openwrt/target/linux/ramips/dts/mt7628an_unielec_u7628-01-16m.dts

70 lines
1.3 KiB
Plaintext
Raw Normal View History

// SPDX-License-Identifier: BSD-3-Clause
ramips: add support for UniElec U7628-01 UniElec U7628-01 is a router platform board based on MediaTek MT7628AN. The device has the following specifications: - MT7628AN (580MHz) - 64/128/256 MB of RAM (DDR2) - 8/16 MB of flash (SPI NOR) - 5x 10/100 Mbps Ethernet (MT7628 built-in switch) - 1x 2T2R 2.4 GHz Wi-Fi (MT7628) - 1x miniPCIe slot (with PCIe and USB 2.0 buses) - 1x miniSIM slot - 1x microSD slot - 1x USB 2.0 port - 7x single-color LEDs (GPIO-controlled) - 1x bi-color LED (green GPIO-controlled, red -> LED_WLAN# in miniPCIe) - 1x reset button - 1x UART header (4-pins) - 1x SDXC/GPIO header (10-pins, connected with microSD slot) - 1x DC jack for main power (12 V) The following has been tested and is working: - Ethernet switch - miniPCIe slot (tested with modem and Wi-Fi card) - miniSIM slot - sysupgrade - reset button - USB 2.0 port* Due to a missing driver (MMC over GPIO) this is not supported: - microSD card reader * Warning: USB buses in miniPCIe and regular A-type socket are connected together, without any proper analog switch or USB HUB. Installation: This board might come with a different firmware versions (MediaTek SDK, PandoraBox, Padavan, etc.). If your board comes with PandoraBox, you can install LEDE using sysupgrade. Just SSH to the router and perform forced sysupgrade (due to a board name mismatch). The default IP of this board should be: 192.168.1.1 and username/password: root/admin. In case of a different firmware, you can use web based recovery described below. Use the following command to perform the sysupgrade (for the 128MB RAM/16MB flash version): sysupgrade -n -F lede-ramips-mt76x8-u7628-01-128M-16M-squashfs-sysupgrade.bin Recovery: This board contains a Chinese, closed-source bootloader called Breed (Boot and Recovery Environment for Embedded Devices). Breed supports web recovery and to enter it, you keep the reset button pressed for around 5 seconds during boot. Your machine will be assigned an IP through DHCP and the router will use IP address 192.168.1.1. The recovery website is in Chinese, but is easy to use. Click on the second item in the list to access the recovery page, then the second item on the next page is where you select the firmware. In order to start the recovery, you click the button at the bottom. SDXC/GPIO header (J3): 1. SDXC_D3 / I2C_SCLK 2. SDXC_D2 / I2C_SD 3. SDXC_D1 / I2S_DI 4. SDXC_D0 / I2S_WS 5. SDXC_CMD / I2S_CLK 6. SDXC_CLK / GPIO0 7. SDXC_CD / UART_RXD1 8. UART_TXD1 9. 3V3 10. GND Other notes: 1. The board is available with different amounts of RAM and flash. We have only added support for the 128/16 MB configuration, as that seems to be the default. However, all the required infrastructure is in place for making support for the other configurations easy. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com> Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
2017-11-03 20:12:49 +00:00
/*
* Copyright(c) 2017 Kristian Evensen <kristian.evensen@gmail.com>.
* Copyright(c) 2017 Piotr Dymacz <pepe2k@gmail.com>.
* All rights reserved.
