ramips: add support for TP-Link RE650 v2
TP-Link RE650 v2 is largely similar to v1 that
is already supported by OpenWrt. Notable differences
is differnt SPI Flash - 8 MB instead of 16 MB
(from cFeon instead of Winbond) and a different
configuration of PCIE connections to wifi chips.
Otherwise it's largely the same product as v1
Hardware specification:
- SoC 880 MHz - MediaTek MT7621AT
- 128 MB of DDR3 RAM
- 8 MB - cFeon QH64A-104HIP
- 4T4R 2.4 GHz - MediaTek MT7615E
- 4T4R 5 GHz - MediaTek MT7615E
- 1x 1 Gbps Ethernet - MT7621AT integrated
- 7x LEDs (Power, 2G, 5G, WPS(x2), Lan(x2))
- 4x buttons (Reset, Power, WPS, LED)
- UART pinout - GND, RX, TX, labeled in the middle of the PCB,
requires soldering because they're not through holes.
Serial console @ 57600,8n1
Flash instructions:
Upload
openwrt-ramips-mt7621-tplink_re650-v2-squashfs-factory.bin
from the RE650 web interface.
TFTP recovery to stock firmware:
I didn't try recovering back to the stock firmware, however,
if there is such process for other RExxx devices, it seems like
it could be similar here.
Signed-off-by: Marcin Gordziejewski <openwrt@flicksfix.com>
2022-04-07 22:29:20 +00:00
|
|
|
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
|
|
|
|
|
|
|
#include "mt7621.dtsi"
|
|
|
|
|
|
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
|
|
#include <dt-bindings/input/input.h>
|
2024-02-07 13:48:43 +00:00
|
|
|
#include <dt-bindings/leds/common.h>
|
ramips: add support for TP-Link RE650 v2
TP-Link RE650 v2 is largely similar to v1 that
is already supported by OpenWrt. Notable differences
is differnt SPI Flash - 8 MB instead of 16 MB
(from cFeon instead of Winbond) and a different
configuration of PCIE connections to wifi chips.
Otherwise it's largely the same product as v1
Hardware specification:
- SoC 880 MHz - MediaTek MT7621AT
- 128 MB of DDR3 RAM
- 8 MB - cFeon QH64A-104HIP
- 4T4R 2.4 GHz - MediaTek MT7615E
- 4T4R 5 GHz - MediaTek MT7615E
- 1x 1 Gbps Ethernet - MT7621AT integrated
- 7x LEDs (Power, 2G, 5G, WPS(x2), Lan(x2))
- 4x buttons (Reset, Power, WPS, LED)
- UART pinout - GND, RX, TX, labeled in the middle of the PCB,
requires soldering because they're not through holes.
Serial console @ 57600,8n1
Flash instructions:
Upload
openwrt-ramips-mt7621-tplink_re650-v2-squashfs-factory.bin
from the RE650 web interface.
TFTP recovery to stock firmware:
I didn't try recovering back to the stock firmware, however,
if there is such process for other RExxx devices, it seems like
it could be similar here.
