ExternalVendorCode/openwrt
1
0
Fork 0
mirror of https://github.com/openwrt/openwrt.git synced 2024-12-27 01:11:14 +00:00
Code Issues Actions 4 Packages Projects Releases Wiki Activity
9c7025b779
openwrt/target/linux/ipq40xx/patches-4.19/901-arm-boot-add-dts-files.patch

52 lines
1.6 KiB
Diff
Raw Normal View History

ipq40xx: Add support for Unielec U4019 This commit adds support for the 32MB storage/512MB RAM version of the U4019 IPQ4019-based board from Unielec. The board has the following specifications: * Qualcomm IPQ4019 (running at 717MHz) * 512MB DDR3 RAM (optional 256MB/1GB) * 32MB SPI NOR (optional 8/16MB or NAND) * Five gigabit ports (Qualcomm QCA8075) * 1x 2.4 GHz wifi (QCA4019 hw1.0) * 1x 5 Ghz wifi (QCA4019 hw1.0) * 1x mini-PCIe slot (only USB-pins connected) * 1x SIM slot (mini-SIM) * 1x USB2.0 port * 1x button * 1x controllable LED * 1x micro SD-card reader Working: * Ethernet * Wifi * USB-port * mini-PCIe slot + SIM slot * Button * Sysupgrade Not working: * SD card slot (no upstream support) Installation instructions: In order to install OpenWRT on the U4019, you need to go via the initramfs-image. The installation steps are as follows: * Connect to board via serial (header exposed and clearly marked). * Interrupt bootloader by pressing a button. * Copy the initramfs-image to your tftp folder, call the file C0A80079.img. * Give the network interface connected to the U4019 the address 192.168.0.156/24. * Start your tftp-server and run tftpboot on the board. * Run bootm when the file has been transferred, to boot OpenWRT. * Once OpenWRT has booted, copy the sysupgrade-image to the device and run sysupgrade to install OpenWRT on the U4019. Notes: - Since IPQ4019 has been moved to 4.19, I have not added support for kernel 4.14. - There is a bug with hardware encryption on IPQ4019, causing poor performance with TCP and ipsec (see for example FS#2355). In order to improve performance, I have disabled hardware encryption in the DTS. We can enable hw. enc. once/if bug is fixed. - In order for Ethernet to work, the phy has to be reset by setting gpio 47 low/high. Adding support for phy reset via gpio required patching the mdio-driver, and the code added comes from the vendor driver. I do not know if patching the driver is an acceptable approach or not. v1->v2: * Do not use wildcard as identifier in the board.d-scripts (thanks Adrian Schmutzler). Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
2019-10-20 09:33:13 +00:00
From a10fab12a927e60b7141a602e740d70cb4d09e4a Mon Sep 17 00:00:00 2001
ipq40xx: Add patches for 4.19 This adds the necessary patches for 4.19 kernel. Upstreamed patches were dropped, backported upstreamed patches from 4.20. Drop Winbond ID patch since that NAND IC was upstreamed to use SPI-NAND framework and support for it was backported from 4.20. Rework ESSEDMA patches to compile under 4.19 due to timer changes, Clément Péron did the hard work and his changes were taken from the initial 4.19 PR. MR33 changes had to be manually refreshed to apply. Refresh other patches to apply. Signed-off-by: Robert Marko <robimarko@gmail.com> Remove
2018-12-17 09:39:09 +00:00
From: John Crispin <john@phrozen.org>
Date: Thu, 9 Mar 2017 11:03:18 +0100
ipq40xx: Add support for Unielec U4019 This commit adds support for the 32MB storage/512MB RAM version of the U4019 IPQ4019-based board from Unielec. The board has the following specifications: * Qualcomm IPQ4019 (running at 717MHz) * 512MB DDR3 RAM (optional 256MB/1GB) * 32MB SPI NOR (optional 8/16MB or NAND) * Five gigabit ports (Qualcomm QCA8075) * 1x 2.4 GHz wifi (QCA4019 hw1.0) * 1x 5 Ghz wifi (QCA4019 hw1.0) * 1x mini-PCIe slot (only USB-pins connected) * 1x SIM slot (mini-SIM) * 1x USB2.0 port * 1x button * 1x controllable LED * 1x micro SD-card reader Working: * Ethernet * Wifi * USB-port * mini-PCIe slot + SIM slot * Button * Sysupgrade Not working: * SD card slot (no upstream support) Installation instructions: In order to install OpenWRT on the U4019, you need to go via the initramfs-image. The installation steps are as follows: * Connect to board via serial (header exposed and clearly marked). * Interrupt bootloader by pressing a button. * Copy the initramfs-image to your tftp folder, call the file C0A80079.img. * Give the network interface connected to the U4019 the address 192.168.0.156/24. * Start your tftp-server and run tftpboot on the board. * Run bootm when the file has been transferred, to boot OpenWRT. * Once