ramips: add support for ELECOM WRC-1167FS
ELECOM WRC-1167FS is a 2.4/5 GHz band 11ac (WiFi-5) router, based on
MT7628AN.
Specification:
- SoC : MediaTek MT7628AN
- RAM : DDR2 64 MiB (NT5TU32M16FG-AC)
- Flash : SPI-NOR 16 MiB (W25Q128JVSIQ)
- WLAN : 2.4/5 GHz 2T2R
- 2.4 GHz : MediaTek MT7628AN (SoC)
- 5 GHz : MediaTek MT7612E
- Ethernet : 10/100 Mbps x2
- Switch : MT7628AN (SoC)
- LEDs/Keys : 6x, 3x (2x buttons, 1x slide-switch)
- UART : through-hole on PCB
- J1: 3.3V, GND, TX, RX from "J1" marking
- 57600n8
- Power : 12 VDC, 1 A
Flash instruction using factory image:
1. Boot WRC-1167FS normally
2. Access to "http://192.168.2.1/" and open firmware update page
("ファームウェア更新")
3. Select the OpenWrt factory image and click apply ("適用") button to
perform firmware update
4. Wait ~120 seconds to complete flashing
Notes:
- Last 0x800000 (8 MiB) in SPI-NOR flash is not used on stock firmware
- Additional padding in factory image is required to avoid incomplete
flashing on stock firmware
MAC addresses:
- LAN : BC:5C:4C:xx:xx:68 (Config, ethaddr (text) / Factory, 0x28 (hex))
- WAN : BC:5C:4C:xx:xx:69 (Config, wanaddr (text) / Factory, 0x22 (hex))
- 2.4GHz: BC:5C:4C:xx:xx:6A (Config, rmac (text) / Factory, 0x4 (hex))
- 5GHz : BC:5C:4C:xx:xx:6B (Config, rmac2 (text) / Factory, 0x8004 (hex))
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2019-09-13 15:14:36 +00:00
|
|
|
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
|
|
|
|
|
|
|
#include "mt7628an.dtsi"
|
|
|
|
|
|
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
|
|
#include <dt-bindings/input/input.h>
|
|
|
|
|
|
|
|
/ {
|
|
|
|
compatible = "elecom,wrc-1167fs", "mediatek,mt7628an-soc";
|
|
|
|
model = "ELECOM WRC-1167FS";
|
|
|
|
|
|
|
|
aliases {
|
|
|
|
led-boot = &led_power;
|
|
|
|
led-failsafe = &led_power;
|
|
|
|
led-running = &led_power;
|
|
|
|
led-upgrade = &led_power;
|
|
|
|
};
|
|
|
|
|
|
|
|
leds {
|
|
|
|
compatible = "gpio-leds";
|
|
|
|
|
|
|
|
led_power: power {
|
|
|
|
label = "green:power";
|
|
|
|
gpios = <&gpio 0 GPIO_ACTIVE_LOW>;
|
|
|
|
};
|
|
|
|
|
|
|
|
wlan5g {
|
|
|
|
label = "green:wlan5g";
|
|
|
|
gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
|
|
|
|
linux,default-trigger = "phy1tpt";
|
|
|
|
};
|
|
|
|
|
|
|
|
wps {
|
|
|
|
label = "red:wps";
|
|
|
|
gpios = <&gpio 37 GPIO_ACTIVE_LOW>;
|
|
|
|
};
|
|
|
|
|
|
|
|
internet {
|
|
|
|
label = "green:internet";
|
|
|
|
gpios = <&gpio 39 GPIO_ACTIVE_LOW>;
|
|
|
|
};
|
|
|
|
|
|
|
|
lan {
|
|
|
|
label = "green:lan";
|
|
|
|
gpios = <&gpio 40 GPIO_ACTIVE_LOW>;
|
|
|
|
};
|
|
|
|
|
|
|
|
wlan2g {
|
|
|
|
label = "green:wlan2g";
|
|
|
|
gpios = <&gpio 44 GPIO_ACTIVE_LOW>;
|
|
|
|
linux,default-trigger = "phy0tpt";
|
|
|
|
};
|
|
|
|
};
|
|
|
|
|
|
|
|
keys {
|
|
|
|
compatible = "gpio-keys";
|
|
|
|
|
|
|
|
ap {
|
|
|
|
label = "ap";
|
|
|
|
gpios = <&gpio 4 GPIO_ACTIVE_LOW>;
|
|
|
|
linux,code = <BTN_0>;
|
|
|
|
linux,input-type = <EV_SW>;
|
|
|
|
};
|
|
|
|
|
|
|
|
reset {
|
|
|
|
label = "reset";
|
|
|
|
gpios = <&gpio 5 GPIO_ACTIVE_LOW>;
|
|
|
|
linux,code = <KEY_RESTART>;
|
|
|
|
};
|
|
|
|
|
|
|
|
wps {
|
|
|
|
label = "wps";
|
|
|
|
gpios = <&gpio 38 GPIO_ACTIVE_LOW>;
|
|
|
|
linux,code = <KEY_WPS_BUTTON>;
|
|
|
|
};
|
|
|
|
};
|
|
|
|
};
|
|
|
|
|
|
|
|
&spi0 {
|
|
|
|
status = "okay";
|
|
|
|
|
|
|
|
flash@0 {
|
|
|
|
compatible = "jedec,spi-nor";
|
|
|
|
reg = <0>;
|
|
|