Signed-off-by: Marcin Gordziejewski <openwrt@flicksfix.com>
2022-04-07 22:29:20 +00:00
|
|
|
|
|
|
|
/ {
|
|
|
|
compatible = "tplink,re650-v2", "mediatek,mt7621-soc";
|
|
|
|
model = "TP-Link RE650 v2";
|
|
|
|
|
|
|
|
aliases {
|
|
|
|
label-mac-device = &gmac0;
|
|
|
|
led-boot = &led_power;
|
|
|
|
led-failsafe = &led_power;
|
|
|
|
led-running = &led_power;
|
|
|
|
led-upgrade = &led_power;
|
|
|
|
};
|
|
|
|
|
|
|
|
keys {
|
|
|
|
compatible = "gpio-keys";
|
|
|
|
|
|
|
|
wps {
|
|
|
|
label = "wps";
|
|
|
|
gpios = <&gpio 18 GPIO_ACTIVE_LOW>;
|
|
|
|
debounce-interval = <60>;
|
|
|
|
linux,code = <KEY_WPS_BUTTON>;
|
|
|
|
};
|
|
|
|
|
|
|
|
power {
|
|
|
|
label = "power";
|
|
|
|
gpios = <&gpio 25 GPIO_ACTIVE_LOW>;
|
|
|
|
debounce-interval = <60>;
|
|
|
|
linux,code = <KEY_POWER>;
|
|
|
|
};
|
|
|
|
|
|
|
|
led {
|
|
|
|
label = "led";
|
|
|
|
gpios = <&gpio 30 GPIO_ACTIVE_LOW>;
|
|
|
|
debounce-interval = <60>;
|
|
|
|
linux,code = <KEY_LIGHTS_TOGGLE>;
|
|
|
|
};
|
|
|
|
|
|
|
|
reset {
|
|
|
|
label = "reset";
|
|
|
|
gpios = <&gpio 31 GPIO_ACTIVE_LOW>;
|
|
|
|
debounce-interval = <60>;
|
|
|
|
linux,code = <KEY_RESTART>;
|
|
|
|
};
|
|
|
|
};
|
|
|
|
|
|
|
|
leds {
|
|
|
|
compatible = "gpio-leds";
|
|
|
|
|
|
|
|
led_power: power {
|
2024-02-07 13:48:43 +00:00
|
|
|
function = LED_FUNCTION_POWER;
|
|
|
|
color = <LED_COLOR_ID_BLUE>;
|
ramips: add support for TP-Link RE650 v2
TP-Link RE650 v2 is largely similar to v1 that
is already supported by OpenWrt. Notable differences
is differnt SPI Flash - 8 MB instead of 16 MB
(from cFeon instead of Winbond) and a different
configuration of PCIE connections to wifi chips.
Otherwise it's largely the same product as v1
Hardware specification:
- SoC 880 MHz - MediaTek MT7621AT
- 128 MB of DDR3 RAM
- 8 MB - cFeon QH64A-104HIP
- 4T4R 2.4 GHz - MediaTek MT7615E
- 4T4R 5 GHz - MediaTek MT7615E
- 1x 1 Gbps Ethernet - MT7621AT integrated
- 7x LEDs (Power, 2G, 5G, WPS(x2), Lan(x2))
- 4x buttons (Reset, Power, WPS, LED)
- UART pinout - GND, RX, TX, labeled in the middle of the PCB,
requires soldering because they're not through holes.
Serial console @ 57600,8n1
Flash instructions:
Upload
openwrt-ramips-mt7621-tplink_re650-v2-squashfs-factory.bin
from the RE650 web interface.
TFTP recovery to stock firmware:
I didn't try recovering back to the stock firmware, however,
if there is such process for other RExxx devices, it seems like
it could be similar here.
Signed-off-by: Marcin Gordziejewski <openwrt@flicksfix.com>
2022-04-07 22:29:20 +00:00
|
|
|
gpios = <&gpio 22 GPIO_ACTIVE_LOW>;
|
|
|
|
};
|
|
|
|
|
|
|
|
wifi2g {
|
|
|
|
label = "blue:wifi2g";
|
|
|
|
gpios = <&gpio 23 GPIO_ACTIVE_LOW>;
|
|
|
|
linux,default-trigger = "phy0tpt";
|
|
|
|
};
|
|
|
|
|
|
|
|
wifi5g {
|
|
|
|
label = "blue:wifi5g";
|
|
|
|
gpios = <&gpio 24 GPIO_ACTIVE_LOW>;
|
|
|
|
linux,default-trigger = "phy1tpt";
|
|
|
|
};
|
|
|
|
|
|
|
|
wps_red {
|
2024-02-07 13:48:43 +00:00
|
|
|
function = LED_FUNCTION_WPS;
|
|
|
|
color = <LED_COLOR_ID_RED>;
|
ramips: add support for TP-Link RE650 v2
TP-Link RE650 v2 is largely similar to v1 that
is already supported by OpenWrt. Notable differences
is differnt SPI Flash - 8 MB instead of 16 MB
(from cFeon instead of Winbond) and a different
configuration of PCIE connections to wifi chips.
