openwrt/target/linux/ipq40xx/files/drivers/net/phy/qca807x.c

// SPDX-License-Identifier: GPL-2.0-or-later
/*
 * Copyright (c) 2020 Sartura Ltd.
 *
 * Author: Robert Marko <robert.marko@sartura.hr>
 *
 * Qualcomm QCA8072 and QCA8075 PHY driver
 */

#include <linux/version.h>
#include <linux/module.h>
#include <linux/of.h>
#include <linux/phy.h>
#include <linux/bitfield.h>
#if LINUX_VERSION_CODE >= KERNEL_VERSION(5,8,0)
#include <linux/ethtool_netlink.h>
#endif
#include <linux/gpio.h>
#include <linux/sfp.h>

#include <dt-bindings/net/qcom-qca807x.h>

#define PHY_ID_QCA8072		0x004dd0b2
#define PHY_ID_QCA8075		0x004dd0b1
#define PHY_ID_QCA807X_PSGMII	0x06820805

/* Downshift */
#define QCA807X_SMARTSPEED_EN			BIT(5)
#define QCA807X_SMARTSPEED_RETRY_LIMIT_MASK	GENMASK(4, 2)
#define QCA807X_SMARTSPEED_RETRY_LIMIT_DEFAULT	5
#define QCA807X_SMARTSPEED_RETRY_LIMIT_MIN	2
#define QCA807X_SMARTSPEED_RETRY_LIMIT_MAX	9

/* Cable diagnostic test (CDT) */
#define QCA807X_CDT						0x16
#define QCA807X_CDT_ENABLE					BIT(15)
#define QCA807X_CDT_ENABLE_INTER_PAIR_SHORT			BIT(13)
#define QCA807X_CDT_STATUS					BIT(11)
#define QCA807X_CDT_MMD3_STATUS					0x8064
#define QCA807X_CDT_MDI0_STATUS_MASK				GENMASK(15, 12)
#define QCA807X_CDT_MDI1_STATUS_MASK				GENMASK(11, 8)
#define QCA807X_CDT_MDI2_STATUS_MASK				GENMASK(7, 4)
#define QCA807X_CDT_MDI3_STATUS_MASK				GENMASK(3, 0)
#define QCA807X_CDT_RESULTS_INVALID				0x0
#define QCA807X_CDT_RESULTS_OK					0x1
#define QCA807X_CDT_RESULTS_OPEN				0x2
#define QCA807X_CDT_RESULTS_SAME_SHORT				0x3
#define QCA807X_CDT_RESULTS_CROSS_SHORT_WITH_MDI1_SAME_OK	0x4
#define QCA807X_CDT_RESULTS_CROSS_SHORT_WITH_MDI2_SAME_OK	0x8
#define QCA807X_CDT_RESULTS_CROSS_SHORT_WITH_MDI3_SAME_OK	0xc
#define QCA807X_CDT_RESULTS_CROSS_SHORT_WITH_MDI1_SAME_OPEN	0x6
#define QCA807X_CDT_RESULTS_CROSS_SHORT_WITH_MDI2_SAME_OPEN	0xa
#define QCA807X_CDT_RESULTS_CROSS_SHORT_WITH_MDI3_SAME_OPEN	0xe
#define QCA807X_CDT_RESULTS_CROSS_SHORT_WITH_MDI1_SAME_SHORT	0x7
#define QCA807X_CDT_RESULTS_CROSS_SHORT_WITH_MDI2_SAME_SHORT	0xb
#define QCA807X_CDT_RESULTS_CROSS_SHORT_WITH_MDI3_SAME_SHORT	0xf
#define QCA807X_CDT_RESULTS_BUSY				0x9
#define QCA807X_CDT_MMD3_MDI0_LENGTH				0x8065
#define QCA807X_CDT_MMD3_MDI1_LENGTH				0x8066
#define QCA807X_CDT_MMD3_MDI2_LENGTH				0x8067
#define QCA807X_CDT_MMD3_MDI3_LENGTH				0x8068
#define QCA807X_CDT_SAME_SHORT_LENGTH_MASK			GENMASK(15, 8)
#define QCA807X_CDT_CROSS_SHORT_LENGTH_MASK			GENMASK(7, 0)

#define QCA807X_CHIP_CONFIGURATION				0x1f
#define QCA807X_BT_BX_REG_SEL					BIT(15)
#define QCA807X_CHIP_CONFIGURATION_MODE_CFG_MASK		GENMASK(3, 0)
#define QCA807X_CHIP_CONFIGURATION_MODE_QSGMII_SGMII		4
#define QCA807X_CHIP_CONFIGURATION_MODE_PSGMII_FIBER		3
#define QCA807X_CHIP_CONFIGURATION_MODE_PSGMII_ALL_COPPER	0

