ExternalVendorCode/openwrt
1
0
Fork 0
mirror of https://github.com/openwrt/openwrt.git synced 2024-12-20 14:13:16 +00:00
Code Issues Actions 4 Packages Projects Releases Wiki Activity
713be75439
openwrt/package/boot/uboot-envtools/files/kirkwood

38 lines
655 B
Plaintext
Raw Normal View History

uboot-envtools: add kirkwood board support SVN-Revision: 32756
2012-07-16 22:32:00 +00:00
#
uboot-envtools: add support for kirkwood ea4500 Signed-off-by: Luka Perkov <luka@openwrt.org> SVN-Revision: 40872
2014-05-28 21:43:42 +00:00
# Copyright (C) 2012-2014 OpenWrt.org
uboot-envtools: add kirkwood board support SVN-Revision: 32756
2012-07-16 22:32:00 +00:00
#
[ -e /etc/config/ubootenv ] && exit 0
touch /etc/config/ubootenv
. /lib/uboot-envtools.sh
. /lib/functions.sh
treewide: use the generic board_name function Use the generic function instead ot the target specific ones. Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-05-12 20:36:07 +00:00
board=$(board_name)
uboot-envtools: use new scripts from /lib/ to match boards Signed-off-by: Luka Perkov <luka@openwrt.org> SVN-Revision: 41340
2014-06-26 10:14:14 +00:00
case "$board" in
kirkwood: add support for Check Point L-50 This patch adds support for the Check Point L-50 from 600/1100 series routers. Specification: -CPU: Marvell Kirkwood 88F6281 1200MHz -RAM: 512MB -Flash: NAND 512MB -WiFi: mPCIe card based on Atheros AR9287 b/g/n -WAN: 1 Gigabit Port (Marvell 88E1116R PHY) -LAN: 9 Gigabit Ports (2x Marvell 88E6171(5+4)) -USB: 2x USB2.0 -Express card slot -SD card slot -Serial console: RJ-45 115200 8n1 -Unsupported DSL Known issues: -DSL not supported -Expresscard not tested Installation: Step one -> backup: make backup u-boot and env for revert stock posibility make backup dsl_mac_addr, dmz_mac_addr, eth1addr, ethaddr and all lanX_mac_addr Step two -> Use kwboot tool to upload openwrt u-boot to RAM: run kwboot: "kwboot -B 115200 /dev/ttyUSB0 -b u-boot.kwb -p -t" end start u-boot Step three -> Restore macs (e.g. below): setenv eth1addr 00:1C:XX:XX:XX:6C setenv ethaddr 00:1C:XX:XX:XX:6B setenv lan1_mac_addr 00:1C:XX:XX:XX:6C setenv lan2_mac_addr 00:1C:XX:XX:XX:6D setenv lan3_mac_addr 00:1C:XX:XX:XX:6E setenv lan4_mac_addr 00:1C:XX:XX:XX:6F setenv lan5_mac_addr 00:1C:XX:XX:XX:70 setenv lan6_mac_addr 00:1C:XX:XX:XX:71 setenv lan7_mac_addr 00:1C:XX:XX:XX:72 setenv lan8_mac_addr 00:1C:XX:XX:XX:73 setenv dmz_mac_addr 00:1C:XX:XX:XX:74 setenv dsl_mac_addr 00:1C:XX:XX:XX:75 Step four -> flash u-boot: mw 0x0800000 0xffff 0x100000 nand erase 0x0 100000 tftp 0x0800000 openwrt-kirkwood-l50-u-boot.kwb nand write 0x0800000 0x0 0x100000 saveenv Step five -> run initramfs image: tftpboot 0x02000000 openwrt.bin; bootm 0x02000000; Step six -> install sysupgrade OpenWrt image: copy to /tmp/ sysupgrade image run sysupgrade Back to stock: Restore original u-boot end env. Install factory image via stock u-boot. Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2020-01-26 16:22:28 +00:00
checkpoint,l-50|\
kirkwood: sort occurrences of boardame alphabetically This restores the alphabetical sort that was present before the renaming of boardname. Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-01-08 22:49:22 +00:00
cloudengines,pogoe02|\
cloudengines,pogoplugv4|\
kirkwood: Add support for Sheevaplug Globalscale SheevaPlug: * Marvell Kirkwood 88F6281 * 512 MB SDRAM * 512 MB Flash * Gigabit Network * USB 2.0 * SD slot * Serial console The device is supported in mainline uboot/linux the commit adds only some openwrt config for building an image. Installation: 1 - Update uboot: setenv ipaddr '192.168.0.111' setenv serverip '192.168.0.1' tftpboot u-boot.kwb nand erase 0x0 0x100000 nand write 0x800000 0x0 0x100000 reset 2 - Install OpenWRT: setenv ethaddr 00:50:43:01:xx:xx saveenv setenv ipaddr '192.168.0.111' setenv serverip '192.168.0.1' tftpboot openwrt-kirkwood-globalscale_sheevaplug-squashfs-factory.bin nand erase.part ubi nand write 0x800000 ubi 0x600000 reset Signed-off-by: BERENYI Balazs <balazs@wee.hu> Reviewed-by: Pawel Dembicki <paweldembicki@gmail.com> [add vendor name for uboot-kirkwood, merge patches, copy to 5.10, add AUTORELEASE for uboot-kirkwood, refresh patches] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-01-02 18:49:42 +00:00
