openwrt/target/linux/ipq40xx/patches-4.19/700-net-add-qualcomm-mdio.patch

289 lines
7.7 KiB
Diff
Raw Normal View History

ipq40xx: Add support for Unielec U4019 This commit adds support for the 32MB storage/512MB RAM version of the U4019 IPQ4019-based board from Unielec. The board has the following specifications: * Qualcomm IPQ4019 (running at 717MHz) * 512MB DDR3 RAM (optional 256MB/1GB) * 32MB SPI NOR (optional 8/16MB or NAND) * Five gigabit ports (Qualcomm QCA8075) * 1x 2.4 GHz wifi (QCA4019 hw1.0) * 1x 5 Ghz wifi (QCA4019 hw1.0) * 1x mini-PCIe slot (only USB-pins connected) * 1x SIM slot (mini-SIM) * 1x USB2.0 port * 1x button * 1x controllable LED * 1x micro SD-card reader Working: * Ethernet * Wifi * USB-port * mini-PCIe slot + SIM slot * Button * Sysupgrade Not working: * SD card slot (no upstream support) Installation instructions: In order to install OpenWRT on the U4019, you need to go via the initramfs-image. The installation steps are as follows: * Connect to board via serial (header exposed and clearly marked). * Interrupt bootloader by pressing a button. * Copy the initramfs-image to your tftp folder, call the file C0A80079.img. * Give the network interface connected to the U4019 the address 192.168.0.156/24. * Start your tftp-server and run tftpboot on the board. * Run bootm when the file has been transferred, to boot OpenWRT. * Once OpenWRT has booted, copy the sysupgrade-image to the device and run sysupgrade to install OpenWRT on the U4019. Notes: - Since IPQ4019 has been moved to 4.19, I have not added support for kernel 4.14. - There is a bug with hardware encryption on IPQ4019, causing poor performance with TCP and ipsec (see for example FS#2355). In order to improve performance, I have disabled hardware encryption in the DTS. We can enable hw. enc. once/if bug is fixed. - In order for Ethernet to work, the phy has to be reset by setting gpio 47 low/high. Adding support for phy reset via gpio required patching the mdio-driver, and the code added comes from the vendor driver. I do not know if patching the driver is an acceptable approach or not. v1->v2: * Do not use wildcard as identifier in the board.d-scripts (thanks Adrian Schmutzler). Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
2019-10-20 09:33:13 +00:00
From 234d6f40fb4b771b396b45a9492aab463771bd0b Mon Sep 17 00:00:00 2001
From: Kristian Evensen <kristian.evensen@gmail.com>
Date: Tue, 6 Aug 2019 11:42:57 +0200
Subject: [PATCH] phy: Add ipq40xx mdio driver
---
drivers/net/phy/Kconfig | 7 +
drivers/net/phy/Makefile | 1 +
drivers/net/phy/mdio-ipq40xx.c | 247 +++++++++++++++++++++++++++++++++
3 files changed, 255 insertions(+)
create mode 100644 drivers/net/phy/mdio-ipq40xx.c
--- a/drivers/net/phy/Kconfig
+++ b/drivers/net/phy/Kconfig
@@ -519,6 +519,13 @@ config XILINX_GMII2RGMII
the Reduced Gigabit Media Independent Interface(RGMII) between
Ethernet physical media devices and the Gigabit Ethernet controller.
+config MDIO_IPQ40XX
+ tristate "Qualcomm Atheros ipq40xx MDIO interface"
+ depends on HAS_IOMEM && OF
+ ---help---
+ This driver supports the MDIO interface found in Qualcomm
+ Atheros ipq40xx Soc chip.
