ExternalVendorCode/openwrt
1
0
Fork 0
mirror of https://github.com/openwrt/openwrt.git synced 2024-12-25 08:21:14 +00:00
Code Issues Actions 3 Packages Projects Releases Wiki Activity
6e0f0eae5b
openwrt/target/linux/ath79/image/generic-ubnt.mk

282 lines
7.7 KiB
Makefile
Raw Normal View History

ath79: move ubnt-xm to tiny ath79 has was bumped to 5.10. With this, as with every kernel change, the kernel has become larger. However, although the kernel gets bigger, there are still enough flash resources. But the RAM reaches its capacity limits. The tiny image comes with fewer kernel flags enabled and fewer daemons. Improves: 15aa53d7ee65 ("ath79: switch to Kernel 5.10") Tested-by: Robert Foss <me@robertfoss.se> Signed-off-by: Nick Hainke <vincent@systemli.org>
2021-12-25 08:19:52 +00:00
include ./common-ubnt.mk
ath79: add support for Ubiquiti airCube AC The Ubiquiti Network airCube AC is a cube shaped device supporting 2.4 GHz and 5 GHz with internal 2x2 MIMO antennas. It can be powered with either one of: - 24v power supply with 3.0mm x 1.0mm barrel plug - 24v passive PoE on first LAN port There are four 10/100/1000 Mbps ports (1 * WAN + 3 * LAN). First LAN port have optional PoE passthrough to the WAN port. SoC: Qualcomm / Atheros AR9342 RAM: 64 MB DDR2 Flash: 16 MB SPI NOR Ethernet: 4x 10/100/1000 Mbps (1 WAN + 3 LAN) LEDS: 1x via a SPI controller (not yet supported) Buttons: 1x Reset Serial: 1x (only RX and TX); 115200 baud, 8N1 Missing features: - LED control is not supported Physical to internal switch port mapping: - physical port #1 (poe in) = switchport 2 - physical port #2 = switchport 3 - physical port #3 = switchport 5 - physical port #4 (wan/poe out) = switchport 4 Factory update is tested and is the same as for Ubiquiti AirCube ISP hence the shared configuration between that devices. Signed-off-by: Roman Kuzmitskii <damex.pp@icloud.com>
2020-10-04 05:43:41 +00:00
define Device/ubnt_aircube-ac
$(Device/ubnt-acb)
SOC := ar9342
DEVICE_MODEL := airCube AC
UBNT_CHIP := ar9342
DEVICE_PACKAGES += kmod-ath10k-ct-smallbuffers ath10k-firmware-qca988x-ct
endef
TARGET_DEVICES += ubnt_aircube-ac
define Device/ubnt_aircube-isp
$(Device/ubnt-acb)
SOC := qca9533
DEVICE_MODEL := airCube ISP
UBNT_CHIP := qca9533
ath79: rename ubnt,acb-isp to ubnt,aircube-isp Use the full model name for this device to make it easier to recognize for the users and in order to make it consistent with the other devices. While at it, fix sorting in 03_gpio_switches. Signed-off-by: Roman Kuzmitskii <damex.pp@icloud.com> [commit message facelift] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-10-06 12:08:28 +00:00
SUPPORTED_DEVICES += ubnt,acb-isp
ath79: sort device definitions in image/* This applies alphabetic sorting to devices in image/* files. For certain cases, this patch deviates from strict sorting, e.g. to ensure that v10 comes after v9. While at it, fix an indent and remove some useless empty lines. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-08-22 12:34:45 +00:00
endef
ath79: rename ubnt,acb-isp to ubnt,aircube-isp Use the full model name for this device to make it easier to recognize for the users and in order to make it consistent with the other devices. While at it, fix sorting in 03_gpio_switches. Signed-off-by: Roman Kuzmitskii <damex.pp@icloud.com> [commit message facelift] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-10-06 12:08:28 +00:00
TARGET_DEVICES += ubnt_aircube-isp
ath79: sort device definitions in image/* This applies alphabetic sorting to devices in image/* files. For certain cases, this patch deviates from strict sorting, e.g. to ensure that v10 comes after v9. While at it, fix an indent and remove some useless empty lines. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-08-22 12:34:45 +00:00
ath79: Add support for Ubiquiti Bullet AC CPU: Atheros AR9342 rev 3 SoC RAM: 64 MB DDR2 Flash: 16 MB NOR SPI WLAN 2.4GHz: Atheros AR9342 v3 (ath9k) WLAN 5.0GHz: QCA988X Ports: 1x GbE Flashing procedure is identical to other ubnt devices. https://openwrt.org/toh/ubiquiti/common Flashing through factory firmware 1. Ensure firmware version v8.7.0 is installed. Up/downgrade to this exact version. 2. Patch fwupdate.real binary using `hexdump -Cv /bin/ubntbox | sed 's/14 40 fe 27/00 00 00 00/g' | \ hexdump -R > /tmp/fwupdate.real` 3. Make the patched fwupdate.real binary executable using `chmod +x /tmp/fwupdate.real` 4. Copy the squashfs factory image to /tmp on the device 5. Flash OpenWrt using `/tmp/fwupdate.real -m <squashfs-factory image>` 6. Wait for the device to reboot (copied from Ubiquiti NanoBeam AC and modified) Flashing from serial console 1. Connect serial console (115200 baud) 2. Connect ethernet to a network with a TFTP server, through a passive PoE injector. 3. Press a key to obtain a u-boot prompt 4. Set your TFTP server's ip address, with: setenv serverip <tftp-server-address> 5. Set the Bullet AC's ip address, with: setenv ipaddr <bullet-ac-address> 6. Set the boot file, with: setenv bootfile <name-of-initramfs-binary-on-tftp-server> 7. Fetch the binary with tftp: tftpboot 8. Boot the initramfs binary: bootm 9. From the initramfs, fetch the sysupgrade binary, and flash it with sysupgrade. The Bullet AC is identified as a 2WA board by Ubiquiti. As such, the UBNT_TYPE must match from the "Flashing through factory firmware" install instructions to work. Phy0 is QCA988X which can tune either band (2.4 or 5GHz). Phy1 is AR9342, on which 5GHz is disabled. It isn't currently known whether phy1 is routed to the N connector at all. Signed-off-by: Russell Senior <russell@personaltelco.net>
2020-12-23 02:32:54 +00:00
define Device/ubnt_bullet-ac
$(Device/ubnt-2wa)
DEVICE_MODEL := Bullet AC
DEVICE_PACKAGES += kmod-ath10k-ct-smallbuffers ath10k-firmware-qca988x-ct rssileds
endef
TARGET_DEVICES += ubnt_bullet-ac
ath79: Add support for Ubiquity Bullet M (XW) CPU: AR9342 SoC RAM: 64 MB DDR2 Flash: 8 MB NOR SPI Ports: 100 MBit (24V PoE in) WLAN: 2.4/5 GHz UART: 1 UART on PCB marked as J1 with 115200 8N1 config LEDs: Power, Ethernet, 4x RSSI LEDs (orange, red, 2x green) Buttons: Reset UART connection details .---------------------------------. | | [ETH] J1 [ANT] | o VCC o RX o TX o GND | `---------------------------------' Flashing instructions A) Serial console, U-Boot and TFTP 1. Connect to serial header J1 on the PCB 2. Power on device and enter U-Boot console 3. Set up TFTP server serving an OpenWrt initramfs build 4. Load initramfs build using the command tftpboot in the U-Boot cli 5. Boot the loaded image using the command bootm 6. Copy squashfs OpenWrt sysupgrade build to the booted device 7. Use mtd to write sysupgrade to partition "firmware" 8. Reboot and enjoy B) Experimental factory image flashing over SSH from airOS v6.1.7 1. You need to flash your UBNT M2HP with airOS v6.1.7 firmware no other airOS version is currently supported 2. git clone https://github.com/true-systems/ubnt-bullet-m2hp-openwrt-flashing 3. cd ubnt-bullet-m2hp-openwrt-flashing 4. make flash-factory FW_OWRT=/path/to/your/openwrt-ath79-generic-ubnt_bullet-m-xw-squashfs-factory.bin Tested only on Bullet M2HP. Signed-off-by: Petr Štetiar <ynezz@true.cz>
2018-11-17 07:01:55 +00:00
define Device/ubnt_bullet-m-xw
$(Device/ubnt-xw)
ath79: harmonize model names for Ubiquiti devices This harmonizes the model names for the ath79 Ubiquiti devices by applying a few minor cosmetic adjustments: - Removes hyphens where they are not found in the product names (Ubiquiti uses hyphens only for the abbreviated version names like UAP-AC-PRO which we don't use anyway.) - Add (XM) suffix for DTS model strings to help with distinguishing them from their XW counterparts. - Remove DEVICE_VARIANT for LAP-120 which actually was an alternate device name. - Generally make DTS model names and those from generic-ubnt.mk more consistent. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-15 16:41:57 +00:00
DEVICE_MODEL := Bullet M
ath79: include rssileds package for ubnt devices with LEDs Some Ubiquiti devices had the RSSI LEDs configured in 01_leds but were missing the rssileds package, while others that don't have RSSI LEDS had the package included. This commit includes the rssileds package only for those devices that need it. Tested on a NanoStation M XW. Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
2019-11-13 15:18:59 +00:00
DEVICE_PACKAGES += rssileds
ath79: Add support for Ubiquity Bullet M (XW) CPU: AR9342 SoC RAM: 64 MB DDR2 Flash: 8 MB NOR SPI Ports: 100 MBit (24V PoE in) WLAN: 2.4/5 GHz UART: 1 UART on PCB marked as J1 with 115200 8N1 config LEDs: Power, Ethernet, 4x RSSI LEDs (orange, red, 2x green) Buttons: Reset UART connection details .---------------------------------. | | [ETH] J1 [ANT] | o VCC o RX o TX o GND | `---------------------------------' Flashing instructions A) Serial console, U-Boot and TFTP 1. Connect to serial header J1 on the PCB 2. Power on device and enter U-Boot console 3. Set up TFTP server serving an OpenWrt initramfs build 4. Load initramfs build using the command tftpboot in the U-Boot cli 5. Boot the loaded image using the command bootm 6. Copy squashfs OpenWrt sysupgrade build to the booted device 7. Use mtd to write sysupgrade to partition "firmware" 8. Reboot and enjoy B) Experimental factory image flashing over SSH from airOS v6.1.7 1. You need to flash your UBNT M2HP with airOS v6.1.7 firmware no other airOS version is currently supported 2. git clone https://github.com/true-systems/ubnt-bullet-m2hp-openwrt-flashing 3. cd ubnt-bullet-m2hp-openwrt-flashing 4. make flash-factory FW_OWRT=/path/to/your/openwrt-ath79-generic-ubnt_bullet-m-xw-squashfs-factory.bin Tested only on Bullet M2HP. Signed-off-by: Petr Štetiar <ynezz@true.cz>
2018-11-17 07:01:55 +00:00
SUPPORTED_DEVICES += bullet-m-xw
endef
TARGET_DEVICES += ubnt_bullet-m-xw
