ExternalVendorCode/openwrt
1
0
Fork 0
mirror of https://github.com/openwrt/openwrt.git synced 2025-01-12 07:53:07 +00:00
Code Issues Actions 4 Packages Projects Releases Wiki Activity
6e7bc0c243
openwrt/target/linux/ath79/dts/ar9342_ubnt_bullet-m-xw.dts

31 lines
448 B
Plaintext
Raw Normal View History

ath79: ubnt-bullet-m-xw: Change DTS license to GPL-2.0-or-later OR MIT Having MIT as alternative is sometimes preferred by upstream maintainers and allows sharing that simple code with other projects. We don't really want multiple DTS versions for the same device. Signed-off-by: Petr Štetiar <ynezz@true.cz>
2018-11-29 08:27:23 +00:00
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
ath79: Add support for Ubiquity Bullet M (XW) CPU: AR9342 SoC RAM: 64 MB DDR2 Flash: 8 MB NOR SPI Ports: 100 MBit (24V PoE in) WLAN: 2.4/5 GHz UART: 1 UART on PCB marked as J1 with 115200 8N1 config LEDs: Power, Ethernet, 4x RSSI LEDs (orange, red, 2x green) Buttons: Reset UART connection details .---------------------------------. | | [ETH] J1 [ANT] | o VCC o RX o TX o GND | `---------------------------------' Flashing instructions A) Serial console, U-Boot and TFTP 1. Connect to serial header J1 on the PCB 2. Power on device and enter U-Boot console 3. Set up TFTP server serving an OpenWrt initramfs build 4. Load initramfs build using the command tftpboot in the U-Boot cli 5. Boot the loaded image using the command bootm 6. Copy squashfs OpenWrt sysupgrade build to the booted device 7. Use mtd to write sysupgrade to partition "firmware" 8. Reboot and enjoy B) Experimental factory image flashing over SSH from airOS v6.1.7 1. You need to flash your UBNT M2HP with airOS v6.1.7 firmware no other airOS version is currently supported 2. git clone https://github.com/true-systems/ubnt-bullet-m2hp-openwrt-flashing 3. cd ubnt-bullet-m2hp-openwrt-flashing 4. make flash-factory FW_OWRT=/path/to/your/openwrt-ath79-generic-ubnt_bullet-m-xw-squashfs-factory.bin Tested only on Bullet M2HP. Signed-off-by: Petr Štetiar <ynezz@true.cz>
2018-11-17 07:01:55 +00:00
ath79: generic: rework ar9342_ubnt_xw dtsi, and add support for Ubiquiti LiteBeam M5 (XW), Ubiquiti AirGrid M5 HP (XW), Ubiquiti PowerBeam M5 300 (XW) Add support for Ubiquiti LiteBeam M5 (XW). The device was previously supported in ar71xx. See commit: https://git.openwrt.org/?p=openwrt/openwrt.git;a=commit;h=d0988235dd277b9a832bbc4b2a100ac6e821f577 Add ALTX_MODEL for Ubiquiti AirGrid M5 HP (XW), Ubiquiti PowerBeam M5 300 (XW) in generic-ubnt.mk This models are identical (firmware-wise) to the already supported Ubiquiti Nanostation Loco M (XW) Add also Ubiquiti NanoBeam M5 to ALTX_MODEL of Ubiquiti Nanostation Loco M (XW) since it's another clone. Tested on: - Ubiquiti LiteBeam M5 (XW) - Ubiquiti PowerBeam M5 (XW) This also modify target/ath79/dts/ar9342_ubnt_xw.dtsi to use nvmem for calibration data Checked that the caldata size in the eeprom partition are actually 0x440 on: - Ubiquiti PowerBeam M5 (XW) - Ubiquiti Nanostation M5 (XW) - Ubiquiti LiteBeam M5 (XW) - Ubiquiti AirGrid M5 HP (XW) Signed-off-by: Samuele Longhi <agave@dracaena.it>
2023-12-20 18:27:15 +00:00
#include "ar9342_ubnt_xw_rssileds.dtsi"
