openwrt/target/linux/ramips/dts/mt7621_dlink_dir-867-a1.dts

// SPDX-License-Identifier: GPL-2.0-or-later OR MIT

#include "mt7621_dlink_dir-8xx.dtsi"
#include "mt7621_dlink_flash-16m-a1.dtsi"

/ {
	compatible = "dlink,dir-867-a1", "mediatek,mt7621-soc";
	model = "D-Link DIR-867 A1";

	aliases {
		label-mac-device = &gmac0;
	};
};

&gmac0 {
	nvmem-cells = <&macaddr_factory_e000>;
	nvmem-cell-names = "mac-address";
};

&gmac1 {
	nvmem-cells = <&macaddr_factory_e006>;
	nvmem-cell-names = "mac-address";
};
ramips: add support for D-Link DIR-867/DIR-882 A1 This patch adds support for D-Link DIR-867 A1 and D-Link DIR-882 A1. Given the similarity of these devices, this patch also introduces a common DTS shared between DIR-867 A1, DIR-878 A1 and DIR-882 A1. Specifications: * Board: AP-MTKH7-0002 * SoC: MediaTek MT7621AT * RAM: 128 MB (DDR3) * Flash: 16 MB (SPI NOR) * WiFi: MediaTek MT7615N (x2) * Switch: 1 WAN, 4 LAN (Gigabit) * Ports: 1 USB 2.0, 1 USB 3.0 * Buttons: Reset, WiFi Toggle, WPS * LEDs: Power (green/orange), Internet (green/orange), WiFi 2.4G (green), WiFi 5G (green), USB 2.0 (green), USB 3.0 (green) Notes: * WiFi 2.4G and WiFi 5G LEDs are wired directly to the wireless chips * DIR-867 wireless chips are limited to 3x3 streams at hardware level * USB ports and related LEDs available only on DIR-882 Serial port: * Parameters: 57600, 8N1 * Location: J1 header (close to the Reset, WiFi and WPS buttons) * Pinout: 1 - VCC 2 - RXD 3 - TXD 4 - GND Installation: * D-Link Recovery GUI: power down the router, press and hold the reset button, then re-plug it. Keep the reset button pressed until the power LED starts flashing orange, manually assign a static IP address under the 192.168.0.xxx subnet (e.g. 192.168.0.2) and go to http://192.168.0.1 * Some modern browsers may have problems flashing via the Recovery GUI, if that occurs consider uploading the firmware through cURL: curl -v -i -F "firmware=@file.bin" 192.168.0.1 Signed-off-by: Mateus B. Cassiano <mbc07@live.com> [move DEVICE_VARIANT to individual definitions] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> 2020-07-15 21:45:39 +00:00			`// SPDX-License-Identifier: GPL-2.0-or-later OR MIT`

ramips: reorganize DTSI files for D-Link DIR-8xx * Remove micro-DTSI mt7621_dlink_dir-882-x1.dtsi to ease reading config without too much inheritance * Use "separate" partitioning DTSIs so we can use the partitioning without a complete match on the other settings (i.e. without the former parent DTSI) * Rename files to express the new organization Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> 2021-06-20 15:11:09 +00:00			`#include "mt7621_dlink_dir-8xx.dtsi"`
			`#include "mt7621_dlink_flash-16m-a1.dtsi"`
ramips: add support for D-Link DIR-867/DIR-882 A1 This patch adds support for D-Link DIR-867 A1 and D-Link DIR-882 A1. Given the similarity of these devices, this patch also introduces a common DTS shared between DIR-867 A1, DIR-878 A1 and DIR-882 A1. Specifications: * Board: AP-MTKH7-0002 * SoC: MediaTek MT7621AT * RAM: 128 MB (DDR3) * Flash: 16 MB (SPI NOR) * WiFi: MediaTek MT7615N (x2) * Switch: 1 WAN, 4 LAN (Gigabit) * Ports: 1 USB 2.0, 1 USB 3.0 * Buttons: Reset, WiFi Toggle, WPS * LEDs: Power (green/orange), Internet (green/orange), WiFi 2.4G (green), WiFi 5G (green), USB 2.0 (green), USB 3.0 (green) Notes: * WiFi 2.4G and WiFi 5G LEDs are wired directly to the wireless chips * DIR-867 wireless chips are limited to 3x3 streams at hardware level * USB ports and related LEDs available only on DIR-882 Serial port: * Parameters: 57600, 8N1 * Location: J1 header (close to the Reset, WiFi and WPS buttons) * Pinout: 1 - VCC 2 - RXD 3 - TXD 4 - GND Installation: * D-Link Recovery GUI: power down the router, press and hold the reset button, then re-plug it. Keep the reset button pressed until the power LED starts flashing orange, manually assign a static IP address under the 192.168.0.xxx subnet (e.g. 192.168.0.2) and go to http://192.168.0.1 * Some modern browsers may have problems flashing via the Recovery GUI, if that occurs consider uploading the firmware through cURL: curl -v -i -F "firmware=@file.bin" 192.168.0.1 Signed-off-by: Mateus B. Cassiano <mbc07@live.com> [move DEVICE_VARIANT to individual definitions] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> 2020-07-15 21:45:39 +00:00
			`/ {`
			`compatible = "dlink,dir-867-a1", "mediatek,mt7621-soc";`
			`model = "D-Link DIR-867 A1";`
ramips: convert mtd-mac-address to nvmem for D-Link DIR-8xx Convert this series by moving the definitions to the individual devices. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> 2021-08-18 23:16:39 +00:00
			`aliases {`
			`label-mac-device = &gmac0;`
			`};`
			`};`

			`&gmac0 {`
			`nvmem-cells = <&macaddr_factory_e000>;`
			`nvmem-cell-names = "mac-address";`
			`};`

ramips: mt7621-dts: mux phy0/4 to gmac1 Mux the MT7530 switch's phy0/4 to the SoC's gmac1 on devices where RGMII2 pins are available. This achieves 2 Gbps total bandwidth to the CPU using the second RGMII. The ports called "wan" are muxed where possible. On a minority of devices, this is not possible. Those cases: mt7621_ampedwireless_ally-r1900k.dts: lan3 mt7621_ubnt_edgerouter-x.dts: eth0 mt7621_gnubee_gb-pc1.dts: ethblue mt7621_linksys_re6500.dts: lan1 mt7621_netgear_wac104.dts: lan4 mt7621_tplink_eap235-wall-v1.dts: lan0 mt7621_tplink_eap615-wall-v1.dts: lan0 mt7621_ubnt_usw-flex.dts: lan1 The "wan" port is just what the vendor designated on the board/plastic chasis of the device. On a technical level, there is no difference between a lan and wan port on MT7621AT, MT7621DAT and MT7621ST SoCs. Prefer connecting to WAN via the port described above for these devices to benefit the feature brought with this patch. mt7621_d-team_newifi-d2.dts cannot benefit this feature, although it looks like it should, because the rgmii2 pins are wired to unused components. Tested on a range of devices documented on the GitHub PR. Link: https://github.com/openwrt/openwrt/pull/10238 Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com> 2022-07-05 22:20:32 +00:00			`&gmac1 {`
ramips: convert mtd-mac-address to nvmem for D-Link DIR-8xx Convert this series by moving the definitions to the individual devices. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> 2021-08-18 23:16:39 +00:00			`nvmem-cells = <&macaddr_factory_e006>;`
			`nvmem-cell-names = "mac-address";`
			`};`