ath79: add support for Ubiquiti EdgeSwitch/ToughSwitch 5XP The Ubiquiti ToughSwitch 5XP is a 5-port PoE Gigabit switch with a single Fast-Ethernet management port. It supports both 24V passive PoE out on all five ports. Flash: 8 MB RAM: 64 MB SoC: AR7242 Switch: ar8327 USB: 1x USB 2.0 Ethernet: 5x GbE, 1x FE Installation of the firmware is possible either via serial + tftpboot or the factory firmware update function via webinterface. By default the single Fast-Ethernet port labeled "MGMT" is configured as the WAN port. Thus access to the device is only possible via the five switch ports. Serial: 3v3 115200 8n1 The serial header is located in the lower left corner of the switches PCB: ``` | | | | o | o RX | o TX | o GND | | ++ +-++-+ ++ ++ + +--+ ++ +--++--++--+ ``` Signed-off-by: Tobias Schramm <tobleminer@gmail.com> [remove ubnt,sw compatible - fix spelling - wrap commit message - remove superfluous phy-mode property] Signed-off-by: David Bauer <mail@david-bauer.net>
2020-01-01 09:01:48 +00:00
define Device/ubnt_edgeswitch-5xp
$(Device/ubnt-sw)
DEVICE_MODEL := EdgeSwitch 5XP
endef
TARGET_DEVICES += ubnt_edgeswitch-5xp
ath79: add support for Ubiquiti ToughSwitch/EdgeSwitch 8XP Flash: 8 MB RAM: 64 MB SoC: AR7242 Switch: bcm53128 USB: 1x USB 2.0 Ethernet: 8x GbE, 1x FE The Ubiquiti ToughSwitch 8XP is a 8-port PoE Gigabit switch with a single Fast-Ethernet management port. It supports both 24V passive PoE and 48V 802.11af/at PoE out on all eight ports. By default the single Fast-Ethernet port labeled "MGMT" is configured as the WAN port. Thus access to the device is only possible via the eight switch ports. Installation of the firware is possible either via serial + tftpboot or the factory firmware update function via webinterface. Serial: 3v3 115200 8n1 The serial header is located in the lower left corner of the switches PCB: | | | | o | o RX | o TX | o GND | | ++ +-++-+ ++ ++ + +--+ ++ +--++--++--+ Signed-off-by: Tobias Schramm <tobleminer@gmail.com> [fix whitespace issue] Signed-off-by: David Bauer <mail@david-bauer.net>
2019-12-03 21:48:35 +00:00
define Device/ubnt_edgeswitch-8xp
$(Device/ubnt-sw)
DEVICE_MODEL := EdgeSwitch 8XP
ath79: Fix ubnt_edgeswitch-8xp DEVICE_PACKAGES switch-bcm53xx-mdio does not exists, use kmod-switch-bcm53xx-mdio instead. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Cc: Tobias Schramm <tobleminer@gmail.com>
2020-05-13 21:42:15 +00:00
DEVICE_PACKAGES += kmod-switch-bcm53xx-mdio
ath79: add support for Ubiquiti ToughSwitch/EdgeSwitch 8XP Flash: 8 MB RAM: 64 MB SoC: AR7242 Switch: bcm53128 USB: 1x USB 2.0 Ethernet: 8x GbE, 1x FE The Ubiquiti ToughSwitch 8XP is a 8-port PoE Gigabit switch with a single Fast-Ethernet management port. It supports both 24V passive PoE and 48V 802.11af/at PoE out on all eight ports. By default the single Fast-Ethernet port labeled "MGMT" is configured as the WAN port. Thus access to the device is only possible via the eight switch ports. Installation of the firware is possible either via serial + tftpboot or the factory firmware update function via webinterface. Serial: 3v3 115200 8n1 The serial header is located in the lower left corner of the switches PCB: | | | | o | o RX | o TX | o GND | | ++ +-++-+ ++ ++ + +--+ ++ +--++--++--+ Signed-off-by: Tobias Schramm <tobleminer@gmail.com> [fix whitespace issue] Signed-off-by: David Bauer <mail@david-bauer.net>
2019-12-03 21:48:35 +00:00
endef
TARGET_DEVICES += ubnt_edgeswitch-8xp
ath79: Add support for Ubiquiti LiteAP ac (LAP-120) This commit adds support for the Ubiquiti LiteAP ac (LAP-120), an outdoor 5 GHz AC access point with an integrated 120° 16 dBi antenna. The device was previously known as LiteBeam AP ac but was later rebranded. CPU: Atheros AR9342 SoC RAM: 64 MB DDR2 Flash: 16 MB NOR SPI Ports: 1 GbE port (PoE in) WLAN: 5 GHz QCA899X (PCI) The integrated QCA899X is a Ubiquiti branded part with modified vendor and product id (0777:11ac9). It is very similar to the NanoStation loco AC, except for the 2.4 GHz management radio (missing here). Installation procedure is the same as the NanoStation [loco] AC: 1. Connect to serial header on device 2. Power on device and enter uboot console 3. Set up tftp server serving an openwrt initramfs build 4. Load initramfs build using the command tftpboot in the uboot cli 5. Boot the loaded image using the command bootm 6. Copy squashfs openwrt sysupgrade build to the booted device 7. Use mtd to write sysupgrade to partition "firmware" 8. Reboot and enjoy Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
2018-09-19 12:17:35 +00:00
define Device/ubnt_lap-120
$(Device/ubnt-wa)
ath79: harmonize model names for Ubiquiti devices This harmonizes the model names for the ath79 Ubiquiti devices by applying a few minor cosmetic adjustments: - Removes hyphens where they are not found in the product names (Ubiquiti uses hyphens only for the abbreviated version names like UAP-AC-PRO which we don't use anyway.) - Add (XM) suffix for DTS model strings to help with distinguishing them from their XW counterparts. - Remove DEVICE_VARIANT for LAP-120 which actually was an alternate device name. - Generally make DTS model names and those from generic-ubnt.mk more consistent. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-15 16:41:57 +00:00
DEVICE_MODEL := LiteAP ac (LAP-120)
ath79: use ath10k-ct-smallbuffers for 64 MiB devices Signed-off-by: Paul Fertser <fercerpav@gmail.com>
2019-12-22 20:05:13 +00:00
DEVICE_PACKAGES += kmod-ath10k-ct-smallbuffers ath10k-firmware-qca988x-ct
ath79: Add support for Ubiquiti LiteAP ac (LAP-120) This commit adds support for the Ubiquiti LiteAP ac (LAP-120), an outdoor 5 GHz AC access point with an integrated 120° 16 dBi antenna. The device was previously known as LiteBeam AP ac but was later rebranded. CPU: Atheros AR9342 SoC RAM: 64 MB DDR2 Flash: 16 MB NOR SPI Ports: 1 GbE port (PoE in) WLAN: 5 GHz QCA899X (PCI) The integrated QCA899X is a Ubiquiti branded part with modified vendor and product id (0777:11ac9). It is very similar to the NanoStation loco AC, except for the 2.4 GHz management radio (missing here). Installation procedure is the same as the NanoStation [loco] AC: 1. Connect to serial header on device 2. Power on device and enter uboot console 3. Set up tftp server serving an openwrt initramfs build 4. Load initramfs build using the command tftpboot in the uboot cli 5. Boot the loaded image using the command bootm 6. Copy squashfs openwrt sysupgrade build to the booted device 7. Use mtd to write sysupgrade to partition "firmware" 8. Reboot and enjoy Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
2018-09-19 12:17:35 +00:00
endef
TARGET_DEVICES += ubnt_lap-120
ath79: add support for Ubiquiti LiteBeam AC Gen2 Hardware: * SoC: Atheros AR9342-BL1A * RAM: 64MB DDR2 (Winbond W9751G6KB-25) * Flash: 16MB SPI NOR (Macronix MX25L12835FZ2I-10G) * Ethernet: 1x 10/100/1000 Mbps (Atheros AR8035-A) with 24V PoE support * Wifi 2.4GHz: Atheros AR9340 v2 * WiFi 5GHz: Ubiquiti U-AME-G1-BR4A (rebranded QCA988X v2) * LEDs: 1x Power, 1x Ethernet * Buttons: 1x Reset * UART: 1x TTL 115200n8, 3.3V RX TX GND, 3.3V pin closest to RJ45 port The LEDs do not seem to be connected to any GPIO, so there is currently no way to control them. Installation via U-Boot, TFTP and serial console: * Configure your TFTP server with IP 192.168.1.254 * Connect serial console and power up the device * Hit any key to stop autoboot * tftpboot 0x81000000 openwrt-ath79-generic-ubnt_litebeam-ac-gen2-initramfs-kernel.bin * bootm 0x81000000 * copy openwrt-ath79-generic-ubnt_litebeam-ac-gen2-squashfs-sysupgrade.bin to /tmp * sysupgrade /tmp/openwrt-ath79-generic-ubnt_litebeam-ac-gen2-squashfs-sysupgrade.bin Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be> Acked-by: Petr Štetiar <ynezz@true.cz> Acked-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-04-12 17:21:58 +00:00
define Device/ubnt_litebeam-ac-gen2
$(Device/ubnt-wa)
DEVICE_MODEL := LiteBeam AC
DEVICE_VARIANT := Gen2
ath79: use ath10k-ct-smallbuffers for 64 MiB devices Signed-off-by: Paul Fertser <fercerpav@gmail.com>
2019-12-22 20:05:13 +00:00
DEVICE_PACKAGES := kmod-ath10k-ct-smallbuffers ath10k-firmware-qca988x-ct
ath79: add support for Ubiquiti LiteBeam AC Gen2 Hardware: * SoC: Atheros AR9342-BL1A * RAM: 64MB DDR2 (Winbond W9751G6KB-25) * Flash: 16MB SPI NOR (Macronix MX25L12835FZ2I-10G) * Ethernet: 1x 10/100/1000 Mbps (Atheros AR8035-A) with 24V PoE support * Wifi 2.4GHz: Atheros AR9340 v2 * WiFi 5GHz: Ubiquiti U-AME-G1-BR4A (rebranded QCA988X v2) * LEDs: 1x Power, 1x Ethernet * Buttons: 1x Reset * UART: 1x TTL 115200n8, 3.3V RX TX GND, 3.3V pin closest to RJ45 port The LEDs do not seem to be connected to any GPIO, so there is currently no way to control them. Installation via U-Boot, TFTP and serial console: * Configure your TFTP server with IP 192.168.1.254 * Connect serial console and power up the device * Hit any key to stop autoboot * tftpboot 0x81000000 openwrt-ath79-generic-ubnt_litebeam-ac-gen2-initramfs-kernel.bin * bootm 0x81000000 * copy openwrt-ath79-generic-ubnt_litebeam-ac-gen2-squashfs-sysupgrade.bin to /tmp * sysupgrade /tmp/openwrt-ath79-generic-ubnt_litebeam-ac-gen2-squashfs-sysupgrade.bin Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be> Acked-by: Petr Štetiar <ynezz@true.cz> Acked-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-04-12 17:21:58 +00:00
endef
TARGET_DEVICES += ubnt_litebeam-ac-gen2
