openwrt/target/linux/ramips/dts/mt7621_xiaomi_mi-router-4a-3g-v2.dtsi

65 lines
1000 B
Plaintext
Raw Normal View History

ramips: add Xiaomi Mi Router 4A Gigabit explicitly This device has previously been supported by the image for Xiaomi Mi Router 3G v2. Since this is not obvious, the 4A is marketed as a new major revision and it also seems to have a different bootloader, this will be both more tidy and more helpful for the users. Apart from that, note that there also is a 100M version of the device that uses mt7628 platform, so a specifically named image will also prevent confusion in this area. Specifications: - SoC: MediaTek MT7621 - Flash: 16 MiB NOR SPI - RAM: 128 MiB DDR3 - Ethernet: 3x 10/100/1000 Mbps (switched, 2xLAN + WAN) - WIFI0: MT7603E 2.4GHz 802.11b/g/n - WIFI1: MT7612E 5GHz 802.11ac - Antennas: 4x external (2 per radio), non-detachable - LEDs: Programmable "power" LED (two-coloured, yellow/blue) Non-programmable "internet" LED (shows WAN activity) - Buttons: Reset Installation: Bootloader won't accept any serial input unless "boot_wait" u-boot environment variable is changed to "on". Vendor firmware won't accept any serial input until "uart_en" is set to "1". Using the https://github.com/acecilia/OpenWRTInvasion exploit you can gain access to shell to enable these options: To enable uart keyboard actions - 'nvram set uart_en=1' To make uboot delay boot work - 'nvram set boot_wait=on' Set boot delay to 5 - 'nvram set bootdelay=5' Then run 'nvram commit' to make the changes permanent. Once in the shell (following the OpenWRTInvasion instructions) you can then run the following to flash OpenWrt and then reboot: 'cd /tmp; curl https://downloads.openwrt.org/...-sysupgrade.bin --output firmware.bin; mtd -e OS1 -r write firmware.bin OS1' Suggested-by: David Bentham <db260179@gmail.com> Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-11-12 15:00:10 +00:00
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
ramips: mt7621: add support for Xiaomi Mi Router 4A Gigabit v2 Device is the same as Xiaomi Mi Router 4A Gigabit, except of: - 5G WiFi is MT7663 - addresses of leds, wifi and eth ports are slightly changed Specs: SoC: MT7621 CPU: 2 x 880 MHz ROM: 16 MB RAM: 128 MB WLAN: MT7603, MT7663 MAC addresses: WAN **** factory 0xe006 (label) LAN *:f7 factory 0xe000 2.4 GHz *:f8 factory 0x0000+0x4 (mtd-eeprom+0x4) 5 GHz *:f9 factory 0x8000+0x4 (mtd-eeprom+0x4) Installation: Factory firmware is based on a custom OpenWrt 17.x. Installation is the same as for Xiaomi Mi Router 4A Gigabit. Probably the easiest way to install is to use the script from this repository: https://github.com/acecilia/OpenWRTInvasion/pull/155 In a more advanced case, you can do everything yourself: - gain access to the device through one of the exploits described in the link above - upload sysupgrade image to /tmp - overwrite stock firmware: # mtd -e OS1 -r write /tmp/sysupgrade.bin OS1 Recovery: Recovery procedure is the same as for Xiaomi Mi Router 4A Gigabit. Possible options can be found here: https://openwrt.org/inbox/toh/xiaomi/xiaomi_mi_router_4a_gigabit_edition One of the ways is to use another router with OpenWrt: - connect both routers by their LAN ports - download stock firmware from [1] - place it inside /tmp/test.bin on the main router - configure PXE/TFTP on the main router - power off 4Av2, hold Reset button, power on - as soon as image download via TFTP starts, Reset can be released - blinking blue wan LED will indicate the end of the flashing process, now router can be rebooted [1] http://cdn.cnbj1.fds.api.mi-img.com/xiaoqiang/rom/r4av2/miwifi_r4av2_firmware_release_2.30.28.bin Signed-off-by: Dmitry Sokolov <e323w@proton.me>
2023-01-15 21:52:27 +00:00
#include "mt7621_xiaomi_mi-router-4a-common.dtsi"