Otherwise it's largely the same product as v1
Hardware specification:
- SoC 880 MHz - MediaTek MT7621AT
- 128 MB of DDR3 RAM
- 8 MB - cFeon QH64A-104HIP
- 4T4R 2.4 GHz - MediaTek MT7615E
- 4T4R 5 GHz - MediaTek MT7615E
- 1x 1 Gbps Ethernet - MT7621AT integrated
- 7x LEDs (Power, 2G, 5G, WPS(x2), Lan(x2))
- 4x buttons (Reset, Power, WPS, LED)
- UART pinout - GND, RX, TX, labeled in the middle of the PCB,
requires soldering because they're not through holes.
Serial console @ 57600,8n1
Flash instructions:
Upload
openwrt-ramips-mt7621-tplink_re650-v2-squashfs-factory.bin
from the RE650 web interface.
TFTP recovery to stock firmware:
I didn't try recovering back to the stock firmware, however,
if there is such process for other RExxx devices, it seems like
it could be similar here.
Signed-off-by: Marcin Gordziejewski <openwrt@flicksfix.com>
2022-04-07 22:29:20 +00:00
|
|
|
gpios = <&gpio 26 GPIO_ACTIVE_HIGH>;
|
|
|
|
};
|
|
|
|
|
|
|
|
wps_blue {
|
2024-02-07 13:48:43 +00:00
|
|
|
function = LED_FUNCTION_WPS;
|
|
|
|
color = <LED_COLOR_ID_BLUE>;
|
ramips: add support for TP-Link RE650 v2
TP-Link RE650 v2 is largely similar to v1 that
is already supported by OpenWrt. Notable differences
is differnt SPI Flash - 8 MB instead of 16 MB
(from cFeon instead of Winbond) and a different
configuration of PCIE connections to wifi chips.
Otherwise it's largely the same product as v1
Hardware specification:
- SoC 880 MHz - MediaTek MT7621AT
- 128 MB of DDR3 RAM
- 8 MB - cFeon QH64A-104HIP
- 4T4R 2.4 GHz - MediaTek MT7615E
- 4T4R 5 GHz - MediaTek MT7615E
- 1x 1 Gbps Ethernet - MT7621AT integrated
- 7x LEDs (Power, 2G, 5G, WPS(x2), Lan(x2))
- 4x buttons (Reset, Power, WPS, LED)
- UART pinout - GND, RX, TX, labeled in the middle of the PCB,
requires soldering because they're not through holes.
Serial console @ 57600,8n1
Flash instructions:
Upload
openwrt-ramips-mt7621-tplink_re650-v2-squashfs-factory.bin
from the RE650 web interface.
TFTP recovery to stock firmware:
I didn't try recovering back to the stock firmware, however,
if there is such process for other RExxx devices, it seems like
it could be similar here.
Signed-off-by: Marcin Gordziejewski <openwrt@flicksfix.com>
2022-04-07 22:29:20 +00:00
|
|
|
gpios = <&gpio 27 GPIO_ACTIVE_HIGH>;
|
|
|
|
};
|
|
|
|
|
|
|
|
eth_act {
|
|
|
|
label = "green:eth_act";
|
|
|
|
gpios = <&gpio 28 GPIO_ACTIVE_LOW>;
|
|
|
|
};
|
|
|
|
|
|
|
|
eth_link {
|
|
|
|
label = "green:eth_link";
|
|
|
|
gpios = <&gpio 29 GPIO_ACTIVE_LOW>;
|
|
|
|
};
|
|
|
|
};
|
|
|
|
};
|
|
|
|
|
|
|
|
&spi0 {
|
|
|
|
status = "okay";
|
|
|
|
|
|
|
|
flash@0 {
|
|
|
|
compatible = "jedec,spi-nor";
|
|
|
|
reg = <0>;
|
|
|
|
spi-max-frequency = <40000000>;
|
|
|
|
|
|
|
|
partitions {
|
|
|
|
compatible = "fixed-partitions";
|
|
|
|
#address-cells = <1>;
|
|
|
|
#size-cells = <1>;
|
|
|
|
|
|
|
|
partition@0 {
|