+
endif # PHYLIB
config MICREL_KS8995MA
--- a/drivers/net/phy/Makefile
+++ b/drivers/net/phy/Makefile
@@ -48,6 +48,7 @@ obj-$(CONFIG_MDIO_CAVIUM) += mdio-cavium
obj-$(CONFIG_MDIO_GPIO) += mdio-gpio.o
obj-$(CONFIG_MDIO_HISI_FEMAC) += mdio-hisi-femac.o
obj-$(CONFIG_MDIO_I2C) += mdio-i2c.o
+obj-$(CONFIG_MDIO_IPQ40XX) += mdio-ipq40xx.o
obj-$(CONFIG_MDIO_MOXART) += mdio-moxart.o
obj-$(CONFIG_MDIO_MSCC_MIIM) += mdio-mscc-miim.o
obj-$(CONFIG_MDIO_OCTEON) += mdio-octeon.o
--- /dev/null
+++ b/drivers/net/phy/mdio-ipq40xx.c
ipq40xx: Add support for Unielec U4019 This commit adds support for the 32MB storage/512MB RAM version of the U4019 IPQ4019-based board from Unielec. The board has the following specifications: * Qualcomm IPQ4019 (running at 717MHz) * 512MB DDR3 RAM (optional 256MB/1GB) * 32MB SPI NOR (optional 8/16MB or NAND) * Five gigabit ports (Qualcomm QCA8075) * 1x 2.4 GHz wifi (QCA4019 hw1.0) * 1x 5 Ghz wifi (QCA4019 hw1.0) * 1x mini-PCIe slot (only USB-pins connected) * 1x SIM slot (mini-SIM) * 1x USB2.0 port * 1x button * 1x controllable LED * 1x micro SD-card reader Working: * Ethernet * Wifi * USB-port * mini-PCIe slot + SIM slot * Button * Sysupgrade Not working: * SD card slot (no upstream support) Installation instructions: In order to install OpenWRT on the U4019, you need to go via the initramfs-image. The installation steps are as follows: * Connect to board via serial (header exposed and clearly marked). * Interrupt bootloader by pressing a button. * Copy the initramfs-image to your tftp folder, call the file C0A80079.img. * Give the network interface connected to the U4019 the address 192.168.0.156/24. * Start your tftp-server and run tftpboot on the board. * Run bootm when the file has been transferred, to boot OpenWRT. * Once OpenWRT has booted, copy the sysupgrade-image to the device and run sysupgrade to install OpenWRT on the U4019. Notes: - Since IPQ4019 has been moved to 4.19, I have not added support for kernel 4.14. - There is a bug with hardware encryption on IPQ4019, causing poor performance with TCP and ipsec (see for example FS#2355). In order to improve performance, I have disabled hardware encryption in the DTS. We can enable hw. enc. once/if bug is fixed. - In order for Ethernet to work, the phy has to be reset by setting gpio 47 low/high. Adding support for phy reset via gpio required patching the mdio-driver, and the code added comes from the vendor driver. I do not know if patching the driver is an acceptable approach or not. v1->v2: * Do not use wildcard as identifier in the board.d-scripts (thanks Adrian Schmutzler). Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
2019-10-20 09:33:13 +00:00
@@ -0,0 +1,247 @@
+/*
+ * Copyright (c) 2015-2016, The Linux Foundation. All rights reserved.
+ *
+ * Permission to use, copy, modify, and/or distribute this software for
+ * any purpose with or without fee is hereby granted, provided that the
+ * above copyright notice and this permission notice appear in all copies.
+ * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
+ * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
+ * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
+ * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
+ * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
+ * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT
+ * OF OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
+ */
+
+#include <linux/delay.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/mutex.h>
+#include <linux/io.h>
+#include <linux/of_address.h>
+#include <linux/of_mdio.h>
ipq40xx: Add support for Unielec U4019 This commit adds support for the 32MB storage/512MB RAM version of the U4019 IPQ4019-based board from Unielec. The board has the following specifications: * Qualcomm IPQ4019 (running at 717MHz) * 512MB DDR3 RAM (optional 256MB/1GB) * 32MB SPI NOR (optional 8/16MB or NAND) * Five gigabit ports (Qualcomm QCA8075) * 1x 2.4 GHz wifi (QCA4019 hw1.0) * 1x 5 Ghz wifi (QCA4019 hw1.0) * 1x mini-PCIe slot (only USB-pins connected) * 1x SIM slot (mini-SIM) * 1x USB2.0 port * 1x button * 1x controllable LED * 1x micro SD-card reader Working: * Ethernet * Wifi * USB-port * mini-PCIe slot + SIM slot * Button * Sysupgrade Not working: * SD card slot (no upstream support) Installation instructions: In order to install OpenWRT on the U4019, you need to go via the initramfs-image. The installation steps are as follows: * Connect to board via serial (header exposed and clearly marked). * Interrupt bootloader by pressing a button. * Copy the initramfs-image to your tftp folder, call the file C0A80079.img. * Give the network interface connected to the U4019 the address 192.168.0.156/24. * Start your tftp-server and run tftpboot on the board. * Run bootm when the file has been transferred, to boot OpenWRT. * Once OpenWRT has booted, copy the sysupgrade-image to the device and run sysupgrade to install OpenWRT on the U4019. Notes: - Since IPQ4019 has been moved to 4.19, I have not added support for kernel 4.14. - There is a bug with hardware encryption on IPQ4019, causing poor performance with TCP and ipsec (see for example FS#2355). In order to improve performance, I have disabled hardware encryption in the DTS. We can enable hw. enc. once/if bug is fixed. - In order for Ethernet to work, the phy has to be reset by setting gpio 47 low/high. Adding support for phy reset via gpio required patching the mdio-driver, and the code added comes from the vendor driver. I do not know if patching the driver is an acceptable approach or not. v1->v2: * Do not use wildcard as identifier in the board.d-scripts (thanks Adrian Schmutzler). Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
2019-10-20 09:33:13 +00:00
+#include <linux/of_gpio.h>
+#include <linux/phy.h>
+#include <linux/platform_device.h>
ipq40xx: Add support for Unielec U4019 This commit adds support for the 32MB storage/512MB RAM version of the U4019 IPQ4019-based board from Unielec. The board has the following specifications: * Qualcomm IPQ4019 (running at 717MHz) * 512MB DDR3 RAM (optional 256MB/1GB) * 32MB SPI NOR (optional 8/16MB or NAND) * Five gigabit ports (Qualcomm QCA8075) * 1x 2.4 GHz wifi (QCA4019 hw1.0) * 1x 5 Ghz wifi (QCA4019 hw1.0) * 1x mini-PCIe slot (only USB-pins connected) * 1x SIM slot (mini-SIM) * 1x USB2.0 port * 1x button * 1x controllable LED * 1x micro SD-card reader Working: * Ethernet * Wifi * USB-port * mini-PCIe slot + SIM slot * Button * Sysupgrade Not working: * SD card slot (no upstream support) Installation instructions: In order to install OpenWRT on the U4019, you need to go via the initramfs-image. The installation steps are as follows: * Connect to board via serial (header exposed and clearly marked). * Interrupt bootloader by pressing a