#define QCA807X_MEDIA_SELECT_STATUS				0x1a
#define QCA807X_MEDIA_DETECTED_COPPER				BIT(5)
#define QCA807X_MEDIA_DETECTED_1000_BASE_X			BIT(4)
#define QCA807X_MEDIA_DETECTED_100_BASE_FX			BIT(3)

#define QCA807X_MMD7_FIBER_MODE_AUTO_DETECTION			0x807e
#define QCA807X_MMD7_FIBER_MODE_AUTO_DETECTION_EN		BIT(0)

#define QCA807X_MMD7_1000BASE_T_POWER_SAVE_PER_CABLE_LENGTH	0x801a
#define QCA807X_CONTROL_DAC_MASK				GENMASK(2, 0)

#define QCA807X_MMD7_LED_100N_1				0x8074
#define QCA807X_MMD7_LED_100N_2				0x8075
#define QCA807X_MMD7_LED_1000N_1			0x8076
#define QCA807X_MMD7_LED_1000N_2			0x8077
#define QCA807X_LED_TXACT_BLK_EN_2			BIT(10)
#define QCA807X_LED_RXACT_BLK_EN_2			BIT(9)
#define QCA807X_LED_GT_ON_EN_2				BIT(6)
#define QCA807X_LED_HT_ON_EN_2				BIT(5)
#define QCA807X_LED_BT_ON_EN_2				BIT(4)
#define QCA807X_GPIO_FORCE_EN				BIT(15)
#define QCA807X_GPIO_FORCE_MODE_MASK			GENMASK(14, 13)

#define QCA807X_INTR_ENABLE				0x12
#define QCA807X_INTR_STATUS				0x13
#define QCA807X_INTR_ENABLE_AUTONEG_ERR			BIT(15)
#define QCA807X_INTR_ENABLE_SPEED_CHANGED		BIT(14)
#define QCA807X_INTR_ENABLE_DUPLEX_CHANGED		BIT(13)
#define QCA807X_INTR_ENABLE_LINK_FAIL			BIT(11)
#define QCA807X_INTR_ENABLE_LINK_SUCCESS		BIT(10)

#define QCA807X_FUNCTION_CONTROL			0x10
#define QCA807X_FC_MDI_CROSSOVER_MODE_MASK		GENMASK(6, 5)
#define QCA807X_FC_MDI_CROSSOVER_AUTO			3
#define QCA807X_FC_MDI_CROSSOVER_MANUAL_MDIX		1
#define QCA807X_FC_MDI_CROSSOVER_MANUAL_MDI		0

#define QCA807X_PHY_SPECIFIC_STATUS			0x11
#define QCA807X_SS_SPEED_AND_DUPLEX_RESOLVED		BIT(11)
#define QCA807X_SS_SPEED_MASK				GENMASK(15, 14)
#define QCA807X_SS_SPEED_1000				2
#define QCA807X_SS_SPEED_100				1
#define QCA807X_SS_SPEED_10				0
#define QCA807X_SS_DUPLEX				BIT(13)
#define QCA807X_SS_MDIX					BIT(6)

/* PSGMII PHY specific */
#define PSGMII_QSGMII_DRIVE_CONTROL_1			0xb
#define PSGMII_QSGMII_TX_DRIVER_MASK			GENMASK(7, 4)
#define PSGMII_MODE_CTRL				0x6d
#define PSGMII_MODE_CTRL_AZ_WORKAROUND_MASK		GENMASK(3, 0)
#define PSGMII_MMD3_SERDES_CONTROL			0x805a

struct qca807x_gpio_priv {
	struct phy_device *phy;
};

static int qca807x_get_downshift(struct phy_device *phydev, u8 *data)
{
	int val, cnt, enable;

	val = phy_read(phydev, MII_NWAYTEST);
	if (val < 0)
		return val;

	enable = FIELD_GET(QCA807X_SMARTSPEED_EN, val);
	cnt = FIELD_GET(QCA807X_SMARTSPEED_RETRY_LIMIT_MASK, val) + 2;

	*data = enable ? cnt : DOWNSHIFT_DEV_DISABLE;

	return 0;
}

static int qca807x_set_downshift(struct phy_device *phydev, u8 cnt)
{
	int ret, val;

	if (cnt > QCA807X_SMARTSPEED_RETRY_LIMIT_MAX ||
	    (cnt < QCA807X_SMARTSPEED_RETRY_LIMIT_MIN && cnt != DOWNSHIFT_DEV_DISABLE))
		return -EINVAL;

	if (!cnt) {
		ret = phy_clear_bits(phydev, MII_NWAYTEST, QCA807X_SMARTSPEED_EN);
	} else {
		val = QCA807X_SMARTSPEED_EN;
		val |= FIELD_PREP(QCA807X_SMARTSPEED_RETRY_LIMIT_MASK, cnt - 2);