globalscale,sheevaplug|\
kirkwood: add support for Iomega Storcenter ix2-200 Iomega Storcenter ix2-200 is a dual SATA NAS powered by a Marvell Kirkwood SoC clocked at 1GHz. It has 256MB of RAM and 32MB of flash memory, 3x USB 2.0 and 1x 1Gbit/s NIC Specification: - SoC: Marvell Kirkwood 88F6281 - CPU/Speed: 1000Mhz - Flash-Chip: Hynix NAND - Flash size: 32 MiB,erase size:16 KiB,page size:512,OOB size:16 - RAM: 256MB - LAN: 1x 1000 Mbps Ethernet - WiFi: none - 3x USB 2.0 - UART: for serial console Installation instructions - easy steps: 1. download factory.bin and copy into tftp server 2. access uboot environment with serial cable and run ``` setenv mainlineLinux yes setenv arcNumber 1682 setenv console 'console=ttyS0,115200n8' setenv mtdparts 'mtdparts=orion_nand:0x100000@0x000000(u-boot)ro,0x20000@0xA0000(u-boot environment)ro,0x300000@0x100000(kernel),0x1C00000@0x400000(ubi)' setenv bootargs_root 'root=' setenv bootcmd 'setenv bootargs ${console} ${mtdparts} ${bootargs_root}; nand read.e 0x800000 0x100000 0x300000; bootm 0x00800000' saveenv setenv serverip 192.168.1.1 setenv ipaddr 192.168.1.13 tftpboot 0x00800000 factory.bin nand erase 0x100000 $(filesize) nand write 0x00800000 0x100000 $(filesize) run bootcmd ``` 3. access openwrt by dhcp ip address assigned by your router (p.ex: 192.168.1.13) Installation steps nand bad blocks proof: 1. download initramfs-uImage and copy into usb ext2 partition ``` mkfs.ext2 -L ext2 /dev/sdh1 mount -t ext2 /dev/sdh1 /mnt cp initramfs-uImage /mnt/initramfs.bin umount /mnt ``` 2. access uboot environment with serial cable and run ``` setenv mainlineLinux yes setenv arcNumber 1682 setenv console 'console=ttyS0,115200n8' setenv mtdparts 'mtdparts=orion_nand:0x100000@0x000000(u-boot)ro,0x20000@0xA0000(u-boot environment)ro,0x300000@0x100000(kernel),0x1C00000@0x400000(ubi)' setenv bootargs_root 'root=' setenv bootcmd 'setenv bootargs ${console} ${mtdparts} ${bootargs_root}; nand read.e 0x800000 0x100000 0x300000; bootm 0x00800000' saveenv usb reset; ext2load usb 0:1 0x00800000 /initramfs.bin; bootm 0x00800000 ``` 3. log into openwrt and sysupgrade to install into flash ``` sysupgrade -n /tmp/sysupgrade.bin ``` 4. access openwrt by dhcp ip address assigned by your router (p.ex: 192.168.1.13) Signed-off-by: Ademar Arvati Filho <arvati@hotmail.com>
2018-07-06 00:56:58 +00:00
iom,ix2-200|\
kirkwood: use real model names for Linksys devices This replaces the internal device names "Audi" and "Viper" with the real model names, which a user would look for. This makes the Linksys devices on this target consistent with the names recently changed for mvebu based on the same idea. As a consequence, the "viper" device definition is split into two separate definitions with the correct names for both real models. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-06-12 22:36:01 +00:00
linksys,e4200-v2|\
linksys,ea4500|\
kirkwood: sort occurrences of boardame alphabetically This restores the alphabetical sort that was present before the renaming of boardname. Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-01-08 22:49:22 +00:00
raidsonic,ib-nas62x0|\
seagate,dockstar|\
kirkwood: use the generic board detect Drop the target specific detection function in favour of the generic one provided by base-files. Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-12-28 09:18:48 +00:00
zyxel,nsa310b|\