button. * Copy the initramfs-image to your tftp folder, call the file C0A80079.img. * Give the network interface connected to the U4019 the address 192.168.0.156/24. * Start your tftp-server and run tftpboot on the board. * Run bootm when the file has been transferred, to boot OpenWRT. * Once OpenWRT has booted, copy the sysupgrade-image to the device and run sysupgrade to install OpenWRT on the U4019. Notes: - Since IPQ4019 has been moved to 4.19, I have not added support for kernel 4.14. - There is a bug with hardware encryption on IPQ4019, causing poor performance with TCP and ipsec (see for example FS#2355). In order to improve performance, I have disabled hardware encryption in the DTS. We can enable hw. enc. once/if bug is fixed. - In order for Ethernet to work, the phy has to be reset by setting gpio 47 low/high. Adding support for phy reset via gpio required patching the mdio-driver, and the code added comes from the vendor driver. I do not know if patching the driver is an acceptable approach or not. v1->v2: * Do not use wildcard as identifier in the board.d-scripts (thanks Adrian Schmutzler). Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
2019-10-20 09:33:13 +00:00
+#include <linux/gpio.h>
+
+#define MDIO_CTRL_0_REG 0x40
+#define MDIO_CTRL_1_REG 0x44
+#define MDIO_CTRL_2_REG 0x48
+#define MDIO_CTRL_3_REG 0x4c
+#define MDIO_CTRL_4_REG 0x50
+#define MDIO_CTRL_4_ACCESS_BUSY BIT(16)
+#define MDIO_CTRL_4_ACCESS_START BIT(8)
+#define MDIO_CTRL_4_ACCESS_CODE_READ 0
+#define MDIO_CTRL_4_ACCESS_CODE_WRITE 1
+#define CTRL_0_REG_DEFAULT_VALUE 0x150FF
+
+#define IPQ40XX_MDIO_RETRY 1000
+#define IPQ40XX_MDIO_DELAY 10
+
+struct ipq40xx_mdio_data {
+ struct mii_bus *mii_bus;
+ void __iomem *membase;
+ struct device *dev;
+};
+
+static int ipq40xx_mdio_wait_busy(struct ipq40xx_mdio_data *am)
+{
+ int i;
+
+ for (i = 0; i < IPQ40XX_MDIO_RETRY; i++) {
+ unsigned int busy;
+
+ busy = readl(am->membase + MDIO_CTRL_4_REG) &
+ MDIO_CTRL_4_ACCESS_BUSY;
+ if (!busy)
+ return 0;
+
+ /* BUSY might take to be cleard by 15~20 times of loop */
+ udelay(IPQ40XX_MDIO_DELAY);
+ }
+
+ dev_err(am->dev, "%s: MDIO operation timed out\n", am->mii_bus->name);
+
+ return -ETIMEDOUT;
+}
+
+static int ipq40xx_mdio_read(struct mii_bus *bus, int mii_id, int regnum)
+{
+ struct ipq40xx_mdio_data *am = bus->priv;
+ int value = 0;
+ unsigned int cmd = 0;
+
+ lockdep_assert_held(&bus->mdio_lock);
+
+ if (ipq40xx_mdio_wait_busy(am))
+ return -ETIMEDOUT;
+
+ /* issue the phy address and reg */
+ writel((mii_id << 8) | regnum, am->membase + MDIO_CTRL_1_REG);
+
+ cmd = MDIO_CTRL_4_ACCESS_START|MDIO_CTRL_4_ACCESS_CODE_READ;
+
+ /* issue read command */
+ writel(cmd, am->membase + MDIO_CTRL_4_REG);
+
+ /* Wait read complete */
+ if (ipq40xx_mdio_wait_busy(am))
+ return -ETIMEDOUT;
+
+ /* Read data */
+ value = readl(am->membase + MDIO_CTRL_3_REG);
+
+ return value;
+}
+
+static int ipq40xx_mdio_write(struct mii_bus *bus, int mii_id, int regnum,
+ u16 value)
+{
+ struct ipq40xx_mdio_data *am = bus->priv;
+ unsigned int cmd = 0;
+
+ lockdep_assert_held(&bus->mdio_lock);
+
+ if (ipq40xx_mdio_wait_busy(am))
+ return -ETIMEDOUT;
+
+ /* issue the phy address and reg */
+ writel((mii_id << 8) | regnum, am->membase + MDIO_CTRL_1_REG);
+
+ /* issue write data */
+ writel(value, am->membase + MDIO_CTRL_2_REG);
+
+ cmd = MDIO_CTRL_4_ACCESS_START|MDIO_CTRL_4_ACCESS_CODE_WRITE;
+ /* issue write command */
+ writel(cmd, am->membase + MDIO_CTRL_4_REG);
+
+ /* Wait write complete */
+ if (ipq40xx_mdio_wait_busy(am))
+ return -ETIMEDOUT;
+
+ return 0;
+}
+