OpenWRT has booted, copy the sysupgrade-image to the device and run sysupgrade to install OpenWRT on the U4019. Notes: - Since IPQ4019 has been moved to 4.19, I have not added support for kernel 4.14. - There is a bug with hardware encryption on IPQ4019, causing poor performance with TCP and ipsec (see for example FS#2355). In order to improve performance, I have disabled hardware encryption in the DTS. We can enable hw. enc. once/if bug is fixed. - In order for Ethernet to work, the phy has to be reset by setting gpio 47 low/high. Adding support for phy reset via gpio required patching the mdio-driver, and the code added comes from the vendor driver. I do not know if patching the driver is an acceptable approach or not. v1->v2: * Do not use wildcard as identifier in the board.d-scripts (thanks Adrian Schmutzler). Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
2019-10-20 09:33:13 +00:00
Subject: [PATCH] arm: boot: add dts files
ipq40xx: Add patches for 4.19 This adds the necessary patches for 4.19 kernel. Upstreamed patches were dropped, backported upstreamed patches from 4.20. Drop Winbond ID patch since that NAND IC was upstreamed to use SPI-NAND framework and support for it was backported from 4.20. Rework ESSEDMA patches to compile under 4.19 due to timer changes, Clément Péron did the hard work and his changes were taken from the initial 4.19 PR. MR33 changes had to be manually refreshed to apply. Refresh other patches to apply. Signed-off-by: Robert Marko <robimarko@gmail.com> Remove
2018-12-17 09:39:09 +00:00
Signed-off-by: John Crispin <john@phrozen.org>
---
ipq40xx: Add support for Unielec U4019 This commit adds support for the 32MB storage/512MB RAM version of the U4019 IPQ4019-based board from Unielec. The board has the following specifications: * Qualcomm IPQ4019 (running at 717MHz) * 512MB DDR3 RAM (optional 256MB/1GB) * 32MB SPI NOR (optional 8/16MB or NAND) * Five gigabit ports (Qualcomm QCA8075) * 1x 2.4 GHz wifi (QCA4019 hw1.0) * 1x 5 Ghz wifi (QCA4019 hw1.0) * 1x mini-PCIe slot (only USB-pins connected) * 1x SIM slot (mini-SIM) * 1x USB2.0 port * 1x button * 1x controllable LED * 1x micro SD-card reader Working: * Ethernet * Wifi * USB-port * mini-PCIe slot + SIM slot * Button * Sysupgrade Not working: * SD card slot (no upstream support) Installation instructions: In order to install OpenWRT on the U4019, you need to go via the initramfs-image. The installation steps are as follows: * Connect to board via serial (header exposed and clearly marked). * Interrupt bootloader by pressing a button. * Copy the initramfs-image to your tftp folder, call the file C0A80079.img. * Give the network interface connected to the U4019 the address 192.168.0.156/24. * Start your tftp-server and run tftpboot on the board. * Run bootm when the file has been transferred, to boot OpenWRT. * Once OpenWRT has booted, copy the sysupgrade-image to the device and run sysupgrade to install OpenWRT on the U4019. Notes: - Since IPQ4019 has been moved to 4.19, I have not added support for kernel 4.14. - There is a bug with hardware encryption on IPQ4019, causing poor performance with TCP and ipsec (see for example FS#2355). In order to improve performance, I have disabled hardware encryption in the DTS. We can enable hw. enc. once/if bug is fixed. - In order for Ethernet to work, the phy has to be reset by setting gpio 47 low/high. Adding support for phy reset via gpio required patching the mdio-driver, and the code added comes from the vendor driver. I do not know if patching the driver is an acceptable approach or not. v1->v2: * Do not use wildcard as identifier in the board.d-scripts (thanks Adrian Schmutzler). Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
2019-10-20 09:33:13 +00:00
arch/arm/boot/dts/Makefile | 23 +++++++++++++++++++++++
1 file changed, 23 insertions(+)
ipq40xx: Add patches for 4.19 This adds the necessary patches for 4.19 kernel. Upstreamed patches were dropped, backported upstreamed patches from 4.20. Drop Winbond ID patch since that NAND IC was upstreamed to use SPI-NAND framework and support for it was backported from 4.20. Rework ESSEDMA patches to compile under 4.19 due to timer changes, Clément Péron did the hard work and his changes were taken from the initial 4.19 PR. MR33 changes had to be manually refreshed to apply. Refresh other patches to apply. Signed-off-by: Robert Marko <robimarko@gmail.com> Remove
2018-12-17 09:39:09 +00:00