ramips: add Xiaomi Mi Router 4A Gigabit explicitly This device has previously been supported by the image for Xiaomi Mi Router 3G v2. Since this is not obvious, the 4A is marketed as a new major revision and it also seems to have a different bootloader, this will be both more tidy and more helpful for the users. Apart from that, note that there also is a 100M version of the device that uses mt7628 platform, so a specifically named image will also prevent confusion in this area. Specifications: - SoC: MediaTek MT7621 - Flash: 16 MiB NOR SPI - RAM: 128 MiB DDR3 - Ethernet: 3x 10/100/1000 Mbps (switched, 2xLAN + WAN) - WIFI0: MT7603E 2.4GHz 802.11b/g/n - WIFI1: MT7612E 5GHz 802.11ac - Antennas: 4x external (2 per radio), non-detachable - LEDs: Programmable "power" LED (two-coloured, yellow/blue) Non-programmable "internet" LED (shows WAN activity) - Buttons: Reset Installation: Bootloader won't accept any serial input unless "boot_wait" u-boot environment variable is changed to "on". Vendor firmware won't accept any serial input until "uart_en" is set to "1". Using the https://github.com/acecilia/OpenWRTInvasion exploit you can gain access to shell to enable these options: To enable uart keyboard actions - 'nvram set uart_en=1' To make uboot delay boot work - 'nvram set boot_wait=on' Set boot delay to 5 - 'nvram set bootdelay=5' Then run 'nvram commit' to make the changes permanent. Once in the shell (following the OpenWRTInvasion instructions) you can then run the following to flash OpenWrt and then reboot: 'cd /tmp; curl https://downloads.openwrt.org/...-sysupgrade.bin --output firmware.bin; mtd -e OS1 -r write firmware.bin OS1' Suggested-by: David Bentham <db260179@gmail.com> Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-11-12 15:00:10 +00:00
/ {
aliases {
label-mac-device = &gmac1;
ramips: add Xiaomi Mi Router 4A Gigabit explicitly This device has previously been supported by the image for Xiaomi Mi Router 3G v2. Since this is not obvious, the 4A is marketed as a new major revision and it also seems to have a different bootloader, this will be both more tidy and more helpful for the users. Apart from that, note that there also is a 100M version of the device that uses mt7628 platform, so a specifically named image will also prevent confusion in this area. Specifications: - SoC: MediaTek MT7621 - Flash: 16 MiB NOR SPI - RAM: 128 MiB DDR3 - Ethernet: 3x 10/100/1000 Mbps (switched, 2xLAN + WAN) - WIFI0: MT7603E 2.4GHz 802.11b/g/n - WIFI1: MT7612E 5GHz 802.11ac - Antennas: 4x external (2 per radio), non-detachable - LEDs: Programmable "power" LED (two-coloured, yellow/blue) Non-programmable "internet" LED (shows WAN activity) - Buttons: Reset Installation: Bootloader won't accept any serial input unless "boot_wait" u-boot environment variable is changed to "on". Vendor firmware won't accept any serial input until "uart_en" is set to "1". Using the https://github.com/acecilia/OpenWRTInvasion exploit you can gain access to shell to enable these options: To enable uart keyboard actions - 'nvram set uart_en=1' To make uboot delay boot work - 'nvram set boot_wait=on' Set boot delay to 5 - 'nvram set bootdelay=5' Then run 'nvram commit' to make the changes permanent. Once in the shell (following the OpenWRTInvasion instructions) you can then run the following to flash OpenWrt and then reboot: 'cd /tmp; curl https://downloads.openwrt.org/...-sysupgrade.bin --output firmware.bin; mtd -e OS1 -r write firmware.bin OS1' Suggested-by: David Bentham <db260179@gmail.com> Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-11-12 15:00:10 +00:00
};
leds {
compatible = "gpio-leds";
led_status_blue: status_blue {
label = "blue:status";
gpios = <&gpio 8 GPIO_ACTIVE_LOW>;
};
led_status_yellow: status_yellow {
label = "yellow:status";
gpios = <&gpio 10 GPIO_ACTIVE_LOW>;
};
};
};