ath79: Add support for Ubiquiti NanoBeam AC The NanoBeam is a small AR9342 based directional 5 GHz AC CPE with hardware almost identical to the Ubiquiti NanoStation AC loco. Over the NanoStation AC loco it has 5 additional LEDs. Four of those LEDs are used as rssi indicators, the fifth LED is used as an ethernet link/activity indicator. CPU: Atheros AR9342 SoC RAM: 64 MB DDR2 Flash: 16 MB NOR SPI WLAN: QCA988X Ports: 1x GbE Flashing procedure is identical to the NanoStation AC loco and can be performed either via serial or the factory firmware upgrade. Serial flashing: 1. Connect to serial header on device (8N1 115200) 2. Power on device and enter uboot console 3. Set up tftp server serving an openwrt initramfs build 4. Load initramfs build using the command tftpboot in the uboot cli 5. Boot the loaded image using the command bootm 6. Copy squashfs openwrt sysupgrade build to the booted device 7. Use mtd to write sysupgrade to partition "firmware" 8. Reboot and enjoy Flashing through factory firmware: 1. Ensure firmware version v8.5.0.36727 is installed. Up/downgrade to this exact version. 2. Patch fwupdate.real binary using `hexdump -Cv /bin/ubntbox | sed 's/14 40 fe fe/00 00 00 00/g' | hexdump -R > /tmp/fwupdate.real` 3. Make the patched fwupdate.real binary executable using `chmod +x /tmp/fwupdate.real` 4. Copy the squashfs factory image to /tmp on the device 5. Flash OpenWRT using `/tmp/fwupdate.real -m <squashfs-factory image>` 6. Wait for the device to reboot Thanks to @cybermaus for testing! Tested-by: Maurits van Dueren den Hollander <cybermaus@gmail.com> Signed-off-by: Tobias Schramm <tobleminer@gmail.com>
2019-01-08 14:27:57 +00:00
define Device/ubnt_nanobeam-ac
$(Device/ubnt-wa)
ath79: split DEVICE_TITLE in multiple variables This allows the definition of DEVICE_VENDOR, DEVICE_MODEL and DEVICE_VARIANT. All three are merged together to look the same as the current DEVICE_TITLE. Also, if DEVICE_TITLE is set it's directly used as a *fallback* for devices which weren't upgraded yet. This is based on the work of @sudhanshu16. The motivation is to create JSON files based on provided metadata, needing clear differentiation between vendor, model and revision. Signed-off-by: Paul Spooren <mail@aparcar.org>
2019-06-16 19:34:46 +00:00
DEVICE_MODEL := NanoBeam AC
ath79: Add support for Ubiquiti NanoBeam AC Gen2 CPU: Atheros AR9342 rev 3 SoC RAM: 64 MB DDR2 Flash: 16 MB NOR SPI WLAN 2.4GHz: Atheros AR9342 v3 (ath9k) WLAN 5.0GHz: QCA988X Ports: 2x GbE Flashing procedure is identical to other ubnt devices. https://openwrt.org/toh/ubiquiti/common Flashing through factory firmware 1. Ensure firmware version v8.7.0 is installed. Up/downgrade to this exact version. 2. Patch fwupdate.real binary using `hexdump -Cv /bin/ubntbox | sed 's/14 40 fe 27/00 00 00 00/g' | \ hexdump -R > /tmp/fwupdate.real` 3. Make the patched fwupdate.real binary executable using `chmod +x /tmp/fwupdate.real` 4. Copy the squashfs factory image to /tmp on the device 5. Flash OpenWrt using `/tmp/fwupdate.real -m <squashfs-factory image>` 6. Wait for the device to reboot (copied from Ubiquiti NanoBeam AC and modified) To keep it consistent, we will add the gen1 variant to the nanobeam ac gen1. Signed-off-by: Nick Hainke <vincent@systemli.org>
2020-10-25 13:51:55 +00:00
DEVICE_VARIANT := Gen1
ath79: use ath10k-ct-smallbuffers for 64 MiB devices Signed-off-by: Paul Fertser <fercerpav@gmail.com>
2019-12-22 20:05:13 +00:00
DEVICE_PACKAGES += kmod-ath10k-ct-smallbuffers ath10k-firmware-qca988x-ct rssileds
ath79: Add support for Ubiquiti NanoBeam AC The NanoBeam is a small AR9342 based directional 5 GHz AC CPE with hardware almost identical to the Ubiquiti NanoStation AC loco. Over the NanoStation AC loco it has 5 additional LEDs. Four of those LEDs are used as rssi indicators, the fifth LED is used as an ethernet link/activity indicator. CPU: Atheros AR9342 SoC RAM: 64 MB DDR2 Flash: 16 MB NOR SPI WLAN: QCA988X Ports: 1x GbE Flashing procedure is identical to the NanoStation AC loco and can be performed either via serial or the factory firmware upgrade. Serial flashing: 1. Connect to serial header on device (8N1 115200) 2. Power on device and enter uboot console 3. Set up tftp server serving an openwrt initramfs build 4. Load initramfs build using the command tftpboot in the uboot cli 5. Boot the loaded image using the command bootm 6. Copy squashfs openwrt sysupgrade build to the booted device 7. Use mtd to write sysupgrade to partition "firmware" 8. Reboot and enjoy Flashing through factory firmware: 1. Ensure firmware version v8.5.0.36727 is installed. Up/downgrade to this exact version. 2. Patch fwupdate.real binary using `hexdump -Cv /bin/ubntbox | sed 's/14 40 fe fe/00 00 00 00/g' | hexdump -R > /tmp/fwupdate.real` 3. Make the patched fwupdate.real binary executable using `chmod +x /tmp/fwupdate.real` 4. Copy the squashfs factory image to /tmp on the device 5. Flash OpenWRT using `/tmp/fwupdate.real -m <squashfs-factory image>` 6. Wait for the device to reboot Thanks to @cybermaus for testing! Tested-by: Maurits van Dueren den Hollander <cybermaus@gmail.com> Signed-off-by: Tobias Schramm <tobleminer@gmail.com>
2019-01-08 14:27:57 +00:00
endef
TARGET_DEVICES += ubnt_nanobeam-ac
ath79: Add support for Ubiquiti NanoBeam AC Gen2 CPU: Atheros AR9342 rev 3 SoC RAM: 64 MB DDR2 Flash: 16 MB NOR SPI WLAN 2.4GHz: Atheros AR9342 v3 (ath9k) WLAN 5.0GHz: QCA988X Ports: 2x GbE Flashing procedure is identical to other ubnt devices. https://openwrt.org/toh/ubiquiti/common Flashing through factory firmware 1. Ensure firmware version v8.7.0 is installed. Up/downgrade to this exact version. 2. Patch fwupdate.real binary using `hexdump -Cv /bin/ubntbox | sed 's/14 40 fe 27/00 00 00 00/g' | \ hexdump -R > /tmp/fwupdate.real` 3. Make the patched fwupdate.real binary executable using `chmod +x /tmp/fwupdate.real` 4. Copy the squashfs factory image to /tmp on the device 5. Flash OpenWrt using `/tmp/fwupdate.real -m <squashfs-factory image>` 6. Wait for the device to reboot (copied from Ubiquiti NanoBeam AC and modified) To keep it consistent, we will add the gen1 variant to the nanobeam ac gen1. Signed-off-by: Nick Hainke <vincent@systemli.org>
2020-10-25 13:51:55 +00:00
define Device/ubnt_nanobeam-ac-gen2
$(Device/ubnt-wa)
DEVICE_MODEL := NanoBeam AC
DEVICE_VARIANT := Gen2
DEVICE_PACKAGES += kmod-ath10k-ct-smallbuffers ath10k-firmware-qca988x-ct rssileds
endef
TARGET_DEVICES += ubnt_nanobeam-ac-gen2
ath79: Add support for Ubiquiti NanoBeam AC Gen1 XC The Ubiquiti NanoBeam AC Gen1 XC (NBE-5AC-19) is an outdoor 802.11ac CPE with a waterproof casing (ultrasonically welded) and bulb shaped. Hardware: - SoC: Qualcomm Atheros QCA9558 - RAM: 128 MB DDR2 - Flash: 16 MB SPI NOR - Ethernet: 1x GbE, AR8033 phy connected via SGMII - PSU: 24 Vdc passive PoE - WiFi 5 GHz: Qualcomm Atheros QCA988X - Buttons: 1x reset - LEDs: 1x power, 1x Ethernet, 4x RSSI, all blue - Internal antenna: 19 dBi planar Installation from stock airOS firmware: - Follow instructions for XC-type Ubiquiti devices on OpenWrt wiki at https://openwrt.org/toh/ubiquiti/common Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
2022-01-16 18:00:19 +00:00
define Device/ubnt_nanobeam-ac-xc
$(Device/ubnt-xc)
SOC := qca9558
DEVICE_MODEL := NanoBeam AC
DEVICE_VARIANT := Gen1 (XC)
DEVICE_PACKAGES += kmod-ath10k-ct ath10k-firmware-qca988x-ct rssileds
endef
TARGET_DEVICES += ubnt_nanobeam-ac-xc
ath79: NanoBeam M5 fix target_devices Update the name of for the Ubiquiti NanoBeam M5 to match the auto-generated one at runtime. Otherwise sysupgrade complains about mismatching device names. This also required renaming the DTS. Signed-off-by: Jan-Niklas Burfeind <git@aiyionpri.me>
2022-05-21 15:17:34 +00:00
define Device/ubnt_nanobeam-m5-xw
ath79: add support for Ubiquiti NanoBeam M5 Ubiquiti NanoBeam M5 devices are CPE equipment for customer locations with one Ethernet port and a 5 GHz 300Mbps wireless interface. Specificatons: - Atheros AR9342 - 535 MHz CPU - 64 MB RAM - 8 MB Flash - 1x 10/100 Mbps Ethernet with passive PoE input (24 V) - 6 LEDs of which four are rssi - 1 reset button - UART (4-pin) header on PCB Notes: The device was supported by OpenWrt in ar71xx. Flash instructions (web/ssh/tftp): Loading the image via ssh vias a stock firmware prior "AirOS 5.6". Downgrading stock is possible. * Flashing is possible via AirOS software update page: The "factory" ROM image is recognized as non-native and then installed correctly. AirOS warns to better be familiar with the recovery procedure. * Flashing can be done via ssh, which is becoming difficult due to legacy keyexchange methods. This is an exempary ssh-config: KexAlgorithms +diffie-hellman-group1-sha1 HostKeyAlgorithms ssh-rsa PubkeyAcceptedKeyTypes ssh-rsa User ubnt The password is ubnt. Connecting via IPv6 link local worked best for me. 1. scp the factory image to /tmp 2. fwupdate.real -m /tmp/firmware_image_file.bin -d * Alternatively tftp is possible: 1. Configure PC with static IP 192.168.1.2/24. 2. Enter the rescue mode. Power off the device, push the reset button on the device (or the PoE) and keep it pressed. Power on the device, while still pushing the reset button. 3. When all the leds blink at the same time, release the reset button. 4. Upload the firmware image file via TFTP: tftp 192.168.1.20 tftp> bin tftp> trace Packet tracing on. tftp> put firmware_image.bin Signed-off-by: Jan-Niklas Burfeind <git@aiyionpri.me>
2022-04-23 15:49:34 +00:00
$(Device/ubnt-xw)
DEVICE_MODEL := NanoBeam M5
DEVICE_PACKAGES += rssileds
SUPPORTED_DEVICES += loco-m-xw
endef
ath79: NanoBeam M5 fix target_devices Update the name of for the Ubiquiti NanoBeam M5 to match the auto-generated one at runtime. Otherwise sysupgrade complains about mismatching device names. This also required renaming the DTS. Signed-off-by: Jan-Niklas Burfeind <git@aiyionpri.me>
2022-05-21 15:17:34 +00:00
TARGET_DEVICES += ubnt_nanobeam-m5-xw
ath79: add support for Ubiquiti NanoBeam M5 Ubiquiti NanoBeam M5 devices are CPE equipment for customer locations with one Ethernet port and a 5 GHz 300Mbps wireless interface. Specificatons: - Atheros AR9342 - 535 MHz CPU - 64 MB RAM - 8 MB Flash - 1x 10/100 Mbps Ethernet with passive PoE input (24 V) - 6 LEDs of which four are rssi - 1 reset button - UART (4-pin) header on PCB Notes: The device was supported by OpenWrt in ar71xx. Flash instructions (web/ssh/tftp): Loading the image via ssh vias a stock firmware prior "AirOS 5.6". Downgrading stock is possible. * Flashing is possible via AirOS software update page: The "factory" ROM image is recognized as non-native and then installed correctly. AirOS warns to better be familiar with the recovery procedure. * Flashing can be done via ssh, which is becoming difficult due to legacy keyexchange methods. This is an exempary ssh-config: KexAlgorithms +diffie-hellman-group1-sha1 HostKeyAlgorithms ssh-rsa PubkeyAcceptedKeyTypes ssh-rsa User ubnt The password is ubnt. Connecting via IPv6 link local worked best for me. 1. scp the factory image to /tmp 2. fwupdate.real -m /tmp/firmware_image_file.bin -d * Alternatively tftp is possible: 1. Configure PC with static IP 192.168.1.2/24. 2. Enter the rescue mode. Power off the device, push the reset button on the device (or the PoE) and keep it pressed. Power on the device, while still pushing the reset button. 3. When all the leds blink at the same time, release the reset button. 4. Upload the firmware image file via TFTP: tftp 192.168.1.20 tftp> bin tftp> trace Packet tracing on. tftp> put firmware_image.bin Signed-off-by: Jan-Niklas Burfeind <git@aiyionpri.me>
