openwrt/target/linux/generic/backport-4.19/741-v5.5-net-phylink-fix-link-mode-modification-in-PHY-mode.patch

From 4c9633f75dc35abe1b9261e0415d77802f35741d Mon Sep 17 00:00:00 2001
From: Russell King <rmk+kernel@armlinux.org.uk>
Date: Tue, 5 Nov 2019 11:58:00 +0000
Subject: [PATCH 639/660] net: phylink: fix link mode modification in PHY mode

Modifying the link settings via phylink_ethtool_ksettings_set() and
phylink_ethtool_set_pauseparam() didn't always work as intended for
PHY based setups, as calling phylink_mac_config() would result in the
unresolved configuration being committed to the MAC, rather than the
configuration with the speed and duplex setting.

This would work fine if the update caused the link to renegotiate,
but if no settings have changed, phylib won't trigger a renegotiation
cycle, and the MAC will be left incorrectly configured.

Avoid calling phylink_mac_config() unless we are using an inband mode
in phylink_ethtool_ksettings_set(), and use phy_set_asym_pause() as
introduced in 4.20 to set the PHY settings in
phylink_ethtool_set_pauseparam().

Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
---
 drivers/net/phy/phylink.c | 24 ++++++++++++++++--------
 1 file changed, 16 insertions(+), 8 deletions(-)

--- a/drivers/net/phy/phylink.c
+++ b/drivers/net/phy/phylink.c
@@ -1210,7 +1210,13 @@ int phylink_ethtool_ksettings_set(struct
 	pl->link_config.duplex = our_kset.base.duplex;
 	pl->link_config.an_enabled = our_kset.base.autoneg != AUTONEG_DISABLE;
 
-	if (!test_bit(PHYLINK_DISABLE_STOPPED, &pl->phylink_disable_state)) {
+	/* If we have a PHY, phylib will call our link state function if the
+	 * mode has changed, which will trigger a resolve and update the MAC
+	 * configuration. For a fixed link, this isn't able to change any
+	 * parameters, which just leaves inband mode.
+	 */
+	if (pl->link_an_mode == MLO_AN_INBAND &&
+	    !test_bit(PHYLINK_DISABLE_STOPPED, &pl->phylink_disable_state)) {
 		phylink_mac_config(pl, &pl->link_config);
 		phylink_mac_an_restart(pl);
 	}
@@ -1290,14 +1296,16 @@ int phylink_ethtool_set_pauseparam(struc
 	if (pause->tx_pause)
 		config->pause |= MLO_PAUSE_TX;
 
-	if (!test_bit(PHYLINK_DISABLE_STOPPED, &pl->phylink_disable_state)) {
+	/* If we have a PHY, phylib will call our link state function if the
+	 * mode has changed, which will trigger a resolve and update the MAC
+	 * configuration.
+	 */
+	if (pl->phydev) {
+		phy_set_asym_pause(pl->phydev, pause->rx_pause,
+				   pause->tx_pause);
+	} else if (!test_bit(PHYLINK_DISABLE_STOPPED,
+			     &pl->phylink_disable_state)) {
 		switch (pl->link_an_mode) {
-		case MLO_AN_PHY:
-			/* Silently mark the carrier down, and then trigger a resolve */
-			netif_carrier_off(pl->netdev);
-			phylink_run_resolve(pl);
-			break;
-
 		case MLO_AN_FIXED:
 			/* Should we allow fixed links to change against the config? */
 			phylink_resolve_flow(pl, config);