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
ipq40xx: add support for Aruba AP-303 Hardware -------- SoC: Qualcomm IPQ4029 RAM: 512M DDR3 FLASH: - 128MB NAND (Macronix MX30LF1G18AC) - 4MB SPI-NOR (Macronix MX25R3235F) TPM: Atmel AT97SC3203 BLE: Texas Instruments CC2540T attached to ttyMSM0 ETH: Atheros AR8035 LED: WiFi (amber / green) System (red / green) BTN: Reset To connect to the serial console, you can solder to the labled pads next to the USB port or use your Aruba supplied UARt adapter. Do NOT plug a standard USB cable into the Console labled USB-port! Aruba/HPE simply put UART on the micro-USB pins. You can solder yourself an adapter cable: VCC - NC D+ - TX D- - RX GND - GND The console setting in bootloader and OS is 9600 8N1. Voltage level is 3.3V. To enable a full list of commands in the U-Boot "help" command, execute the literal "diag" command. Installation ------------ 1. Get the OpenWrt initramfs image. Rename it to ipq40xx.ari and put it into the TFTP server root directory. Configure the TFTP server to be reachable at 192.168.1.75/24. Connect the machine running the TFTP server to the ethernet port of the access point. 2. Connect to the serial console. Interrupt autobooting by pressing Enter when prompted. 3. Configure the bootargs and bootcmd for OpenWrt. $ setenv bootargs_openwrt "setenv bootargs console=ttyMSM1,9600n8" $ setenv nandboot_openwrt "run bootargs_openwrt; ubi part aos1; ubi read 0x85000000 kernel; bootm 0x85000000" $ setenv ramboot_openwrt "run bootargs_openwrt; setenv ipaddr 192.168.1.105; setenv serverip 192.168.1.75; netget; set fdt_high 0x87000000; bootm" $ setenv bootcmd "run nandboot_openwrt" $ saveenv 4. Load OpenWrt into RAM: $ run ramboot_openwrt 5. After OpenWrt booted, transfer the OpenWrt sysupgrade image to the /tmp folder on the device. 6. Flash OpenWrt: $ ubidetach -p /dev/mtd1 $ ubiformat /dev/mtd1 $ sysupgrade -n /tmp/openwrt-sysupgrade.bin To go back to the stock firmware, simply reset the bootcmd in the bootloader to the original value: $ setenv bootcmd "boot" $ saveenv Signed-off-by: David Bauer <mail@david-bauer.net>
2019-10-23 20:25:14 +00:00
@@ -785,11 +785,38 @@ dtb-$(CONFIG_ARCH_QCOM) += \
ipq40xx: Add patches for 4.19 This adds the necessary patches for 4.19 kernel. Upstreamed patches were dropped, backported upstreamed patches from 4.20. Drop Winbond ID patch since that NAND IC was upstreamed to use SPI-NAND framework and support for it was backported from 4.20. Rework ESSEDMA patches to compile under 4.19 due to timer changes, Clément Péron did the hard work and his changes were taken from the initial 4.19 PR. MR33 changes had to be manually refreshed to apply. Refresh other patches to apply. Signed-off-by: Robert Marko <robimarko@gmail.com> Remove
2018-12-17 09:39:09 +00:00
qcom-apq8074-dragonboard.dtb \
qcom-apq8084-ifc6540.dtb \
qcom-apq8084-mtp.dtb \
+ qcom-ipq4018-a42.dtb \
ipq40xx: add support for ALFA Network AP120C-AC ALFA Network AP120C-AC is a dual-band ceiling AP, based on Qualcomm IPQ4018 + QCA8075 platform. Specification: - Qualcomm IPQ4018 (717 MHz) - 256 MB of RAM (DDR3) - 16 MB (SPI NOR) + 128 MB (SPI NAND) of flash - 2x Gbps Ethernet, with 802.3af PoE support in one port - 2T2R 2.4/5 GHz (IPQ4018), with ext. FEMs (QFE1952, QFE1922) - 3x U.FL connectors - 1x 1.8 dBi (Bluetooth) and 2x 3/5 dBi dual-band (Wi-Fi) antennas - Atmel/Microchip AT97SC3205T TPM module (I2C bus) - TI CC2540 Bluetooth LE module (USB 2.0 bus) - 4x LED (all driven by GPIO) - 1x button (reset) - 1x USB 2.0 (optional, not installed in indoor version) - DC jack for main power input (12 V) - UART header available on PCB (2.0 mm pitch) Flash instruction: 1. This board uses dual-image feature (128 MB NAND is divided into two 64 MB partitions: 'rootfs1' and 'rootfs2'). 2. Before update, make sure your device is running firmware no older than v1.1 (previous versions have incompatible U-Boot). 3. Use 'factory' image in vendor GUI or for sysupgrade tool, without preserving settings. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2019-01-29 17:12:51 +00:00
+ qcom-ipq4018-ap120c-ac.dtb \