kirkwood: add support for Zyxel NSA310S Zyxel NSA310S is a NAS based on Marvell kirkwood SoC. Specification: - Processor Marvell 88F6702 1 GHz - 256MB RAM - 128MB NAND - 1x GBE LAN port (PHY: Marvell 88E1318) - 2x USB 2.0 - 1x SATA - 3x button - 7x leds - serial on J1 connector (115200 8N1) (GND-NOPIN-RX-TX-VCC) Known issues: - no kernel module for RTC. [*] - buzzer (connected to MPP43) need to be drived by 1kHz signal - no kernel module for internal MCU connected via I2C[**] [*] Karoly Pocsi made simple, unofficial driver for HT1382. It can be found here: https://www.madadmin.com/zyxel-nsa320s-es-debian-linux-4-resz/ [**] Karoly Pocsi found how CPU talk with MCU: It is possible to query the MCU-controlled fan speed and temperature: i2cget -y 0x0 0x0a 0x07 i2cget -y 0x0 0x0a 0x08 The first value (0x07) is the temperature in ° C, the second (0x08) is the time in milliseconds to complete one fan revolution (rpm = 60,000 / value). Info translated from: https://www.madadmin.com/zyxel-nsa320s-es-debian-linux-4-resz/ Installation: TFTP: 1. Run serial console and go to u-boot. 2. Copy u-boot via tftp and write to NAND: => mw 0x0800000 0xffff 0x100000 => nand erase 0x0 100000 => setenv ipaddr 192.168.1.2 => setenv serverip 192.168.1.4 => tftp 0x0800000 nsa310s-u-boot.kwb => nand write 0x0800000 0x0 0x100000 => reset 3. Run new u-Boot, repair bootcmd and restore MAC address from sticker => setenv ethaddr AA:BB:CC:DD:EE:FF => saveenv 4. Copy and run initramfs image => setenv ipaddr 192.168.1.2 => setenv serverip 192.168.1.4 => tftpboot zyxel_nsa310s-initramfs-uImage => bootm 0x800000 5. Download sysupgrade image and perform sysupgrade USB: 1. Prepare usb fat32 drive with u-boot.kwb and initramfs image. Stick it to USB 2.0 port. 2. Run serial console and go to u-boot. 3. Copy u-boot from usb and write to NAND: => mw 0x0800000 0xffff 0x100000 => nand erase 0x0 100000 => usb start => fatload usb 0 0x0800000 u-boot.kwb => nand write 0x0800000 0x0 0x100000 => reset 4. Run new u-Boot, repair bootcmd and restore MAC address from sticker => setenv ethaddr AA:BB:CC:DD:EE:FF => saveenv 5. Copy and run initramfs image: => usb start => fatload usb 0 0x0800000 initramfs-uImage => bootm 0x800000 6. Download sysupgrade image and perform sysupgrade. Based on work ThBexx <thomas.beckler@hotmail.com> DTS based on dropped support in 0ebdf0c. Tested-by: Lech Perczak <lech.perczak@gmail.com> Reviewed-by: Lech Perczak <lech.perczak@gmail.com> Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com> [NSA310s -> NSA310S in DEVICE_MODEL] Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-05-02 13:33:14 +00:00
zyxel,nsa310s|\
kirkwood: sort occurrences of boardame alphabetically This restores the alphabetical sort that was present before the renaming of boardname. Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-01-08 22:49:22 +00:00
zyxel,nsa325)
uboot-envtools: add kirkwood board support SVN-Revision: 32756
2012-07-16 22:32:00 +00:00
ubootenv_add_uci_config "/dev/mtd1" "0x0" "0x20000" "0x20000"
;;
kirkwood: use real model names for Linksys devices This replaces the internal device names "Audi" and "Viper" with the real model names, which a user would look for. This makes the Linksys devices on this target consistent with the names recently changed for mvebu based on the same idea. As a consequence, the "viper" device definition is split into two separate definitions with the correct names for both real models. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-06-12 22:36:01 +00:00
linksys,ea3500)
uboot-envtools: kirkwood: fix EA35/4500 board names Signed-off-by: Claudio Leite <leitec@staticky.com> SVN-Revision: 47457
2015-11-11 12:48:29 +00:00
ubootenv_add_uci_config "/dev/mtd1" "0x0" "0x4000" "0x4000"
;;
uboot-envtools: add kirkwood board support SVN-Revision: 32756
2012-07-16 22:32:00 +00:00
esac
config_load ubootenv
config_foreach ubootenv_add_app_config ubootenv
exit 0
Reference in New Issue Copy Permalink