ramips: mt7621: add support for Xiaomi Mi Router 4A Gigabit v2 Device is the same as Xiaomi Mi Router 4A Gigabit, except of: - 5G WiFi is MT7663 - addresses of leds, wifi and eth ports are slightly changed Specs: SoC: MT7621 CPU: 2 x 880 MHz ROM: 16 MB RAM: 128 MB WLAN: MT7603, MT7663 MAC addresses: WAN **** factory 0xe006 (label) LAN *:f7 factory 0xe000 2.4 GHz *:f8 factory 0x0000+0x4 (mtd-eeprom+0x4) 5 GHz *:f9 factory 0x8000+0x4 (mtd-eeprom+0x4) Installation: Factory firmware is based on a custom OpenWrt 17.x. Installation is the same as for Xiaomi Mi Router 4A Gigabit. Probably the easiest way to install is to use the script from this repository: https://github.com/acecilia/OpenWRTInvasion/pull/155 In a more advanced case, you can do everything yourself: - gain access to the device through one of the exploits described in the link above - upload sysupgrade image to /tmp - overwrite stock firmware: # mtd -e OS1 -r write /tmp/sysupgrade.bin OS1 Recovery: Recovery procedure is the same as for Xiaomi Mi Router 4A Gigabit. Possible options can be found here: https://openwrt.org/inbox/toh/xiaomi/xiaomi_mi_router_4a_gigabit_edition One of the ways is to use another router with OpenWrt: - connect both routers by their LAN ports - download stock firmware from [1] - place it inside /tmp/test.bin on the main router - configure PXE/TFTP on the main router - power off 4Av2, hold Reset button, power on - as soon as image download via TFTP starts, Reset can be released - blinking blue wan LED will indicate the end of the flashing process, now router can be rebooted [1] http://cdn.cnbj1.fds.api.mi-img.com/xiaoqiang/rom/r4av2/miwifi_r4av2_firmware_release_2.30.28.bin Signed-off-by: Dmitry Sokolov <e323w@proton.me>
2023-01-15 21:52:27 +00:00
&wifi0 {
nvmem-cells = <&eeprom_factory_8000>;
nvmem-cell-names = "eeprom";
ramips: mt7621: add support for Xiaomi Mi Router 4A Gigabit v2 Device is the same as Xiaomi Mi Router 4A Gigabit, except of: - 5G WiFi is MT7663 - addresses of leds, wifi and eth ports are slightly changed Specs: SoC: MT7621 CPU: 2 x 880 MHz ROM: 16 MB RAM: 128 MB WLAN: MT7603, MT7663 MAC addresses: WAN **** factory 0xe006 (label) LAN *:f7 factory 0xe000 2.4 GHz *:f8 factory 0x0000+0x4 (mtd-eeprom+0x4) 5 GHz *:f9 factory 0x8000+0x4 (mtd-eeprom+0x4) Installation: Factory firmware is based on a custom OpenWrt 17.x. Installation is the same as for Xiaomi Mi Router 4A Gigabit. Probably the easiest way to install is to use the script from this repository: https://github.com/acecilia/OpenWRTInvasion/pull/155 In a more advanced case, you can do everything yourself: - gain access to the device through one of the exploits described in the link above - upload sysupgrade image to /tmp - overwrite stock firmware: # mtd -e OS1 -r write /tmp/sysupgrade.bin OS1 Recovery: Recovery procedure is the same as for Xiaomi Mi Router 4A Gigabit. Possible options can be found here: https://openwrt.org/inbox/toh/xiaomi/xiaomi_mi_router_4a_gigabit_edition One of the ways is to use another router with OpenWrt: - connect both routers by their LAN ports - download stock firmware from [1] - place it inside /tmp/test.bin on the main router - configure PXE/TFTP on the main router - power off 4Av2, hold Reset button, power on - as soon as image download via TFTP starts, Reset can be released - blinking blue wan LED will indicate the end of the flashing process, now router can be rebooted [1] http://cdn.cnbj1.fds.api.mi-img.com/xiaoqiang/rom/r4av2/miwifi_r4av2_firmware_release_2.30.28.bin Signed-off-by: Dmitry Sokolov <e323w@proton.me>
2023-01-15 21:52:27 +00:00
ieee80211-freq-limit = <5000000 6000000>;
ramips: add Xiaomi Mi Router 4A Gigabit explicitly This device has previously been supported by the image for Xiaomi Mi Router 3G v2. Since this is not obvious, the 4A is marketed as a new major revision and it also seems to have a different bootloader, this will be both more tidy and more helpful for the users. Apart from that, note that there also is a 100M version of the device that uses mt7628 platform, so a specifically named image will also prevent confusion in this area. Specifications: - SoC: MediaTek MT7621 - Flash: 16 MiB NOR SPI - RAM: 128 MiB DDR3 - Ethernet: 3x 10/100/1000 Mbps (switched, 2xLAN + WAN) - WIFI0: MT7603E 2.4GHz 802.11b/g/n - WIFI1: MT7612E 5GHz 802.11ac - Antennas: 4x external (2 per radio), non-detachable - LEDs: Programmable "power" LED (two-coloured, yellow/blue) Non-programmable "internet" LED (shows WAN activity) - Buttons: Reset Installation: Bootloader won't accept any serial input unless "boot_wait" u-boot environment variable is changed to "on". Vendor firmware won't accept any serial input until "uart_en" is set to "1". Using the https://github.com/acecilia/OpenWRTInvasion exploit you can gain access to shell to enable these options: To enable uart keyboard actions - 'nvram set uart_en=1' To make uboot delay boot work - 'nvram set boot_wait=on' Set boot delay to 5 - 'nvram set bootdelay=5' Then run 'nvram commit' to make the changes permanent. Once in the shell (following the OpenWRTInvasion instructions) you can then run the following to flash OpenWrt and then reboot: 'cd /tmp; curl https://downloads.openwrt.org/...