*/
#include "mt7628an_unielec_u7628-01.dtsi"
ramips: add support for UniElec U7628-01 UniElec U7628-01 is a router platform board based on MediaTek MT7628AN. The device has the following specifications: - MT7628AN (580MHz) - 64/128/256 MB of RAM (DDR2) - 8/16 MB of flash (SPI NOR) - 5x 10/100 Mbps Ethernet (MT7628 built-in switch) - 1x 2T2R 2.4 GHz Wi-Fi (MT7628) - 1x miniPCIe slot (with PCIe and USB 2.0 buses) - 1x miniSIM slot - 1x microSD slot - 1x USB 2.0 port - 7x single-color LEDs (GPIO-controlled) - 1x bi-color LED (green GPIO-controlled, red -> LED_WLAN# in miniPCIe) - 1x reset button - 1x UART header (4-pins) - 1x SDXC/GPIO header (10-pins, connected with microSD slot) - 1x DC jack for main power (12 V) The following has been tested and is working: - Ethernet switch - miniPCIe slot (tested with modem and Wi-Fi card) - miniSIM slot - sysupgrade - reset button - USB 2.0 port* Due to a missing driver (MMC over GPIO) this is not supported: - microSD card reader * Warning: USB buses in miniPCIe and regular A-type socket are connected together, without any proper analog switch or USB HUB. Installation: This board might come with a different firmware versions (MediaTek SDK, PandoraBox, Padavan, etc.). If your board comes with PandoraBox, you can install LEDE using sysupgrade. Just SSH to the router and perform forced sysupgrade (due to a board name mismatch). The default IP of this board should be: 192.168.1.1 and username/password: root/admin. In case of a different firmware, you can use web based recovery described below. Use the following command to perform the sysupgrade (for the 128MB RAM/16MB flash version): sysupgrade -n -F lede-ramips-mt76x8-u7628-01-128M-16M-squashfs-sysupgrade.bin Recovery: This board contains a Chinese, closed-source bootloader called Breed (Boot and Recovery Environment for Embedded Devices). Breed supports web recovery and to enter it, you keep the reset button pressed for around 5 seconds during boot. Your machine will be assigned an IP through DHCP and the router will use IP address 192.168.1.1. The recovery website is in Chinese, but is easy to use. Click on the second item in the list to access the recovery page, then the second item on the next page is where you select the firmware. In order to start the recovery, you click the button at the bottom. SDXC/GPIO header (J3): 1. SDXC_D3 / I2C_SCLK 2. SDXC_D2 / I2C_SD 3. SDXC_D1 / I2S_DI 4. SDXC_D0 / I2S_WS 5. SDXC_CMD / I2S_CLK 6. SDXC_CLK / GPIO0 7. SDXC_CD / UART_RXD1 8. UART_TXD1 9. 3V3 10. GND Other notes: 1. The board is available with different amounts of RAM and flash. We have only added support for the 128/16 MB configuration, as that seems to be the default. However, all the required infrastructure is in place for making support for the other configurations easy. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com> Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
2017-11-03 20:12:49 +00:00
/ {
compatible = "unielec,u7628-01-16m", "unielec,u7628-01", "mediatek,mt7628an-soc";
model = "UniElec U7628-01 (16M flash)";
ramips: add support for UniElec U7628-01 UniElec U7628-01 is a router platform board based on MediaTek MT7628AN. The device has the following specifications: - MT7628AN (580MHz) - 64/128/256 MB of RAM (DDR2) - 8/16 MB of flash (SPI NOR) - 5x 10/100 Mbps Ethernet (MT7628 built-in switch) - 1x 2T2R 2.4 GHz Wi-Fi (MT7628) - 1x miniPCIe slot (with PCIe and USB 2.0 buses) - 1x miniSIM slot - 1x microSD slot - 1x USB 2.0 port - 7x single-color LEDs (GPIO-controlled) - 1x bi-color LED (green GPIO-controlled, red -> LED_WLAN# in miniPCIe) - 1x reset button - 1x UART header (4-pins) - 1x SDXC/GPIO header (10-pins, connected with microSD slot) - 1x DC jack for main power (12 V) The following has been tested and is working: - Ethernet switch - miniPCIe slot (tested with modem and Wi-Fi card) - miniSIM slot - sysupgrade - reset button - USB 2.0 port* Due to a missing driver (MMC over GPIO) this is not supported: - microSD card reader * Warning: USB buses in miniPCIe and regular A-type socket are connected together, without any proper analog switch or USB HUB. Installation: This board might come with a different firmware versions (MediaTek SDK, PandoraBox, Padavan, etc.). If