openwrt/target/linux/realtek/patches-5.4/703-include-linux-add-phy-ops-for-rtl838x.patch

14 lines
555 B
Diff
Raw Normal View History

rtl838x: add new architecture This adds support for the RTL838x Architecture. SoCs of this type are used in managed and un-managed Switches and Routers with 8-28 ports. Drivers are provided for SoC initialization, GPIOs, Flash, Ethernet including a DSA switch driver and internal and external PHYs used with these switches. Supported SoCs: RTL8380M RTL8381M RTL8382M The kernel will also boot on the following RTL839x SoCs, however driver support apart from spi-nor is missing: RTL8390 RTL8391 RTL8393 The following PHYs are supported: RTL8214FC (Quad QSGMII multiplexing GMAC and SFP port) RTL8218B internal: internal PHY of the RTL838x chips RTL8318b external (QSGMII 8-port GMAC phy) RTL8382M SerDes for 2 SFP ports Initialization sequences for the PHYs are provided in the form of firmware files. Flash driver supports 3 / 4 byte access DSA switch driver supports VLANs, port isolation, STP and port mirroring. The ALLNET ALL-SG8208M is supported as Proof of Concept: RTL8382M SoC 1 MIPS 4KEc core @ 500MHz 8 Internal PHYs (RTL8218B) 128MB DRAM (Nanya NT5TU128MB) 16MB NOR Flash (MXIC 25L128) 8 GBEthernet ports with one green status LED each (SoC controlled) 1 Power LED (not configurable) 1 SYS LED (configurable) 1 On-Off switch (not configurable) 1 Reset button at the right behind right air-vent (not configurable) 1 Reset button on front panel (configurable) 12V 1A barrel connector 1 serial header with populated standard pin connector and with markings GND TX RX Vcc(3.3V), connection properties: 115200 8N1 To install, upload the sysupgrade image to the OEM webpage. Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2020-09-13 07:06:13 +00:00
--- a/include/linux/phy.h
+++ b/include/linux/phy.h
@@ -644,6 +644,10 @@ struct phy_driver {
rtl838x: add new architecture This adds support for the RTL838x Architecture. SoCs of this type are used in managed and un-managed Switches and Routers with 8-28 ports. Drivers are provided for SoC initialization, GPIOs, Flash, Ethernet including a DSA switch driver and internal and external PHYs used with these switches. Supported SoCs: RTL8380M RTL8381M RTL8382M The kernel will also boot on the following RTL839x SoCs, however driver support apart from spi-nor is missing: RTL8390 RTL8391 RTL8393 The following PHYs are supported: RTL8214FC (Quad QSGMII multiplexing GMAC and SFP port) RTL8218B internal: internal PHY of the RTL838x chips RTL8318b external (QSGMII 8-port GMAC phy) RTL8382M SerDes for 2 SFP ports Initialization sequences for the PHYs are provided in the form of firmware files. Flash driver supports 3 / 4 byte access DSA switch driver supports VLANs, port isolation, STP and port mirroring. The ALLNET ALL-SG8208M is supported as Proof of Concept: RTL8382M SoC 1 MIPS 4KEc core @ 500MHz 8 Internal PHYs (RTL8218B) 128MB DRAM (Nanya NT5TU128MB) 16MB NOR Flash (MXIC 25L128) 8 GBEthernet ports with one green status LED each (SoC controlled) 1 Power LED (not configurable) 1 SYS LED (configurable) 1 On-Off switch (not configurable) 1 Reset button at the right behind right air-vent (not configurable) 1 Reset button on front panel (configurable) 12V 1A barrel connector 1 serial header with populated standard pin connector and with markings GND TX RX Vcc(3.3V), connection properties: 115200 8N1 To install, upload the sysupgrade image to the OEM webpage. Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2020-09-13 07:06:13 +00:00
struct ethtool_tunable *tuna,
const void *data);
int (*set_loopback)(struct phy_device *dev, bool enable);
+ int (*get_port)(struct phy_device *dev);
+ int (*set_port)(struct phy_device *dev, int port);
+ int (*get_eee)(struct phy_device *dev, struct ethtool_eee *e);
+ int (*set_eee)(struct phy_device *dev, struct ethtool_eee *e);
};
#define to_phy_driver(d) container_of(to_mdio_common_driver(d), \
struct phy_driver, mdiodrv)