openwrt/target/linux/mediatek/dts/mt7622-ubnt-unifi-6-lr.dts

84 lines
1.3 KiB
Plaintext
Raw Normal View History

mediatek: add support for Ubiquiti UniFi 6 LR Hardware -------- MediaTek MT7622 512MB DDR3 RAM 64M SPI-NOR Flash (Winbond W25Q512JV) MediaTek MT7622 802.11bgn 4T4R WMAC MediaTek MT7915 802.11ax 4T4R Marvell AQR1112 100/1000/2500 NBase-T PHY Holtek HT32F52241 LED controller Reset Switch UART ---- CPU UART0 at the pinout next to the Holtek MCU. Pinout (first pin next to SoC / MCU) 0 3V3 1 RX 2 TX 3 GND Settings are 115200 8N1. Opening the case ---------------- Opening the case is not a nice task, as itis glued together. Insert a flat knife between the front and back casing below the ethernet port. Open up a gap this way and insert a flat scredriver, remove the knife. Work your way around the casing by applying force to seperate the front and back casing. This losens the glue and opens the plastic clips. Be gentle, as these clips are very cheap and break quickly. Installation ------------ 1. Connect to the booted device at 192.168.1.20 using username/password "ubnt". 2. Transfer the OpenWrt sysupgrade image to the device using SCP. 3. Check the mtd partition number for bs / kernel0 / kernel1 $ cat /proc/mtd 4. Set the bootselect flag to boot from kernel0 $ dd if=/dev/zero bs=1 count=1 of=/dev/mtdblock6 5. Write the OpenWrt sysupgrade image to both kernel0 as well as kernel1 $ dd if=openwrt.bin of=/dev/mtdblock8 $ dd if=openwrt.bin of=/dev/mtdblock9 6. Reboot the device. It should boot into OpenWrt. Signed-off-by: David Bauer <mail@david-bauer.net> Signed-off-by: maurerr <mariusd84@gmail.com>
2021-02-11 16:09:06 +00:00
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
#include "mt7622-ubnt-unifi-6-lr.dtsi"
mediatek: add support for Ubiquiti UniFi 6 LR Hardware -------- MediaTek MT7622 512MB DDR3 RAM 64M SPI-NOR Flash (Winbond W25Q512JV) MediaTek MT7622 802.11bgn 4T4R WMAC MediaTek MT7915 802.11ax 4T4R Marvell AQR1112 100/1000/2500 NBase-T PHY Holtek HT32F52241 LED controller Reset Switch UART ---- CPU UART0 at the pinout next to the Holtek MCU. Pinout (first pin next to SoC / MCU) 0 3V3 1 RX 2 TX 3 GND Settings are 115200 8N1. Opening the case ---------------- Opening the case is not a nice task, as itis glued together. Insert a flat knife between the front and back casing below the ethernet port. Open up a gap this way and insert a flat scredriver, remove the knife. Work your way around the casing by applying force to seperate the front and back casing. This losens the glue and opens the plastic clips. Be gentle, as these clips are very cheap and break quickly. Installation ------------ 1. Connect to the booted device at 192.168.1.20 using username/password "ubnt". 2. Transfer the OpenWrt sysupgrade image to the device using SCP. 3. Check the mtd partition number for bs / kernel0 / kernel1 $ cat /proc/mtd 4. Set the bootselect flag to boot from kernel0 $ dd if=/dev/zero bs=1 count=1 of=/dev/mtdblock6 5. Write the OpenWrt sysupgrade image to both kernel0 as well as kernel1 $ dd if=openwrt.bin of=/dev/mtdblock8 $ dd if=openwrt.bin of=/dev/mtdblock9 6. Reboot the device. It should boot into OpenWrt. Signed-off-by: David Bauer <mail@david-bauer.net> Signed-off-by: maurerr <mariusd84@gmail.com>