		phy_modify(phydev, MII_NWAYTEST,
			   QCA807X_SMARTSPEED_EN |
			   QCA807X_SMARTSPEED_RETRY_LIMIT_MASK,
			   val);
	}

	ret = genphy_soft_reset(phydev);

	return ret;
}

static int qca807x_get_tunable(struct phy_device *phydev,
			       struct ethtool_tunable *tuna, void *data)
{
	switch (tuna->id) {
	case ETHTOOL_PHY_DOWNSHIFT:
		return qca807x_get_downshift(phydev, data);
	default:
		return -EOPNOTSUPP;
	}
}

static int qca807x_set_tunable(struct phy_device *phydev,
			       struct ethtool_tunable *tuna, const void *data)
{
	switch (tuna->id) {
	case ETHTOOL_PHY_DOWNSHIFT:
		return qca807x_set_downshift(phydev, *(const u8 *)data);
	default:
		return -EOPNOTSUPP;
	}
}

#if LINUX_VERSION_CODE >= KERNEL_VERSION(5,8,0)
static bool qca807x_distance_valid(int result)
{
	switch (result) {
	case QCA807X_CDT_RESULTS_OPEN:
	case QCA807X_CDT_RESULTS_SAME_SHORT:
	case QCA807X_CDT_RESULTS_CROSS_SHORT_WITH_MDI1_SAME_OK:
	case QCA807X_CDT_RESULTS_CROSS_SHORT_WITH_MDI2_SAME_OK:
	case QCA807X_CDT_RESULTS_CROSS_SHORT_WITH_MDI3_SAME_OK:
	case QCA807X_CDT_RESULTS_CROSS_SHORT_WITH_MDI1_SAME_OPEN:
	case QCA807X_CDT_RESULTS_CROSS_SHORT_WITH_MDI2_SAME_OPEN:
	case QCA807X_CDT_RESULTS_CROSS_SHORT_WITH_MDI3_SAME_OPEN:
	case QCA807X_CDT_RESULTS_CROSS_SHORT_WITH_MDI1_SAME_SHORT:
	case QCA807X_CDT_RESULTS_CROSS_SHORT_WITH_MDI2_SAME_SHORT:
	case QCA807X_CDT_RESULTS_CROSS_SHORT_WITH_MDI3_SAME_SHORT:
		return true;
	}
	return false;
}

static int qca807x_report_length(struct phy_device *phydev,
				 int pair, int result)
{
	int length;
	int ret;

	ret = phy_read_mmd(phydev, MDIO_MMD_PCS, QCA807X_CDT_MMD3_MDI0_LENGTH + pair);
	if (ret < 0)
		return ret;

	switch (result) {
	case ETHTOOL_A_CABLE_RESULT_CODE_SAME_SHORT:
		length = (FIELD_GET(QCA807X_CDT_SAME_SHORT_LENGTH_MASK, ret) * 800) / 10;
		break;
	case ETHTOOL_A_CABLE_RESULT_CODE_OPEN:
	case ETHTOOL_A_CABLE_RESULT_CODE_CROSS_SHORT:
		length = (FIELD_GET(QCA807X_CDT_CROSS_SHORT_LENGTH_MASK, ret) * 800) / 10;
		break;
	}

	ethnl_cable_test_fault_length(phydev, pair, length);

	return 0;
}

static int qca807x_cable_test_report_trans(int result)
{
	switch (result) {
	case QCA807X_CDT_RESULTS_OK:
		return ETHTOOL_A_CABLE_RESULT_CODE_OK;
	case QCA807X_CDT_RESULTS_OPEN:
		return ETHTOOL_A_CABLE_RESULT_CODE_OPEN;
	case QCA807X_CDT_RESULTS_SAME_SHORT:
		return ETHTOOL_A_CABLE_RESULT_CODE_SAME_SHORT;
	case QCA807X_CDT_RESULTS_CROSS_SHORT_WITH_MDI1_SAME_OK:
	case QCA807X_CDT_RESULTS_CROSS_SHORT_WITH_MDI2_SAME_OK:
	case QCA807X_CDT_RESULTS_CROSS_SHORT_WITH_MDI3_SAME_OK:
	case QCA807X_CDT_RESULTS_CROSS_SHORT_WITH_MDI1_SAME_OPEN:
	case QCA807X_CDT_RESULTS_CROSS_SHORT_WITH_MDI2_SAME_OPEN:
	case QCA807X_CDT_RESULTS_CROSS_SHORT_WITH_MDI3_SAME_OPEN:
	case QCA807X_CDT_RESULTS_CROSS_SHORT_WITH_MDI1_SAME_SHORT:
	case QCA807X_CDT_RESULTS_CROSS_SHORT_WITH_MDI2_SAME_SHORT:
	case QCA807X_CDT_RESULTS_CROSS_SHORT_WITH_MDI3_SAME_SHORT:
		return ETHTOOL_A_CABLE_RESULT_CODE_CROSS_SHORT;
	default:
		return ETHTOOL_A_CABLE_RESULT_CODE_UNSPEC;
	}
}