ipq40xx: add support for Linksys EA6350v3 Specifications: SOC: Qualcomm IPQ4018 RAM: 256 MiB Samsung K4B2G1646F-BYK0 FLASH1: MX25L1605D 2 MB FLASH2: Winbond W25N01GV 128Mb ETH: Qualcomm QCA8075 WLAN0: Qualcomm Atheros QCA4018 2.4GHz 802.11b/g/n 2x2 WLAN1: Qualcomm Atheros QCA4018 5GHz 802.11n/ac W2 2x2 INPUT: WPS, Reset LED: Status - Green SERIAL: Header at J19, Beneath DC Power Jack 1-VCC ; 2-TX ; 3-RX; 4-GND; Serial 115200-8-N-1. Tested and working: - USB (requires extra packages) - LAN Ethernet (Correct MAC-address) - WAN Ethernet (Correct MAC-address) - 2.4 GHz WiFi (Correct MAC-address) - 5 GHz WiFi (Correct MAC-address) - Factory installation from Web UI - OpenWRT sysupgrade - LED - Reset Button Need Testing: - WPS button Install via Web UI: - Attach to a LAN port on the router. - Connect to the Linksys Smart WiFi Page (default 192.168.1.1) and login - Select the connectivity tab on the left - In the manual update box on the right - Select browse, and browse to openwrt-ipq40xx-linksys_ea6350v3-squashfs-factory.bin - Click update. - Read and accept the warning - The router LED will start blinking. When the router LED goes solid, you can now navigate to 192.168.1.1 to your new OpenWrt installation. Sysupgrade: - Flash the sysupgrade image as usual. Please: try to do a reset everytime you can (doing it with LuCI is easy and can be done in the same step). Recovery (Automatic): - If the device fails to boot after install or upgrade, whilst the unit is turned on: 1 - Wait 15 seconds 2 - Switch Off and Wait 10 seconds 3 - Switch on 4 - Repeat steps 1 to 3, 3 times then go to 5. 5 - U-boot will have now erased the failed update and switched back to the last working firmware - you should be able to access your router on LAN. Recovery (Manual): - The steps for manual recovery are the same as the generic u-boot tftp client method. Back To Stock: - Use the generic recovery using the tftp client method to flash the "civic.img". Also you can strip-and-pad the original image and use the generic "mtd" method by flashing over the "kernel" partition. * Just be careful to flash in the partition that the device is currently booted. Signed-off-by: Ryan Pannell <ryan@osukl.com> Signed-off-by: Oever González <notengobattery@gmail.com> [minor edits, removed second compatible of nand, added dtb entry to 4.19] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-01-24 03:20:55 +00:00
+ qcom-ipq4018-ea6350v3.dtb \
ipq40xx: Add patches for 4.19 This adds the necessary patches for 4.19 kernel. Upstreamed patches were dropped, backported upstreamed patches from 4.20. Drop Winbond ID patch since that NAND IC was upstreamed to use SPI-NAND framework and support for it was backported from 4.20. Rework ESSEDMA patches to compile under 4.19 due to timer changes, Clément Péron did the hard work and his changes were taken from the initial 4.19 PR. MR33 changes had to be manually refreshed to apply. Refresh other patches to apply. Signed-off-by: Robert Marko <robimarko@gmail.com> Remove
2018-12-17 09:39:09 +00:00
+ qcom-ipq4018-eap1300.dtb \
ipq40xx: add support for EnGenius ENS620EXT Hardware -------- CPU: Qualcomm IPQ4018 RAM: 256M FLASH: 32M SPI NOR W25Q256 ETH: QCA8075 WiFi2: IPQ4018 2T2R 2SS b/g/n WiFi5: IPQ4018 2T2R 2SS n/ac LED: - Power amber - LAN1(PoE) green - LAN2 green - Wi-Fi 2.4GHz green - Wi-Fi 5GHz green BTN: - WPS UART: 115200n8 3.3V J1 VCC(1) - GND(2) - TX(3) - RX(4) Added basic support to get the device up and running for a sysupgrade image only. There is currently no way back to factory firmware, so this is a one-way street to OpenWRT. Install from factory condition is convoluted, and may brick your device: 1) Enable SSH and disable the CLI on the factory device from the web user interface (Management->Advanced) 2) Reboot the device 3) Override the default, limited SSH shell: a) Get into the ssh shell: ssh admin@192.168.1.1 /bin/sh --login b) Change the dropbear script to disable the limited shell. At the empty command prompt type: sed -i '/login_ssh/s/^/#/g’ dropbear /etc/init.d/dropbear restart exit 4) ssh in to a (now-) normal OpenWRT SSH session 5) Flash your built image a) scp openwrt-ipq40xx-engenius_ens620ext-squashfs-sysupgrade.bin admin@192.168.1.1:/tmp/ b) ssh admin@192.168.1.1 c) sysupgrade -n /tmp/openwrt-ipq40xx-engenius_ens620ext-squashfs-sysupgrade.bin 6) After flash completes (it may say "Upgrade failed" followed by "Upgrade completed") and device reboots, log in to newly flashed system. Note you will now need to ssh as root rather than admin. Signed-off-by: Steve Glennon <s.glennon@cablelabs.com> [whitespace fixes, reordered partitions, removed rng node from 4.14, fixed 901-arm-boot-add-dts-files.patch] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-02-27 22:48:23 +00:00
+ qcom-ipq4018-ens620ext.dtb \
