ramips: add support for D-Link DIR-882 R1
Specifications:
- SoC: MediaTek MT7621AT
- RAM: 128 MB (DDR3)
- Flash: 16 MB (SPI NOR)
- WiFi: MediaTek MT7615N (x2)
- Switch: 1 WAN, 4 LAN (Gigabit)
- Ports: 1 USB 2.0, 1 USB 3.0
- Buttons: Reset, WiFi Toggle, WPS
- LEDs: Power, Internet, WiFi 2.4G WiFi 5G, USB 2.0, USB 3.0
The R1 revision is identical to the A1 revision except
- No Config2 Parition, therefore
- factory partition resized to 64k from 128K
- Firmware partition offset is 0x50000 not 0x60000
- Firmware partitions size increased by 64K
- Firmware partition type is "denx,uimage", not "sge,uimage"
- Padding of image creation "uimage-padhdr 96" removed
Installation:
- Older firmware versions: put the factory image on a USB stick, turn on
the telnet console, and flash using the following cmd
"fw_updater Linux /mnt/usb_X_X/firmware.bin"
- D-Link FailsafeUI:
Power down the router, press and hold the reset button, then
re-plug it. Keep the reset button pressed until the internet LED stops
flashing, then jack into any lan port and manually assign a static IP
address in 192.168.0.0/24 other than 192.168.0.0 (e.g. 192.168.0.2)
and go to http://192.168.0.1
Flash with the factory image.
Signed-off-by: Andrew Pikler <andrew.pikler@gmail.com>
2020-10-05 14:16:44 +00:00
|
|
|
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
|
|
|
|
|
|
|
&spi0 {
|
|
|
|
status = "okay";
|
|
|
|
|
|
|
|
flash@0 {
|
|
|
|
compatible = "jedec,spi-nor";
|
|
|
|
reg = <0>;
|
|
|
|
spi-max-frequency = <50000000>;
|
|
|
|
|
|
|
|
partitions {
|
|
|
|
compatible = "fixed-partitions";
|
|
|
|
#address-cells = <1>;
|
|
|
|
#size-cells = <1>;
|
|
|
|
|
|
|
|
partition@0 {
|
|
|
|
label = "u-boot";
|
|
|
|
reg = <0x0 0x30000>;
|
|
|
|
read-only;
|
|
|
|
};
|
|
|
|
|
|
|
|
partition@30000 {
|
|
|
|
label = "u-boot-env";
|
|
|
|
reg = <0x30000 0x10000>;
|
|
|
|
read-only;
|
|
|
|
};
|
|
|
|
|
2024-02-17 14:10:10 +00:00
|
|
|
partition@40000 {
|
ramips: add support for D-Link DIR-882 R1
Specifications:
- SoC: MediaTek MT7621AT
- RAM: 128 MB (DDR3)
- Flash: 16 MB (SPI NOR)
- WiFi: MediaTek MT7615N (x2)
- Switch: 1 WAN, 4 LAN (Gigabit)
- Ports: 1 USB 2.0, 1 USB 3.0
- Buttons: Reset, WiFi Toggle, WPS
- LEDs: Power, Internet, WiFi 2.4G WiFi 5G, USB 2.0, USB 3.0
The R1 revision is identical to the A1 revision except
- No Config2 Parition, therefore
- factory partition resized to 64k from 128K
- Firmware partition offset is 0x50000 not 0x60000
- Firmware partitions size increased by 64K
- Firmware partition type is "denx,uimage", not "sge,uimage"
- Padding of image creation "uimage-padhdr 96" removed
Installation:
- Older firmware versions: put the factory image on a USB stick, turn on
the telnet console, and flash using the following cmd
"fw_updater Linux /mnt/usb_X_X/firmware.bin"
- D-Link FailsafeUI:
Power down the router, press and hold the reset button, then
re-plug it. Keep the reset button pressed until the internet LED stops
flashing, then jack into any lan port and manually assign a static IP
address in 192.168.0.0/24 other than 192.168.0.0 (e.g. 192.168.0.2)
and go to http://192.168.0.1
Flash with the factory image.