-sysupgrade.bin --output firmware.bin; mtd -e OS1 -r write firmware.bin OS1' Suggested-by: David Bentham <db260179@gmail.com> Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-11-12 15:00:10 +00:00
};
ramips: mt7621: add support for Xiaomi Mi Router 4A Gigabit v2 Device is the same as Xiaomi Mi Router 4A Gigabit, except of: - 5G WiFi is MT7663 - addresses of leds, wifi and eth ports are slightly changed Specs: SoC: MT7621 CPU: 2 x 880 MHz ROM: 16 MB RAM: 128 MB WLAN: MT7603, MT7663 MAC addresses: WAN **** factory 0xe006 (label) LAN *:f7 factory 0xe000 2.4 GHz *:f8 factory 0x0000+0x4 (mtd-eeprom+0x4) 5 GHz *:f9 factory 0x8000+0x4 (mtd-eeprom+0x4) Installation: Factory firmware is based on a custom OpenWrt 17.x. Installation is the same as for Xiaomi Mi Router 4A Gigabit. Probably the easiest way to install is to use the script from this repository: https://github.com/acecilia/OpenWRTInvasion/pull/155 In a more advanced case, you can do everything yourself: - gain access to the device through one of the exploits described in the link above - upload sysupgrade image to /tmp - overwrite stock firmware: # mtd -e OS1 -r write /tmp/sysupgrade.bin OS1 Recovery: Recovery procedure is the same as for Xiaomi Mi Router 4A Gigabit. Possible options can be found here: https://openwrt.org/inbox/toh/xiaomi/xiaomi_mi_router_4a_gigabit_edition One of the ways is to use another router with OpenWrt: - connect both routers by their LAN ports - download stock firmware from [1] - place it inside /tmp/test.bin on the main router - configure PXE/TFTP on the main router - power off 4Av2, hold Reset button, power on - as soon as image download via TFTP starts, Reset can be released - blinking blue wan LED will indicate the end of the flashing process, now router can be rebooted [1] http://cdn.cnbj1.fds.api.mi-img.com/xiaoqiang/rom/r4av2/miwifi_r4av2_firmware_release_2.30.28.bin Signed-off-by: Dmitry Sokolov <e323w@proton.me>
2023-01-15 21:52:27 +00:00
&wifi1 {
nvmem-cells = <&eeprom_factory_0>;
nvmem-cell-names = "eeprom";
ramips: mt7621: add support for Xiaomi Mi Router 4A Gigabit v2 Device is the same as Xiaomi Mi Router 4A Gigabit, except of: - 5G WiFi is MT7663 - addresses of leds, wifi and eth ports are slightly changed Specs: SoC: MT7621 CPU: 2 x 880 MHz ROM: 16 MB RAM: 128 MB WLAN: MT7603, MT7663 MAC addresses: WAN **** factory 0xe006 (label) LAN *:f7 factory 0xe000 2.4 GHz *:f8 factory 0x0000+0x4 (mtd-eeprom+0x4) 5 GHz *:f9 factory 0x8000+0x4 (mtd-eeprom+0x4) Installation: Factory firmware is based on a custom OpenWrt 17.x. Installation is the same as for Xiaomi Mi Router 4A Gigabit. Probably the easiest way to install is to use the script from this repository: https://github.com/acecilia/OpenWRTInvasion/pull/155 In a more advanced case, you can do everything yourself: - gain access to the device through one of the exploits described in the link above - upload sysupgrade image to /tmp - overwrite stock firmware: # mtd -e OS1 -r write /tmp/sysupgrade.bin OS1 Recovery: Recovery procedure is the same as for Xiaomi Mi Router 4A Gigabit. Possible options can be found here: https://openwrt.org/inbox/toh/xiaomi/xiaomi_mi_router_4a_gigabit_edition One of the ways is to use another router with OpenWrt: - connect both routers by their LAN ports - download stock firmware from [1] - place it inside /tmp/test.bin on the main router - configure PXE/TFTP on the main router - power off 4Av2, hold Reset button, power on - as soon as image download via TFTP starts, Reset can be released - blinking blue wan LED will indicate the end of the flashing process, now router can be rebooted [1] http://cdn.cnbj1.fds.api.mi-img.com/xiaoqiang/rom/r4av2/miwifi_r4av2_firmware_release_2.30.28.bin Signed-off-by: Dmitry Sokolov <e323w@proton.me>