ipq40xx: Add patches for 4.19 This adds the necessary patches for 4.19 kernel. Upstreamed patches were dropped, backported upstreamed patches from 4.20. Drop Winbond ID patch since that NAND IC was upstreamed to use SPI-NAND framework and support for it was backported from 4.20. Rework ESSEDMA patches to compile under 4.19 due to timer changes, Clément Péron did the hard work and his changes were taken from the initial 4.19 PR. MR33 changes had to be manually refreshed to apply. Refresh other patches to apply. Signed-off-by: Robert Marko <robimarko@gmail.com> Remove
2018-12-17 09:39:09 +00:00
+ qcom-ipq4018-ex6100v2.dtb \
+ qcom-ipq4018-ex6150v2.dtb \
ipq40xx: build DEVICE_DTS based on SOC and device name This patch uses the SOC variable to calculate DTS names automatically based on the SOC and the device definition node name. This reduces redundancy and (by having to choose DTS name appropriately) will unify the naming of a device in different places (image/Makefile, DTS name, compatible, image name). This is supposed to make life easier for developers and reviewers. Since the kernel uses a "soc-device.dts" scheme for this target, we use this for the derivation of DEVICE_DTS, too, and rename the files not having followed it so far. Note that for some devices the kernel itself is inconsistent, leaving us with a manual overwrite for ap.dk01.1-c1 and ap.dk04.1-c1. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-12-21 00:07:06 +00:00
+ qcom-ipq4018-fritzbox-4040.dtb \
ipq40xx: Add patches for 4.19 This adds the necessary patches for 4.19 kernel. Upstreamed patches were dropped, backported upstreamed patches from 4.20. Drop Winbond ID patch since that NAND IC was upstreamed to use SPI-NAND framework and support for it was backported from 4.20. Rework ESSEDMA patches to compile under 4.19 due to timer changes, Clément Péron did the hard work and his changes were taken from the initial 4.19 PR. MR33 changes had to be manually refreshed to apply. Refresh other patches to apply. Signed-off-by: Robert Marko <robimarko@gmail.com> Remove
2018-12-17 09:39:09 +00:00
+ qcom-ipq4018-jalapeno.dtb \
ipq40xx: add support for Crisis Innovation Lab MeshPoint.One MeshPoint.One is Wi-Fi hotspot and smart IoT gateway (based upon Jalapeno module from 8Devices). MeshPoint.One (https://meshpointone.com) is a unique Wi-Fi hotspot and smart city gateway that can be installed and powered from street lighting (even solar power in the future). MeshPoint provides up to 27 hours of interrupted Wi-Fi and IoT services from internal battery even when external power is not available. MeshPoint.One can be used for disaster relief efforts in order to provide instant Wi-Fi coverage that can be easily expanded by just adding more devices that create wide area mesh network. MeshPoint.One devices have standard Luci UI for management. Features: - 1x 1Gpbs WAN - 1x 1Gbps LAN - POE input (eth0) - POE output (eth1) - Sensor for temperature, humidity and pressure (Bosch BME280) - current, voltage and power measurement via TI INA230 - Hardware real time clock - optional power via Li-Ion battery - micro USB port with USB to serial chip for easy OpenWrt terminal access - I2C header for connecting additional sensors Installation: ------------- Simply flash the sysupgrade image from stock firmware. Or use the built in Web recovery into bootloader: Hold Reset button for 5 to 20 seconds or use UART and httpd command. Web UI will appear on 192.168.2.100 by default. For web recovery use the factory.ubi image. Signed-off-by: Damir Samardzic <damir.samardzic@sartura.hr> Signed-off-by: Damir Franusic <damir.franusic@sartura.hr> Signed-off-by: Valent Turkovic <valent@meshpoint.me> Signed-off-by: Robert Marko <robert@meshpoint.me> [commit description long line wrap, usb->USB] Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-11-25 14:25:00 +00:00
+ qcom-ipq4018-meshpoint-one.dtb \
ipq40xx: Add patches for 4.19 This adds the necessary patches for 4.19 kernel. Upstreamed patches were dropped, backported upstreamed patches from 4.20. Drop Winbond ID patch since that NAND IC was upstreamed to use SPI-NAND framework and support for it was backported from 4.20. Rework ESSEDMA patches to compile under 4.19 due to timer changes, Clément Péron did the hard work and his changes were taken from the initial 4.19 PR. MR33 changes had to be manually refreshed to apply. Refresh other patches to apply. Signed-off-by: Robert Marko <robimarko@gmail.com> Remove
2018-12-17 09:39:09 +00:00