static int qca807x_cable_test_report(struct phy_device *phydev)
{
	int pair0, pair1, pair2, pair3;
	int ret;

	ret = phy_read_mmd(phydev, MDIO_MMD_PCS, QCA807X_CDT_MMD3_STATUS);
	if (ret < 0)
		return ret;

	pair0 = FIELD_GET(QCA807X_CDT_MDI0_STATUS_MASK, ret);
	pair1 = FIELD_GET(QCA807X_CDT_MDI1_STATUS_MASK, ret);
	pair2 = FIELD_GET(QCA807X_CDT_MDI2_STATUS_MASK, ret);
	pair3 = FIELD_GET(QCA807X_CDT_MDI3_STATUS_MASK, ret);

	ethnl_cable_test_result(phydev, ETHTOOL_A_CABLE_PAIR_A,
				qca807x_cable_test_report_trans(pair0));
	ethnl_cable_test_result(phydev, ETHTOOL_A_CABLE_PAIR_B,
				qca807x_cable_test_report_trans(pair1));
	ethnl_cable_test_result(phydev, ETHTOOL_A_CABLE_PAIR_C,
				qca807x_cable_test_report_trans(pair2));
	ethnl_cable_test_result(phydev, ETHTOOL_A_CABLE_PAIR_D,
				qca807x_cable_test_report_trans(pair3));

	if (qca807x_distance_valid(pair0))
		qca807x_report_length(phydev, 0, qca807x_cable_test_report_trans(pair0));
	if (qca807x_distance_valid(pair1))
		qca807x_report_length(phydev, 1, qca807x_cable_test_report_trans(pair1));
	if (qca807x_distance_valid(pair2))
		qca807x_report_length(phydev, 2, qca807x_cable_test_report_trans(pair2));
	if (qca807x_distance_valid(pair3))
		qca807x_report_length(phydev, 3, qca807x_cable_test_report_trans(pair3));

	return 0;
}

static int qca807x_cable_test_get_status(struct phy_device *phydev,
					 bool *finished)
{
	int val;

	*finished = false;

	val = phy_read(phydev, QCA807X_CDT);
	if (!((val & QCA807X_CDT_ENABLE) && (val & QCA807X_CDT_STATUS))) {
		*finished = true;

		return qca807x_cable_test_report(phydev);
	}

	return 0;
}

static int qca807x_cable_test_start(struct phy_device *phydev)
{
	int val, ret;

	val = phy_read(phydev, QCA807X_CDT);
	/* Enable inter-pair short check as well */
	val &= ~QCA807X_CDT_ENABLE_INTER_PAIR_SHORT;
	val |= QCA807X_CDT_ENABLE;
	ret = phy_write(phydev, QCA807X_CDT, val);

	return ret;
}
#endif

#ifdef CONFIG_GPIOLIB
static int qca807x_gpio_get_direction(struct gpio_chip *gc, unsigned int offset)
{
#if LINUX_VERSION_CODE >= KERNEL_VERSION(5,5,0)
	return GPIO_LINE_DIRECTION_OUT;
#else
	return GPIOF_DIR_OUT;
#endif
}

static int qca807x_gpio_get_reg(unsigned int offset)
{
	return QCA807X_MMD7_LED_100N_2 + (offset % 2) * 2;
}

static int qca807x_gpio_get(struct gpio_chip *gc, unsigned int offset)
{
	struct qca807x_gpio_priv *priv = gpiochip_get_data(gc);
	int val;

	val = phy_read_mmd(priv->phy, MDIO_MMD_AN, qca807x_gpio_get_reg(offset));

	return FIELD_GET(QCA807X_GPIO_FORCE_MODE_MASK, val);
}

static void qca807x_gpio_set(struct gpio_chip *gc, unsigned int offset, int value)
{
	struct qca807x_gpio_priv *priv = gpiochip_get_data(gc);
	int val;

	val = phy_read_mmd(priv->phy, MDIO_MMD_AN, qca807x_gpio_get_reg(offset));
	val &= ~QCA807X_GPIO_FORCE_MODE_MASK;
	val |= QCA807X_GPIO_FORCE_EN;
	val |= FIELD_PREP(QCA807X_GPIO_FORCE_MODE_MASK, value);

	phy_write_mmd(priv->phy, MDIO_MMD_AN, qca807x_gpio_get_reg(offset), val);
}

static int qca807x_gpio_dir_out(struct gpio_chip *gc, unsigned int offset, int value)
{
	qca807x_gpio_set(gc, offset, value);