2021-02-11 16:09:06 +00:00
/ {
model = "Ubiquiti UniFi 6 LR";
compatible = "ubnt,unifi-6-lr", "mediatek,mt7622";
};
&nor_partitions {
partition@0 {
label = "preloader";
reg = <0x0 0x40000>;
};
mediatek: add support for Ubiquiti UniFi 6 LR Hardware -------- MediaTek MT7622 512MB DDR3 RAM 64M SPI-NOR Flash (Winbond W25Q512JV) MediaTek MT7622 802.11bgn 4T4R WMAC MediaTek MT7915 802.11ax 4T4R Marvell AQR1112 100/1000/2500 NBase-T PHY Holtek HT32F52241 LED controller Reset Switch UART ---- CPU UART0 at the pinout next to the Holtek MCU. Pinout (first pin next to SoC / MCU) 0 3V3 1 RX 2 TX 3 GND Settings are 115200 8N1. Opening the case ---------------- Opening the case is not a nice task, as itis glued together. Insert a flat knife between the front and back casing below the ethernet port. Open up a gap this way and insert a flat scredriver, remove the knife. Work your way around the casing by applying force to seperate the front and back casing. This losens the glue and opens the plastic clips. Be gentle, as these clips are very cheap and break quickly. Installation ------------ 1. Connect to the booted device at 192.168.1.20 using username/password "ubnt". 2. Transfer the OpenWrt sysupgrade image to the device using SCP. 3. Check the mtd partition number for bs / kernel0 / kernel1 $ cat /proc/mtd 4. Set the bootselect flag to boot from kernel0 $ dd if=/dev/zero bs=1 count=1 of=/dev/mtdblock6 5. Write the OpenWrt sysupgrade image to both kernel0 as well as kernel1 $ dd if=openwrt.bin of=/dev/mtdblock8 $ dd if=openwrt.bin of=/dev/mtdblock9 6. Reboot the device. It should boot into OpenWrt. Signed-off-by: David Bauer <mail@david-bauer.net> Signed-off-by: maurerr <mariusd84@gmail.com>
2021-02-11 16:09:06 +00:00
partition@40000 {
label = "atf";
reg = <0x40000 0x20000>;
mediatek: add support for Ubiquiti UniFi 6 LR Hardware -------- MediaTek MT7622 512MB DDR3 RAM 64M SPI-NOR Flash (Winbond W25Q512JV) MediaTek MT7622 802.11bgn 4T4R WMAC MediaTek MT7915 802.11ax 4T4R Marvell AQR1112 100/1000/2500 NBase-T PHY Holtek HT32F52241 LED controller Reset Switch UART ---- CPU UART0 at the pinout next to the Holtek MCU. Pinout (first pin next to SoC / MCU) 0 3V3 1 RX 2 TX 3 GND Settings are 115200 8N1. Opening the case ---------------- Opening the case is not a nice task, as itis glued together. Insert a flat knife between the front and back casing below the ethernet port. Open up a gap this way and insert a flat scredriver, remove the knife. Work your way around the casing by applying force to seperate the front and back casing. This losens the glue and opens the plastic clips. Be gentle, as these clips are very cheap and break quickly. Installation ------------ 1. Connect to the booted device at 192.168.1.20 using username/password "ubnt". 2. Transfer the OpenWrt sysupgrade image to the device using SCP. 3. Check the mtd partition number for bs / kernel0 / kernel1 $ cat /proc/mtd 4. Set the bootselect flag to boot from kernel0 $ dd if=/dev/zero bs=1 count=1 of=/dev/mtdblock6 5. Write the OpenWrt sysupgrade image to both kernel0 as well as kernel1 $ dd if=openwrt.bin of=/dev/mtdblock8 $ dd if=openwrt.bin of=/dev/mtdblock9 6. Reboot the device. It should boot into OpenWrt. Signed-off-by: David Bauer <mail@david-bauer.net> Signed-off-by: maurerr <mariusd84@gmail.com>