2023-01-15 21:52:27 +00:00
ieee80211-freq-limit = <2400000 2500000>;
ramips: add Xiaomi Mi Router 4A Gigabit explicitly This device has previously been supported by the image for Xiaomi Mi Router 3G v2. Since this is not obvious, the 4A is marketed as a new major revision and it also seems to have a different bootloader, this will be both more tidy and more helpful for the users. Apart from that, note that there also is a 100M version of the device that uses mt7628 platform, so a specifically named image will also prevent confusion in this area. Specifications: - SoC: MediaTek MT7621 - Flash: 16 MiB NOR SPI - RAM: 128 MiB DDR3 - Ethernet: 3x 10/100/1000 Mbps (switched, 2xLAN + WAN) - WIFI0: MT7603E 2.4GHz 802.11b/g/n - WIFI1: MT7612E 5GHz 802.11ac - Antennas: 4x external (2 per radio), non-detachable - LEDs: Programmable "power" LED (two-coloured, yellow/blue) Non-programmable "internet" LED (shows WAN activity) - Buttons: Reset Installation: Bootloader won't accept any serial input unless "boot_wait" u-boot environment variable is changed to "on". Vendor firmware won't accept any serial input until "uart_en" is set to "1". Using the https://github.com/acecilia/OpenWRTInvasion exploit you can gain access to shell to enable these options: To enable uart keyboard actions - 'nvram set uart_en=1' To make uboot delay boot work - 'nvram set boot_wait=on' Set boot delay to 5 - 'nvram set bootdelay=5' Then run 'nvram commit' to make the changes permanent. Once in the shell (following the OpenWRTInvasion instructions) you can then run the following to flash OpenWrt and then reboot: 'cd /tmp; curl https://downloads.openwrt.org/...-sysupgrade.bin --output firmware.bin; mtd -e OS1 -r write firmware.bin OS1' Suggested-by: David Bentham <db260179@gmail.com> Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-11-12 15:00:10 +00:00
};
&gmac1 {
status = "okay";
label = "wan";
phy-handle = <&ethphy4>;
nvmem-cells = <&macaddr_factory_e006>;
nvmem-cell-names = "mac-address";
};
&mdio {
ethphy4: ethernet-phy@4 {
reg = <4>;
};
};
ramips: add Xiaomi Mi Router 4A Gigabit explicitly This device has previously been supported by the image for Xiaomi Mi Router 3G v2. Since this is not obvious, the 4A is marketed as a new major revision and it also seems to have a different bootloader, this will be both more tidy and more helpful for the users. Apart from that, note that there also is a 100M version of the device that uses mt7628 platform, so a specifically named image will also prevent confusion in this area. Specifications: - SoC: MediaTek MT7621 - Flash: 16 MiB NOR SPI - RAM: 128 MiB DDR3 - Ethernet: 3x 10/100/1000 Mbps (switched, 2xLAN + WAN) - WIFI0: MT7603E 2.4GHz 802.11b/g/n - WIFI1: MT7612E 5GHz 802.11ac - Antennas: 4x external (2 per radio), non-detachable - LEDs: Programmable "power" LED (two-coloured, yellow/blue) Non-programmable "internet" LED (shows WAN activity) - Buttons: Reset Installation: Bootloader won't accept any serial input unless "boot_wait" u-boot environment variable is changed to "on". Vendor firmware won't accept any serial input until "uart_en" is set to "1". Using the https://github.com/acecilia/OpenWRTInvasion exploit you can gain access to shell to enable these options: To enable uart keyboard actions - 'nvram set uart_en=1' To make uboot delay boot work - 'nvram set boot_wait=on' Set boot delay to 5 - 'nvram set bootdelay=5' Then run 'nvram commit' to make the changes permanent. Once in the shell (following the OpenWRTInvasion instructions) you can then run the following to flash OpenWrt and then reboot: 'cd /tmp; curl https://downloads.openwrt.org/...-sysupgrade.bin --output firmware.bin; mtd -e OS1 -r write firmware.bin OS1' Suggested-by: David Bentham <db260179@gmail.com> Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-11-12 15:00:10 +00:00
&switch0 {
ports {
port@2 {
status = "okay";
label = "lan2";
};
port@3 {
status = "okay";
label = "lan1";
};
};
};