	return 0;
}

static int qca807x_gpio(struct phy_device *phydev)
{
	struct device *dev = &phydev->mdio.dev;
	struct qca807x_gpio_priv *priv;
	struct gpio_chip *gc;

	priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
	if (!priv)
		return -ENOMEM;

	priv->phy = phydev;

	gc = devm_kzalloc(dev, sizeof(*gc), GFP_KERNEL);
	if (!gc)
		return -ENOMEM;

	gc->label = dev_name(dev);
	gc->base = -1;
	gc->ngpio = 2;
	gc->parent = dev;
	gc->owner = THIS_MODULE;
	gc->can_sleep = true;
	gc->get_direction = qca807x_gpio_get_direction;
	gc->direction_output = qca807x_gpio_dir_out;
	gc->get = qca807x_gpio_get;
	gc->set = qca807x_gpio_set;

	return devm_gpiochip_add_data(dev, gc, priv);
}
#endif

static int qca807x_read_copper_status(struct phy_device *phydev, bool combo_port)
{
	int ss, err, page, old_link = phydev->link;

	/* Only combo port has dual pages */
	if (combo_port) {
		/* Check whether copper page is set and set if needed */
		page = phy_read(phydev, QCA807X_CHIP_CONFIGURATION);
		if (!(page & QCA807X_BT_BX_REG_SEL)) {
			page |= QCA807X_BT_BX_REG_SEL;
			phy_write(phydev, QCA807X_CHIP_CONFIGURATION, page);
		}
	}

	/* Update the link, but return if there was an error */
	err = genphy_update_link(phydev);
	if (err)
		return err;

	/* why bother the PHY if nothing can have changed */
	if (phydev->autoneg == AUTONEG_ENABLE && old_link && phydev->link)
		return 0;

	phydev->speed = SPEED_UNKNOWN;
	phydev->duplex = DUPLEX_UNKNOWN;
	phydev->pause = 0;
	phydev->asym_pause = 0;

	err = genphy_read_lpa(phydev);
	if (err < 0)
		return err;

	/* Read the QCA807x PHY-Specific Status register copper page,
	 * which indicates the speed and duplex that the PHY is actually
	 * using, irrespective of whether we are in autoneg mode or not.
	 */
	ss = phy_read(phydev, QCA807X_PHY_SPECIFIC_STATUS);
	if (ss < 0)
		return ss;

	if (ss & QCA807X_SS_SPEED_AND_DUPLEX_RESOLVED) {
		int sfc;

		sfc = phy_read(phydev, QCA807X_FUNCTION_CONTROL);
		if (sfc < 0)
			return sfc;

		switch (FIELD_GET(QCA807X_SS_SPEED_MASK, ss)) {
		case QCA807X_SS_SPEED_10:
			phydev->speed = SPEED_10;
			break;
		case QCA807X_SS_SPEED_100:
			phydev->speed = SPEED_100;
			break;
		case QCA807X_SS_SPEED_1000:
			phydev->speed = SPEED_1000;
			break;
		}
		if (ss & QCA807X_SS_DUPLEX)
			phydev->duplex = DUPLEX_FULL;
		else
			phydev->duplex = DUPLEX_HALF;

		if (ss & QCA807X_SS_MDIX)
			phydev->mdix = ETH_TP_MDI_X;
		else
			phydev->mdix = ETH_TP_MDI;

		switch (FIELD_GET(QCA807X_FC_MDI_CROSSOVER_MODE_MASK, sfc)) {
		case QCA807X_FC_MDI_CROSSOVER_MANUAL_MDI:
			phydev->mdix_ctrl = ETH_TP_MDI;
			break;
		case QCA807X_FC_MDI_CROSSOVER_MANUAL_MDIX:
			phydev->mdix_ctrl = ETH_TP_MDI_X;
			break;
		case QCA807X_FC_MDI_CROSSOVER_AUTO:
			phydev->mdix_ctrl = ETH_TP_MDI_AUTO;
			break;
		}
	}

	if (phydev->autoneg == AUTONEG_ENABLE && phydev->autoneg_complete)
		phy_resolve_aneg_pause(phydev);

	return 0;
}

static int qca807x_read_fiber_status(struct phy_device *phydev, bool combo_port)
{
	int ss, err, page, lpa, old_link = phydev->link;

	/* Check whether fiber page is set and set if needed */
	page = phy_read(phydev, QCA807X_CHIP_CONFIGURATION);
	if (page & QCA807X_BT_BX_REG_SEL) {
		page &= ~QCA807X_BT_BX_REG_SEL;
		phy_write(phydev, QCA807X_CHIP_CONFIGURATION, page);
	}

	/* Update the link, but return if there was an error */
	err = genphy_update_link(phydev);
	if (err)
		return err;