2022-04-23 15:49:34 +00:00
ath79: Add support for Ubiquiti Nanostation AC 5 GHz AC wireless outdoor PoE CPE with internal 2.4 GHz management radio CPU: Atheros AR9342 SoC RAM: 64 MB DDR2 Flash: 16 MB NOR SPI Switch: QCA8334 Ports: 2 GbE ports (1x PoE in, 1x PoE passthrough) WLAN: 5 GHz QCA899X (PCI) and 2.4 GHZ AR9342 Successor to the old NanoStation M5 with AC wireless. The integrated QCA899X is a Ubiquiti branded part with modified vendor and product id (0777:11ac9). Serial Serial settings: 115200, 8N1 * = plated through hole 0 = nylon screw [Top of device] +--------------------------+ | [label] | | 0 | | 0 | | [ubnt] | | [logo] 3V3 * | | TX * | | RX * | | GND * | | | | * | | * | | * | | * | | 0 | | 0 | | | | | Installation 1. Connect to serial header on device 2. Power on device and enter uboot console 3. Set up tftp server serving an openwrt initramfs build 4. Load initramfs build using the command tftpboot in the uboot cli 5. Boot the loaded image using the command bootm 6. Copy squashfs openwrt sysupgrade build to the booted device 7. Use mtd to write sysupgrade to partition "firmware" 8. Reboot and enjoy Signed-off-by: Tobias Schramm <tobleminer@gmail.com>
2018-09-04 00:08:01 +00:00
define Device/ubnt_nanostation-ac
$(Device/ubnt-wa)
ath79: split DEVICE_TITLE in multiple variables This allows the definition of DEVICE_VENDOR, DEVICE_MODEL and DEVICE_VARIANT. All three are merged together to look the same as the current DEVICE_TITLE. Also, if DEVICE_TITLE is set it's directly used as a *fallback* for devices which weren't upgraded yet. This is based on the work of @sudhanshu16. The motivation is to create JSON files based on provided metadata, needing clear differentiation between vendor, model and revision. Signed-off-by: Paul Spooren <mail@aparcar.org>
2019-06-16 19:34:46 +00:00
DEVICE_MODEL := Nanostation AC
ath79: use ath10k-ct-smallbuffers for 64 MiB devices Signed-off-by: Paul Fertser <fercerpav@gmail.com>
2019-12-22 20:05:13 +00:00
DEVICE_PACKAGES += kmod-ath10k-ct-smallbuffers ath10k-firmware-qca988x-ct rssileds
ath79: Add support for Ubiquiti Nanostation AC 5 GHz AC wireless outdoor PoE CPE with internal 2.4 GHz management radio CPU: Atheros AR9342 SoC RAM: 64 MB DDR2 Flash: 16 MB NOR SPI Switch: QCA8334 Ports: 2 GbE ports (1x PoE in, 1x PoE passthrough) WLAN: 5 GHz QCA899X (PCI) and 2.4 GHZ AR9342 Successor to the old NanoStation M5 with AC wireless. The integrated QCA899X is a Ubiquiti branded part with modified vendor and product id (0777:11ac9). Serial Serial settings: 115200, 8N1 * = plated through hole 0 = nylon screw [Top of device] +--------------------------+ | [label] | | 0 | | 0 | | [ubnt] | | [logo] 3V3 * | | TX * | | RX * | | GND * | | | | * | | * | | * | | * | | 0 | | 0 | | | | | Installation 1. Connect to serial header on device 2. Power on device and enter uboot console 3. Set up tftp server serving an openwrt initramfs build 4. Load initramfs build using the command tftpboot in the uboot cli 5. Boot the loaded image using the command bootm 6. Copy squashfs openwrt sysupgrade build to the booted device 7. Use mtd to write sysupgrade to partition "firmware" 8. Reboot and enjoy Signed-off-by: Tobias Schramm <tobleminer@gmail.com>
2018-09-04 00:08:01 +00:00
endef
TARGET_DEVICES += ubnt_nanostation-ac
ath79: Add support for Ubiquiti NanoStation AC loco Atheros AR9342, 16 MB flash, 64 MB RAM Successor to the old NanoStation M5 loco with AC wireless. Includes a mac80211 patch for ath10k_pci because Ubiquiti uses a Ubiquiti branded and customized QCA988X with vendor id 0777 and device id 11ac for AC wireless. Installation 1. Connect to serial header on device (8N1 115200) 2. Power on device and enter uboot console 3. Set up tftp server serving an openwrt initramfs build 4. Load initramfs build using the command tftpboot in the uboot cli 5. Boot the loaded image using the command bootm 6. Copy squashfs openwrt sysupgrade build to the booted device 7. Use mtd to write sysupgrade to partition "firmware" 8. Reboot and enjoy Signed-off-by: Tobias Schramm <tobleminer@gmail.com>
2018-01-23 10:36:41 +00:00
define Device/ubnt_nanostation-ac-loco
$(Device/ubnt-wa)
ath79: split DEVICE_TITLE in multiple variables This allows the definition of DEVICE_VENDOR, DEVICE_MODEL and DEVICE_VARIANT. All three are merged together to look the same as the current DEVICE_TITLE. Also, if DEVICE_TITLE is set it's directly used as a *fallback* for devices which weren't upgraded yet. This is based on the work of @sudhanshu16. The motivation is to create JSON files based on provided metadata, needing clear differentiation between vendor, model and revision. Signed-off-by: Paul Spooren <mail@aparcar.org>
2019-06-16 19:34:46 +00:00
DEVICE_MODEL := Nanostation AC loco
ath79: use ath10k-ct-smallbuffers for 64 MiB devices Signed-off-by: Paul Fertser <fercerpav@gmail.com>
2019-12-22 20:05:13 +00:00
DEVICE_PACKAGES += kmod-ath10k-ct-smallbuffers ath10k-firmware-qca988x-ct
ath79: Add support for Ubiquiti NanoStation AC loco Atheros AR9342, 16 MB flash, 64 MB RAM Successor to the old NanoStation M5 loco with AC wireless. Includes a mac80211 patch for ath10k_pci because Ubiquiti uses a Ubiquiti branded and customized QCA988X with vendor id 0777 and device id 11ac for AC wireless. Installation 1. Connect to serial header on device (8N1 115200) 2. Power on device and enter uboot console 3. Set up tftp server serving an openwrt initramfs build 4. Load initramfs build using the command tftpboot in the uboot cli 5. Boot the loaded image using the command bootm 6. Copy squashfs openwrt sysupgrade build to the booted device 7. Use mtd to write sysupgrade to partition "firmware" 8. Reboot and enjoy Signed-off-by: Tobias Schramm <tobleminer@gmail.com>
2018-01-23 10:36:41 +00:00
endef
TARGET_DEVICES += ubnt_nanostation-ac-loco
ath79: add support for Ubiquiti NanoStation Loco M (XW) This commit adds support for the NanoStation Loco M2/M5 XW devices on the ath79 target (support was long ago available on ar71xx). Specifications: - AR9342 SoC @ 535 MHz - 64 MB RAM - 8 MB SPI flash - 1x 10/100 Mbps Ethernet, 24 Vdc PoE-in - AR8032 switch - 2T2R 5 GHz radio, 22 dBm - 13 dBi built-in antenna - POWER/LAN green LEDs - 4x RSSI LEDs (red, orange, green, green) - UART (115200 8N1) on PCB Flashing via TFTP: - Use a pointy tool (e.g., pen cap, paper clip) and keep the reset button on the device or on the PoE supply pressed - Power on the device via PoE (keep reset button pressed) - Keep pressing until LEDs flash alternatively LED1+LED3 => LED2+LED4 => LED1+LED3, etc. - Release reset button - The device starts a TFTP server at 192.168.1.20 - Set a static IP on the computer (e.g., 192.168.1.21/24) - Upload via tftp the factory image: $ tftp 192.168.1.20 tftp> bin tftp> trace tftp> put openwrt-ath79-generic-xxxxx-ubnt_nanostation-loco-m-xw-squashfs-factory.bin Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
2019-09-18 13:17:56 +00:00
define Device/ubnt_nanostation-loco-m-xw
$(Device/ubnt-xw)
DEVICE_MODEL := Nanostation Loco M
DEVICE_PACKAGES += rssileds
SUPPORTED_DEVICES += loco-m-xw
endef
TARGET_DEVICES += ubnt_nanostation-loco-m-xw
ath79: sort device definitions in image/* This applies alphabetic sorting to devices in image/* files. For certain cases, this patch deviates from strict sorting, e.g. to ensure that v10 comes after v9. While at it, fix an indent and remove some useless empty lines. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-08-22 12:34:45 +00:00
define Device/ubnt_nanostation-m-xw
$(Device/ubnt-xw)
DEVICE_MODEL := Nanostation M
ath79: include rssileds package for ubnt devices with LEDs Some Ubiquiti devices had the RSSI LEDs configured in 01_leds but were missing the rssileds package, while others that don't have RSSI LEDS had the package included. This commit includes the rssileds package only for those devices that need it. Tested on a NanoStation M XW. Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
2019-11-13 15:18:59 +00:00
DEVICE_PACKAGES += rssileds
ath79: sort device definitions in image/* This applies alphabetic sorting to devices in image/* files. For certain cases, this patch deviates from strict sorting, e.g. to ensure that v10 comes after v9. While at it, fix an indent and remove some useless empty lines. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-08-22 12:34:45 +00:00
SUPPORTED_DEVICES += nanostation-m-xw
endef
TARGET_DEVICES += ubnt_nanostation-m-xw
ath79: add support for Ubiquiti PowerBeam 5AC 500 The Ubiquiti PowerBeam 5AC 500 (PBE-5AC-500) is an outdoor 802.11ac 5 GHz bridge with a radio feed and a dish antenna. Specifications: - SoC: Qualcomm Atheros QCA9558 - RAM: 128 MB DDR2 - Flash: 16 MB SPI NOR (mx25l12805d) - Ethernet: 1x 10/100/1000 Mbps Atheros 8031, 24 Vdc PoE-in - WiFi 5 GHz: QCA988x HW2.0 Ubiquiti target 0x4100016c chip_id 0x043222ff - Buttons: 1x (reset) - LEDs: 1x power, 1x Ethernet, 4x RSSI, all blue - UART: not tested Not supported: - RSSI LEDs (probably through 74HC595 chip) Installation from stock airOS firmware: - Follow instructions for XC-type Ubiquiti devices on OpenWrt wiki at https://openwrt.org/toh/ubiquiti/common Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
2020-04-24 00:22:44 +00:00
define Device/ubnt_powerbeam-5ac-500