your board comes with PandoraBox, you can install LEDE using sysupgrade. Just SSH to the router and perform forced sysupgrade (due to a board name mismatch). The default IP of this board should be: 192.168.1.1 and username/password: root/admin. In case of a different firmware, you can use web based recovery described below. Use the following command to perform the sysupgrade (for the 128MB RAM/16MB flash version): sysupgrade -n -F lede-ramips-mt76x8-u7628-01-128M-16M-squashfs-sysupgrade.bin Recovery: This board contains a Chinese, closed-source bootloader called Breed (Boot and Recovery Environment for Embedded Devices). Breed supports web recovery and to enter it, you keep the reset button pressed for around 5 seconds during boot. Your machine will be assigned an IP through DHCP and the router will use IP address 192.168.1.1. The recovery website is in Chinese, but is easy to use. Click on the second item in the list to access the recovery page, then the second item on the next page is where you select the firmware. In order to start the recovery, you click the button at the bottom. SDXC/GPIO header (J3): 1. SDXC_D3 / I2C_SCLK 2. SDXC_D2 / I2C_SD 3. SDXC_D1 / I2S_DI 4. SDXC_D0 / I2S_WS 5. SDXC_CMD / I2S_CLK 6. SDXC_CLK / GPIO0 7. SDXC_CD / UART_RXD1 8. UART_TXD1 9. 3V3 10. GND Other notes: 1. The board is available with different amounts of RAM and flash. We have only added support for the 128/16 MB configuration, as that seems to be the default. However, all the required infrastructure is in place for making support for the other configurations easy. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com> Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
2017-11-03 20:12:49 +00:00
};
&spi0 {
status = "okay";
flash@0 {
ramips: add support for UniElec U7628-01 UniElec U7628-01 is a router platform board based on MediaTek MT7628AN. The device has the following specifications: - MT7628AN (580MHz) - 64/128/256 MB of RAM (DDR2) - 8/16 MB of flash (SPI NOR) - 5x 10/100 Mbps Ethernet (MT7628 built-in switch) - 1x 2T2R 2.4 GHz Wi-Fi (MT7628) - 1x miniPCIe slot (with PCIe and USB 2.0 buses) - 1x miniSIM slot - 1x microSD slot - 1x USB 2.0 port - 7x single-color LEDs (GPIO-controlled) - 1x bi-color LED (green GPIO-controlled, red -> LED_WLAN# in miniPCIe) - 1x reset button - 1x UART header (4-pins) - 1x SDXC/GPIO header (10-pins, connected with microSD slot) - 1x DC jack for main power (12 V) The following has been tested and is working: - Ethernet switch - miniPCIe slot (tested with modem and Wi-Fi card) - miniSIM slot - sysupgrade - reset button - USB 2.0 port* Due to a missing driver (MMC over GPIO) this is not supported: - microSD card reader * Warning: USB buses in miniPCIe and regular A-type socket are connected together, without any proper analog switch or USB HUB. Installation: This board might come with a different firmware versions (MediaTek SDK, PandoraBox, Padavan, etc.). If your board comes with PandoraBox, you can install LEDE using sysupgrade. Just SSH to the router and perform forced sysupgrade (due to a board name mismatch). The default IP of this board should be: 192.168.1.1 and username/password: root/admin. In case of a different firmware, you can use web based recovery described below. Use the following command to perform the sysupgrade (for the 128MB RAM/16MB flash version): sysupgrade -n -F lede-ramips-mt76x8-u7628-01-128M-16M-squashfs-sysupgrade.bin Recovery: This board contains a Chinese, closed-source bootloader called Breed (Boot and Recovery Environment for Embedded Devices). Breed supports web recovery and to enter it, you keep the reset button pressed for around 5 seconds during boot. Your machine will be assigned an IP through DHCP and the router will use IP address 192.168.1.1. The recovery website is in Chinese, but is easy to use. Click on the second item in the list to access the recovery page, then the second item on the next page is where you select the firmware. In order to start the recovery, you click the button at the bottom. SDXC/GPIO header (J3): 1. SDXC_D3 / I2C_SCLK 2. SDXC_D2 / I2C_SD 3. SDXC_D1 / I2S_DI 4. SDXC_D0 / I2S_WS 5. SDXC_CMD / I2S_CLK 6. SDXC_CLK / GPIO0 7. SDXC_CD / UART_RXD1 8. UART_TXD1 9. 3V3 10. GND Other notes: 1. The board is available with different amounts of RAM and flash. We have only added support for the 128/16 MB configuration, as that seems to be the default. However, all the required infrastructure is in place for making support for the other configurations easy. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com> Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