|
|
|
label = "u-boot";
|
|
|
|
reg = <0x0 0x20000>;
|
|
|
|
read-only;
|
|
|
|
};
|
|
|
|
|
|
|
|
partition@20000 {
|
|
|
|
compatible = "tplink,firmware";
|
|
|
|
label = "firmware";
|
|
|
|
reg = <0x20000 0x7a0000>;
|
|
|
|
};
|
|
|
|
|
|
|
|
config: partition@7c0000 {
|
|
|
|
label = "config";
|
|
|
|
reg = <0x7c0000 0x2d440>;
|
|
|
|
read-only;
|
2023-10-02 02:12:02 +00:00
|
|
|
|
2023-11-07 23:55:58 +00:00
|
|
|
nvmem-layout {
|
|
|
|
compatible = "fixed-layout";
|
|
|
|
#address-cells = <1>;
|
|
|
|
#size-cells = <1>;
|
|
|
|
|
|
|
|
macaddr_config_10008: macaddr@10008 {
|
2023-11-08 03:39:00 +00:00
|
|
|
compatible = "mac-base";
|
2023-11-07 23:55:58 +00:00
|
|
|
reg = <0x10008 0x6>;
|
2023-11-08 03:39:00 +00:00
|
|
|
#nvmem-cell-cells = <1>;
|
2023-11-07 23:55:58 +00:00
|
|
|
};
|
2023-10-02 02:12:02 +00:00
|
|
|
};
|
ramips: add support for TP-Link RE650 v2
TP-Link RE650 v2 is largely similar to v1 that
is already supported by OpenWrt. Notable differences
is differnt SPI Flash - 8 MB instead of 16 MB
(from cFeon instead of Winbond) and a different
configuration of PCIE connections to wifi chips.
Otherwise it's largely the same product as v1
Hardware specification:
- SoC 880 MHz - MediaTek MT7621AT
- 128 MB of DDR3 RAM
- 8 MB - cFeon QH64A-104HIP
- 4T4R 2.4 GHz - MediaTek MT7615E
- 4T4R 5 GHz - MediaTek MT7615E
- 1x 1 Gbps Ethernet - MT7621AT integrated
- 7x LEDs (Power, 2G, 5G, WPS(x2), Lan(x2))
- 4x buttons (Reset, Power, WPS, LED)
- UART pinout - GND, RX, TX, labeled in the middle of the PCB,
requires soldering because they're not through holes.
Serial console @ 57600,8n1
Flash instructions:
Upload
openwrt-ramips-mt7621-tplink_re650-v2-squashfs-factory.bin
from the RE650 web interface.
TFTP recovery to stock firmware:
I didn't try recovering back to the stock firmware, however,
if there is such process for other RExxx devices, it seems like
it could be similar here.
Signed-off-by: Marcin Gordziejewski <openwrt@flicksfix.com>
2022-04-07 22:29:20 +00:00
|
|
|
};
|
|
|
|
|
|
|
|
radio: partition@7f0000 {
|
|
|
|
label = "radio";
|
|
|
|
reg = <0x7f0000 0x10000>;
|
|
|
|
read-only;
|
2023-10-02 02:12:02 +00:00
|
|
|
|
2023-11-07 23:55:58 +00:00
|
|
|
nvmem-layout {
|
|
|
|
compatible = "fixed-layout";
|
|
|
|
#address-cells = <1>;
|
|
|
|
#size-cells = <1>;
|
|
|
|
|
|
|
|
eeprom_radio_0: eeprom@0 {
|
|
|
|
reg = <0x0 0x4da8>;
|
|
|
|
};
|
2023-10-02 02:12:02 +00:00
|
|
|
|
2023-11-07 23:55:58 +00:00
|
|
|
eeprom_radio_8000: eeprom@8000 {
|
|
|
|
reg = <0x8000 0x4da8>;
|
|
|
|
};
|
2023-10-02 02:12:02 +00:00
|
|
|
};
|
ramips: add support for TP-Link RE650 v2
TP-Link RE650 v2 is largely similar to v1 that
is already supported by OpenWrt. Notable differences
is differnt SPI Flash - 8 MB instead of 16 MB
(from cFeon instead of Winbond) and a different
configuration of PCIE connections to wifi chips.