2021-02-11 16:09:06 +00:00
};
partition@60000 {
label = "u-boot";
reg = <0x60000 0x60000>;
mediatek: add support for Ubiquiti UniFi 6 LR Hardware -------- MediaTek MT7622 512MB DDR3 RAM 64M SPI-NOR Flash (Winbond W25Q512JV) MediaTek MT7622 802.11bgn 4T4R WMAC MediaTek MT7915 802.11ax 4T4R Marvell AQR1112 100/1000/2500 NBase-T PHY Holtek HT32F52241 LED controller Reset Switch UART ---- CPU UART0 at the pinout next to the Holtek MCU. Pinout (first pin next to SoC / MCU) 0 3V3 1 RX 2 TX 3 GND Settings are 115200 8N1. Opening the case ---------------- Opening the case is not a nice task, as itis glued together. Insert a flat knife between the front and back casing below the ethernet port. Open up a gap this way and insert a flat scredriver, remove the knife. Work your way around the casing by applying force to seperate the front and back casing. This losens the glue and opens the plastic clips. Be gentle, as these clips are very cheap and break quickly. Installation ------------ 1. Connect to the booted device at 192.168.1.20 using username/password "ubnt". 2. Transfer the OpenWrt sysupgrade image to the device using SCP. 3. Check the mtd partition number for bs / kernel0 / kernel1 $ cat /proc/mtd 4. Set the bootselect flag to boot from kernel0 $ dd if=/dev/zero bs=1 count=1 of=/dev/mtdblock6 5. Write the OpenWrt sysupgrade image to both kernel0 as well as kernel1 $ dd if=openwrt.bin of=/dev/mtdblock8 $ dd if=openwrt.bin of=/dev/mtdblock9 6. Reboot the device. It should boot into OpenWrt. Signed-off-by: David Bauer <mail@david-bauer.net> Signed-off-by: maurerr <mariusd84@gmail.com>
2021-02-11 16:09:06 +00:00
};
partition@c0000 {
label = "u-boot-env";
reg = <0xc0000 0x10000>;
};
mediatek: add support for Ubiquiti UniFi 6 LR Hardware -------- MediaTek MT7622 512MB DDR3 RAM 64M SPI-NOR Flash (Winbond W25Q512JV) MediaTek MT7622 802.11bgn 4T4R WMAC MediaTek MT7915 802.11ax 4T4R Marvell AQR1112 100/1000/2500 NBase-T PHY Holtek HT32F52241 LED controller Reset Switch UART ---- CPU UART0 at the pinout next to the Holtek MCU. Pinout (first pin next to SoC / MCU) 0 3V3 1 RX 2 TX 3 GND Settings are 115200 8N1. Opening the case ---------------- Opening the case is not a nice task, as itis glued together. Insert a flat knife between the front and back casing below the ethernet port. Open up a gap this way and insert a flat scredriver, remove the knife. Work your way around the casing by applying force to seperate the front and back casing. This losens the glue and opens the plastic clips. Be gentle, as these clips are very cheap and break quickly. Installation ------------ 1. Connect to the booted device at 192.168.1.20 using username/password "ubnt". 2. Transfer the OpenWrt sysupgrade image to the device using SCP. 3. Check the mtd partition number for bs / kernel0 / kernel1 $ cat /proc/mtd 4. Set the bootselect flag to boot from kernel0 $ dd if=/dev/zero bs=1 count=1 of=/dev/mtdblock6 5. Write the OpenWrt sysupgrade image to both kernel0 as well as kernel1 $ dd if=openwrt.bin of=/dev/mtdblock8 $ dd if=openwrt.bin of=/dev/mtdblock9 6. Reboot the device. It should boot into OpenWrt. Signed-off-by: David Bauer <mail@david-bauer.net> Signed-off-by: maurerr <mariusd84@gmail.com>
2021-02-11 16:09:06 +00:00