	/* why bother the PHY if nothing can have changed */
	if (phydev->autoneg == AUTONEG_ENABLE && old_link && phydev->link)
		return 0;

	phydev->speed = SPEED_UNKNOWN;
	phydev->duplex = DUPLEX_UNKNOWN;
	phydev->pause = 0;
	phydev->asym_pause = 0;

	if (phydev->autoneg == AUTONEG_ENABLE && phydev->autoneg_complete) {
		lpa = phy_read(phydev, MII_LPA);
		if (lpa < 0)
			return lpa;

		linkmode_mod_bit(ETHTOOL_LINK_MODE_Autoneg_BIT,
				 phydev->lp_advertising, lpa & LPA_LPACK);
		linkmode_mod_bit(ETHTOOL_LINK_MODE_1000baseX_Full_BIT,
				 phydev->lp_advertising, lpa & LPA_1000XFULL);
		linkmode_mod_bit(ETHTOOL_LINK_MODE_Pause_BIT,
				 phydev->lp_advertising, lpa & LPA_1000XPAUSE);
		linkmode_mod_bit(ETHTOOL_LINK_MODE_Asym_Pause_BIT,
				 phydev->lp_advertising,
				 lpa & LPA_1000XPAUSE_ASYM);

		phy_resolve_aneg_linkmode(phydev);
	}

	/* Read the QCA807x PHY-Specific Status register fiber page,
	 * which indicates the speed and duplex that the PHY is actually
	 * using, irrespective of whether we are in autoneg mode or not.
	 */
	ss = phy_read(phydev, QCA807X_PHY_SPECIFIC_STATUS);
	if (ss < 0)
		return ss;

	if (ss & QCA807X_SS_SPEED_AND_DUPLEX_RESOLVED) {
		switch (FIELD_GET(QCA807X_SS_SPEED_MASK, ss)) {
		case QCA807X_SS_SPEED_100:
			phydev->speed = SPEED_100;
			break;
		case QCA807X_SS_SPEED_1000:
			phydev->speed = SPEED_1000;
			break;
		}

		if (ss & QCA807X_SS_DUPLEX)
			phydev->duplex = DUPLEX_FULL;
		else
			phydev->duplex = DUPLEX_HALF;
	}

	return 0;
}

static int qca807x_read_status(struct phy_device *phydev)
{
	int val;

	/* Check for Combo port */
	if (phy_read(phydev, QCA807X_CHIP_CONFIGURATION)) {
		/* Check for fiber mode first */
		if (linkmode_test_bit(ETHTOOL_LINK_MODE_FIBRE_BIT, phydev->supported)) {
			/* Check for actual detected media */
			val = phy_read(phydev, QCA807X_MEDIA_SELECT_STATUS);
			if (val & QCA807X_MEDIA_DETECTED_COPPER) {
				qca807x_read_copper_status(phydev, true);
			} else if ((val & QCA807X_MEDIA_DETECTED_1000_BASE_X) ||
				   (val & QCA807X_MEDIA_DETECTED_100_BASE_FX)) {
				qca807x_read_fiber_status(phydev, true);
			}
		} else {
			qca807x_read_copper_status(phydev, true);
		}
	} else {
		qca807x_read_copper_status(phydev, false);
	}

	return 0;
}

static int qca807x_config_intr(struct phy_device *phydev)
{
	int ret, val;

	val = phy_read(phydev, QCA807X_INTR_ENABLE);

	if (phydev->interrupts == PHY_INTERRUPT_ENABLED) {
		/* Check for combo port as it has fewer interrupts */
		if (phy_read(phydev, QCA807X_CHIP_CONFIGURATION)) {
			val |= QCA807X_INTR_ENABLE_SPEED_CHANGED;
			val |= QCA807X_INTR_ENABLE_LINK_FAIL;
			val |= QCA807X_INTR_ENABLE_LINK_SUCCESS;
		} else {
			val |= QCA807X_INTR_ENABLE_AUTONEG_ERR;
			val |= QCA807X_INTR_ENABLE_SPEED_CHANGED;
			val |= QCA807X_INTR_ENABLE_DUPLEX_CHANGED;
			val |= QCA807X_INTR_ENABLE_LINK_FAIL;
			val |= QCA807X_INTR_ENABLE_LINK_SUCCESS;
		}
		ret = phy_write(phydev, QCA807X_INTR_ENABLE, val);
	} else {
		ret = phy_write(phydev, QCA807X_INTR_ENABLE, 0);
	}

	return ret;
}

static int qca807x_ack_intr(struct phy_device *phydev)
{
	int ret;

	ret = phy_read(phydev, QCA807X_INTR_STATUS);

	return (ret < 0) ? ret : 0;
}

static int qca807x_led_config(struct phy_device *phydev)
{
	struct device_node *node = phydev->mdio.dev.of_node;
	bool led_config = false;
	int val;