Otherwise it's largely the same product as v1
Hardware specification:
- SoC 880 MHz - MediaTek MT7621AT
- 128 MB of DDR3 RAM
- 8 MB - cFeon QH64A-104HIP
- 4T4R 2.4 GHz - MediaTek MT7615E
- 4T4R 5 GHz - MediaTek MT7615E
- 1x 1 Gbps Ethernet - MT7621AT integrated
- 7x LEDs (Power, 2G, 5G, WPS(x2), Lan(x2))
- 4x buttons (Reset, Power, WPS, LED)
- UART pinout - GND, RX, TX, labeled in the middle of the PCB,
requires soldering because they're not through holes.
Serial console @ 57600,8n1
Flash instructions:
Upload
openwrt-ramips-mt7621-tplink_re650-v2-squashfs-factory.bin
from the RE650 web interface.
TFTP recovery to stock firmware:
I didn't try recovering back to the stock firmware, however,
if there is such process for other RExxx devices, it seems like
it could be similar here.
Signed-off-by: Marcin Gordziejewski <openwrt@flicksfix.com>
2022-04-07 22:29:20 +00:00
|
|
|
};
|
|
|
|
};
|
|
|
|
};
|
|
|
|
};
|
|
|
|
|
|
|
|
&state_default {
|
|
|
|
gpio {
|
|
|
|
groups = "rgmii2", "wdt";
|
|
|
|
function = "gpio";
|
|
|
|
};
|
|
|
|
};
|
|
|
|
|
|
|
|
&pcie {
|
|
|
|
status = "okay";
|
|
|
|
};
|
|
|
|
|
|
|
|
&pcie1 {
|
|
|
|
wifi@0,0 {
|
|
|
|
compatible = "mediatek,mt76";
|
|
|
|
reg = <0x0000 0 0 0 0>;
|
2023-11-08 03:39:00 +00:00
|
|
|
nvmem-cells = <&eeprom_radio_0>, <&macaddr_config_10008 1>;
|
2023-10-02 02:12:02 +00:00
|
|
|
nvmem-cell-names = "eeprom", "mac-address";
|
ramips: add support for TP-Link RE650 v2
TP-Link RE650 v2 is largely similar to v1 that
is already supported by OpenWrt. Notable differences
is differnt SPI Flash - 8 MB instead of 16 MB
(from cFeon instead of Winbond) and a different
configuration of PCIE connections to wifi chips.
Otherwise it's largely the same product as v1
Hardware specification:
- SoC 880 MHz - MediaTek MT7621AT
- 128 MB of DDR3 RAM
- 8 MB - cFeon QH64A-104HIP
- 4T4R 2.4 GHz - MediaTek MT7615E
- 4T4R 5 GHz - MediaTek MT7615E
- 1x 1 Gbps Ethernet - MT7621AT integrated
- 7x LEDs (Power, 2G, 5G, WPS(x2), Lan(x2))
- 4x buttons (Reset, Power, WPS, LED)
- UART pinout - GND, RX, TX, labeled in the middle of the PCB,
requires soldering because they're not through holes.
Serial console @ 57600,8n1
Flash instructions:
Upload
openwrt-ramips-mt7621-tplink_re650-v2-squashfs-factory.bin
from the RE650 web interface.
TFTP recovery to stock firmware:
I didn't try recovering back to the stock firmware, however,
if there is such process for other RExxx devices, it seems like
it could be similar here.
