openwrt/target/linux/brcm2708/patches-4.19/950-0550-pinctrl-bcm2835-Add-support-for-BCM2838.patch

From 34e6cb1e6f79b24d66353f7c0ac75cd0ae749208 Mon Sep 17 00:00:00 2001
From: Tim Gover <tim.gover@raspberrypi.org>
Date: Wed, 9 Jan 2019 14:43:36 +0000
Subject: [PATCH 550/773] pinctrl-bcm2835: Add support for BCM2838

GPIO configuration on BCM2838 is largely the same as BCM2835 except for
the pull up/down configuration. The old mechanism has been replaced
by new registers which don't require the fixed delay.

Detect BCN2838 at run-time and use the new mechanism. Backwards
compatibility for the device-tree configuration has been retained.
---
 drivers/pinctrl/bcm/pinctrl-bcm2835.c | 58 ++++++++++++++++++++-------
 1 file changed, 44 insertions(+), 14 deletions(-)

--- a/drivers/pinctrl/bcm/pinctrl-bcm2835.c
+++ b/drivers/pinctrl/bcm/pinctrl-bcm2835.c
@@ -67,6 +67,12 @@
 #define GPPUD		0x94	/* Pin Pull-up/down Enable */
 #define GPPUDCLK0	0x98	/* Pin Pull-up/down Enable Clock */
 
+/* 2711 has a different mechanism for pin pull-up/down/enable  */
+#define GPPUPPDN0		0xe4	/* Pin pull-up/down for pins 15:0  */
+#define GPPUPPDN1		0xe8	/* Pin pull-up/down for pins 31:16 */
+#define GPPUPPDN2		0xec	/* Pin pull-up/down for pins 47:32 */
+#define GPPUPPDN3		0xf0	/* Pin pull-up/down for pins 57:48 */
+
 #define FSEL_REG(p)		(GPFSEL0 + (((p) / 10) * 4))
 #define FSEL_SHIFT(p)		(((p) % 10) * 3)
 #define GPIO_REG_OFFSET(p)	((p) / 32)
@@ -917,21 +923,45 @@ static void bcm2835_pull_config_set(stru
 		unsigned int pin, unsigned int arg)
 {
 	u32 off, bit;
+	/* BCM2835, BCM2836 & BCM2837 return 'gpio' for this unused register */
+	int is_2835 = bcm2835_gpio_rd(pc, GPPUPPDN3) == 0x6770696f;
 
-	off = GPIO_REG_OFFSET(pin);
-	bit = GPIO_REG_SHIFT(pin);
-
-	bcm2835_gpio_wr(pc, GPPUD, arg & 3);
-	/*
-	 * BCM2835 datasheet say to wait 150 cycles, but not of what.
-	 * But the VideoCore firmware delay for this operation
-	 * based nearly on the same amount of VPU cycles and this clock
-	 * runs at 250 MHz.
-	 */
-	udelay(1);
-	bcm2835_gpio_wr(pc, GPPUDCLK0 + (off * 4), BIT(bit));
-	udelay(1);
-	bcm2835_gpio_wr(pc, GPPUDCLK0 + (off * 4), 0);
+        if (is_2835) {
+		off = GPIO_REG_OFFSET(pin);
+		bit = GPIO_REG_SHIFT(pin);
+		/*
+		 * BCM2835 datasheet say to wait 150 cycles, but not of what.
+		 * But the VideoCore firmware delay for this operation
+		 * based nearly on the same amount of VPU cycles and this clock
+		 * runs at 250 MHz.
+		 */
+		bcm2835_gpio_wr(pc, GPPUD, arg & 3);
+		udelay(1);
+		bcm2835_gpio_wr(pc, GPPUDCLK0 + (off * 4), BIT(bit));
+		udelay(1);
+		bcm2835_gpio_wr(pc, GPPUDCLK0 + (off * 4), 0);
+	} else {
+		u32 reg;
+		int lsb;
+
+		off = (pin >> 4);
+		if (off > 3)
+			return;
+		lsb = (pin & 0xf) << 1;
+
+		/* The up/down semantics are reversed compared to BCM2835.
+		 * Instead of updating all the device tree files, translate the
+		 * values here.
+		 */
+		if (arg == 2)
+			arg = 1;
+		else if (arg == 1)
+			arg = 2;
+		reg = bcm2835_gpio_rd(pc, GPPUPPDN0 + (off *4));
+		reg &= ~(0x3 << lsb);
+		reg |= (arg & 3) << lsb;
+		bcm2835_gpio_wr(pc, GPPUPPDN0 + (off * 4), reg);
+	}
 }
 
 static int bcm2835_pinconf_set(struct pinctrl_dev *pctldev,