+ qcom-ipq4018-nbg6617.dtb \
+ qcom-ipq4018-rt-ac58u.dtb \
+ qcom-ipq4018-wre6606.dtb \
qcom-ipq4019-ap.dk01.1-c1.dtb \
qcom-ipq4019-ap.dk04.1-c1.dtb \
qcom-ipq4019-ap.dk04.1-c3.dtb \
qcom-ipq4019-ap.dk07.1-c1.dtb \
qcom-ipq4019-ap.dk07.1-c2.dtb \
+ qcom-ipq4019-a62.dtb \
ipq40xx: add support for FritzBox 7530 Hardware -------- CPU: Qualcomm IPQ4019 RAM: 256M FLASH: 128M NAND ETH: QCA8075 VDSL: Intel/Lantiq VRX518 PCIe attached currently not supported DECT: Dialog SC14448 currently not supported WiFi2: IPQ4019 2T2R 2SS b/g/n WiFi5: IPQ4019 2T2R 2SS n/ac LED: - Power/DSL green - WLAN green - FON/DECT green - Connect/WPS green - Info green - Info red BTN: - WLAN - FON - WPS/Connect UART: 115200n8 3.3V (located under the Dialog chip) VCC - RX - TX - GND (Square is VCC) Installation ------------ 1. Grab the uboot for the Device from the 'u-boot-fritz7530' subdirectory. Place it in the same directory as the 'eva_ramboot.py' script. It is located in the 'scripts/flashing' subdirectory of the OpenWRT tree. 2. Assign yourself the IP address 192.168.178.10/24. Connect your Computer to one of the boxes LAN ports. 3. Connect Power to the Box. As soon as the LAN port of your computer shows link, load the U-Boot to the box using following command. > ./eva_ramboot.py --offset 0x85000000 192.168.178.1 uboot-fritz7530.bin 4. The U-Boot will now start. Now assign yourself the IP address 192.168.1.70/24. Copy the OpenWRT initramfs (!) image to a TFTP server root directory and rename it to 'FRITZ7530.bin'. 5. The Box will now boot OpenWRT from RAM. This can take up to two minutes. 6. Copy the U-Boot and the OpenWRT sysupgrade (!) image to the Box using scp. SSH into the Box and first write the Bootloader to both previous kernel partitions. > mtd write /path/to/uboot-fritz7530.bin uboot0 > mtd write /path/to/uboot-fritz7530.bin uboot1 7. Remove the AVM filesystem partitions to make room for our kernel + rootfs + overlayfs. > ubirmvol /dev/ubi0 --name=avm_filesys_0 > ubirmvol /dev/ubi0 --name=avm_filesys_1 8. Flash OpenWRT peristently using sysupgrade. > sysupgrade -n /path/to/openwrt-sysupgrade.bin Signed-off-by: David Bauer <mail@david-bauer.net> [removed pcie-dts range node, refreshed on top of AP120-AC/E2600AC] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-02-18 22:58:34 +00:00
+ qcom-ipq4019-fritzbox-7530.dtb \
ipq40xx: add support for AVM FRITZ!Repeater 1200 Hardware -------- SoC: Qualcomm IPQ4019 RAM: 256M DDR3 FLASH: 128M NAND WiFi: 2T2R IPQ4019 bgn 2T2R IPQ4019 a/n/ac ETH: Atheros AR8033 RGMII PHY BTN: 1x Connect (WPS) LED: Power (green/red/yellow) Installation ------------ 1. Grab the uboot for the Device from the 'u-boot-fritz1200' subdirectory. Place it in the same directory as the 'eva_ramboot.py' script. It is located in the 'scripts/flashing' subdirectory of the OpenWRT tree. 2. Assign yourself the IP address 192.168.178.10/24. Connect your Computer to one of the boxes LAN ports. 3. Connect Power to the Box. As soon as the LAN port of your computer shows link, load the U-Boot to the box using following command. > ./eva_ramboot.py --offset 0x85000000 192.168.178.1 uboot-fritz1200.bin 4. The U-Boot will now start. Now assign yourself the IP address 192.168.1.70/24. Copy the OpenWRT initramfs (!) image to a TFTP server root directory and rename it to 'FRITZ1200.bin'. 5. The Box will now boot OpenWRT from RAM. This can take up to two minutes. 6. Copy the U-Boot and the OpenWRT sysupgrade (!) image to the Box using scp. SSH into the Box and first write the Bootloader to both previous kernel partitions. > mtd write /path/to/uboot-fritz1200.bin uboot0 > mtd write /path/to/uboot-fritz1200.bin uboot1 7. Remove the AVM filesystem partitions to make room for our kernel + rootfs + overlayfs. > ubirmvol /dev/ubi0 --name=avm_filesys_0 > ubirmvol /dev/ubi0 --name=avm_filesys_1 8. Flash OpenWRT peristently using sysupgrade. > sysupgrade -n /path/to/openwrt-sysupgrade.bin Signed-off-by: David Bauer <mail@david-bauer.net>
2019-09-10 19:07:23 +00:00
+ qcom-ipq4019-fritzrepeater-1200.dtb \