$(Device/ubnt-xc)
SOC := qca9558
DEVICE_MODEL := PowerBeam 5AC
DEVICE_VARIANT := 500
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca988x-ct
endef
TARGET_DEVICES += ubnt_powerbeam-5ac-500
ath79: add support for Ubiquiti PowerBeam 5AC Gen2 The Ubiquiti PowerBeam 5AC Gen 2 (PBE-5AC-Gen2) is an outdoor 802.11ac 5 GHz bridge with a radio feed and a dish antenna. The device is hardware-compatible with the LiteBeam AC Gen2, plus the 4 extra LEDs. Specifications: - SoC: Qualcomm Atheros AR9342 rev 2 - RAM: 64 MB DDR2 - Flash: 16 MB SPI NOR (mx25l12805d) - Ethernet: 1x 10/100/1000 Mbps Atheros 8035, 24 Vdc PoE-in - WiFi 5 GHz: QCA988x HW2.0 Ubiquiti target 0x4100016c chip_id 0x043222ff - WiFi 2.4 GHz: Atheros AR9340 (SoC-based) - Buttons: 1x (reset) - LEDs: 1x power, 1x Ethernet, 4x RSSI via GPIO. All blue. - UART: not tested Installation from stock airOS firmware: - Follow instructions for WA-type Ubiquiti devices on OpenWrt wiki Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net> [changed device name in commit title] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-03-12 10:37:10 +00:00
define Device/ubnt_powerbeam-5ac-gen2
$(Device/ubnt-wa)
DEVICE_MODEL := PowerBeam 5AC
DEVICE_VARIANT := Gen2
DEVICE_PACKAGES := kmod-ath10k-ct-smallbuffers ath10k-firmware-qca988x-ct rssileds
endef
TARGET_DEVICES += ubnt_powerbeam-5ac-gen2
ath79: add support for Ubiquiti PowerBeam M2 (XW) This patch adds support for the Ubiquiti PowerBeam M2 (XW), e.g. PBE-M2-400, a 802.11n wireless with a feed+dish form factor. This device was previously supported by the ar71xx loco-m-xw firmware. Specifications: - Atheros AR9342 SoC - 64 MB RAM - 8 MB SPI flash - 1x 10/100 Mbps Ethernet port, 24 Vdc PoE-in - Power and LAN green LEDs - 4x RSSI LEDs (red, orange, green, green) - UART (115200 8N1) Flashing via stock GUI: - Downgrade to AirOS v5.5.x (latest available is 5.5.10-u2) first (see https://openwrt.org/toh/ubiquiti/powerbeam installation instructions) - Upload the factory image via AirOS web GUI. Flashing via TFTP: - Use a pointy tool (e.g., unbent paperclip) to keep the reset button pressed. - Power on the device (keep reset button pressed). - Keep pressing until LEDs flash alternatively LED1+LED3 => LED2+LED4 => LED1+LED3, etc. - Release reset button. - The device starts a TFTP server at 192.168.1.20. - Set a static IP on the computer (e.g., 192.168.1.21/24). - Upload via tftp the factory image: $ tftp 192.168.1.20 tftp> bin tftp> trace tftp> put openwrt-ath79-generic-ubnt_powerbeam-m2-xw-squashfs-factory.bin WARNING: so far, no non-destructive method has been discovered for opening the enclosure to reach the serial console. Internal photos are available here: https://fcc.io/SWX-NBM2HP Signed-off-by: Russell Senior <russell@personaltelco.net>
2021-08-13 05:57:41 +00:00
define Device/ubnt_powerbeam-m2-xw
$(Device/ubnt-xw)
DEVICE_MODEL := PowerBeam M2
DEVICE_PACKAGES += rssileds
SUPPORTED_DEVICES += loco-m-xw
endef
TARGET_DEVICES += ubnt_powerbeam-m2-xw
ath79: rename Ubiquiti PowerBeam M (XW) to PowerBeam M5 (XW) The commit [1] added support for Ubiquiti PowerBeam M (XW), tested on the PBE-M5-400. But, it turns out the PBE-M2-400 has a different ethernet configuration, so make the support specific to the m5 version in anticipation of adding specific support for the m2 in a separate commit. [1] 12eb5b2384a6 ("ath79: add support for Ubiquiti PowerBeam M (XW)") Signed-off-by: Russell Senior <russell@personaltelco.net> [fix model name in DTS, format commit reference in commit message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-08-13 05:57:39 +00:00
define Device/ubnt_powerbeam-m5-xw
ath79: add support for Ubiquiti PowerBeam M (XW) This patch adds support for the Ubiquiti PowerBeam M (XW), e.g. PBE-M5-400, a 802.11n wireless with a feed+dish form factor. This device was previously supported by the ar71xx loco-m-xw firmware. Specifications: - Atheros AR9342 SoC - 64 MB RAM - 8 MB SPI flash - 1x 10/100 Mbps Ethernet port, 24 Vdc PoE-in - Power and LAN green LEDs - 4x RSSI LEDs (red, orange, green, green) - UART (115200 8N1) Flashing via stock GUI: - Downgrade to AirOS v5.5.x (latest available is 5.5.10-u2) first (see https://openwrt.org/toh/ubiquiti/powerbeam installation instructions) - Upload the factory image via AirOS web GUI. Flashing via TFTP: - Use a pointy tool (e.g., unbent paperclip) to keep the reset button pressed. - Power on the device (keep reset button pressed). - Keep pressing until LEDs flash alternatively LED1+LED3 => LED2+LED4 => LED1+LED3, etc. - Release reset button. - The device starts a TFTP server at 192.168.1.20. - Set a static IP on the computer (e.g., 192.168.1.21/24). - Upload via tftp the factory image: $ tftp 192.168.1.20 tftp> bin tftp> trace tftp> put openwrt-ath79-generic-xxxxx-ubnt_powerbeam-m-xw-squashfs-factory.bin WARNING: so far, no non-destructive method has been discovered for opening the enclosure to reach the serial console. Internal photos are available here: https://fcc.io/SWX-NBM5HP Signed-off-by: Russell Senior <russell@personaltelco.net>
2021-06-05 00:27:48 +00:00
$(Device/ubnt-xw)
ath79: rename Ubiquiti PowerBeam M (XW) to PowerBeam M5 (XW) The commit [1] added support for Ubiquiti PowerBeam M (XW), tested on the PBE-M5-400. But, it turns out the PBE-M2-400 has a different ethernet configuration, so make the support specific to the m5 version in anticipation of adding specific support for the m2 in a separate commit. [1] 12eb5b2384a6 ("ath79: add support for Ubiquiti PowerBeam M (XW)") Signed-off-by: Russell Senior <russell@personaltelco.net> [fix model name in DTS, format commit reference in commit message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-08-13 05:57:39 +00:00
DEVICE_MODEL := PowerBeam M5
ath79: add support for Ubiquiti PowerBeam M (XW) This patch adds support for the Ubiquiti PowerBeam M (XW), e.g. PBE-M5-400, a 802.11n wireless with a feed+dish form factor. This device was previously supported by the ar71xx loco-m-xw firmware. Specifications: - Atheros AR9342 SoC - 64 MB RAM - 8 MB SPI flash - 1x 10/100 Mbps Ethernet port, 24 Vdc PoE-in - Power and LAN green LEDs - 4x RSSI LEDs (red, orange, green, green) - UART (115200 8N1) Flashing via stock GUI: - Downgrade to AirOS v5.5.x (latest available is 5.5.10-u2) first (see https://openwrt.org/toh/ubiquiti/powerbeam installation instructions) - Upload the factory image via AirOS web GUI. Flashing via TFTP: - Use a pointy tool (e.g., unbent paperclip) to keep the reset button pressed. - Power on the device (keep reset button pressed). - Keep pressing until LEDs flash alternatively LED1+LED3 => LED2+LED4 => LED1+LED3, etc. - Release reset button. - The device starts a TFTP server at 192.168.1.20. - Set a static IP on the computer (e.g., 192.168.1.21/24). - Upload via tftp the factory image: $ tftp 192.168.1.20 tftp> bin tftp> trace tftp> put openwrt-ath79-generic-xxxxx-ubnt_powerbeam-m-xw-squashfs-factory.bin WARNING: so far, no non-destructive method has been discovered for opening the enclosure to reach the serial console. Internal photos are available here: https://fcc.io/SWX-NBM5HP Signed-off-by: Russell Senior <russell@personaltelco.net>
2021-06-05 00:27:48 +00:00
DEVICE_PACKAGES += rssileds
SUPPORTED_DEVICES += loco-m-xw
endef
ath79: rename Ubiquiti PowerBeam M (XW) to PowerBeam M5 (XW) The commit [1] added support for Ubiquiti PowerBeam M (XW), tested on the PBE-M5-400. But, it turns out the PBE-M2-400 has a different ethernet configuration, so make the support specific to the m5 version in anticipation of adding specific support for the m2 in a separate commit. [1] 12eb5b2384a6 ("ath79: add support for Ubiquiti PowerBeam M (XW)") Signed-off-by: Russell Senior <russell@personaltelco.net> [fix model name in DTS, format commit reference in commit message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-08-13 05:57:39 +00:00
TARGET_DEVICES += ubnt_powerbeam-m5-xw
ath79: add support for Ubiquiti PowerBeam M (XW) This patch adds support for the Ubiquiti PowerBeam M (XW), e.g. PBE-M5-400, a 802.11n wireless with a feed+dish form factor. This device was previously supported by the ar71xx loco-m-xw firmware. Specifications: - Atheros AR9342 SoC - 64 MB RAM - 8 MB SPI flash - 1x 10/100 Mbps Ethernet port, 24 Vdc PoE-in - Power and LAN green LEDs - 4x RSSI LEDs (red, orange, green, green) - UART (115200 8N1) Flashing via stock GUI: - Downgrade to AirOS v5.5.x (latest available is 5.5.10-u2) first (see https://openwrt.org/toh/ubiquiti/powerbeam installation instructions) - Upload the factory image via AirOS web GUI. Flashing via TFTP: - Use a pointy tool (e.g., unbent paperclip) to keep the reset button pressed. - Power on the device (keep reset button pressed). - Keep pressing until LEDs flash alternatively LED1+LED3 => LED2+LED4 => LED1+LED3, etc. - Release reset button. - The device starts a TFTP server at 192.168.1.20. - Set a static IP on the computer (e.g., 192.168.1.21/24). - Upload via tftp the factory image: $ tftp 192.168.1.20 tftp> bin tftp> trace tftp> put openwrt-ath79-generic-xxxxx-ubnt_powerbeam-m-xw-squashfs-factory.bin WARNING: so far, no non-destructive method has been discovered for opening the enclosure to reach the serial console. Internal photos are available here: https://fcc.io/SWX-NBM5HP Signed-off-by: Russell Senior <russell@personaltelco.net>
2021-06-05 00:27:48 +00:00
ath79: Support for Ubiquiti Rocket 5AC Lite The Ubiquiti Rocket 5AC Lite (R5AC-Lite) is an outdoor router. Specifications: - SoC: Qualcomm Atheros QCA9558 - RAM: 128 MB - Flash: 16 MB SPI - Ethernet: 1x 10/100/1000 Mbps - WiFi 5 GHz: QCA988x - Buttons: 1x (reset) - LEDs: 1x power, 1x Ethernet, 4x RSSI Installation: - Instructions for XC-type Ubiquiti: https://openwrt.org/toh/ubiquiti/common Signed-off-by: Nick Hainke <vincent@systemli.org>
2021-04-25 20:41:46 +00:00
define Device/ubnt_rocket-5ac-lite
$(Device/ubnt-xc)
SOC := qca9558
DEVICE_MODEL := Rocket 5AC
DEVICE_VARIANT := Lite
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca988x-ct
endef