2017-11-03 20:12:49 +00:00
compatible = "jedec,spi-nor";
reg = <0>;
spi-max-frequency = <12000000>;
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
ramips: add support for UniElec U7628-01 UniElec U7628-01 is a router platform board based on MediaTek MT7628AN. The device has the following specifications: - MT7628AN (580MHz) - 64/128/256 MB of RAM (DDR2) - 8/16 MB of flash (SPI NOR) - 5x 10/100 Mbps Ethernet (MT7628 built-in switch) - 1x 2T2R 2.4 GHz Wi-Fi (MT7628) - 1x miniPCIe slot (with PCIe and USB 2.0 buses) - 1x miniSIM slot - 1x microSD slot - 1x USB 2.0 port - 7x single-color LEDs (GPIO-controlled) - 1x bi-color LED (green GPIO-controlled, red -> LED_WLAN# in miniPCIe) - 1x reset button - 1x UART header (4-pins) - 1x SDXC/GPIO header (10-pins, connected with microSD slot) - 1x DC jack for main power (12 V) The following has been tested and is working: - Ethernet switch - miniPCIe slot (tested with modem and Wi-Fi card) - miniSIM slot - sysupgrade - reset button - USB 2.0 port* Due to a missing driver (MMC over GPIO) this is not supported: - microSD card reader * Warning: USB buses in miniPCIe and regular A-type socket are connected together, without any proper analog switch or USB HUB. Installation: This board might come with a different firmware versions (MediaTek SDK, PandoraBox, Padavan, etc.). If your board comes with PandoraBox, you can install LEDE using sysupgrade. Just SSH to the router and perform forced sysupgrade (due to a board name mismatch). The default IP of this board should be: 192.168.1.1 and username/password: root/admin. In case of a different firmware, you can use web based recovery described below. Use the following command to perform the sysupgrade (for the 128MB RAM/16MB flash version): sysupgrade -n -F lede-ramips-mt76x8-u7628-01-128M-16M-squashfs-sysupgrade.bin Recovery: This board contains a Chinese, closed-source bootloader called Breed (Boot and Recovery Environment for Embedded Devices). Breed supports web recovery and to enter it, you keep the reset button pressed for around 5 seconds during boot. Your machine will be assigned an IP through DHCP and the router will use IP address 192.168.1.1. The recovery website is in Chinese, but is easy to use. Click on the second item in the list to access the recovery page, then the second item on the next page is where you select the firmware. In order to start the recovery, you click the button at the bottom. SDXC/GPIO header (J3): 1. SDXC_D3 / I2C_SCLK 2. SDXC_D2 / I2C_SD 3. SDXC_D1 / I2S_DI 4. SDXC_D0 / I2S_WS 5. SDXC_CMD / I2S_CLK 6. SDXC_CLK / GPIO0 7. SDXC_CD / UART_RXD1 8. UART_TXD1 9. 3V3 10. GND Other notes: 1. The board is available with different amounts of RAM and flash. We have only added support for the 128/16 MB configuration, as that seems to be the default. However, all the required infrastructure is in place for making support for the other configurations easy. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com> Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
2017-11-03 20:12:49 +00:00
partition@0 {
label = "bootloader";
reg = <0x0 0x30000>;
read-only;
};
ramips: add support for UniElec U7628-01 UniElec U7628-01 is a router platform board based on MediaTek MT7628AN. The device has the following specifications: - MT7628AN (580MHz) - 64/128/256 MB of RAM (DDR2) - 8/16 MB of flash (SPI NOR) - 5x 10/100 Mbps Ethernet (MT7628 built-in switch) - 1x 2T2R 2.4 GHz Wi-Fi (MT7628) - 1x miniPCIe slot (with PCIe and USB 2.0 buses) - 1x miniSIM slot - 1x microSD slot - 1x USB 2.0 port - 7x single-color LEDs (GPIO-controlled) - 1x bi-color LED (green GPIO-controlled, red -> LED_WLAN# in miniPCIe) - 1x reset button - 1x UART header (4-pins) - 1x SDXC/GPIO header (10-pins, connected with microSD slot) - 1x DC jack for main power (12 V) The following has been tested and is working: - Ethernet