ath79: Add support for Ubiquity Bullet M (XW) CPU: AR9342 SoC RAM: 64 MB DDR2 Flash: 8 MB NOR SPI Ports: 100 MBit (24V PoE in) WLAN: 2.4/5 GHz UART: 1 UART on PCB marked as J1 with 115200 8N1 config LEDs: Power, Ethernet, 4x RSSI LEDs (orange, red, 2x green) Buttons: Reset UART connection details .---------------------------------. | | [ETH] J1 [ANT] | o VCC o RX o TX o GND | `---------------------------------' Flashing instructions A) Serial console, U-Boot and TFTP 1. Connect to serial header J1 on the PCB 2. Power on device and enter U-Boot console 3. Set up TFTP server serving an OpenWrt initramfs build 4. Load initramfs build using the command tftpboot in the U-Boot cli 5. Boot the loaded image using the command bootm 6. Copy squashfs OpenWrt sysupgrade build to the booted device 7. Use mtd to write sysupgrade to partition "firmware" 8. Reboot and enjoy B) Experimental factory image flashing over SSH from airOS v6.1.7 1. You need to flash your UBNT M2HP with airOS v6.1.7 firmware no other airOS version is currently supported 2. git clone https://github.com/true-systems/ubnt-bullet-m2hp-openwrt-flashing 3. cd ubnt-bullet-m2hp-openwrt-flashing 4. make flash-factory FW_OWRT=/path/to/your/openwrt-ath79-generic-ubnt_bullet-m-xw-squashfs-factory.bin Tested only on Bullet M2HP. Signed-off-by: Petr Štetiar <ynezz@true.cz>
2018-11-17 07:01:55 +00:00
/ {
ath79: add SoC or family compatible Add missing SoC specific compatibles and/or inherit the family compatibles like "ubnt,xm". Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-12-06 10:16:47 +00:00
compatible = "ubnt,bullet-m-xw", "ubnt,xw", "qca,ar9342";
ath79: Add support for Ubiquity Bullet M (XW) CPU: AR9342 SoC RAM: 64 MB DDR2 Flash: 8 MB NOR SPI Ports: 100 MBit (24V PoE in) WLAN: 2.4/5 GHz UART: 1 UART on PCB marked as J1 with 115200 8N1 config LEDs: Power, Ethernet, 4x RSSI LEDs (orange, red, 2x green) Buttons: Reset UART connection details .---------------------------------. | | [ETH] J1 [ANT] | o VCC o RX o TX o GND | `---------------------------------' Flashing instructions A) Serial console, U-Boot and TFTP 1. Connect to serial header J1 on the PCB 2. Power on device and enter U-Boot console 3. Set up TFTP server serving an OpenWrt initramfs build 4. Load initramfs build using the command tftpboot in the U-Boot cli 5. Boot the loaded image using the command bootm 6. Copy squashfs OpenWrt sysupgrade build to the booted device 7. Use mtd to write sysupgrade to partition "firmware" 8. Reboot and enjoy B) Experimental factory image flashing over SSH from airOS v6.1.7 1. You need to flash your UBNT M2HP with airOS v6.1.7 firmware no other airOS version is currently supported 2. git clone https://github.com/true-systems/ubnt-bullet-m2hp-openwrt-flashing 3. cd ubnt-bullet-m2hp-openwrt-flashing 4. make flash-factory FW_OWRT=/path/to/your/openwrt-ath79-generic-ubnt_bullet-m-xw-squashfs-factory.bin Tested only on Bullet M2HP. Signed-off-by: Petr Štetiar <ynezz@true.cz>
2018-11-17 07:01:55 +00:00
model = "Ubiquiti Bullet M (XW)";
};
&mdio0 {
status = "okay";
phy4: ethernet-phy@4 {
reg = <4>;
ath79: ubnt-bullet-m-xw: set PHY max-speed to 100Mbps Onboard AR8035 PHY supports 1000Base-T operation, but onboard Ethernet magnetics do not. Reduce advertised link speeds to 100Mbps and lower. Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
2024-01-04 00:22:26 +00:00
max-speed = <100>;
