openwrt/target/linux/ath79/dts/ar9342_ubnt_nanostation-loco-m-xw.dts

// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
/dts-v1/;

#include "ar9342_ubnt_xw.dtsi"

/ {
	compatible = "ubnt,nanostation-loco-m-xw", "ubnt,xw", "qca,ar9342";
	model = "Ubiquiti Nanostation Loco M (XW)";
};

&mdio0 {
	status = "okay";

	phy-mask = <0x1>;

	phy1: ethernet-phy@1 {
		reg = <1>;
		phy-mode = "mii";
		reset-gpios = <&gpio 0 GPIO_ACTIVE_LOW>;
	};
};

&eth0 {
	status = "okay";

	phy-handle = <&phy1>;
};
ath79: add support for Ubiquiti NanoStation Loco M (XW) This commit adds support for the NanoStation Loco M2/M5 XW devices on the ath79 target (support was long ago available on ar71xx). Specifications: - AR9342 SoC @ 535 MHz - 64 MB RAM - 8 MB SPI flash - 1x 10/100 Mbps Ethernet, 24 Vdc PoE-in - AR8032 switch - 2T2R 5 GHz radio, 22 dBm - 13 dBi built-in antenna - POWER/LAN green LEDs - 4x RSSI LEDs (red, orange, green, green) - UART (115200 8N1) on PCB Flashing via TFTP: - Use a pointy tool (e.g., pen cap, paper clip) and keep the reset button on the device or on the PoE supply pressed - Power on the device via PoE (keep reset button pressed) - Keep pressing until LEDs flash alternatively LED1+LED3 => LED2+LED4 => LED1+LED3, etc. - Release reset button - The device starts a TFTP server at 192.168.1.20 - Set a static IP on the computer (e.g., 192.168.1.21/24) - Upload via tftp the factory image: $ tftp 192.168.1.20 tftp> bin tftp> trace tftp> put openwrt-ath79-generic-xxxxx-ubnt_nanostation-loco-m-xw-squashfs-factory.bin Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net> 2019-09-18 13:17:56 +00:00			`// SPDX-License-Identifier: GPL-2.0-or-later OR MIT`
			`/dts-v1/;`

			`#include "ar9342_ubnt_xw.dtsi"`

			`/ {`
			`compatible = "ubnt,nanostation-loco-m-xw", "ubnt,xw", "qca,ar9342";`
			`model = "Ubiquiti Nanostation Loco M (XW)";`
			`};`

			`&mdio0 {`
			`status = "okay";`

			`phy-mask = <0x1>;`

			`phy1: ethernet-phy@1 {`
			`reg = <1>;`
			`phy-mode = "mii";`
ath79: add missing reset-gpios for NanoStation Loco M (XW) When porting support from ar71xx to ath79, the reset-gpios option was missed. Due to a hardware bug, this would eventually leave the devices with RX-deaf Ethernet PHY. Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net> 2020-02-24 17:21:49 +00:00			`reset-gpios = <&gpio 0 GPIO_ACTIVE_LOW>;`
ath79: add support for Ubiquiti NanoStation Loco M (XW) This commit adds support for the NanoStation Loco M2/M5 XW devices on the ath79 target (support was long ago available on ar71xx). Specifications: - AR9342 SoC @ 535 MHz - 64 MB RAM - 8 MB SPI flash - 1x 10/100 Mbps Ethernet, 24 Vdc PoE-in - AR8032 switch - 2T2R 5 GHz radio, 22 dBm - 13 dBi built-in antenna - POWER/LAN green LEDs - 4x RSSI LEDs (red, orange, green, green) - UART (115200 8N1) on PCB Flashing via TFTP: - Use a pointy tool (e.g., pen cap, paper clip) and keep the reset button on the device or on the PoE supply pressed - Power on the device via PoE (keep reset button pressed) - Keep pressing until LEDs flash alternatively LED1+LED3 => LED2+LED4 => LED1+LED3, etc. - Release reset button - The device starts a TFTP server at 192.168.1.20 - Set a static IP on the computer (e.g., 192.168.1.21/24) - Upload via tftp the factory image: $ tftp 192.168.1.20 tftp> bin tftp> trace tftp> put openwrt-ath79-generic-xxxxx-ubnt_nanostation-loco-m-xw-squashfs-factory.bin Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net> 2019-09-18 13:17:56 +00:00			`};`
			`};`

			`&eth0 {`
			`status = "okay";`

			`phy-handle = <&phy1>;`
			`};`