2019-12-08 20:44:23 +00:00
|
|
|
CONFIG_BCM_NET_PHYLIB=y
|
2020-02-08 11:58:25 +00:00
|
|
|
CONFIG_BROADCOM_PHY=y
|
ath79: add support for Teltonika RUT955 H7V3C0
This board was previously supported in ar71xx as 'RUT9XX'. The
difference between that and the other RUT955 board already supported in
ath79 is that instead of the SPI shift registers driving the LEDs and
digital outputs that model got an I2C GPIO expander instead.
To support LEDs during early boot and interrupt-driven digital inputs,
I2C support as well as support for PCA953x has to be built-in and
cannot be kernel modules, hence select those symbols for ath79/generic.
Specification:
- 550/400/200 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 4x 10/100 Mbps Ethernet, with passive PoE support on LAN1
- 2T2R 2,4 GHz (AR9344)
- built-in 4G/3G module (example: Quectel EC-25EU)
- internal microSD slot (spi-mmc, buggy and disabled for now)
- RS232 on D-Sub9 port (Cypress ACM via USB, /dev/ttyACM0)
- RS422/RS485 (AR934x high speed UART, /dev/ttyATH1)
- analog 0-24V input (MCP3221)
- various digital inputs and outputs incl. a relay
- 11x LED (4 are driven by AR9344, 7 by PCA9539)
- 2x miniSIM slot (can be swapped via GPIO)
- 2x RP-SMA/F (Wi-Fi), 3x SMA/F (2x WWAN, GPS)
- 1x button (reset)
- DC jack for main power input (9-30 V)
- debugging UART available on PCB edge connector
Serial console (/dev/ttyS0) pinout:
- RX: pin1 (square) on top side of the main PCB (AR9344 is on top)
- TX: pin1 (square) on bottom side
Flash instruction:
Vendor firmware is based on OpenWrt CC release. Use the "factory" image
directly in GUI (make sure to uncheck "keep settings") or in U-Boot web
based recovery. To avoid any problems, make sure to first update vendor
firmware to latest version - "factory" image was successfully tested on
device running "RUT9XX_R_00.06.051" firmware and U-Boot "3.0.1".
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2020-04-29 19:59:04 +00:00
|
|
|
CONFIG_GPIO_PCA953X=y
|
|
|
|
|
CONFIG_GPIO_PCA953X_IRQ=y
|
2018-12-27 01:32:38 +00:00
|
|
|
CONFIG_GPIO_WATCHDOG=y
|
|
|
|
|
CONFIG_GPIO_WATCHDOG_ARCH_INITCALL=y
|
ath79: add support for Teltonika RUT955 H7V3C0
This board was previously supported in ar71xx as 'RUT9XX'. The
difference between that and the other RUT955 board already supported in
ath79 is that instead of the SPI shift registers driving the LEDs and
digital outputs that model got an I2C GPIO expander instead.
To support LEDs during early boot and interrupt-driven digital inputs,
I2C support as well as support for PCA953x has to be built-in and
cannot be kernel modules, hence select those symbols for ath79/generic.
Specification:
- 550/400/200 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 4x 10/100 Mbps Ethernet, with passive PoE support on LAN1
- 2T2R 2,4 GHz (AR9344)
- built-in 4G/3G module (example: Quectel EC-25EU)
- internal microSD slot (spi-mmc, buggy and disabled for now)
- RS232 on D-Sub9 port (Cypress ACM via USB, /dev/ttyACM0)
- RS422/RS485 (AR934x high speed UART, /dev/ttyATH1)
- analog 0-24V input (MCP3221)
- various digital inputs and outputs incl. a relay
- 11x LED (4 are driven by AR9344, 7 by PCA9539)
- 2x miniSIM slot (can be swapped via GPIO)
- 2x RP-SMA/F (Wi-Fi), 3x SMA/F (2x WWAN, GPS)
- 1x button (reset)
- DC jack for main power input (9-30 V)
- debugging UART available on PCB edge connector
Serial console (/dev/ttyS0) pinout:
- RX: pin1 (square) on top side of the main PCB (AR9344 is on top)
- TX: pin1 (square) on bottom side
Flash instruction:
Vendor firmware is based on OpenWrt CC release. Use the "factory" image
directly in GUI (make sure to uncheck "keep settings") or in U-Boot web
based recovery. To avoid any problems, make sure to first update vendor
firmware to latest version - "factory" image was successfully tested on
device running "RUT9XX_R_00.06.051" firmware and U-Boot "3.0.1".
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2020-04-29 19:59:04 +00:00
|
|
|
CONFIG_I2C=y
|
|
|
|
|
CONFIG_I2C_ALGOBIT=y
|
2023-05-30 07:05:06 +00:00
|
|
|
CONFIG_I2C_BOARDINFO=y
|
ath79: add support for Teltonika RUT955 H7V3C0
This board was previously supported in ar71xx as 'RUT9XX'. The
difference between that and the other RUT955 board already supported in
ath79 is that instead of the SPI shift registers driving the LEDs and
digital outputs that model got an I2C GPIO expander instead.
To support LEDs during early boot and interrupt-driven digital inputs,
I2C support as well as support for PCA953x has to be built-in and
cannot be kernel modules, hence select those symbols for ath79/generic.