ipq40xx: add support for AVM FRITZ!Repeater 3000 Hardware -------- CPU: Qualcomm IPQ4019 RAM: 256M (NANYA NT5CC128M16JR-EK) FLASH: 128M NAND (Macronix MX30LF1G18AC-XKI) ETH: Qualcomm QCA8072 WiFi2: IPQ4019 2T2R 2SS b/g/n WiFi5: IPQ4019 2T2R 2SS n/ac WiFi5: QCA9984 4T4R 4SS n/ac LED: - Connect green/blue/red - Power green BTN: WPS/Connect UART: 115200n8 3.3V VCC - RX - TX - GND (Square is VCC) Installation ------------ 1. Grab the uboot for the Device from the 'u-boot-fritz3000' subdirectory. Place it in the same directory as the 'eva_ramboot.py' script. It is located in the 'scripts/flashing' subdirectory of the OpenWRT tree. 2. Assign yourself the IP address 192.168.178.10/24. Connect your Computer to one of the boxes LAN ports. 3. Connect Power to the Box. As soon as the LAN port of your computer shows link, load the U-Boot to the box using following command. > ./eva_ramboot.py --offset 0x85000000 192.168.178.1 uboot-fritz3000.bin 4. The U-Boot will now start. Now assign yourself the IP address 192.168.1.70/24. Copy the OpenWRT initramfs (!) image to a TFTP server root directory and rename it to 'FRITZ3000.bin'. 5. The Box will now boot OpenWRT from RAM. This can take up to two minutes. 6. Copy the U-Boot and the OpenWRT sysupgrade (!) image to the Box using scp. SSH into the Box and first write the Bootloader to both previous kernel partitions. > mtd write /path/to/uboot-fritz3000.bin uboot0 > mtd write /path/to/uboot-fritz3000.bin uboot1 7. Remove the AVM filesystem partitions to make room for our kernel + rootfs + overlayfs. > ubirmvol /dev/ubi0 --name=avm_filesys_0 > ubirmvol /dev/ubi0 --name=avm_filesys_1 8. Flash OpenWRT peristently using sysupgrade. > sysupgrade -n /path/to/openwrt-sysupgrade.bin Signed-off-by: David Bauer <mail@david-bauer.net>
2019-03-11 17:05:32 +00:00
+ qcom-ipq4019-fritzrepeater-3000.dtb \
ipq40xx: build DEVICE_DTS based on SOC and device name This patch uses the SOC variable to calculate DTS names automatically based on the SOC and the device definition node name. This reduces redundancy and (by having to choose DTS name appropriately) will unify the naming of a device in different places (image/Makefile, DTS name, compatible, image name). This is supposed to make life easier for developers and reviewers. Since the kernel uses a "soc-device.dts" scheme for this target, we use this for the derivation of DEVICE_DTS, too, and rename the files not having followed it so far. Note that for some devices the kernel itself is inconsistent, leaving us with a manual overwrite for ap.dk01.1-c1 and ap.dk04.1-c1. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-12-21 00:07:06 +00:00
+ qcom-ipq4019-ea8300.dtb \
ipq40xx: add support for ASUS Lyra SoC: Qualcomm IPQ4019 (Dakota) 717 MHz, 4 cores RAM: 256 MiB (Nanya NT5CC128M16IP-DI) FLASH: 128 MiB (Macronix NAND) WiFi0: Qualcomm IPQ4019 b/g/n 2x2 WiFi1: Qualcomm IPQ4019 a/n/ac 2x2 WiFi2: Qualcomm Atheros QCA9886 a/n/ac BT: Atheros AR3012 IN: WPS Button, Reset Button OUT: RGB-LED via TI LP5523 9-channel Controller UART: Front of Device - 115200 N-8 Pinout 3.3v - RX - TX - GND (Square is VCC) Installation: 1. Transfer OpenWRT-initramfs image to the device via SSH to /tmp. Login credentials are identical to the Web UI. 2. Login to the device via SSH. 3. Flash the initramfs image using > mtd-write -d linux -i openwrt-image-file 4. Power-cycle the device and wait for OpenWRT to boot. 5. From there flash the OpenWRT-sysupgrade image. Ethernet-Ports: Although labeled identically, the port next to the power socket is the LAN port and the other one is WAN. This is the same behavior as in the stock firmware. Signed-off-by: Marius Genheimer <mail@f0wl.cc> [Dropped setup_mac 02_network in favour of 05_set_iface_mac_ipq40xx.sh, reorderd 02_network entries, added board.bin WA for the QCA9886 from ath79, minor dts touchup, added rng to 4.19 dts] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-02-12 16:19:51 +00:00
+ qcom-ipq4019-map-ac2200.dtb \
ipq40xx: build DEVICE_DTS based on SOC and device name This patch uses the SOC variable to calculate DTS names automatically based on the SOC and the device definition node name. This reduces redundancy and (by having to choose DTS name appropriately) will unify the naming of a device in different places (image/Makefile, DTS name, compatible, image name). This is supposed to make life easier for developers and reviewers. Since the kernel uses a "soc-device.dts" scheme for this target, we use this for the derivation of DEVICE_DTS, too, and rename the files not having followed it so far. Note that for some devices the kernel itself is inconsistent, leaving us with a manual overwrite for ap.dk01.1-c1 and ap.dk04.1-c1. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-12-21 00:07:06 +00:00
+ qcom-ipq4019-e2600ac-c1.dtb \
+ qcom-ipq4019-e2600ac-c2.dtb \
+ qcom-ipq4019-u4019-32m.dtb \