	val = phy_read_mmd(phydev, MDIO_MMD_AN, QCA807X_MMD7_LED_1000N_1);
	if (val < 0)
		return val;

	if (of_property_read_bool(node, "qcom,single-led-1000")) {
		val |= QCA807X_LED_TXACT_BLK_EN_2;
		val |= QCA807X_LED_RXACT_BLK_EN_2;
		val |= QCA807X_LED_GT_ON_EN_2;

		led_config = true;
	}

	if (of_property_read_bool(node, "qcom,single-led-100")) {
		val |= QCA807X_LED_HT_ON_EN_2;

		led_config = true;
	}

	if (of_property_read_bool(node, "qcom,single-led-10")) {
		val |= QCA807X_LED_BT_ON_EN_2;

		led_config = true;
	}

	if (led_config)
		return phy_write_mmd(phydev, MDIO_MMD_AN, QCA807X_MMD7_LED_1000N_1, val);
	else
		return 0;
}

static const struct sfp_upstream_ops qca807x_sfp_ops = {
	.attach = phy_sfp_attach,
	.detach = phy_sfp_detach,
};

static int qca807x_config(struct phy_device *phydev)
{
	struct device_node *node = phydev->mdio.dev.of_node;
	int control_dac, ret = 0;
	u32 of_control_dac;

	/* Check for Combo port */
	if (phy_read(phydev, QCA807X_CHIP_CONFIGURATION)) {
		int fiber_mode_autodect;
		int psgmii_serdes;
		int chip_config;

		if (of_property_read_bool(node, "qcom,fiber-enable")) {
			/* Enable fiber mode autodection (1000Base-X or 100Base-FX) */
			fiber_mode_autodect = phy_read_mmd(phydev, MDIO_MMD_AN,
							   QCA807X_MMD7_FIBER_MODE_AUTO_DETECTION);
			fiber_mode_autodect |= QCA807X_MMD7_FIBER_MODE_AUTO_DETECTION_EN;
			phy_write_mmd(phydev, MDIO_MMD_AN, QCA807X_MMD7_FIBER_MODE_AUTO_DETECTION,
				      fiber_mode_autodect);

			/* Enable 4 copper + combo port mode */
			chip_config = phy_read(phydev, QCA807X_CHIP_CONFIGURATION);
			chip_config &= ~QCA807X_CHIP_CONFIGURATION_MODE_CFG_MASK;
			chip_config |= FIELD_PREP(QCA807X_CHIP_CONFIGURATION_MODE_CFG_MASK,
						  QCA807X_CHIP_CONFIGURATION_MODE_PSGMII_FIBER);
			phy_write(phydev, QCA807X_CHIP_CONFIGURATION, chip_config);

			linkmode_set_bit(ETHTOOL_LINK_MODE_FIBRE_BIT, phydev->supported);
			linkmode_set_bit(ETHTOOL_LINK_MODE_FIBRE_BIT, phydev->advertising);
		}

		/* Prevent PSGMII going into hibernation via PSGMII self test */
		psgmii_serdes = phy_read_mmd(phydev, MDIO_MMD_PCS, PSGMII_MMD3_SERDES_CONTROL);
		psgmii_serdes &= ~BIT(1);
		ret = phy_write_mmd(phydev, MDIO_MMD_PCS,
				    PSGMII_MMD3_SERDES_CONTROL,
				    psgmii_serdes);
	}

	if (!of_property_read_u32(node, "qcom,control-dac", &of_control_dac)) {
		control_dac = phy_read_mmd(phydev, MDIO_MMD_AN,
					   QCA807X_MMD7_1000BASE_T_POWER_SAVE_PER_CABLE_LENGTH);
		control_dac &= ~QCA807X_CONTROL_DAC_MASK;
		control_dac |= FIELD_PREP(QCA807X_CONTROL_DAC_MASK, of_control_dac);
		ret = phy_write_mmd(phydev, MDIO_MMD_AN,
				    QCA807X_MMD7_1000BASE_T_POWER_SAVE_PER_CABLE_LENGTH,
				    control_dac);
	}

	/* Optionally configure LED-s */
	if (IS_ENABLED(CONFIG_GPIOLIB)) {
		/* Check whether PHY-s pins are used as GPIO-s */
		if (!of_property_read_bool(node, "gpio-controller"))
			ret = qca807x_led_config(phydev);
	} else {
		ret = qca807x_led_config(phydev);
	}

	return ret;
}

static int qca807x_probe(struct phy_device *phydev)
{
	struct device_node *node = phydev->mdio.dev.of_node;
	int ret = 0;

	if (IS_ENABLED(CONFIG_GPIOLIB)) {
		/* Do not register a GPIO controller unless flagged for it */
		if (of_property_read_bool(node, "gpio-controller"))
			ret = qca807x_gpio(phydev);
	}