switch - miniPCIe slot (tested with modem and Wi-Fi card) - miniSIM slot - sysupgrade - reset button - USB 2.0 port* Due to a missing driver (MMC over GPIO) this is not supported: - microSD card reader * Warning: USB buses in miniPCIe and regular A-type socket are connected together, without any proper analog switch or USB HUB. Installation: This board might come with a different firmware versions (MediaTek SDK, PandoraBox, Padavan, etc.). If your board comes with PandoraBox, you can install LEDE using sysupgrade. Just SSH to the router and perform forced sysupgrade (due to a board name mismatch). The default IP of this board should be: 192.168.1.1 and username/password: root/admin. In case of a different firmware, you can use web based recovery described below. Use the following command to perform the sysupgrade (for the 128MB RAM/16MB flash version): sysupgrade -n -F lede-ramips-mt76x8-u7628-01-128M-16M-squashfs-sysupgrade.bin Recovery: This board contains a Chinese, closed-source bootloader called Breed (Boot and Recovery Environment for Embedded Devices). Breed supports web recovery and to enter it, you keep the reset button pressed for around 5 seconds during boot. Your machine will be assigned an IP through DHCP and the router will use IP address 192.168.1.1. The recovery website is in Chinese, but is easy to use. Click on the second item in the list to access the recovery page, then the second item on the next page is where you select the firmware. In order to start the recovery, you click the button at the bottom. SDXC/GPIO header (J3): 1. SDXC_D3 / I2C_SCLK 2. SDXC_D2 / I2C_SD 3. SDXC_D1 / I2S_DI 4. SDXC_D0 / I2S_WS 5. SDXC_CMD / I2S_CLK 6. SDXC_CLK / GPIO0 7. SDXC_CD / UART_RXD1 8. UART_TXD1 9. 3V3 10. GND Other notes: 1. The board is available with different amounts of RAM and flash. We have only added support for the 128/16 MB configuration, as that seems to be the default. However, all the required infrastructure is in place for making support for the other configurations easy. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com> Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
2017-11-03 20:12:49 +00:00
partition@30000 {
label = "config";
reg = <0x30000 0x10000>;
read-only;
};
factory: partition@40000 {
compatible = "nvmem-cells";
label = "factory";
reg = <0x40000 0x10000>;
#address-cells = <1>;
#size-cells = <1>;
read-only;
eeprom_factory_0: eeprom@0 {
reg = <0x0 0x400>;
};
macaddr_factory_28: macaddr@28 {
reg = <0x28 0x6>;
};
};
ramips: add support for UniElec U7628-01 UniElec U7628-01 is a router platform board based on MediaTek MT7628AN. The device has the following specifications: - MT7628AN (580MHz) - 64/128/256 MB of RAM (DDR2) - 8/16 MB of flash (SPI NOR) - 5x 10/100 Mbps Ethernet (MT7628 built-in switch) - 1x 2T2R 2.4 GHz Wi-Fi (MT7628) - 1x miniPCIe slot (with PCIe and USB 2.0 buses) - 1x miniSIM slot - 1x microSD slot - 1x USB 2.0 port - 7x single-color LEDs (GPIO-controlled) - 1x bi-color LED (green GPIO-controlled, red -> LED_WLAN# in miniPCIe) - 1x reset button - 1x UART header (4-pins) - 1x SDXC/GPIO header (10-pins, connected with microSD slot) - 1x DC jack for main power (12 V) The following has been tested and is working: - Ethernet switch - miniPCIe slot (tested with modem and Wi-Fi card) - miniSIM slot - sysupgrade - reset button - USB 2.0 port* Due to a missing driver (MMC over GPIO) this is not supported: - microSD card reader * Warning: USB buses in miniPCIe and regular A-type socket are connected together, without any proper analog switch or USB HUB. Installation: This board might come with a different firmware versions (MediaTek SDK, PandoraBox, Padavan, etc.). If your board comes with PandoraBox, you can install LEDE using sysupgrade. Just SSH to the router and perform forced sysupgrade (due to a board name mismatch). The default IP of this board should be: 192.168.1.1 and username/password: root/admin. In case of a different firmware, you can use web based recovery described below. Use the following command to perform the sysupgrade (for the 128MB RAM/16MB flash version): sysupgrade -n -F lede-ramips-mt76x8-u7628-01-128M-16M-squashfs-sysupgrade.bin Recovery: This board contains a Chinese, closed-source bootloader