openwrt/target/linux/ipq806x/patches-5.15/0069-arm-boot-add-dts-files.patch

44 lines
1.3 KiB
Diff
Raw Normal View History

From 8f68331e14dff9a101f2d0e1d6bec84a031f27ee Mon Sep 17 00:00:00 2001
From: John Crispin <john@phrozen.org>
Date: Thu, 9 Mar 2017 11:03:18 +0100
Subject: [PATCH 69/69] arm: boot: add dts files
Signed-off-by: John Crispin <john@phrozen.org>
---
arch/arm/boot/dts/Makefile | 8 ++++++++
1 file changed, 8 insertions(+)
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
kernel: bump 5.15 to 5.15.62 Deleted following upstreamed patches: bcm27xx: 950-0006-drm-vc4-hdmi-Fix-HPD-GPIO-detection.patch bcm27xx: 950-0420-drm-vc4-Adopt-the-dma-configuration-from-the-HVS-or-.patch bcm27xx: 950-0425-drm-vc4-A-present-but-empty-dmas-disables-audio.patch bcm27xx: 950-0432-vc4-drm-Avoid-full-hdmi-audio-fifo-writes.patch bcm27xx: 950-0433-vc4-drm-vc4_plane-Remove-subpixel-positioning-check.patch bcm27xx: 950-0435-drm-vc4-Correct-pixel-order-for-DSI0.patch bcm27xx: 950-0436-drm-vc4-Register-dsi0-as-the-correct-vc4-encoder-typ.patch bcm27xx: 950-0437-drm-vc4-Fix-dsi0-interrupt-support.patch bcm27xx: 950-0438-drm-vc4-Add-correct-stop-condition-to-vc4_dsi_encode.patch bcm27xx: 950-0443-drm-vc4-Fix-timings-for-interlaced-modes.patch bcm27xx: 950-0445-drm-vc4-Fix-margin-calculations-for-the-right-bottom.patch bcm27xx: 950-0475-drm-vc4-Reset-HDMI-MISC_CONTROL-register.patch bcm27xx: 950-0476-drm-vc4-Release-workaround-buffer-and-DMA-in-error-p.patch bcm27xx: 950-0477-drm-vc4-Correct-DSI-divider-calculations.patch bcm27xx: 950-0664-drm-vc4-dsi-Correct-max-divider-to-255-not-7.patch bcm53xx: 072-next-ARM_dts_BCM53015-add-mr26.patch mediatek: 920-linux-next-dts-mt7622-bpi-r64-fix-wps-button.patch Manually rebased following patches: bcm27xx: 950-0004-drm-vc4-hdmi-Remove-the-DDC-probing-for-status-detec.patch bcm27xx: 950-0700-net-phy-lan87xx-Decrease-phy-polling-rate.patch bcm27xx: 950-0711-drm-vc4-Rename-bridge-to-out_bridge.patch bcm27xx: 950-0713-drm-vc4-Remove-splitting-the-bridge-chain-from-the-d.patch bcm27xx: 950-0715-drm-vc4-Convert-vc4_dsi-to-using-a-bridge-instead-of.patch bcm27xx: 950-0787-vc4-drm-vc4_plane-Keep-fractional-source-coords-insi.patch bcm27xx: 950-0914-mmc-block-Don-t-do-single-sector-reads-during-recove.patch Runtime tested on turris-omnia and glinet-b1300. Tested-by: John Audia <therealgraysky@proton.me> [bcm2711/RPi4B, mt7622/RT3200] Signed-off-by: Petr Štetiar <ynezz@true.cz>
2022-08-22 12:02:36 +00:00
@@ -957,8 +957,30 @@ dtb-$(CONFIG_ARCH_QCOM) += \
qcom-ipq4019-ap.dk04.1-c3.dtb \
qcom-ipq4019-ap.dk07.1-c1.dtb \
qcom-ipq4019-ap.dk07.1-c2.dtb \
+ qcom-ipq8062-wg2600hp3.dtb \
qcom-ipq8064-ap148.dtb \
qcom-ipq8064-rb3011.dtb \
+ qcom-ipq8064-c2600.dtb \
+ qcom-ipq8064-d7800.dtb \
+ qcom-ipq8064-db149.dtb \
+ qcom-ipq8064-ap161.dtb \
+ qcom-ipq8064-ea7500-v1.dtb \