Signed-off-by: Andrew Pikler <andrew.pikler@gmail.com>
2020-10-05 14:16:44 +00:00
|
|
|
label = "factory";
|
|
|
|
reg = <0x40000 0x10000>;
|
|
|
|
read-only;
|
2023-10-02 02:12:02 +00:00
|
|
|
|
2023-11-07 23:55:58 +00:00
|
|
|
nvmem-layout {
|
|
|
|
compatible = "fixed-layout";
|
|
|
|
#address-cells = <1>;
|
|
|
|
#size-cells = <1>;
|
2023-10-02 02:12:02 +00:00
|
|
|
|
2023-11-07 23:55:58 +00:00
|
|
|
eeprom_factory_0: eeprom@0 {
|
|
|
|
reg = <0x0 0x4da8>;
|
|
|
|
};
|
2023-10-02 02:12:02 +00:00
|
|
|
|
2023-11-07 23:55:58 +00:00
|
|
|
eeprom_factory_8000: eeprom@8000 {
|
|
|
|
reg = <0x8000 0x4da8>;
|
|
|
|
};
|
2023-10-02 02:12:02 +00:00
|
|
|
|
2023-11-07 23:55:58 +00:00
|
|
|
macaddr_factory_4: macaddr@4 {
|
2023-11-08 03:39:00 +00:00
|
|
|
compatible = "mac-base";
|
2023-11-07 23:55:58 +00:00
|
|
|
reg = <0x4 0x6>;
|
2023-11-08 03:39:00 +00:00
|
|
|
#nvmem-cell-cells = <1>;
|
2023-11-07 23:55:58 +00:00
|
|
|
};
|
|
|
|
|
|
|
|
macaddr_factory_e000: macaddr@e000 {
|
2024-02-15 05:31:12 +00:00
|
|
|
compatible = "mac-base";
|
2023-11-07 23:55:58 +00:00
|
|
|
reg = <0xe000 0x6>;
|
2024-02-15 05:31:12 +00:00
|
|
|
#nvmem-cell-cells = <1>;
|
2023-11-07 23:55:58 +00:00
|
|
|
};
|
2023-10-02 02:12:02 +00:00
|
|
|
|
2023-11-07 23:55:58 +00:00
|
|
|
macaddr_factory_e006: macaddr@e006 {
|
2024-06-15 01:20:50 +00:00
|
|
|
compatible = "mac-base";
|
2023-11-07 23:55:58 +00:00
|
|
|
reg = <0xe006 0x6>;
|
2024-06-15 01:20:50 +00:00
|
|
|
#nvmem-cell-cells = <1>;
|
2023-11-07 23:55:58 +00:00
|
|
|
};
|
2023-10-02 02:12:02 +00:00
|
|
|
};
|
ramips: add support for D-Link DIR-882 R1
Specifications:
- SoC: MediaTek MT7621AT
- RAM: 128 MB (DDR3)
- Flash: 16 MB (SPI NOR)
- WiFi: MediaTek MT7615N (x2)
- Switch: 1 WAN, 4 LAN (Gigabit)
- Ports: 1 USB 2.0, 1 USB 3.0
- Buttons: Reset, WiFi Toggle, WPS
- LEDs: Power, Internet, WiFi 2.4G WiFi 5G, USB 2.0, USB 3.0
The R1 revision is identical to the A1 revision except
- No Config2 Parition, therefore
- factory partition resized to 64k from 128K
- Firmware partition offset is 0x50000 not 0x60000
- Firmware partitions size increased by 64K
- Firmware partition type is "denx,uimage", not "sge,uimage"
- Padding of image creation "uimage-padhdr 96" removed
Installation:
- Older firmware versions: put the factory image on a USB stick, turn on
the telnet console, and flash using the following cmd
"fw_updater Linux /mnt/usb_X_X/firmware.bin"
- D-Link FailsafeUI:
Power down the router, press and hold the reset button, then
re-plug it. Keep the reset button pressed until the internet LED stops
flashing, then jack into any lan port and manually assign a static IP
address in 192.168.0.0/24 other than 192.168.0.0 (e.g. 192.168.0.2)
and go to http://192.168.0.1
Flash with the factory image.
Signed-off-by: Andrew Pikler <andrew.pikler@gmail.com>
2020-10-05 14:16:44 +00:00
|
|
|
};
|
|
|
|
|
|
|
|
partition@50000 {
|
|
|
|
compatible = "denx,uimage";
|
|
|
|
label = "firmware";
|
|
|
|
reg = <0x50000 0xfb0000>;
|
|
|
|
};
|
|
|
|
};
|
|
|
|
};
|
|
|
|
};
|