Signed-off-by: Marcin Gordziejewski <openwrt@flicksfix.com>
2022-04-07 22:29:20 +00:00
|
|
|
ieee80211-freq-limit = <2400000 2500000>;
|
|
|
|
};
|
|
|
|
};
|
|
|
|
|
|
|
|
&pcie0 {
|
|
|
|
wifi@0,0 {
|
|
|
|
compatible = "mediatek,mt76";
|
|
|
|
reg = <0x0000 0 0 0 0>;
|
2023-11-08 03:39:00 +00:00
|
|
|
nvmem-cells = <&eeprom_radio_8000>, <&macaddr_config_10008 2>;
|
2023-10-02 02:12:02 +00:00
|
|
|
nvmem-cell-names = "eeprom", "mac-address";
|
ramips: add support for TP-Link RE650 v2
TP-Link RE650 v2 is largely similar to v1 that
is already supported by OpenWrt. Notable differences
is differnt SPI Flash - 8 MB instead of 16 MB
(from cFeon instead of Winbond) and a different
configuration of PCIE connections to wifi chips.
Otherwise it's largely the same product as v1
Hardware specification:
- SoC 880 MHz - MediaTek MT7621AT
- 128 MB of DDR3 RAM
- 8 MB - cFeon QH64A-104HIP
- 4T4R 2.4 GHz - MediaTek MT7615E
- 4T4R 5 GHz - MediaTek MT7615E
- 1x 1 Gbps Ethernet - MT7621AT integrated
- 7x LEDs (Power, 2G, 5G, WPS(x2), Lan(x2))
- 4x buttons (Reset, Power, WPS, LED)
- UART pinout - GND, RX, TX, labeled in the middle of the PCB,
requires soldering because they're not through holes.
Serial console @ 57600,8n1
Flash instructions:
Upload
openwrt-ramips-mt7621-tplink_re650-v2-squashfs-factory.bin
from the RE650 web interface.
TFTP recovery to stock firmware:
I didn't try recovering back to the stock firmware, however,
if there is such process for other RExxx devices, it seems like
it could be similar here.
Signed-off-by: Marcin Gordziejewski <openwrt@flicksfix.com>
2022-04-07 22:29:20 +00:00
|
|
|
ieee80211-freq-limit = <5000000 6000000>;
|
|
|
|
};
|
|
|
|
};
|
|
|
|
|
|
|
|
ðernet {
|
|
|
|
pinctrl-0 = <&mdio_pins>, <&rgmii1_pins>;
|
|
|
|
};
|
|
|
|
|
|
|
|
&gmac0 {
|
2023-11-08 03:39:00 +00:00
|
|
|
nvmem-cells = <&macaddr_config_10008 0>;
|
ramips: add support for TP-Link RE650 v2
TP-Link RE650 v2 is largely similar to v1 that
is already supported by OpenWrt. Notable differences
is differnt SPI Flash - 8 MB instead of 16 MB
(from cFeon instead of Winbond) and a different
configuration of PCIE connections to wifi chips.
Otherwise it's largely the same product as v1
Hardware specification:
- SoC 880 MHz - MediaTek MT7621AT
- 128 MB of DDR3 RAM
- 8 MB - cFeon QH64A-104HIP
- 4T4R 2.4 GHz - MediaTek MT7615E
- 4T4R 5 GHz - MediaTek MT7615E
- 1x 1 Gbps Ethernet - MT7621AT integrated
- 7x LEDs (Power, 2G, 5G, WPS(x2), Lan(x2))
- 4x buttons (Reset, Power, WPS, LED)
- UART pinout - GND, RX, TX, labeled in the middle of the PCB,
requires soldering because they're not through holes.
Serial console @ 57600,8n1
Flash instructions:
Upload
openwrt-ramips-mt7621-tplink_re650-v2-squashfs-factory.bin
from the RE650 web interface.
TFTP recovery to stock firmware:
I didn't try recovering back to the stock firmware, however,
if there is such process for other RExxx devices, it seems like
it could be similar here.
Signed-off-by: Marcin Gordziejewski <openwrt@flicksfix.com>
2022-04-07 22:29:20 +00:00
|
|
|
nvmem-cell-names = "mac-address";
|
|
|
|
};
|
|
|
|
|
|
|
|
&switch0 {
|
|
|
|
ports {
|
|
|
|
port@0 {
|
|
|
|
status = "okay";
|
|
|
|
label = "lan";
|
|
|
|
};
|
|
|
|
};
|
|
|
|
};
|