openwrt/target/linux/ramips/dts/mt7628an_asus_rt-ac1200.dts

29 lines
560 B
Plaintext
Raw Normal View History

ramips: add support for Asus RT-AC1200 Asus RT-AC1200 is a 2.4/5GHz dual band AC router, based on MediaTek MT7628AN. Specification: * SoC: MT7628AN * RAM: DDR2 64 MiB * Flash: 16 MiB NOR (W25Q128BV) * Wi-Fi: * 2.4GHz: SoC Built-in * 5GHz: MT7612EN * Ethernet: 5x 100Mbps * Switch: SoC built-in * USB: 1x 2.0 Flash Layout: 0x0000000-0x0030000 : "bootloader" 0x0030000-0x0040000 : "nvram" 0x0040000-0x0050000 : "factory" 0x0050000-0x1000000 : "firmware" MAC address: LAN: factory 0x28 WAN: factory 0x22 2.4G: factory 0x4 5G: factory 0x8004 Installation via **recovery** mode: 1. Download the Asus recovery firmware (windows) tool from http://dlcdnet.asus.com/pub/ASUS/LiveUpdate/Release/Wireless/Rescue.zip 2. Set your ethernet IP manually 192.168.1.5 / 255.255.255.0 with NO gateway. 3. Plug in your ethernet to LAN port 1 on the router. 4. Load up the recovery software with the firmware file, but don't press "Upload" yet. 5. Plug in the router to power WHILE HOLDING the reset button in. While CONTINUING to hold the button, select "Upload" Continue to hold the reset button in until it finishes and verifies! 6. If that doesn't work try pressing "Upload" first just before you do step 5. At some point while holding reset the rescue tool will finally detect and upload the firmware. That's when you can let go of the reset button. 7. The router will reboot and not much will happen. Wait a minute or 2. 8. Power off and on the router again. Voila. Set everything your Ethernet IP back to DHCP (automatically) and you're good to go. Revert to stock firmware: 1. Install stock image via recovery mode. Tested-by: Ivan Pavlov <AuthorReflex@gmail.com> Signed-off-by: Ray Wang <raywang777@foxmail.com>
2022-02-10 15:16:05 +00:00
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
// Copyright (c) 2022 Ray Wang
// Copyright (c) 2022 Ivan Pavlov
ramips: add support for ASUS RT-AC1200-V2 Hardware specifications: SoC: MT7628DAN MIPS_24KEc@580MHz 2.4G-n 2x2 WiFi: MT7613BEN 5G-ac 160MHz 2x2 Switch: 4x100M built-in SoC Flash: 16MB W25Q128JVSQ SPI-NOR DRAM: 64MB built-in SoC MAC addresses as verified by OEM firmware: use address source Lan/Wan/2G *:60 factory 0x4 (label) 5G *:64 factory 0x8000 Serial console: 57600,8n1 Installation: Asus windows recovery tool: install the Asus firmware restoration utility unplug the router, hold the reset button while powering it on release when the power LED flashes slowly specify a static IP on your computer: IP address: 192.168.1.75 Subnet mask 255.255.255.0 start the Asus firmware restoration utility, specify the factory image and press upload do NOT power off the device after OpenWrt has booted until the LED flashing after flashing OpenWrt, there will be first no 5GHz Wifi available probably, wait until blinking finishes and do a reboot TFTP Recovery method: set computer to a static ip, 192.168.1.75 connect computer to the LAN 1 port of the router hold the reset button while powering on the router for a few seconds send firmware image using a tftp client; i.e from linux: $ tftp tftp> binary tftp> connect 192.168.1.1 tftp> put factory.bin tftp> quit do NOT power off the device after OpenWrt has booted until the LED flashing after flashing OpenWrt, there will be first no 5GHz Wifi available probably, wait until blinking finishes and do a reboot Signed-off-by: Tamas Balogh <tamasbalogh@hotmail.com> (cherry picked from commit a4bf562aa71ad1e3dcffa392b79110d803a93f11)
2022-04-15 09:11:01 +00:00
#include "mt7628an_asus_rt-ac1200.dtsi"
ramips: add support for Asus RT-AC1200 Asus RT-AC1200 is a 2.4/5GHz dual band AC router, based on MediaTek MT7628AN. Specification: * SoC: MT7628AN * RAM: DDR2 64 MiB * Flash: 16 MiB NOR (W25Q128BV) * Wi-Fi: * 2.4GHz: SoC Built-in * 5GHz: MT7612EN * Ethernet: 5x 100Mbps * Switch: SoC built-in * USB: 1x 2.0 Flash Layout: 0x0000000-0x0030000 : "bootloader" 0x0030000-0x0040000 : "nvram" 0x0040000-0x0050000 : "factory" 0x0050000-0x1000000 : "firmware" MAC address: LAN: factory 0x28 WAN: factory 0x22 2.4G: factory 0x4 5G: factory 0x8004 Installation via **recovery** mode: 1. Download the Asus recovery firmware (windows) tool from http://dlcdnet.asus.com/pub/ASUS/LiveUpdate/Release/Wireless/Rescue.zip 2. Set your ethernet IP manually 192.168.1.5 / 255.255.255.0 with NO gateway. 3. Plug in your ethernet to LAN port 1 on the router. 4. Load up the recovery software with the firmware file, but don't press "Upload" yet. 5. Plug in the router to power WHILE HOLDING the reset button in. While CONTINUING to hold the button, select "Upload" Continue to hold the reset button in until it finishes and verifies! 6. If that doesn't work try pressing "Upload" first just before you do step 5. At some point while holding reset the rescue tool will finally detect and upload the firmware. That's when you can let go of the reset button. 7. The router will reboot and not much will happen. Wait a minute or 2. 8. Power off and on the router again. Voila. Set everything your Ethernet IP back to DHCP (automatically) and you're good to go. Revert to stock firmware: 1. Install stock image via recovery mode. Tested-by: Ivan Pavlov <AuthorReflex@gmail.com> Signed-off-by: Ray Wang <raywang777@foxmail.com>
2022-02-10 15:16:05 +00:00
/ {
compatible = "asus,rt-ac1200", "mediatek,mt7628an-soc";
model = "Asus RT-AC1200";
leds {
compatible = "gpio-leds";
usb {
label = "blue:usb";
gpios = <&gpio 6 GPIO_ACTIVE_HIGH>;
trigger-sources = <&ohci_port1>, <&ehci_port1>;
linux,default-trigger = "usbport";
};
};
};
&state_default {
gpio {
groups = "i2c", "spi cs1", "refclk", "wled_an";
function = "gpio";
};
};