ipq40xx: Add support for Unielec U4019 This commit adds support for the 32MB storage/512MB RAM version of the U4019 IPQ4019-based board from Unielec. The board has the following specifications: * Qualcomm IPQ4019 (running at 717MHz) * 512MB DDR3 RAM (optional 256MB/1GB) * 32MB SPI NOR (optional 8/16MB or NAND) * Five gigabit ports (Qualcomm QCA8075) * 1x 2.4 GHz wifi (QCA4019 hw1.0) * 1x 5 Ghz wifi (QCA4019 hw1.0) * 1x mini-PCIe slot (only USB-pins connected) * 1x SIM slot (mini-SIM) * 1x USB2.0 port * 1x button * 1x controllable LED * 1x micro SD-card reader Working: * Ethernet * Wifi * USB-port * mini-PCIe slot + SIM slot * Button * Sysupgrade Not working: * SD card slot (no upstream support) Installation instructions: In order to install OpenWRT on the U4019, you need to go via the initramfs-image. The installation steps are as follows: * Connect to board via serial (header exposed and clearly marked). * Interrupt bootloader by pressing a button. * Copy the initramfs-image to your tftp folder, call the file C0A80079.img. * Give the network interface connected to the U4019 the address 192.168.0.156/24. * Start your tftp-server and run tftpboot on the board. * Run bootm when the file has been transferred, to boot OpenWRT. * Once OpenWRT has booted, copy the sysupgrade-image to the device and run sysupgrade to install OpenWRT on the U4019. Notes: - Since IPQ4019 has been moved to 4.19, I have not added support for kernel 4.14. - There is a bug with hardware encryption on IPQ4019, causing poor performance with TCP and ipsec (see for example FS#2355). In order to improve performance, I have disabled hardware encryption in the DTS. We can enable hw. enc. once/if bug is fixed. - In order for Ethernet to work, the phy has to be reset by setting gpio 47 low/high. Adding support for phy reset via gpio required patching the mdio-driver, and the code added comes from the vendor driver. I do not know if patching the driver is an acceptable approach or not. v1->v2: * Do not use wildcard as identifier in the board.d-scripts (thanks Adrian Schmutzler). Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
2019-10-20 09:33:13 +00:00
+static int ipq40xx_phy_reset(struct platform_device *pdev)
+{
+ struct device_node *mdio_node;
+ int phy_reset_gpio_number;
+ int ret;
+
+ mdio_node = of_find_node_by_name(NULL, "mdio");
+ if (!mdio_node) {
+ dev_err(&pdev->dev, "Could not find mdio node\n");
+ return 0;
ipq40xx: Add support for Unielec U4019 This commit adds support for the 32MB storage/512MB RAM version of the U4019 IPQ4019-based board from Unielec. The board has the following specifications: * Qualcomm IPQ4019 (running at 717MHz) * 512MB DDR3 RAM (optional 256MB/1GB) * 32MB SPI NOR (optional 8/16MB or NAND) * Five gigabit ports (Qualcomm QCA8075) * 1x 2.4 GHz wifi (QCA4019 hw1.0) * 1x 5 Ghz wifi (QCA4019 hw1.0) * 1x mini-PCIe slot (only USB-pins connected) * 1x SIM slot (mini-SIM) * 1x USB2.0 port * 1x button * 1x controllable LED * 1x micro SD-card reader Working: * Ethernet * Wifi * USB-port * mini-PCIe slot + SIM slot * Button * Sysupgrade Not working: * SD card slot (no upstream support) Installation instructions: In order to install OpenWRT on the U4019, you need to go via the initramfs-image. The installation steps are as follows: * Connect to board via serial (header exposed and clearly marked). * Interrupt bootloader by pressing a button. * Copy the initramfs-image to your tftp folder, call the file C0A80079.img. * Give the network interface connected to the U4019 the address 192.168.0.156/24. * Start your tftp-server and run tftpboot on the board. * Run bootm when the file has been transferred, to boot OpenWRT. * Once OpenWRT has booted, copy the sysupgrade-image to the device and run sysupgrade to install OpenWRT on the U4019. Notes: - Since IPQ4019 has been moved to 4.19, I have not added support for kernel 4.14. - There is a bug with hardware encryption on IPQ4019, causing poor performance with TCP and ipsec (see for example FS#2355). In order to improve performance, I have disabled hardware encryption in the DTS. We can enable hw. enc. once/if bug is fixed. - In order for Ethernet to work, the phy has to be reset by setting gpio 47 low/high. Adding support for phy reset via gpio required patching the mdio-driver, and the code added comes from the vendor driver. I do not know if patching the driver is an acceptable approach or not. v1->v2: * Do not use wildcard as identifier in the board.d-scripts (thanks Adrian Schmutzler). Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