TARGET_DEVICES += ubnt_rocket-5ac-lite
ath79: sort device definitions in image/* This applies alphabetic sorting to devices in image/* files. For certain cases, this patch deviates from strict sorting, e.g. to ensure that v10 comes after v9. While at it, fix an indent and remove some useless empty lines. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-08-22 12:34:45 +00:00
define Device/ubnt_routerstation_common
treewide: use wpad-basic-wolfssl as default In order to support SAE/WPA3-Personal in default images. Replace almost all occurencies of wpad-basic and wpad-mini with wpad-basic-wolfssl for consistency. Keep out ar71xx from the list as it won't be in the next release and would only make backports harder. Build-tested (build-bot settings): ath79: generic, ramips: mt7620/mt76x8/rt305x, lantiq: xrx200/xway, sunxi: a53 Signed-off-by: Petr Štetiar <ynezz@true.cz> [rebase, extend commit message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-27 10:30:41 +00:00
DEVICE_PACKAGES := -kmod-ath9k -wpad-basic-wolfssl -uboot-envtools kmod-usb-ohci \
ath79: harmonize line breaks in image Makefiles This harmonizes the line wrapping in image Makefile device definitions, as those are frequently copy-pasted and are a common subject of review comments. Having the treatment unifying should reduce the cases where adjustment is necessary afterwards. Harmonization is achieved by consistently (read "strictly") applying certain rules: - Never put more than 80 characters into one line - Fill lines up (do not break after 40 chars because of ...) - Use one tab for indent after wrapping by "\" - Only break after pipe "|" for IMAGE variables Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-12-19 19:42:19 +00:00
kmod-usb2 fconfig
ath79: sort device definitions in image/* This applies alphabetic sorting to devices in image/* files. For certain cases, this patch deviates from strict sorting, e.g. to ensure that v10 comes after v9. While at it, fix an indent and remove some useless empty lines. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-08-22 12:34:45 +00:00
DEVICE_VENDOR := Ubiquiti
ath79: rename ATH_SOC to SOC This replaces ATH_SOC by the newly introduced common SOC device variable. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-12-20 00:12:42 +00:00
SOC := ar7161
ath79: switch some RedBoot based devices to OKLI loader After the kernel has switched version to 5.10, JA76PF2 and RouterStations lost the capability to sysupgrade the OpenWrt version. The cause is the lack of porting the patches responsible for partial flash erase block writing and these boards FIS directory and RedBoot config partitions share the same erase block. Because of that the FIS directory can't be updated to accommodate kernel/rootfs partition size changes. This could be remedied by bootloader update, but it is very intrusive and could potentially lead to non-trivial recovery procedure, if something went wrong. The less difficult option is to use OpenWrt kernel loader, which will let us use static partition sizes and employ mtd splitter to dynamically adjust kernel and rootfs partition sizes. On sysupgrade from ath79 19.07 or 21.02 image, which still let to modify FIS directory, the loader will be written to kernel partition, while the kernel+rootfs to rootfs partition. The caveats are: * image format changes, no possible upgrade from ar71xx target images * downgrade to any older OpenWrt version will require TFTP recovery or usage of bootloader command line interface To downgrade to 19.07 or 21.02, or to upgrade if one is already on OpenWrt with kernel 5.10, for RouterStations use TFTP recovery procedure. For JA76PF2 use instructions from this commit message: commit 0cc87b3bacee ("ath79: image: disable sysupgrade images for routerstations and ja76pf2"), replacing kernel image with loader (loader.bin suffix) and rootfs image with firmware (firmware.bin suffix). Fixes: b10d6044599d ("kernel: add linux 5.10 support") Fixes: 15aa53d7ee65 ("ath79: switch to Kernel 5.10") Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com> (mkubntimage was moved to generic-ubnt.mk) Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-06-07 13:58:27 +00:00
LOADER_TYPE := bin
LOADER_FLASH_OFFS := 0x50000
COMPILE := loader-$(1).bin
COMPILE/loader-$(1).bin := loader-okli-compile | lzma | pad-to 128k
IMAGE_SIZE := 16000k
ath79: restore sysupgrade support for ja76pf2 and routerstations Because the bug described in FS#2428 has been fixed with bf2870c1d9e1 ("kernel: fix mtd partition erase < parent_erasesize writes") these devices can now safely do sysupgrade. Restore sysupgrade support disabled in: 0cc87b3bacee ("ath79: image: disable sysupgrade images for routerstations and ja76pf2") cc5256a8bfa0 ("ath79: base-files: disable sysupgrade for routerstations and ja76pf2") Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com> [move Build block, remove check-size argument, wrap sysupgrade line, make commit message easier to read] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-12-01 17:30:27 +00:00
IMAGES += factory.bin
ath79: switch some RedBoot based devices to OKLI loader After the kernel has switched version to 5.10, JA76PF2 and RouterStations lost the capability to sysupgrade the OpenWrt version. The cause is the lack of porting the patches responsible for partial flash erase block writing and these boards FIS directory and RedBoot config partitions share the same erase block. Because of that the FIS directory can't be updated to accommodate kernel/rootfs partition size changes. This could be remedied by bootloader update, but it is very intrusive and could potentially lead to non-trivial recovery procedure, if something went wrong. The less difficult option is to use OpenWrt kernel loader, which will let us use static partition sizes and employ mtd splitter to dynamically adjust kernel and rootfs partition sizes. On sysupgrade from ath79 19.07 or 21.02 image, which still let to modify FIS directory, the loader will be written to kernel partition, while the kernel+rootfs to rootfs partition. The caveats are: * image format changes, no possible upgrade from ar71xx target images * downgrade to any older OpenWrt version will require TFTP recovery or usage of bootloader command line interface To downgrade to 19.07 or 21.02, or to upgrade if one is already on OpenWrt with kernel 5.10, for RouterStations use TFTP recovery procedure. For JA76PF2 use instructions from this commit message: commit 0cc87b3bacee ("ath79: image: disable sysupgrade images for routerstations and ja76pf2"), replacing kernel image with loader (loader.bin suffix) and rootfs image with firmware (firmware.bin suffix). Fixes: b10d6044599d ("kernel: add linux 5.10 support") Fixes: 15aa53d7ee65 ("ath79: switch to Kernel 5.10") Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com> (mkubntimage was moved to generic-ubnt.mk) Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-06-07 13:58:27 +00:00
IMAGE/factory.bin := append-kernel | uImage lzma -M 0x4f4b4c49 | pad-to $$$$(BLOCKSIZE) | \
append-rootfs | pad-rootfs | pad-to $$$$(BLOCKSIZE) | \
mkubntimage $$$$(KDIR)/loader-$(1).bin | check-size
IMAGE/sysupgrade.bin := append-kernel | uImage lzma -M 0x4f4b4c49 | pad-to $$$$(BLOCKSIZE) | \
append-rootfs | pad-rootfs | pad-to $$$$(BLOCKSIZE) | check-size | \
sysupgrade-tar kernel=$$$$(KDIR)/loader-$(1).bin rootfs=$$$$@ | append-metadata
KERNEL := kernel-bin | append-dtb | lzma
ath79: sort device definitions in image/* This applies alphabetic sorting to devices in image/* files. For certain cases, this patch deviates from strict sorting, e.g. to ensure that v10 comes after v9. While at it, fix an indent and remove some useless empty lines. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-08-22 12:34:45 +00:00
KERNEL_INITRAMFS := kernel-bin | append-dtb
ath79: switch some RedBoot based devices to OKLI loader After the kernel has switched version to 5.10, JA76PF2 and RouterStations lost the capability to sysupgrade the OpenWrt version. The cause is the lack of porting the patches responsible for partial flash erase block writing and these boards FIS directory and RedBoot config partitions share the same erase block. Because of that the FIS directory can't be updated to accommodate kernel/rootfs partition size changes. This could be remedied by bootloader update, but it is very intrusive and could potentially lead to non-trivial recovery procedure, if something went wrong. The less difficult option is to use OpenWrt kernel loader, which will let us use static partition sizes and employ mtd splitter to dynamically adjust kernel and rootfs partition sizes. On sysupgrade from ath79 19.07 or 21.02 image, which still let to modify FIS directory, the loader will be written to kernel partition, while the kernel+rootfs to rootfs partition. The caveats are: * image format changes, no possible upgrade from ar71xx target images * downgrade to any older OpenWrt version will require TFTP recovery or usage of bootloader command line interface To downgrade to 19.07 or 21.02, or to upgrade if one is already on OpenWrt with kernel 5.10, for RouterStations use TFTP recovery procedure. For JA76PF2 use instructions from this commit message: commit 0cc87b3bacee ("ath79: image: disable sysupgrade images for routerstations and ja76pf2"), replacing kernel image with loader (loader.bin suffix) and rootfs image with firmware (firmware.bin suffix). Fixes: b10d6044599d ("kernel: add linux 5.10 support") Fixes: 15aa53d7ee65 ("ath79: switch to Kernel 5.10") Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com> (mkubntimage was moved to generic-ubnt.mk) Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-06-07 13:58:27 +00:00
DEVICE_COMPAT_VERSION := 2.0
DEVICE_COMPAT_MESSAGE := Partition design has changed compared to older versions (19.07 and 21.02) \
due to kernel drivers restrictions. Upgrade via sysupgrade mechanism is one way operation. \
Downgrading OpenWrt version will involve usage of TFTP recovery or bootloader command line interface.