ath79: Add support for Ubiquity Bullet M (XW) CPU: AR9342 SoC RAM: 64 MB DDR2 Flash: 8 MB NOR SPI Ports: 100 MBit (24V PoE in) WLAN: 2.4/5 GHz UART: 1 UART on PCB marked as J1 with 115200 8N1 config LEDs: Power, Ethernet, 4x RSSI LEDs (orange, red, 2x green) Buttons: Reset UART connection details .---------------------------------. | | [ETH] J1 [ANT] | o VCC o RX o TX o GND | `---------------------------------' Flashing instructions A) Serial console, U-Boot and TFTP 1. Connect to serial header J1 on the PCB 2. Power on device and enter U-Boot console 3. Set up TFTP server serving an OpenWrt initramfs build 4. Load initramfs build using the command tftpboot in the U-Boot cli 5. Boot the loaded image using the command bootm 6. Copy squashfs OpenWrt sysupgrade build to the booted device 7. Use mtd to write sysupgrade to partition "firmware" 8. Reboot and enjoy B) Experimental factory image flashing over SSH from airOS v6.1.7 1. You need to flash your UBNT M2HP with airOS v6.1.7 firmware no other airOS version is currently supported 2. git clone https://github.com/true-systems/ubnt-bullet-m2hp-openwrt-flashing 3. cd ubnt-bullet-m2hp-openwrt-flashing 4. make flash-factory FW_OWRT=/path/to/your/openwrt-ath79-generic-ubnt_bullet-m-xw-squashfs-factory.bin Tested only on Bullet M2HP. Signed-off-by: Petr Štetiar <ynezz@true.cz>
2018-11-17 07:01:55 +00:00
};
};
&eth0 {
status = "okay";
ath79: ubnt-bullet-m-xw: fix Ethernet PHY traffic Since commit 6f2e1b7485f0 ("ath79: disable delays on AT803X config init") Ubiquiti XW boards equipped with AR8035 PHY suffered from lack of outbound traffic on the Ethernet port. This was caused by the fact, the U-boot has set this during boot and it wasn't reset by the PHY driver, and the corresponding setting in device tree was wrong. Set the 'phy-mode = "rgmii-txid"' at the &eth0, and drop this property from PHY node, as it is not parsed there. This causes the device to connect using Ethernet once again. Fixes: db4b6535f837 ("ath79: Add support for Ubiquity Bullet M (XW)") Fixes: 6f2e1b7485f0 ("ath79: disable delays on AT803X config init") Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
2024-01-21 23:14:16 +00:00
phy-mode = "rgmii-txid";
ath79: Add support for Ubiquity Bullet M (XW) CPU: AR9342 SoC RAM: 64 MB DDR2 Flash: 8 MB NOR SPI Ports: 100 MBit (24V PoE in) WLAN: 2.4/5 GHz UART: 1 UART on PCB marked as J1 with 115200 8N1 config LEDs: Power, Ethernet, 4x RSSI LEDs (orange, red, 2x green) Buttons: Reset UART connection details .---------------------------------. | | [ETH] J1 [ANT] | o VCC o RX o TX o GND | `---------------------------------' Flashing instructions A) Serial console, U-Boot and TFTP 1. Connect to serial header J1 on the PCB 2. Power on device and enter U-Boot console 3. Set up TFTP server serving an OpenWrt initramfs build 4. Load initramfs build using the command tftpboot in the U-Boot cli 5. Boot the loaded image using the command bootm 6. Copy squashfs OpenWrt sysupgrade build to the booted device 7. Use mtd to write sysupgrade to partition "firmware" 8. Reboot and enjoy B) Experimental factory image flashing over SSH from airOS v6.1.7 1. You need to flash your UBNT M2HP with airOS v6.1.7 firmware no other airOS version is currently supported 2. git clone https://github.com/true-systems/ubnt-bullet-m2hp-openwrt-flashing 3. cd ubnt-bullet-m2hp-openwrt-flashing 4. make flash-factory FW_OWRT=/path/to/your/openwrt-ath79-generic-ubnt_bullet-m-xw-squashfs-factory.bin Tested only on Bullet M2HP. Signed-off-by: Petr Štetiar <ynezz@true.cz>
2018-11-17 07:01:55 +00:00
phy-handle = <&phy4>;
gmac-config {
device = <&gmac>;
rxd-delay = <3>;
rxdv-delay = <3>;
};
};
Reference in New Issue Copy Permalink