2019-10-20 09:33:13 +00:00
+ }
+
+ ret = of_get_named_gpio(mdio_node, "phy-reset-gpio", 0);
+ if (ret < 0) {
+ dev_err(&pdev->dev, "Could not find phy-reset-gpio\n");
+ return 0;
ipq40xx: Add support for Unielec U4019 This commit adds support for the 32MB storage/512MB RAM version of the U4019 IPQ4019-based board from Unielec. The board has the following specifications: * Qualcomm IPQ4019 (running at 717MHz) * 512MB DDR3 RAM (optional 256MB/1GB) * 32MB SPI NOR (optional 8/16MB or NAND) * Five gigabit ports (Qualcomm QCA8075) * 1x 2.4 GHz wifi (QCA4019 hw1.0) * 1x 5 Ghz wifi (QCA4019 hw1.0) * 1x mini-PCIe slot (only USB-pins connected) * 1x SIM slot (mini-SIM) * 1x USB2.0 port * 1x button * 1x controllable LED * 1x micro SD-card reader Working: * Ethernet * Wifi * USB-port * mini-PCIe slot + SIM slot * Button * Sysupgrade Not working: * SD card slot (no upstream support) Installation instructions: In order to install OpenWRT on the U4019, you need to go via the initramfs-image. The installation steps are as follows: * Connect to board via serial (header exposed and clearly marked). * Interrupt bootloader by pressing a button. * Copy the initramfs-image to your tftp folder, call the file C0A80079.img. * Give the network interface connected to the U4019 the address 192.168.0.156/24. * Start your tftp-server and run tftpboot on the board. * Run bootm when the file has been transferred, to boot OpenWRT. * Once OpenWRT has booted, copy the sysupgrade-image to the device and run sysupgrade to install OpenWRT on the U4019. Notes: - Since IPQ4019 has been moved to 4.19, I have not added support for kernel 4.14. - There is a bug with hardware encryption on IPQ4019, causing poor performance with TCP and ipsec (see for example FS#2355). In order to improve performance, I have disabled hardware encryption in the DTS. We can enable hw. enc. once/if bug is fixed. - In order for Ethernet to work, the phy has to be reset by setting gpio 47 low/high. Adding support for phy reset via gpio required patching the mdio-driver, and the code added comes from the vendor driver. I do not know if patching the driver is an acceptable approach or not. v1->v2: * Do not use wildcard as identifier in the board.d-scripts (thanks Adrian Schmutzler). Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
2019-10-20 09:33:13 +00:00
+ }
+
+ phy_reset_gpio_number = ret;
+
+ ret = gpio_request(phy_reset_gpio_number, "phy-reset-gpio");
+ if (ret) {
+ dev_err(&pdev->dev, "Can't get phy-reset-gpio %d\n", ret);
+ return ret;
+ }
+
+ ret = gpio_direction_output(phy_reset_gpio_number, 0x0);
+ if (ret) {
+ dev_err(&pdev->dev,
+ "Can't set direction for phy-reset-gpio %d\n", ret);
+ goto phy_reset_out;
+ }
+
+ usleep_range(1000, 10005);
+
+ gpio_set_value(phy_reset_gpio_number, 0x01);
+
+phy_reset_out:
+ gpio_free(phy_reset_gpio_number);
+
+ return ret;
+}
+
+static int ipq40xx_mdio_probe(struct platform_device *pdev)
+{
+ struct ipq40xx_mdio_data *am;
+ struct resource *res;