	/* Attach SFP bus on combo port*/
	if (of_property_read_bool(node, "qcom,fiber-enable")) {
		if (phy_read(phydev, QCA807X_CHIP_CONFIGURATION))
			ret = phy_sfp_probe(phydev, &qca807x_sfp_ops);
	}

	return ret;
}

static int qca807x_psgmii_config(struct phy_device *phydev)
{
	struct device_node *node = phydev->mdio.dev.of_node;
	int psgmii_az, tx_amp, ret = 0;
	u32 tx_driver_strength;

	/* Workaround to enable AZ transmitting ability */
	if (of_property_read_bool(node, "qcom,psgmii-az")) {
		psgmii_az = phy_read_mmd(phydev, MDIO_MMD_PMAPMD, PSGMII_MODE_CTRL);
		psgmii_az &= ~PSGMII_MODE_CTRL_AZ_WORKAROUND_MASK;
		psgmii_az |= FIELD_PREP(PSGMII_MODE_CTRL_AZ_WORKAROUND_MASK, 0xc);
		ret = phy_write_mmd(phydev, MDIO_MMD_PMAPMD, PSGMII_MODE_CTRL, psgmii_az);
		psgmii_az = phy_read_mmd(phydev, MDIO_MMD_PMAPMD, PSGMII_MODE_CTRL);
	}

	/* PSGMII/QSGMII TX amp set to DT defined value instead of default 600mV */
	if (!of_property_read_u32(node, "qcom,tx-driver-strength", &tx_driver_strength)) {
		tx_amp = phy_read(phydev, PSGMII_QSGMII_DRIVE_CONTROL_1);
		tx_amp &= ~PSGMII_QSGMII_TX_DRIVER_MASK;
		tx_amp |= FIELD_PREP(PSGMII_QSGMII_TX_DRIVER_MASK, tx_driver_strength);
		ret = phy_write(phydev, PSGMII_QSGMII_DRIVE_CONTROL_1, tx_amp);
	}

	return ret;
}

static struct phy_driver qca807x_drivers[] = {
	{
		PHY_ID_MATCH_EXACT(PHY_ID_QCA8072),
		.name           = "Qualcomm QCA8072",
#if LINUX_VERSION_CODE >= KERNEL_VERSION(5,8,0)
		.flags		= PHY_POLL_CABLE_TEST,
#endif
		/* PHY_GBIT_FEATURES */
		.probe		= qca807x_probe,
		.config_init	= qca807x_config,
		.read_status	= qca807x_read_status,
		.config_intr	= qca807x_config_intr,
		.ack_interrupt	= qca807x_ack_intr,
		.soft_reset	= genphy_soft_reset,
		.get_tunable	= qca807x_get_tunable,
		.set_tunable	= qca807x_set_tunable,
#if LINUX_VERSION_CODE >= KERNEL_VERSION(5,8,0)
		.cable_test_start	= qca807x_cable_test_start,
		.cable_test_get_status	= qca807x_cable_test_get_status,
#endif
	},
	{
		PHY_ID_MATCH_EXACT(PHY_ID_QCA8075),
		.name           = "Qualcomm QCA8075",
#if LINUX_VERSION_CODE >= KERNEL_VERSION(5,8,0)
		.flags		= PHY_POLL_CABLE_TEST,
#endif
		/* PHY_GBIT_FEATURES */
		.probe		= qca807x_probe,
		.config_init	= qca807x_config,
		.read_status	= qca807x_read_status,
		.config_intr	= qca807x_config_intr,
		.ack_interrupt	= qca807x_ack_intr,
		.soft_reset	= genphy_soft_reset,
		.get_tunable	= qca807x_get_tunable,
		.set_tunable	= qca807x_set_tunable,
#if LINUX_VERSION_CODE >= KERNEL_VERSION(5,8,0)
		.cable_test_start	= qca807x_cable_test_start,
		.cable_test_get_status	= qca807x_cable_test_get_status,
#endif
	},
	{
		PHY_ID_MATCH_EXACT(PHY_ID_QCA807X_PSGMII),
		.name           = "Qualcomm QCA807x PSGMII",
		.probe		= qca807x_psgmii_config,
	},
};
module_phy_driver(qca807x_drivers);

static struct mdio_device_id __maybe_unused qca807x_tbl[] = {
	{ PHY_ID_MATCH_EXACT(PHY_ID_QCA8072) },
	{ PHY_ID_MATCH_EXACT(PHY_ID_QCA8075) },
	{ PHY_ID_MATCH_MODEL(PHY_ID_QCA807X_PSGMII) },
	{ }
};

MODULE_AUTHOR("Robert Marko");
MODULE_DESCRIPTION("Qualcomm QCA807x PHY driver");
MODULE_DEVICE_TABLE(mdio, qca807x_tbl);
MODULE_LICENSE("GPL");