ipq40xx: ipq4019: Add new device Compex WPJ419 This device contains 2 flash devices. One NOR (32M) and one NAND (128M). U-boot and caldata are on the NOR, the firmware on the NAND. SoC: IPQ4019 CPU: 4x 710MHz ARMv7 RAM: 256MB FLASH: NOR:32MB NAND:128MB ETH: 2x GMAC Gigabit POE: 802.3 af/at POE, IEEE802.3af/IEEE802.3at(48-56V) WIFI: 1x 2.4Ghz Atheros qca4019 2x2 MU-MIMO 1x 5.0Ghz Atheros qca4019 2x2 MU-MIMO USB: 1x 3.0 PCI: 1x Mini PCIe SIM: 1x Slot SD: 1x MicroSD slot BTN: Reset LED: - Power - Ethernet UART: 1x Serial Port 4 Pin Connector (UART) 1x Serial Port 6 Pin Connector (High Speed UART) POWER: 12V 2A Installation ------------ Initial flashing can only be done via u-boot using the following commands: tftpboot openwrt-ipq40xx-generic-compex_wpj419-squashfs-nand-factory.ubi nand erase.chip; nand write ${fileaddr} 0x0 ${filesize} res Signed-off-by: Daniel Danzberger <daniel@dd-wrt.com>
2019-11-01 11:27:13 +00:00
+ qcom-ipq4019-wpj419.dtb \
ipq40xx: Add patches for 4.19 This adds the necessary patches for 4.19 kernel. Upstreamed patches were dropped, backported upstreamed patches from 4.20. Drop Winbond ID patch since that NAND IC was upstreamed to use SPI-NAND framework and support for it was backported from 4.20. Rework ESSEDMA patches to compile under 4.19 due to timer changes, Clément Péron did the hard work and his changes were taken from the initial 4.19 PR. MR33 changes had to be manually refreshed to apply. Refresh other patches to apply. Signed-off-by: Robert Marko <robimarko@gmail.com> Remove
2018-12-17 09:39:09 +00:00
+ qcom-ipq4028-wpj428.dtb \
ipq40xx: add support for Aruba AP-303 Hardware -------- SoC: Qualcomm IPQ4029 RAM: 512M DDR3 FLASH: - 128MB NAND (Macronix MX30LF1G18AC) - 4MB SPI-NOR (Macronix MX25R3235F) TPM: Atmel AT97SC3203 BLE: Texas Instruments CC2540T attached to ttyMSM0 ETH: Atheros AR8035 LED: WiFi (amber / green) System (red / green) BTN: Reset To connect to the serial console, you can solder to the labled pads next to the USB port or use your Aruba supplied UARt adapter. Do NOT plug a standard USB cable into the Console labled USB-port! Aruba/HPE simply put UART on the micro-USB pins. You can solder yourself an adapter cable: VCC - NC D+ - TX D- - RX GND - GND The console setting in bootloader and OS is 9600 8N1. Voltage level is 3.3V. To enable a full list of commands in the U-Boot "help" command, execute the literal "diag" command. Installation ------------ 1. Get the OpenWrt initramfs image. Rename it to ipq40xx.ari and put it into the TFTP server root directory. Configure the TFTP server to be reachable at 192.168.1.75/24. Connect the machine running the TFTP server to the ethernet port of the access point. 2. Connect to the serial console. Interrupt autobooting by pressing Enter when prompted. 3. Configure the bootargs and bootcmd for OpenWrt. $ setenv bootargs_openwrt "setenv bootargs console=ttyMSM1,9600n8" $ setenv nandboot_openwrt "run bootargs_openwrt; ubi part aos1; ubi read 0x85000000 kernel; bootm 0x85000000" $ setenv ramboot_openwrt "run bootargs_openwrt; setenv ipaddr 192.168.1.105; setenv serverip 192.168.1.75; netget; set fdt_high 0x87000000; bootm" $ setenv bootcmd "run nandboot_openwrt" $ saveenv 4. Load OpenWrt into RAM: $ run ramboot_openwrt 5. After OpenWrt booted, transfer the OpenWrt sysupgrade image to the /tmp folder on the device. 6. Flash OpenWrt: $ ubidetach -p /dev/mtd1 $ ubiformat /dev/mtd1 $ sysupgrade -n /tmp/openwrt-sysupgrade.bin To go back to the stock firmware, simply reset the bootcmd in the bootloader to the original value: $ setenv bootcmd "boot" $ saveenv Signed-off-by: David Bauer <mail@david-bauer.net>
2019-10-23 20:25:14 +00:00
+ qcom-ipq4029-ap-303.dtb \
ipq40xx: Add patches for 4.19 This adds the necessary patches for 4.19 kernel. Upstreamed patches were dropped, backported upstreamed patches from 4.20. Drop Winbond ID patch since that NAND IC was upstreamed to use SPI-NAND framework and support for it was backported from 4.20. Rework ESSEDMA patches to compile under 4.19 due to timer changes, Clément Péron did the hard work and his changes were taken from the initial 4.19 PR. MR33 changes had to be manually refreshed to apply. Refresh other patches to apply. Signed-off-by: Robert Marko <robimarko@gmail.com> Remove
2018-12-17 09:39:09 +00:00
+ qcom-ipq4029-gl-b1300.dtb \
+ qcom-ipq4029-mr33.dtb \
qcom-ipq8064-ap148.dtb \
qcom-msm8660-surf.dtb \
qcom-msm8960-cdp.dtb \
Reference in New Issue Copy Permalink