ath79: sort device definitions in image/* This applies alphabetic sorting to devices in image/* files. For certain cases, this patch deviates from strict sorting, e.g. to ensure that v10 comes after v9. While at it, fix an indent and remove some useless empty lines. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-08-22 12:34:45 +00:00
endef
define Device/ubnt_routerstation
$(Device/ubnt_routerstation_common)
DEVICE_MODEL := RouterStation
UBNT_BOARD := RS
UBNT_TYPE := RSx
UBNT_CHIP := ar7100
DEVICE_PACKAGES += -swconfig
endef
TARGET_DEVICES += ubnt_routerstation
define Device/ubnt_routerstation-pro
$(Device/ubnt_routerstation_common)
DEVICE_MODEL := RouterStation Pro
UBNT_BOARD := RSPRO
UBNT_TYPE := RSPRO
UBNT_CHIP := ar7100pro
endef
TARGET_DEVICES += ubnt_routerstation-pro
ath79: fix dts files Add the SoC compatible to the individual dts files. Rename the dts files to match the common pattern. Remove dts files wich aren't used and no image in ar71xx exists. Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-05-08 05:22:38 +00:00
define Device/ubnt_unifi
ath79: add new OF only target for QCA MIPS silicon This target aims to replace ar71xx mid-term. The big part that is still missing is making the MMIO/AHB wifi work using OF. NAND and mikrotik subtargets will follow. Signed-off-by: John Crispin <john@phrozen.org>
2018-05-06 08:20:11 +00:00
$(Device/ubnt-bz)
ath79: change Ubiquiti UniFi AP model name to include "AP" While it hasn't always been clear whether the "AP" is part of the model name on the Ubiquiti website, we include it for all other pre-AC variants (AP Pro and the AP Outdoor+). Add it to the original UniFi AP as well for consistency. Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2022-03-24 08:26:01 +00:00
DEVICE_MODEL := UniFi AP
ath79: add and enforce image metadata Add metadata to images and make the metdata mandatory. Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-05-07 20:41:04 +00:00
SUPPORTED_DEVICES += unifi
ath79: add new OF only target for QCA MIPS silicon This target aims to replace ar71xx mid-term. The big part that is still missing is making the MMIO/AHB wifi work using OF. NAND and mikrotik subtargets will follow. Signed-off-by: John Crispin <john@phrozen.org>
2018-05-06 08:20:11 +00:00
endef
ath79: fix dts files Add the SoC compatible to the individual dts files. Rename the dts files to match the common pattern. Remove dts files wich aren't used and no image in ar71xx exists. Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-05-08 05:22:38 +00:00
TARGET_DEVICES += ubnt_unifi
ath79: add ubiquiti unifi ap ac lite/lr Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
2018-06-05 12:38:02 +00:00
ath79: sync naming of Ubiquiti devices Use a Unifi AC Lite board-/image name consistent with other Ubiquiti devices. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2018-06-27 10:10:33 +00:00
define Device/ubnt_unifiac
ath79: split DEVICE_TITLE in multiple variables This allows the definition of DEVICE_VENDOR, DEVICE_MODEL and DEVICE_VARIANT. All three are merged together to look the same as the current DEVICE_TITLE. Also, if DEVICE_TITLE is set it's directly used as a *fallback* for devices which weren't upgraded yet. This is based on the work of @sudhanshu16. The motivation is to create JSON files based on provided metadata, needing clear differentiation between vendor, model and revision. Signed-off-by: Paul Spooren <mail@aparcar.org>
2019-06-16 19:34:46 +00:00
DEVICE_VENDOR := Ubiquiti
ath79: rename ATH_SOC to SOC This replaces ATH_SOC by the newly introduced common SOC device variable. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-12-20 00:12:42 +00:00
SOC := qca9563
ath79: add ubiquiti unifi ap ac lite/lr Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
2018-06-05 12:38:02 +00:00
IMAGE_SIZE := 7744k
mac80211: make ath10k-ct the default ath10k We select ath10k-ct by default, but it is still possible to build the upstream version. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: John Crispin <john@phrozen.org>
2018-09-05 12:51:44 +00:00
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca988x-ct
ath79: add ubiquiti unifi ap ac lite/lr Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
2018-06-05 12:38:02 +00:00
endef
ath79: sync naming of Ubiquiti devices Use a Unifi AC Lite board-/image name consistent with other Ubiquiti devices. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2018-06-27 10:10:33 +00:00
define Device/ubnt_unifiac-lite
$(Device/ubnt_unifiac)
ath79: harmonize model names for Ubiquiti devices This harmonizes the model names for the ath79 Ubiquiti devices by applying a few minor cosmetic adjustments: - Removes hyphens where they are not found in the product names (Ubiquiti uses hyphens only for the abbreviated version names like UAP-AC-PRO which we don't use anyway.) - Add (XM) suffix for DTS model strings to help with distinguishing them from their XW counterparts. - Remove DEVICE_VARIANT for LAP-120 which actually was an alternate device name. - Generally make DTS model names and those from generic-ubnt.mk more consistent. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-15 16:41:57 +00:00
DEVICE_MODEL := UniFi AC Lite
ath79: ubnt: drop swconfig on ac-{lite,lr,mesh} These don't have switches that could be configured using swconfig. Signed-off-by: Martin Weinelt <hexa@darmstadt.ccc.de>
2022-04-17 13:56:53 +00:00
DEVICE_PACKAGES += -swconfig
ath79: correct ar71xx boardname for UniFi AC Lite This corrects the additional boardname for the image metadata to the one used in ar71xx. The previously present additional entry was never used on a running system. Reviewed-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Signed-off-by: David Bauer <mail@david-bauer.net>
2019-10-14 09:16:54 +00:00
SUPPORTED_DEVICES += unifiac-lite
ath79: add ubiquiti unifi ap ac lite/lr Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
2018-06-05 12:38:02 +00:00
endef
ath79: sync naming of Ubiquiti devices Use a Unifi AC Lite board-/image name consistent with other Ubiquiti devices. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2018-06-27 10:10:33 +00:00
TARGET_DEVICES += ubnt_unifiac-lite
ath79: add support for Ubiquiti UniFi AC-Pro rework the dts to a common unifi-ac dtsi pro network is connected via phy0 and has usb ports lite network is connected via phy4 without usb ports Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
2018-06-26 07:30:46 +00:00
ath79: add support for UniFi AC-LR The Unifi AC-LR has identical hardware to the Unifi AC-Lite. The antenna setup is different according to the vendor, which explains the thicker enclosure. Therefore, it is helpful to know the exact device variant, instead of having "Ubiquiti UniFi-AC-LITE/LR". Signed-off-by: Andreas Ziegler <dev@andreas-ziegler.de> [fix legacy name in commit message; add old boardname to SUPPORTED_DEVICES] Signed-off-by: David Bauer <mail@david-bauer.net>
2019-10-06 17:48:34 +00:00
define Device/ubnt_unifiac-lr
$(Device/ubnt_unifiac)
ath79: harmonize model names for Ubiquiti devices This harmonizes the model names for the ath79 Ubiquiti devices by applying a few minor cosmetic adjustments: - Removes hyphens where they are not found in the product names (Ubiquiti uses hyphens only for the abbreviated version names like UAP-AC-PRO which we don't use anyway.) - Add (XM) suffix for DTS model strings to help with distinguishing them from their XW counterparts. - Remove DEVICE_VARIANT for LAP-120 which actually was an alternate device name. - Generally make DTS model names and those from generic-ubnt.mk more consistent. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-15 16:41:57 +00:00
DEVICE_MODEL := UniFi AC LR
ath79: ubnt: drop swconfig on ac-{lite,lr,mesh} These don't have switches that could be configured using swconfig. Signed-off-by: Martin Weinelt <hexa@darmstadt.ccc.de>
2022-04-17 13:56:53 +00:00
DEVICE_PACKAGES += -swconfig
ath79: add support for UniFi AC-LR The Unifi AC-LR has identical hardware to the Unifi AC-Lite. The antenna setup is different according to the vendor, which explains the thicker enclosure. Therefore, it is helpful to know the exact device variant, instead of having "Ubiquiti UniFi-AC-LITE/LR". Signed-off-by: Andreas Ziegler <dev@andreas-ziegler.de> [fix legacy name in commit message; add old boardname to SUPPORTED_DEVICES] Signed-off-by: David Bauer <mail@david-bauer.net>
2019-10-06 17:48:34 +00:00
SUPPORTED_DEVICES += unifiac-lite ubnt,unifiac-lite
endef
TARGET_DEVICES += ubnt_unifiac-lr
ath79: add support for Unifi AC Mesh The Unifi AC Mesh is equivalent to the Unifi AC Lite. However, for setting certain parameters with the flashed device it is helpful that the devices know their variant (e.g. automatically setting antenna gain for the different antennas in Lite and Mesh). Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2018-06-27 12:33:40 +00:00
define Device/ubnt_unifiac-mesh
$(Device/ubnt_unifiac)
ath79: harmonize model names for Ubiquiti devices This harmonizes the model names for the ath79 Ubiquiti devices by applying a few minor cosmetic adjustments: - Removes hyphens where they are not found in the product names (Ubiquiti uses hyphens only for the abbreviated version names like UAP-AC-PRO which we don't use anyway.) - Add (XM) suffix for DTS model strings to help with distinguishing them from their XW counterparts. - Remove DEVICE_VARIANT for LAP-120 which actually was an alternate device name. - Generally make DTS model names and those from generic-ubnt.mk more consistent. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-15 16:41:57 +00:00
DEVICE_MODEL := UniFi AC Mesh
