openwrt/target/linux/ath79/dts/qca9557_sophos_ap15c.dts

160 lines
2.7 KiB
Plaintext
Raw Normal View History

ath79: Add support for Sophos AP15C The Sophos AP15C uses the same hardware as the AP15, but has a reset button. Based on: commit 6f1efb289837 ("ath79: add support for Sophos AP100/AP55 family") author Andrew Powers-Holmes <andrew@omnom.net> Fri, 3 Sep 2021 15:53:57 +0200 (23:53 +1000) committer Hauke Mehrtens <hauke@hauke-m.de> Sat, 16 Apr 2022 16:59:29 +0200 (16:59 +0200) Unique to AP15C: - Reset button - External RJ45 serial console port Flashing instructions: This firmware can be flashed either via a compatible Sophos SG or XG firewall appliance, which does not require disassembling the device, or via the U-Boot console available on the internal UART header. To flash via XG appliance: - Register on Sophos' website for a no-cost Home Use XG firewall license - Download and install the XG software on a compatible PC or virtual machine, complete initial appliance setup, and enable SSH console access - Connect the target AP device to the XG appliance's LAN interface - Approve the AP from the XG Web UI and wait until it shows as Active (this can take 3-5 minutes) - Connect to the XG appliance over SSH and access the Advanced Console (Menu option 5, then menu option 3) - Run `sudo awetool` and select the menu option to connect to an AP via SSH. When prompted to enable SSH on the target AP, select Yes. - Wait 2-3 minutes, then select the AP from the awetool menu again. This will connect you to a root shell on the target AP. - Copy the firmware to /tmp/openwrt.bin on the target AP via SCP/TFTP/etc - Run `mtd -r write /tmp/openwrt.bin astaro_image` - When complete, the access point will reboot to OpenWRT. To flash via U-Boot serial console: - Configure a TFTP server on your PC, and set IP address 192.168.99.8 with netmask 255.255.255.0 - Copy the firmware .bin to the TFTP server and rename to 'uImage_AP15C' - Open the target AP's enclosure and locate the 4-pin 3.3V UART header [4] - Connect the AP ethernet to your PC's ethernet port - Connect a terminal to the UART at 115200 8/N/1 as usual - Power on the AP and press a key to cancel autoboot when prompted - Run the following commands at the U-Boot console: - `tftpboot` - `cp.b $fileaddr 0x9f070000 $filesize` - `boot` - The access point will boot to OpenWRT. Signed-off-by: David Lutz <kpanic@hirnduenger.de> (cherry picked from commit a7abc7ec3b61be553f33c49e5acc90a4d539d992)
2024-11-05 09:55:43 +00:00
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
#include "qca955x.dtsi"
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
#include <dt-bindings/leds/common.h>
/ {
compatible = "sophos,ap15c", "qca,qca9557";
model = "Sophos AP15C";
aliases {
led-boot = &led_status_green;
led-failsafe = &led_status_yellow;
led-running = &led_status_green;
led-upgrade = &led_status_yellow;
label-mac-device = &eth0;
};
chosen {
bootargs = "console=ttyS0,115200n8";
};
keys {
compatible = "gpio-keys";
reset {
label = "reset";
linux,code = <KEY_RESTART>;
gpios = <&gpio 18 GPIO_ACTIVE_LOW>;
debounce-interval = <60>;
};
};
leds {
compatible = "gpio-leds";
led_status_green: status_green {
function = LED_FUNCTION_STATUS;
color = <LED_COLOR_ID_GREEN>;
gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
default-state = "on";
};
led_status_yellow: status_yellow {
function = LED_FUNCTION_STATUS;
color = <LED_COLOR_ID_YELLOW>;
gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
};
};
};
&spi {
status = "okay";
flash@0 {
compatible = "jedec,spi-nor";
reg = <0>;
spi-max-frequency = <25000000>;
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
partition@0 {
label = "u-boot";
reg = <0x000000 0x040000>;
read-only;
};
partition@40000 {
label = "u-boot-env";
reg = <0x040000 0x010000>;
};
partition@50000 {
label = "art";
reg = <0x050000 0x010000>;
read-only;
nvmem-layout {
compatible = "fixed-layout";
#address-cells = <1>;
#size-cells = <1>;
cal_art_1000: calibration@1000 {
reg = <0x1000 0x440>;
};
};
};
partition@60000 {
label = "config";
reg = <0x060000 0x010000>;
read-only;
nvmem-layout {
compatible = "fixed-layout";
#address-cells = <1>;
#size-cells = <1>;
macaddr_config_201a: macaddr@201a {
reg = <0x201a 0x6>;
};
};
};
partition@70000 {
compatible = "denx,uimage";
label = "firmware";
reg = <0x070000 0xf90000>;
};
};
};
};
&mdio0 {
status = "okay";
phy-mask = <0x10>;
phy4: ethernet-phy@4 {
reg = <4>;
eee-broken-100tx;
eee-broken-1000t;
};
};
&eth0 {
status = "okay";
pll-data = <0xa6000000 0xa0000101 0xa0001313>;
nvmem-cells = <&macaddr_config_201a>;
nvmem-cell-names = "mac-address";
phy-mode = "rgmii-id";
phy-handle = <&phy4>;
gmac_config: gmac-config {
device = <&gmac>;
rgmii-enabled = <1>;
rxdv-delay = <3>;
rxd-delay = <3>;
txen-delay = <3>;
txd-delay = <3>;
};
};
&wmac {
status = "okay";
nvmem-cells = <&cal_art_1000>;
nvmem-cell-names = "calibration";
};