factory: partition@d0000 {
label = "factory";
reg = <0xd0000 0x40000>;
read-only;
mediatek: add support for Ubiquiti UniFi 6 LR Hardware -------- MediaTek MT7622 512MB DDR3 RAM 64M SPI-NOR Flash (Winbond W25Q512JV) MediaTek MT7622 802.11bgn 4T4R WMAC MediaTek MT7915 802.11ax 4T4R Marvell AQR1112 100/1000/2500 NBase-T PHY Holtek HT32F52241 LED controller Reset Switch UART ---- CPU UART0 at the pinout next to the Holtek MCU. Pinout (first pin next to SoC / MCU) 0 3V3 1 RX 2 TX 3 GND Settings are 115200 8N1. Opening the case ---------------- Opening the case is not a nice task, as itis glued together. Insert a flat knife between the front and back casing below the ethernet port. Open up a gap this way and insert a flat scredriver, remove the knife. Work your way around the casing by applying force to seperate the front and back casing. This losens the glue and opens the plastic clips. Be gentle, as these clips are very cheap and break quickly. Installation ------------ 1. Connect to the booted device at 192.168.1.20 using username/password "ubnt". 2. Transfer the OpenWrt sysupgrade image to the device using SCP. 3. Check the mtd partition number for bs / kernel0 / kernel1 $ cat /proc/mtd 4. Set the bootselect flag to boot from kernel0 $ dd if=/dev/zero bs=1 count=1 of=/dev/mtdblock6 5. Write the OpenWrt sysupgrade image to both kernel0 as well as kernel1 $ dd if=openwrt.bin of=/dev/mtdblock8 $ dd if=openwrt.bin of=/dev/mtdblock9 6. Reboot the device. It should boot into OpenWrt. Signed-off-by: David Bauer <mail@david-bauer.net> Signed-off-by: maurerr <mariusd84@gmail.com>
2021-02-11 16:09:06 +00:00
};
eeprom: partition@110000 {
label = "eeprom";
reg = <0x110000 0x10000>;
read-only;
};
mediatek: add support for Ubiquiti UniFi 6 LR Hardware -------- MediaTek MT7622 512MB DDR3 RAM 64M SPI-NOR Flash (Winbond W25Q512JV) MediaTek MT7622 802.11bgn 4T4R WMAC MediaTek MT7915 802.11ax 4T4R Marvell AQR1112 100/1000/2500 NBase-T PHY Holtek HT32F52241 LED controller Reset Switch UART ---- CPU UART0 at the pinout next to the Holtek MCU. Pinout (first pin next to SoC / MCU) 0 3V3 1 RX 2 TX 3 GND Settings are 115200 8N1. Opening the case ---------------- Opening the case is not a nice task, as itis glued together. Insert a flat knife between the front and back casing below the ethernet port. Open up a gap this way and insert a flat scredriver, remove the knife. Work your way around the casing by applying force to seperate the front and back casing. This losens the glue and opens the plastic clips. Be gentle, as these clips are very cheap and break quickly. Installation ------------ 1. Connect to the booted device at 192.168.1.20 using username/password "ubnt". 2. Transfer the OpenWrt sysupgrade image to the device using SCP. 3. Check the mtd partition number for bs / kernel0 / kernel1 $ cat /proc/mtd 4. Set the bootselect flag to boot from kernel0 $ dd if=/dev/zero bs=1 count=1 of=/dev/mtdblock6 5. Write the OpenWrt sysupgrade image to both kernel0 as well as kernel1 $ dd if=openwrt.bin of=/dev/mtdblock8 $ dd if=openwrt.bin of=/dev/mtdblock9 6. Reboot the device. It should boot into OpenWrt. Signed-off-by: David Bauer <mail@david-bauer.net> Signed-off-by: maurerr <mariusd84@gmail.com>
2021-02-11 16:09:06 +00:00
partition@120000 {
label = "bs";