+ qcom-ipq8064-ea8500.dtb \
+ qcom-ipq8064-g10.dtb \
+ qcom-ipq8064-r7500.dtb \
+ qcom-ipq8064-r7500v2.dtb \
+ qcom-ipq8064-unifi-ac-hd.dtb \
+ qcom-ipq8064-wg2600hp.dtb \
+ qcom-ipq8064-wpq864.dtb \
+ qcom-ipq8064-wxr-2533dhp.dtb \
+ qcom-ipq8065-nbg6817.dtb \
+ qcom-ipq8065-r7800.dtb \
+ qcom-ipq8065-rt4230w-rev6.dtb \
ipq806x: add support for Arris TR4400 v2 / RAC2V1A Hardware specs: SoC: Qualcomm IPQ8065 (dual core Cortex-A15) RAM: 512 MB DDR3 Flash: 256 MB NAND, 32 MB NOR WiFi: QCA9983 2.4 GHz, QCA9984 5 GHz Switch: QCA8337 Ethernet: 5x 10/100/1000 Mbit/s USB: 1x USB 3.0 Type-A Buttons: WPS, Reset Power: 12 VDC, 2.5 A Ethernet ports: 1x WAN: connected to eth2 4x LAN: connected via the switch to eth0 and eth1 (eth0 is disabled in OEM firmware) MAC addresses (OEM and OpenWrt): fw_env @ 0x00 d4:ab:82:??:??:?a LAN (eth1) fw_env @ 0x06 d4:ab:82:??:??:?b WAN (eth2) fw_env @ 0x0c d4:ab:82:??:??:?c WLAN 2.4 GHz (ath1) fw_env @ 0x12 d4:ab:82:??:??:?d WLAN 5 GHz (ath0) fw_env @ 0x18 d4:ab:82:??:??:?e OEM usage unknown (eth0 in OpenWrt) OID d4:ab:82 is registered to: ARRIS Group, Inc., 6450 Sequence Drive, San Diego CA 92121, US More info: https://openwrt.org/inbox/toh/arris/tr4400_v2 IMPORTANT: This port requires moving the 'fw_env' partition prior to first boot to consolidate 70% of the usable space in flash into a contiguous partition. 'fw_env' contains factory-programmed MAC addresses, SSIDs, and passwords. Its contents must be copied to 'rootfs_1' prior to booting via initramfs. Note that the stock 'fw_env' partition will be wiped during sysupgrade. A writable 'stock_fw_env' partition pointing to the old, stock location is included in the port to help rolling back this change if desired. Installation: - Requires serial access and a TFTP server. - Fully boot stock, press ENTER, type in: mtd erase /dev/mtd21 dd if=/dev/mtd22 bs=128K count=1 | mtd write - /dev/mtd21 umount /config && ubidetach -m 23 && mtd erase /dev/mtd23 - Reboot and interrupt U-Boot by pressing a key, type in: set mtdids 'nand0=nand0' set mtdparts 'mtdparts=nand0:155M@0x6500000(mtd_ubi)' set bootcmd 'ubi part mtd_ubi && ubi read 0x44000000 kernel && bootm' env save - Setup TFTP server serving initramfs image as 'recovery.bin', type in: set ipaddr 192.168.1.1 set serverip 192.168.1.2 tftpboot recovery.bin && bootm - Use sysupgrade to install squashfs image. This port is based on work done by AmadeusGhost <amadeus@jmu.edu.cn>. Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com> [add 5.15 changes for 0069-arm-boot-add-dts-files.patch] Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2022-04-07 06:18:59 +00:00
+ qcom-ipq8065-tr4400-v2.dtb \
+ qcom-ipq8065-xr500.dtb \
+ qcom-ipq8068-ecw5410.dtb \
+ qcom-ipq8068-mr42.dtb \
+ qcom-ipq8068-mr52.dtb \
qcom-msm8226-samsung-s3ve3g.dtb \
qcom-msm8660-surf.dtb \
qcom-msm8960-cdp.dtb \