|
spi-max-frequency = <40000000>;
|
|
|
|
|
|
|
|
partitions {
|
|
|
|
compatible = "fixed-partitions";
|
|
|
|
#address-cells = <1>;
|
|
|
|
#size-cells = <1>;
|
|
|
|
|
|
|
|
partition@0 {
|
|
|
|
label = "u-boot";
|
|
|
|
reg = <0x0 0x30000>;
|
|
|
|
read-only;
|
|
|
|
};
|
|
|
|
|
|
|
|
partition@30000 {
|
|
|
|
label = "u-boot-env";
|
|
|
|
reg = <0x30000 0x10000>;
|
|
|
|
read-only;
|
|
|
|
};
|
|
|
|
|
|
|
|
factory: partition@40000 {
|
|
|
|
label = "factory";
|
|
|
|
reg = <0x40000 0x10000>;
|
|
|
|
read-only;
|
|
|
|
};
|
|
|
|
|
|
|
|
partition@50000 {
|
|
|
|
compatible = "denx,uimage";
|
|
|
|
label = "firmware";
|
|
|
|
reg = <0x50000 0x730000>;
|
|
|
|
};
|
|
|
|
|
|
|
|
partition@780000 {
|
|
|
|
label = "storage";
|
|
|
|
reg = <0x780000 0x80000>;
|
|
|
|
read-only;
|
|
|
|
};
|
|
|
|
};
|
|
|
|
};
|
|
|
|
};
|
|
|
|
|
|
|
|
&ehci {
|
|
|
|
status = "disabled";
|
|
|
|
};
|
|
|
|
|
|
|
|
&esw {
|
|
|
|
mediatek,portmap = <0x2f>;
|
|
|
|
mediatek,portdisable = <0x27>;
|
|
|
|
};
|
|
|
|
|
|
|
|
ðernet {
|
2021-04-02 21:50:02 +00:00
|
|
|
nvmem-cells = <&macaddr_factory_28>;
|
|
|
|
nvmem-cell-names = "mac-address";
|
ramips: add support for ELECOM WRC-1167FS
ELECOM WRC-1167FS is a 2.4/5 GHz band 11ac (WiFi-5) router, based on
MT7628AN.
Specification:
- SoC : MediaTek MT7628AN
- RAM : DDR2 64 MiB (NT5TU32M16FG-AC)
- Flash : SPI-NOR 16 MiB (W25Q128JVSIQ)
- WLAN : 2.4/5 GHz 2T2R
- 2.4 GHz : MediaTek MT7628AN (SoC)
- 5 GHz : MediaTek MT7612E
- Ethernet : 10/100 Mbps x2
- Switch : MT7628AN (SoC)
- LEDs/Keys : 6x, 3x (2x buttons, 1x slide-switch)
- UART : through-hole on PCB
- J1: 3.3V, GND, TX, RX from "J1" marking
- 57600n8
- Power : 12 VDC, 1 A
Flash instruction using factory image:
1. Boot WRC-1167FS normally
2. Access to "http://192.168.2.1/" and open firmware update page
("ファームウェア更新")
3. Select the OpenWrt factory image and click apply ("適用") button to
perform firmware update
4. Wait ~120 seconds to complete flashing
Notes:
- Last 0x800000 (8 MiB) in SPI-NOR flash is not used on stock firmware
- Additional padding in factory image is required to avoid incomplete
flashing on stock firmware
MAC addresses:
- LAN : BC:5C:4C:xx:xx:68 (Config, ethaddr (text) / Factory, 0x28 (hex))
- WAN : BC:5C:4C:xx:xx:69 (Config, wanaddr (text) / Factory, 0x22 (hex))
- 2.4GHz: BC:5C:4C:xx:xx:6A (Config, rmac (text) / Factory, 0x4 (hex))
- 5GHz : BC:5C:4C:xx:xx:6B (Config, rmac2 (text) / Factory, 0x8004 (hex))
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2019-09-13 15:14:36 +00:00
|
|
|
};
|
|
|
|
|
|
|
|
&ohci {
|
|
|
|
status = "disabled";
|
|
|
|
};
|
|
|
|
|
|
|
|
&pcie {
|
|
|
|
status = "okay";
|
|
|
|
};
|
|
|
|
|
|
|
|
&pcie0 {
|
|
|
|
wifi@0,0 {
|
|
|
|
compatible = "mediatek,mt76";
|
|
|
|
reg = <0x0000 0 0 0 0>;
|
|
|
|
mediatek,mtd-eeprom = <&factory 0x8000>;
|
|
|
|
ieee80211-freq-limit = <5000000 6000000>;
|
|
|
|
};
|
|
|
|
};
|
|
|
|
|
|
|
|
&state_default {
|
|
|
|
gpio {
|
|
|
|
groups = "wled_an", "p3led_an", "p4led_an", "wdt", "refclk", "i2c", "i2s";
|
|
|
|
function = "gpio";
|
|
|
|
};
|
|
|
|
};
|
|
|
|
|
|
|
|
&wmac {
|
|
|
|
status = "okay";
|
|
|
|
};
|
2021-04-02 21:50:02 +00:00
|
|
|
|
|
|
|
&factory {
|
|
|
|
compatible = "nvmem-cells";
|
|
|
|
#address-cells = <1>;
|
|
|
|
#size-cells = <1>;
|
|
|
|
|
|
|
|
macaddr_factory_28: macaddr@28 {
|
|
|
|
reg = <0x28 0x6>;
|
|
|
|
};
|
|
|
|
};
|