reg = <0x120000 0x10000>;
mediatek: add support for Ubiquiti UniFi 6 LR Hardware -------- MediaTek MT7622 512MB DDR3 RAM 64M SPI-NOR Flash (Winbond W25Q512JV) MediaTek MT7622 802.11bgn 4T4R WMAC MediaTek MT7915 802.11ax 4T4R Marvell AQR1112 100/1000/2500 NBase-T PHY Holtek HT32F52241 LED controller Reset Switch UART ---- CPU UART0 at the pinout next to the Holtek MCU. Pinout (first pin next to SoC / MCU) 0 3V3 1 RX 2 TX 3 GND Settings are 115200 8N1. Opening the case ---------------- Opening the case is not a nice task, as itis glued together. Insert a flat knife between the front and back casing below the ethernet port. Open up a gap this way and insert a flat scredriver, remove the knife. Work your way around the casing by applying force to seperate the front and back casing. This losens the glue and opens the plastic clips. Be gentle, as these clips are very cheap and break quickly. Installation ------------ 1. Connect to the booted device at 192.168.1.20 using username/password "ubnt". 2. Transfer the OpenWrt sysupgrade image to the device using SCP. 3. Check the mtd partition number for bs / kernel0 / kernel1 $ cat /proc/mtd 4. Set the bootselect flag to boot from kernel0 $ dd if=/dev/zero bs=1 count=1 of=/dev/mtdblock6 5. Write the OpenWrt sysupgrade image to both kernel0 as well as kernel1 $ dd if=openwrt.bin of=/dev/mtdblock8 $ dd if=openwrt.bin of=/dev/mtdblock9 6. Reboot the device. It should boot into OpenWrt. Signed-off-by: David Bauer <mail@david-bauer.net> Signed-off-by: maurerr <mariusd84@gmail.com>
2021-02-11 16:09:06 +00:00
};
partition@130000 {
label = "cfg";
reg = <0x130000 0x100000>;
read-only;
mediatek: add support for Ubiquiti UniFi 6 LR Hardware -------- MediaTek MT7622 512MB DDR3 RAM 64M SPI-NOR Flash (Winbond W25Q512JV) MediaTek MT7622 802.11bgn 4T4R WMAC MediaTek MT7915 802.11ax 4T4R Marvell AQR1112 100/1000/2500 NBase-T PHY Holtek HT32F52241 LED controller Reset Switch UART ---- CPU UART0 at the pinout next to the Holtek MCU. Pinout (first pin next to SoC / MCU) 0 3V3 1 RX 2 TX 3 GND Settings are 115200 8N1. Opening the case ---------------- Opening the case is not a nice task, as itis glued together. Insert a flat knife between the front and back casing below the ethernet port. Open up a gap this way and insert a flat scredriver, remove the knife. Work your way around the casing by applying force to seperate the front and back casing. This losens the glue and opens the plastic clips. Be gentle, as these clips are very cheap and break quickly. Installation ------------ 1. Connect to the booted device at 192.168.1.20 using username/password "ubnt". 2. Transfer the OpenWrt sysupgrade image to the device using SCP. 3. Check the mtd partition number for bs / kernel0 / kernel1 $ cat /proc/mtd 4. Set the bootselect flag to boot from kernel0 $ dd if=/dev/zero bs=1 count=1 of=/dev/mtdblock6 5. Write the OpenWrt sysupgrade image to both kernel0 as well as kernel1 $ dd if=openwrt.bin of=/dev/mtdblock8 $ dd if=openwrt.bin of=/dev/mtdblock9 6. Reboot the device. It should boot into OpenWrt. Signed-off-by: David Bauer <mail@david-bauer.net> Signed-off-by: maurerr <mariusd84@gmail.com>
2021-02-11 16:09:06 +00:00
};
partition@230000 {
compatible = "denx,fit";
label = "firmware";
reg = <0x230000 0x1ee0000>;