Specification:
- 550/400/200 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 4x 10/100 Mbps Ethernet, with passive PoE support on LAN1
- 2T2R 2,4 GHz (AR9344)
- built-in 4G/3G module (example: Quectel EC-25EU)
- internal microSD slot (spi-mmc, buggy and disabled for now)
- RS232 on D-Sub9 port (Cypress ACM via USB, /dev/ttyACM0)
- RS422/RS485 (AR934x high speed UART, /dev/ttyATH1)
- analog 0-24V input (MCP3221)
- various digital inputs and outputs incl. a relay
- 11x LED (4 are driven by AR9344, 7 by PCA9539)
- 2x miniSIM slot (can be swapped via GPIO)
- 2x RP-SMA/F (Wi-Fi), 3x SMA/F (2x WWAN, GPS)
- 1x button (reset)
- DC jack for main power input (9-30 V)
- debugging UART available on PCB edge connector
Serial console (/dev/ttyS0) pinout:
- RX: pin1 (square) on top side of the main PCB (AR9344 is on top)
- TX: pin1 (square) on bottom side
Flash instruction:
Vendor firmware is based on OpenWrt CC release. Use the "factory" image
directly in GUI (make sure to uncheck "keep settings") or in U-Boot web
based recovery. To avoid any problems, make sure to first update vendor
firmware to latest version - "factory" image was successfully tested on
device running "RUT9XX_R_00.06.051" firmware and U-Boot "3.0.1".
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2020-04-29 19:59:04 +00:00
|
|
|
CONFIG_I2C_CHARDEV=y
|
|
|
|
|
CONFIG_I2C_GPIO=y
|
2018-03-02 18:28:50 +00:00
|
|
|
CONFIG_INTEL_XWAY_PHY=y
|
2018-06-27 21:55:36 +00:00
|
|
|
CONFIG_IP17XX_PHY=y
|
2018-05-06 08:20:11 +00:00
|
|
|
CONFIG_LEDS_RESET=y
|
2018-06-27 21:55:36 +00:00
|
|
|
CONFIG_MARVELL_PHY=y
|
|
|
|
|
CONFIG_MICREL_PHY=y
|
2019-12-08 20:44:23 +00:00
|
|
|
CONFIG_MTD_REDBOOT_PARTS=y
|
ath79: generic: disable SPI-NOR write protect unconditionally
Kernel 5.15 introduced a significant change to spi-nor subsystem [1],
which would the SPI-NOR core to no longer unprotect the Flash chips if
their protection bits are non-volatile, which is the case for MX25L6405D
and MX25L12805D, used in Ubiquiti XW and WA lines of devices [2].
However, their bootloader forcibly enables this protection before
continuing to boot, making the kernel not unprotect the flash upon boot,
causing JFFS2 to be unable write to the filesystem. Because sysupgrade
seems to unlock the flash explicitly, the upgrade will work, but the
system will be unable to save configrationm showing the following symptom
in the kernel log:
[ 86.168016] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0
[ 86.192344] jffs2_build_filesystem(): unlocking the mtd device...
[ 86.192443] done.
[ 86.200669] jffs2_build_filesystem(): erasing all blocks after the end marker...
[ 86.220646] jffs2: Newly-erased block contained word 0x19852003 at offset 0x001e0000
[ 86.292388] jffs2: Newly-erased block contained word 0x19852003 at offset 0x001d0000
[ 86.324867] jffs2: Newly-erased block contained word 0x19852003 at offset 0x001c0000
[ 86.355316] jffs2: Newly-erased block contained word 0x19852003 at offset 0x001b0000
[ 86.402855] jffs2: Newly-erased block contained word 0x19852003 at offset 0x001a0000
Disable the write protection unconditionally for ath79/generic subtarget,
so the XW and WA devices can function again. However, this is only a
stopgap solution - it probably should be investigated if there is a way
to selectively unlock the area used by rootfs_data - but given the lock
granularity, this seems unlikely.
With this patch in place, rootfs_data partition on my Nanostation Loco
M5 XW is writable again.
Fixes: #12882
Fixes: #13750
Fixes: 579703f38c14 ("ath79: switch to 5.15 as default kernel")
Link: http://www.infradead.org/pipermail/linux-mtd/2020-October/082805.html
Link: https://forum.openwrt.org/t/powerbeam-m5-xw-configuration-loss-after-reboot/141925
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
2023-12-17 17:25:55 +00:00
|
|
|
CONFIG_MTD_SPI_NOR_SWP_DISABLE=y
|
|
|
|
|
# CONFIG_MTD_SPI_NOR_SWP_DISABLE_ON_VOLATILE is not set
|
2023-05-30 08:50:09 +00:00
|
|
|
CONFIG_MTD_SPI_NOR_USE_VARIABLE_ERASE=y
|
2018-03-02 18:28:50 +00:00
|
|
|
CONFIG_MTD_SPLIT_EVA_FW=y
|
2022-10-13 02:20:10 +00:00
|
|
|
CONFIG_NVMEM_SYSFS=y
|
|
|
|
|
CONFIG_NVMEM_U_BOOT_ENV=y
|
2018-05-06 08:20:11 +00:00
|
|
|
CONFIG_PHY_AR7100_USB=y
|
|
|
|
|
CONFIG_PHY_AR7200_USB=y
|
2022-06-21 19:39:39 +00:00
|
|
|
CONFIG_REALTEK_PHY=y
|
2023-05-30 07:05:06 +00:00
|
|
|
CONFIG_REGMAP_I2C=y
|
2018-03-02 18:28:50 +00:00
|
|
|
CONFIG_REGULATOR_FIXED_VOLTAGE=y
|
2019-06-26 19:56:47 +00:00
|
|
|
CONFIG_VITESSE_PHY=y
|
2018-12-27 01:32:38 +00:00
|
|
|
CONFIG_WATCHDOG_CORE=y
|