ipq40xx: Add support for Unielec U4019 This commit adds support for the 32MB storage/512MB RAM version of the U4019 IPQ4019-based board from Unielec. The board has the following specifications: * Qualcomm IPQ4019 (running at 717MHz) * 512MB DDR3 RAM (optional 256MB/1GB) * 32MB SPI NOR (optional 8/16MB or NAND) * Five gigabit ports (Qualcomm QCA8075) * 1x 2.4 GHz wifi (QCA4019 hw1.0) * 1x 5 Ghz wifi (QCA4019 hw1.0) * 1x mini-PCIe slot (only USB-pins connected) * 1x SIM slot (mini-SIM) * 1x USB2.0 port * 1x button * 1x controllable LED * 1x micro SD-card reader Working: * Ethernet * Wifi * USB-port * mini-PCIe slot + SIM slot * Button * Sysupgrade Not working: * SD card slot (no upstream support) Installation instructions: In order to install OpenWRT on the U4019, you need to go via the initramfs-image. The installation steps are as follows: * Connect to board via serial (header exposed and clearly marked). * Interrupt bootloader by pressing a button. * Copy the initramfs-image to your tftp folder, call the file C0A80079.img. * Give the network interface connected to the U4019 the address 192.168.0.156/24. * Start your tftp-server and run tftpboot on the board. * Run bootm when the file has been transferred, to boot OpenWRT. * Once OpenWRT has booted, copy the sysupgrade-image to the device and run sysupgrade to install OpenWRT on the U4019. Notes: - Since IPQ4019 has been moved to 4.19, I have not added support for kernel 4.14. - There is a bug with hardware encryption on IPQ4019, causing poor performance with TCP and ipsec (see for example FS#2355). In order to improve performance, I have disabled hardware encryption in the DTS. We can enable hw. enc. once/if bug is fixed. - In order for Ethernet to work, the phy has to be reset by setting gpio 47 low/high. Adding support for phy reset via gpio required patching the mdio-driver, and the code added comes from the vendor driver. I do not know if patching the driver is an acceptable approach or not. v1->v2: * Do not use wildcard as identifier in the board.d-scripts (thanks Adrian Schmutzler). Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
2019-10-20 09:33:13 +00:00
+ int i, ret;
+
+ ret = ipq40xx_phy_reset(pdev);
+ if (ret) {
+ dev_err(&pdev->dev, "Could not find qca8075 reset gpio\n");
+ return -ENODEV;
+ }
+
+ am = devm_kzalloc(&pdev->dev, sizeof(*am), GFP_KERNEL);
+ if (!am)
+ return -ENOMEM;
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ if (!res) {
+ dev_err(&pdev->dev, "no iomem resource found\n");
+ return -ENXIO;
+ }
+
+ am->membase = devm_ioremap_resource(&pdev->dev, res);
+ if (IS_ERR(am->membase)) {
+ dev_err(&pdev->dev, "unable to ioremap registers\n");
+ return PTR_ERR(am->membase);
+ }
+
+ am->mii_bus = devm_mdiobus_alloc(&pdev->dev);
+ if (!am->mii_bus)
+ return -ENOMEM;
+
+ writel(CTRL_0_REG_DEFAULT_VALUE, am->membase + MDIO_CTRL_0_REG);
+
+ am->mii_bus->name = "ipq40xx_mdio";
+ am->mii_bus->read = ipq40xx_mdio_read;
+ am->mii_bus->write = ipq40xx_mdio_write;
+ am->mii_bus->priv = am;
+ am->mii_bus->parent = &pdev->dev;
+ snprintf(am->mii_bus->id, MII_BUS_ID_SIZE, "%s", dev_name(&pdev->dev));
+
+ am->dev = &pdev->dev;
+ platform_set_drvdata(pdev, am);
+
+ return of_mdiobus_register(am->mii_bus, pdev->dev.of_node);
+}
+
+static int ipq40xx_mdio_remove(struct platform_device *pdev)
+{
+ struct ipq40xx_mdio_data *am = platform_get_drvdata(pdev);
+
+ mdiobus_unregister(am->mii_bus);
+
+ return 0;
+}
+
+static const struct of_device_id ipq40xx_mdio_dt_ids[] = {
+ { .compatible = "qcom,ipq4019-mdio" },
+ { }
+};
+MODULE_DEVICE_TABLE(of, ipq40xx_mdio_dt_ids);
+
+static struct platform_driver ipq40xx_mdio_driver = {
+ .probe = ipq40xx_mdio_probe,
+ .remove = ipq40xx_mdio_remove,
+ .driver = {
+ .name = "ipq40xx-mdio",
+ .of_match_table = ipq40xx_mdio_dt_ids,
+ },
+};
+
+module_platform_driver(ipq40xx_mdio_driver);
+
+#define DRV_VERSION "1.0"
+
+MODULE_DESCRIPTION("IPQ40XX MDIO interface driver");
+MODULE_AUTHOR("Qualcomm Atheros");
+MODULE_VERSION(DRV_VERSION);
+MODULE_LICENSE("Dual BSD/GPL");