. Watch as the bootloader flashes and boots OpenWRT. Blind install via tftp: ----------------------- This method works when it's not feasible to install a serial header. Prepare a tftp server with: 1. server address: 192.168.0.146 2. the image as: "uImage.img" 3. Watch network traffic (tcpdump or wireshark works) 4. Power on the device. 5. Wait 1-2 seconds then ground out the CLK (pin 16) of the ROM (U6) 6. When 192.168.0.30 makes tftp requests, release pin 16 7. Wait 2-3 minutes for device to auto-flash and boot OpenWRT Signed-off-by: Andreas Böhler <dev@aboehler.at>
2022-08-26 09:21:40 +00:00
define Device/tplink_sg2452p-v4
SOC := rtl8393
KERNEL_SIZE := 6m
IMAGE_SIZE := 26m
DEVICE_VENDOR := TP-Link
DEVICE_MODEL := SG2452P
DEVICE_VARIANT := v4
realtek: Cleanup Makefiles Our current Makefiles a little bit messy and can be improved somewhat, both in whitespace and in style. Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
2022-12-21 22:26:08 +00:00
DEVICE_PACKAGES := \
kmod-hwmon-gpiofan \
kmod-hwmon-tps23861
realtek: add support for TP-Link SG2452P v4 aka T1600G-52PS v4 This is an RTL8393-based switch with 802.3af on all 48 ports. Specifications: --------------- * SoC: Realtek RTL8393M * Flash: 32 MiB SPI flash * RAM: 256 MiB * Ethernet: 48x 10/100/1000 Mbps with PoE+ * Buttons: 1x "Reset" button, 1x "Speed" button * UART: 1x serial header, unpopulated * PoE: 12x TI TPS23861 I2C PoE controller, 384W PoE budget * SFP: 4 SFP ports Works: ------ - (48) RJ-45 ethernet ports - Switch functions - Buttons - All LEDs on front panel except port LEDs - Fan monitoring and basic control Not yet enabled: ---------------- - PoE - ICs are not in AUTO mode, so the kernel driver is not usable - Port LEDs - SFP cages Install via web interface: ------------------------- Not supported at this time. Install via serial console/tftp: -------------------------------- The U-Boot firmware drops to a TP-Link specific "BOOTUTIL" shell at 38400 baud. There is no known way to exit out of this shell, and no way to do anything useful. Ideally, one would trick the bootloader into flashing the sysupgrade image first. However, if the image exceeds 6MiB in size, it will not work. To install OpenWRT: Prepare a tftp server with: 1. server address: 192.168.0.146 2. the image as: "uImage.img" Power on device, and stop boot by pressing any key. Once the shell is active: 1. Ground out the CLK (pin 16) of the ROM (U6) 2. Select option "3. Start" 3. Bootloader notes that "The kernel has been damaged!" 4. Release CLK as soon as bootloader thinks image is corrupted. 5. Bootloader enters automatic recovery -- details printed on console 6. Watch as the bootloader flashes and boots OpenWRT. Blind install via tftp: ----------------------- This method works when it's not feasible to install a serial header. Prepare a tftp server with: 1. server address: 192.168.0.146 2. the image as: "uImage.img" 3. Watch network traffic (tcpdump or wireshark works) 4. Power on the device. 5. Wait 1-2 seconds then ground out the CLK (pin 16) of the ROM (U6) 6. When 192.168.0.30 makes tftp requests, release pin 16 7. Wait 2-3 minutes for device to auto-flash and boot OpenWRT Signed-off-by: Andreas Böhler <dev@aboehler.at>
2022-08-26 09:21:40 +00:00
endef
TARGET_DEVICES += tplink_sg2452p-v4
realtek: Add support for ZyXEL GS1900-48 Switch The GS1900-48 is a 48 + 2 port Gigabit L2 switch with 48 gigabit ports. Hardware: RTL8393M SoC Macronix MX25l12805D (16MB flash) 128MB RAM 6 * RTL8218B external PHY 2 * RTL8231 GPIO extenders to control the port LEDs, system LED and Reset button 2 Uplink ports are SFP cages which support 1000 Base-X mini GBIC modules. Power is supplied via a 230 volt mains connector. The board has a hard reset switch SW1, which is is not reachable from the outside. J4 provides a 12V RS232 serial connector which is connected through U8 to the 3.3V UART of the RTL8393. Conversion is done by U8, a SIPEX 3232EC. To connect to the UART, wires can be soldered to R603 (TX) and R602 (RX). Installation: Install the squashfs image via Realtek's original Web-Interface. Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2021-12-31 11:51:45 +00:00
define Device/zyxel_gs1900-48
realtek: deduplicate GS1900 recipes ZyXEL GS1900 devices with SoCs from both the RTL838x and RTL839x families share the same image structure and size of the firmware partition. Additionally, the GS1900-48 recipe provided a parameter for the zyxel-vers command, but this parameter is not used. Deduplicate the recipes by moving it to target/linux/realtek/image/common.mk. Signed-off-by: Sander Vanheule <sander@svanheule.net>
2022-12-28 20:39:46 +00:00
$(Device/zyxel_gs1900)
realtek: Add support for ZyXEL GS1900-48 Switch The GS1900-48 is a 48 + 2 port Gigabit L2 switch with 48 gigabit ports. Hardware: RTL8393M SoC Macronix MX25l12805D (16MB flash) 128MB RAM 6 * RTL8218B external PHY 2 * RTL8231 GPIO extenders to control the port LEDs, system LED and Reset button 2 Uplink ports are SFP cages which support 1000 Base-X mini GBIC modules. Power is supplied via a 230 volt mains connector. The board has a hard reset switch SW1, which is is not reachable from the outside. J4 provides a 12V RS232 serial connector which is connected through U8 to the 3.3V UART of the RTL8393. Conversion is done by U8, a SIPEX 3232EC. To connect to the UART, wires can be soldered to R603 (TX) and R602 (RX). Installation: Install the squashfs image via Realtek's original Web-Interface. Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2021-12-31 11:51:45 +00:00
SOC := rtl8393
DEVICE_MODEL := GS1900-48
realtek: deduplicate GS1900 recipes ZyXEL GS1900 devices with SoCs from both the RTL838x and RTL839x families share the same image structure and size of the firmware partition. Additionally, the GS1900-48 recipe provided a parameter for the zyxel-vers command, but this parameter is not used. Deduplicate the recipes by moving it to target/linux/realtek/image/common.mk. Signed-off-by: Sander Vanheule <sander@svanheule.net>
2022-12-28 20:39:46 +00:00
ZYXEL_VERS := AAHN
realtek: Add support for ZyXEL GS1900-48 Switch The GS1900-48 is a 48 + 2 port Gigabit L2 switch with 48 gigabit ports. Hardware: RTL8393M SoC Macronix MX25l12805D (16MB flash) 128MB RAM 6 * RTL8218B external PHY 2 * RTL8231 GPIO extenders to control the port LEDs, system LED and Reset button 2 Uplink ports are SFP cages which support 1000 Base-X mini GBIC modules. Power is supplied via a 230 volt mains connector. The board has a hard reset switch SW1, which is is not reachable from the outside. J4 provides a 12V RS232 serial connector which is connected through U8 to the 3.3V UART of the RTL8393. Conversion is done by U8, a SIPEX 3232EC. To connect to the UART, wires can be soldered to R603 (TX) and R602 (RX). Installation: Install the squashfs image via Realtek's original Web-Interface. Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2021-12-31 11:51:45 +00:00
endef
TARGET_DEVICES += zyxel_gs1900-48
Reference in New Issue Copy Permalink