ExternalVendorCode/openwrt
1
0
Fork 0
mirror of https://github.com/openwrt/openwrt.git synced 2025-02-15 15:12:17 +00:00
Code Issues Actions 2 Packages Projects Releases Wiki Activity
openwrt/target/linux/qualcommax/image/ipq60xx.mk

26 lines
763 B
Makefile
Raw Normal View History

qualcommax: ipq60xx: Add 8devices Mango DVK 8devices Mango DVK is a single board computer / devkit for 8devices Mango system-on-module (SoM). Specifications: * CPU: Qualcomm IPQ6010 Quad core Cortex-A53 1.8GHz * RAM: 512 MB * Storage: * 32 MB serial NOR flash (on SoM) * 256 MB parallel NAND flash (on DVK) * Ethernet: * 2x1G RJ45 ports(QCA8072 or QCA8075) * 1x2.5G RJ45 port (QCA8081) * 1xSFP (shares SGMII with QCA8081) * Switch: Qualcomm Atheros IPQ6010 * WLAN: * 2.4GHz: QCN5121 2x2 802.11b/g/n/ax 574 Mbps PHY rate * 5GHz: QCN5152 2x2 802.11a/n/ac/ax 1201 Mbps PHY rate * USB: * 1x USB3.0 Type-A port * 1x USB2.0 available at mini PCIe slot * PCIe: 1x mini PCIe slot 1xLane Gen3 (8GT/s) * SD/eMMC (on a single shared bus - only one can be active): * micro SD slot * eMMC module connector * LEDs: * Green power led (not controllable) * Green 2.4GHz radio led (GPIO 67) * Green 5GHz radio led (GPIO 66) * Buttons: * 1x (WPS GPIO79) button * GPIOs: 2.54mm header brings out 18 GPIOs (1.8V level) * UART: 4-pin UART header (3.3V level) * 115200 8N1, 3.3V-Tx-Rx-GND (3.3V is pin 1 close to boot-switch SW2) * Power: * PoE IN on 2.5G port (passive 24-48V) * DC power terminal (12-58V) Installation instructions: Vendor image format is compatible with squashfs-sysupgrade image. Run: sysupgrade -n -F openwrt-qualcommax-ipq60xx-8devices_mango-dvk-squashfs-sysupgrade.bin Signed-off-by: Mantas Pucka <mantas@8devices.com>
2024-01-22 11:28:32 +02:00
define Device/8devices_mango-dvk
$(call Device/FitImageLzma)
DEVICE_VENDOR := 8devices
DEVICE_MODEL := Mango-DVK
IMAGE_SIZE := 27776k
BLOCKSIZE := 64k
SOC := ipq6010
SUPPORTED_DEVICES += 8devices,mango
IMAGE/sysupgrade.bin := append-kernel | pad-to 64k | append-rootfs | pad-rootfs | check-size | append-metadata
DEVICE_PACKAGES := ipq-wifi-8devices_mango
endef
TARGET_DEVICES += 8devices_mango-dvk
qualcommax: ipq60xx: add support for netgear wax214 Netgear WAX214 is a 802.11 ax dual-band AP with PoE. (similar to Engenius EWS357APV3) Specifications: • CPU: Qualcomm IPQ6010 Quad core Cortex-A53 • RAM: 512MB of DDR3 • Storage: 128MB NAND (Macronix MX30UF1G18AC) • Ethernet: 1x 1G RJ45 port (QCA8072) PoE • WIFI: 2.4GHz: Qualcomm QCN5022 2x2 802.11b/g/n/ax 574 Mbps PHY rate 5GHz: Qualcomm QCN5052 2x2 802.11a/b/g/n/ac/ax 1201 PHY rate • LEDs: 4 x GPIO-controlled LEDs - 1 Power LED (orange) - 1 LAN LED (blue) - 1 WIFI 5g LED (blue) - 1 WIFI 2g LED (blue) black_small_square Buttons: 1x soft reset black_small_square Power: 12V DC jack or PoE (802.3af ) An populated serial header is onboard, format is 1.25mm 4p (DF13A-4P-1.25H) RX/TX is working, bootwait is active, secure boot is not enabled. The root password of the stock firmware is unknown, but failsafe mode can be entered to reset the password. Installation Instructions: - obtain serial access - stop auto boot (press "4", Entr boot command line interface) - setenv active_fw 0 (to boot from the primary rootfs, or set to 1 to boot from the secondary rootfs partition) - saveenv - tftpboot the initramfs image - bootm - copy openwrt-qualcommax-ipq60xx-netgear_wax214-squashfs-factory.ubi to the device - write the image to the NAND: - cat /proc/mtd and look for rootfs partition (should be mtd11, or mtd12 if you choose active_fw 1) - ubiformat /dev/mtd11 -f -y openwrt-qualcommax-ipq60xx-netgear_wax214-squashfs-factory.ubi - reboot Note: the firmware is senao-based. But I was unable to build a valid senao-header into the image. Maybe they changed the header format and senaoFW isn't working any more. Signed-off-by: Dirk Buchwalder <buchwalder@posteo.de>
2024-03-03 16:00:46 +01:00
define Device/netgear_wax214
$(call Device/FitImage)
$(call Device/UbiFit)
DEVICE_VENDOR := Netgear
DEVICE_MODEL := WAX214
BLOCKSIZE := 128k
PAGESIZE := 2048
DEVICE_DTS_CONFIG := config@cp03-c1
SOC := ipq6010
DEVICE_PACKAGES := ipq-wifi-netgear_wax214
endef
TARGET_DEVICES += netgear_wax214
Reference in New Issue Copy Permalink