mediatek: add support for Ubiquiti UniFi 6 LR Hardware -------- MediaTek MT7622 512MB DDR3 RAM 64M SPI-NOR Flash (Winbond W25Q512JV) MediaTek MT7622 802.11bgn 4T4R WMAC MediaTek MT7915 802.11ax 4T4R Marvell AQR1112 100/1000/2500 NBase-T PHY Holtek HT32F52241 LED controller Reset Switch UART ---- CPU UART0 at the pinout next to the Holtek MCU. Pinout (first pin next to SoC / MCU) 0 3V3 1 RX 2 TX 3 GND Settings are 115200 8N1. Opening the case ---------------- Opening the case is not a nice task, as itis glued together. Insert a flat knife between the front and back casing below the ethernet port. Open up a gap this way and insert a flat scredriver, remove the knife. Work your way around the casing by applying force to seperate the front and back casing. This losens the glue and opens the plastic clips. Be gentle, as these clips are very cheap and break quickly. Installation ------------ 1. Connect to the booted device at 192.168.1.20 using username/password "ubnt". 2. Transfer the OpenWrt sysupgrade image to the device using SCP. 3. Check the mtd partition number for bs / kernel0 / kernel1 $ cat /proc/mtd 4. Set the bootselect flag to boot from kernel0 $ dd if=/dev/zero bs=1 count=1 of=/dev/mtdblock6 5. Write the OpenWrt sysupgrade image to both kernel0 as well as kernel1 $ dd if=openwrt.bin of=/dev/mtdblock8 $ dd if=openwrt.bin of=/dev/mtdblock9 6. Reboot the device. It should boot into OpenWrt. Signed-off-by: David Bauer <mail@david-bauer.net> Signed-off-by: maurerr <mariusd84@gmail.com>
2021-02-11 16:09:06 +00:00
};
partition@2110000 {
label = "kernel1";
reg = <0x2110000 0x1ee0000>;
mediatek: add support for Ubiquiti UniFi 6 LR Hardware -------- MediaTek MT7622 512MB DDR3 RAM 64M SPI-NOR Flash (Winbond W25Q512JV) MediaTek MT7622 802.11bgn 4T4R WMAC MediaTek MT7915 802.11ax 4T4R Marvell AQR1112 100/1000/2500 NBase-T PHY Holtek HT32F52241 LED controller Reset Switch UART ---- CPU UART0 at the pinout next to the Holtek MCU. Pinout (first pin next to SoC / MCU) 0 3V3 1 RX 2 TX 3 GND Settings are 115200 8N1. Opening the case ---------------- Opening the case is not a nice task, as itis glued together. Insert a flat knife between the front and back casing below the ethernet port. Open up a gap this way and insert a flat scredriver, remove the knife. Work your way around the casing by applying force to seperate the front and back casing. This losens the glue and opens the plastic clips. Be gentle, as these clips are very cheap and break quickly. Installation ------------ 1. Connect to the booted device at 192.168.1.20 using username/password "ubnt". 2. Transfer the OpenWrt sysupgrade image to the device using SCP. 3. Check the mtd partition number for bs / kernel0 / kernel1 $ cat /proc/mtd 4. Set the bootselect flag to boot from kernel0 $ dd if=/dev/zero bs=1 count=1 of=/dev/mtdblock6 5. Write the OpenWrt sysupgrade image to both kernel0 as well as kernel1 $ dd if=openwrt.bin of=/dev/mtdblock8 $ dd if=openwrt.bin of=/dev/mtdblock9 6. Reboot the device. It should boot into OpenWrt. Signed-off-by: David Bauer <mail@david-bauer.net> Signed-off-by: maurerr <mariusd84@gmail.com>
2021-02-11 16:09:06 +00:00
};
};
&wmac {
mediatek,mtd-eeprom = <&factory 0x0>;
mtd-mac-address = <&eeprom 0x0>;