called Breed (Boot and Recovery Environment for Embedded Devices). Breed supports web recovery and to enter it, you keep the reset button pressed for around 5 seconds during boot. Your machine will be assigned an IP through DHCP and the router will use IP address 192.168.1.1. The recovery website is in Chinese, but is easy to use. Click on the second item in the list to access the recovery page, then the second item on the next page is where you select the firmware. In order to start the recovery, you click the button at the bottom. SDXC/GPIO header (J3): 1. SDXC_D3 / I2C_SCLK 2. SDXC_D2 / I2C_SD 3. SDXC_D1 / I2S_DI 4. SDXC_D0 / I2S_WS 5. SDXC_CMD / I2S_CLK 6. SDXC_CLK / GPIO0 7. SDXC_CD / UART_RXD1 8. UART_TXD1 9. 3V3 10. GND Other notes: 1. The board is available with different amounts of RAM and flash. We have only added support for the 128/16 MB configuration, as that seems to be the default. However, all the required infrastructure is in place for making support for the other configurations easy. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com> Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
2017-11-03 20:12:49 +00:00
partition@50000 {
compatible = "denx,uimage";
label = "firmware";
reg = <0x50000 0xfb0000>;
};
ramips: add support for UniElec U7628-01 UniElec U7628-01 is a router platform board based on MediaTek MT7628AN. The device has the following specifications: - MT7628AN (580MHz) - 64/128/256 MB of RAM (DDR2) - 8/16 MB of flash (SPI NOR) - 5x 10/100 Mbps Ethernet (MT7628 built-in switch) - 1x 2T2R 2.4 GHz Wi-Fi (MT7628) - 1x miniPCIe slot (with PCIe and USB 2.0 buses) - 1x miniSIM slot - 1x microSD slot - 1x USB 2.0 port - 7x single-color LEDs (GPIO-controlled) - 1x bi-color LED (green GPIO-controlled, red -> LED_WLAN# in miniPCIe) - 1x reset button - 1x UART header (4-pins) - 1x SDXC/GPIO header (10-pins, connected with microSD slot) - 1x DC jack for main power (12 V) The following has been tested and is working: - Ethernet switch - miniPCIe slot (tested with modem and Wi-Fi card) - miniSIM slot - sysupgrade - reset button - USB 2.0 port* Due to a missing driver (MMC over GPIO) this is not supported: - microSD card reader * Warning: USB buses in miniPCIe and regular A-type socket are connected together, without any proper analog switch or USB HUB. Installation: This board might come with a different firmware versions (MediaTek SDK, PandoraBox, Padavan, etc.). If your board comes with PandoraBox, you can install LEDE using sysupgrade. Just SSH to the router and perform forced sysupgrade (due to a board name mismatch). The default IP of this board should be: 192.168.1.1 and username/password: root/admin. In case of a different firmware, you can use web based recovery described below. Use the following command to perform the sysupgrade (for the 128MB RAM/16MB flash version): sysupgrade -n -F lede-ramips-mt76x8-u7628-01-128M-16M-squashfs-sysupgrade.bin Recovery: This board contains a Chinese, closed-source bootloader called Breed (Boot and Recovery Environment for Embedded Devices). Breed supports web recovery and to enter it, you keep the reset button pressed for around 5 seconds during boot. Your machine will be assigned an IP through DHCP and the router will use IP address 192.168.1.1. The recovery website is in Chinese, but is easy to use. Click on the second item in the list to access the recovery page, then the second item on the next page is where you select the firmware. In order to start the recovery, you click the button at the bottom. SDXC/GPIO header (J3): 1. SDXC_D3 / I2C_SCLK 2. SDXC_D2 / I2C_SD 3. SDXC_D1 / I2S_DI 4. SDXC_D0 / I2S_WS 5. SDXC_CMD / I2S_CLK 6. SDXC_CLK / GPIO0 7. SDXC_CD / UART_RXD1 8. UART_TXD1 9. 3V3 10. GND Other notes: 1. The board is available with different amounts of RAM and flash. We have only added support for the 128/16 MB configuration, as that seems to be the default. However, all the required infrastructure is in place for making support for the other configurations easy. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com> Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
2017-11-03 20:12:49 +00:00
};
};
};
&ethernet {
nvmem-cells = <&macaddr_factory_28>;
nvmem-cell-names = "mac-address";
};