mediatek: add support for Ubiquiti UniFi 6 LR Hardware -------- MediaTek MT7622 512MB DDR3 RAM 64M SPI-NOR Flash (Winbond W25Q512JV) MediaTek MT7622 802.11bgn 4T4R WMAC MediaTek MT7915 802.11ax 4T4R Marvell AQR1112 100/1000/2500 NBase-T PHY Holtek HT32F52241 LED controller Reset Switch UART ---- CPU UART0 at the pinout next to the Holtek MCU. Pinout (first pin next to SoC / MCU) 0 3V3 1 RX 2 TX 3 GND Settings are 115200 8N1. Opening the case ---------------- Opening the case is not a nice task, as itis glued together. Insert a flat knife between the front and back casing below the ethernet port. Open up a gap this way and insert a flat scredriver, remove the knife. Work your way around the casing by applying force to seperate the front and back casing. This losens the glue and opens the plastic clips. Be gentle, as these clips are very cheap and break quickly. Installation ------------ 1. Connect to the booted device at 192.168.1.20 using username/password "ubnt". 2. Transfer the OpenWrt sysupgrade image to the device using SCP. 3. Check the mtd partition number for bs / kernel0 / kernel1 $ cat /proc/mtd 4. Set the bootselect flag to boot from kernel0 $ dd if=/dev/zero bs=1 count=1 of=/dev/mtdblock6 5. Write the OpenWrt sysupgrade image to both kernel0 as well as kernel1 $ dd if=openwrt.bin of=/dev/mtdblock8 $ dd if=openwrt.bin of=/dev/mtdblock9 6. Reboot the device. It should boot into OpenWrt. Signed-off-by: David Bauer <mail@david-bauer.net> Signed-off-by: maurerr <mariusd84@gmail.com>
2021-02-11 16:09:06 +00:00
status = "okay";
};
&slot0 {
wifi@0,0 {
reg = <0x0 0 0 0 0>;
mediatek,mtd-eeprom = <&factory 0x20000>;
mtd-mac-address = <&eeprom 0x6>;
ieee80211-freq-limit = <5000000 6000000>;
};
};
&gmac0 {
mediatek: add support for Ubiquiti UniFi 6 LR Hardware -------- MediaTek MT7622 512MB DDR3 RAM 64M SPI-NOR Flash (Winbond W25Q512JV) MediaTek MT7622 802.11bgn 4T4R WMAC MediaTek MT7915 802.11ax 4T4R Marvell AQR1112 100/1000/2500 NBase-T PHY Holtek HT32F52241 LED controller Reset Switch UART ---- CPU UART0 at the pinout next to the Holtek MCU. Pinout (first pin next to SoC / MCU) 0 3V3 1 RX 2 TX 3 GND Settings are 115200 8N1. Opening the case ---------------- Opening the case is not a nice task, as itis glued together. Insert a flat knife between the front and back casing below the ethernet port. Open up a gap this way and insert a flat scredriver, remove the knife. Work your way around the casing by applying force to seperate the front and back casing. This losens the glue and opens the plastic clips. Be gentle, as these clips are very cheap and break quickly. Installation ------------ 1. Connect to the booted device at 192.168.1.20 using username/password "ubnt". 2. Transfer the OpenWrt sysupgrade image to the device using SCP. 3. Check the mtd partition number for bs / kernel0 / kernel1 $ cat /proc/mtd 4. Set the bootselect flag to boot from kernel0 $ dd if=/dev/zero bs=1 count=1 of=/dev/mtdblock6 5. Write the OpenWrt sysupgrade image to both kernel0 as well as kernel1 $ dd if=openwrt.bin of=/dev/mtdblock8 $ dd if=openwrt.bin of=/dev/mtdblock9 6. Reboot the device. It should boot into OpenWrt. Signed-off-by: David Bauer <mail@david-bauer.net> Signed-off-by: maurerr <mariusd84@gmail.com>
2021-02-11 16:09:06 +00:00
mtd-mac-address = <&eeprom 0x0>;
};