ath79: ubnt: drop swconfig on ac-{lite,lr,mesh} These don't have switches that could be configured using swconfig. Signed-off-by: Martin Weinelt <hexa@darmstadt.ccc.de>
2022-04-17 13:56:53 +00:00
DEVICE_PACKAGES += -swconfig
ath79: fix SUPPORTED_DEVICES not matching ar71xx board names Based on a script for comparison, this fixes (hopefully) all errors in SUPPORTED_DEVICES for ar71xx->ath79 upgrade. Devices where old string is removed as the device does not exist in ar71xx: - dlink_dir-859-a1 - tplink_archer-a7-v5 - tplink_cpe510-v3 Devices where string is changed because it did not match the board name in ar71xx: - tplink_tl-mr3220-v1 - tplink_tl-mr3420-v1 - tplink_tl-wr2543-v1 - tplink_tl-wr741nd-v4 - tplink_tl-wr841-v7 - ubnt_unifiac-mesh - ubnt_unifiac-mesh-pro - ubnt_unifiac-pro For this device, the correct string could not be found, but we could not determine the correct one. Thus, the string is removed for now: - tplink_tl-wr740n-v4 The script for checking this is quite simple (note that newer entries, i.e. ath79->ath79 upgrade, are displayed as missing): newpath=target/linux/ath79/image/ oldpath=target/linux/ar71xx/base-files/lib/ar71xx.sh for s in $(grep -roh "SUPPORTED_DEVICES.*" $newpath | sed 's/SUPPORTED_DEVICES *.= *//'); do found="Missing" grep -q -r "\"$s\"" $oldpath && found="Found" echo "$s: $found." done The errors might be filtered by appending 'grep "Missing"' to the script. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-01-23 14:42:48 +00:00
SUPPORTED_DEVICES += unifiac-lite
ath79: add support for Unifi AC Mesh The Unifi AC Mesh is equivalent to the Unifi AC Lite. However, for setting certain parameters with the flashed device it is helpful that the devices know their variant (e.g. automatically setting antenna gain for the different antennas in Lite and Mesh). Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2018-06-27 12:33:40 +00:00
endef
TARGET_DEVICES += ubnt_unifiac-mesh
ath79: add support for UniFi AC-Mesh Pro The Unifi AC-Mesh Pro has identical hardware to the Unifi AC-Pro except USB support. Furthermore for setting parameters like antenna gain it is helpful to know the exact device variant. Signed-off-by: Christoph Krapp <achterin@googlemail.com>
2018-07-02 12:39:54 +00:00
define Device/ubnt_unifiac-mesh-pro
$(Device/ubnt_unifiac)
ath79: harmonize model names for Ubiquiti devices This harmonizes the model names for the ath79 Ubiquiti devices by applying a few minor cosmetic adjustments: - Removes hyphens where they are not found in the product names (Ubiquiti uses hyphens only for the abbreviated version names like UAP-AC-PRO which we don't use anyway.) - Add (XM) suffix for DTS model strings to help with distinguishing them from their XW counterparts. - Remove DEVICE_VARIANT for LAP-120 which actually was an alternate device name. - Generally make DTS model names and those from generic-ubnt.mk more consistent. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-15 16:41:57 +00:00
DEVICE_MODEL := UniFi AC Mesh Pro
ath79: fix SUPPORTED_DEVICES not matching ar71xx board names Based on a script for comparison, this fixes (hopefully) all errors in SUPPORTED_DEVICES for ar71xx->ath79 upgrade. Devices where old string is removed as the device does not exist in ar71xx: - dlink_dir-859-a1 - tplink_archer-a7-v5 - tplink_cpe510-v3 Devices where string is changed because it did not match the board name in ar71xx: - tplink_tl-mr3220-v1 - tplink_tl-mr3420-v1 - tplink_tl-wr2543-v1 - tplink_tl-wr741nd-v4 - tplink_tl-wr841-v7 - ubnt_unifiac-mesh - ubnt_unifiac-mesh-pro - ubnt_unifiac-pro For this device, the correct string could not be found, but we could not determine the correct one. Thus, the string is removed for now: - tplink_tl-wr740n-v4 The script for checking this is quite simple (note that newer entries, i.e. ath79->ath79 upgrade, are displayed as missing): newpath=target/linux/ath79/image/ oldpath=target/linux/ar71xx/base-files/lib/ar71xx.sh for s in $(grep -roh "SUPPORTED_DEVICES.*" $newpath | sed 's/SUPPORTED_DEVICES *.= *//'); do found="Missing" grep -q -r "\"$s\"" $oldpath && found="Found" echo "$s: $found." done The errors might be filtered by appending 'grep "Missing"' to the script. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-01-23 14:42:48 +00:00
SUPPORTED_DEVICES += unifiac-pro
ath79: add support for UniFi AC-Mesh Pro The Unifi AC-Mesh Pro has identical hardware to the Unifi AC-Pro except USB support. Furthermore for setting parameters like antenna gain it is helpful to know the exact device variant. Signed-off-by: Christoph Krapp <achterin@googlemail.com>
2018-07-02 12:39:54 +00:00
endef
TARGET_DEVICES += ubnt_unifiac-mesh-pro
ath79: add support for Ubiquiti UniFi AC-Pro rework the dts to a common unifi-ac dtsi pro network is connected via phy0 and has usb ports lite network is connected via phy4 without usb ports Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
2018-06-26 07:30:46 +00:00
define Device/ubnt_unifiac-pro
$(Device/ubnt_unifiac)
ath79: harmonize model names for Ubiquiti devices This harmonizes the model names for the ath79 Ubiquiti devices by applying a few minor cosmetic adjustments: - Removes hyphens where they are not found in the product names (Ubiquiti uses hyphens only for the abbreviated version names like UAP-AC-PRO which we don't use anyway.) - Add (XM) suffix for DTS model strings to help with distinguishing them from their XW counterparts. - Remove DEVICE_VARIANT for LAP-120 which actually was an alternate device name. - Generally make DTS model names and those from generic-ubnt.mk more consistent. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-15 16:41:57 +00:00
DEVICE_MODEL := UniFi AC Pro
treewide: remove kmod-usb-core from DEVICE_PACKAGES This removes _all_ occurrences of kmod-usb-core from DEVICE_PACKAGES and similar variables. This package is pulled as dependency by one of the following packages in any case: - kmod-usb-chipidea - kmod-usb-dwc2 - kmod-usb-ledtrig-usbport - kmod-usb-ohci - kmod-usb2 - kmod-usb2-pci - kmod-usb3 Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> [remove kmod-usb-core from EnGenius ESR600] Signed-off-by: David Bauer <mail@david-bauer.net>
2019-09-22 10:06:25 +00:00
DEVICE_PACKAGES += kmod-usb2
ath79: fix SUPPORTED_DEVICES not matching ar71xx board names Based on a script for comparison, this fixes (hopefully) all errors in SUPPORTED_DEVICES for ar71xx->ath79 upgrade. Devices where old string is removed as the device does not exist in ar71xx: - dlink_dir-859-a1 - tplink_archer-a7-v5 - tplink_cpe510-v3 Devices where string is changed because it did not match the board name in ar71xx: - tplink_tl-mr3220-v1 - tplink_tl-mr3420-v1 - tplink_tl-wr2543-v1 - tplink_tl-wr741nd-v4 - tplink_tl-wr841-v7 - ubnt_unifiac-mesh - ubnt_unifiac-mesh-pro - ubnt_unifiac-pro For this device, the correct string could not be found, but we could not determine the correct one. Thus, the string is removed for now: - tplink_tl-wr740n-v4 The script for checking this is quite simple (note that newer entries, i.e. ath79->ath79 upgrade, are displayed as missing): newpath=target/linux/ath79/image/ oldpath=target/linux/ar71xx/base-files/lib/ar71xx.sh for s in $(grep -roh "SUPPORTED_DEVICES.*" $newpath | sed 's/SUPPORTED_DEVICES *.= *//'); do found="Missing" grep -q -r "\"$s\"" $oldpath && found="Found" echo "$s: $found." done The errors might be filtered by appending 'grep "Missing"' to the script. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-01-23 14:42:48 +00:00
SUPPORTED_DEVICES += unifiac-pro
ath79: add support for Ubiquiti UniFi AC-Pro rework the dts to a common unifi-ac dtsi pro network is connected via phy0 and has usb ports lite network is connected via phy4 without usb ports Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
2018-06-26 07:30:46 +00:00
endef
TARGET_DEVICES += ubnt_unifiac-pro
ath79: add support for Ubiquiti UniFi AP Pro This adds support for the Ubiquiti UniFi AP Pro to the ath79 target. The device was previously supported on the now removed ar71xx target. SoC Atheros AR9344 WiFi Atheros AR9344 & Atheros AR9280 ETH Atheros AR8327 RAM 128M DDR2 FLASH 16M SPI-NOR Installation ------------ Follow the Ubiquiti TFTP recovery procedure for this device. 1. Hold down the reset button while connecting power for 10 seconds. 2. Transfer the factory image via TFTP to the AP (192.168.1.20) 3. Wait 2 minutes for the AP to write the firmware to flash. The device will automatically reboot to OpenWrt. Signed-off-by: David Bauer <mail@david-bauer.net>
2020-09-11 16:32:05 +00:00
ath79: add support for Ubiquiti UniFi AP Outdoor+ Hardware -------- Atheros AR7241 16M SPI-NOR 64M DDR2 Atheros AR9283 2T2R b/g/n 2x Fast Ethernet (built-in) Installation ------------ Transfer the Firmware update to the device using SCP. Install using fwupdate.real -m <openwrt.bin> -d Signed-off-by: David Bauer <mail@david-bauer.net>
2020-12-09 21:18:43 +00:00
define Device/ubnt_unifi-ap-outdoor-plus
$(Device/ubnt-bz)
$(Device/ubnt-unifi-jffs2)
DEVICE_MODEL := UniFi AP Outdoor+
SUPPORTED_DEVICES += unifi-outdoor-plus
endef
TARGET_DEVICES += ubnt_unifi-ap-outdoor-plus
ath79: add support for Ubiquiti UniFi AP Pro This adds support for the Ubiquiti UniFi AP Pro to the ath79 target. The device was previously supported on the now removed ar71xx target. SoC Atheros AR9344 WiFi Atheros AR9344 & Atheros AR9280 ETH Atheros AR8327 RAM 128M DDR2 FLASH 16M SPI-NOR Installation ------------ Follow the Ubiquiti TFTP recovery procedure for this device. 1. Hold down the reset button while connecting power for 10 seconds. 2. Transfer the factory image via TFTP to the AP (192.168.1.20) 3. Wait 2 minutes for the AP to write the firmware to flash. The device will automatically reboot to OpenWrt. Signed-off-by: David Bauer <mail@david-bauer.net>
2020-09-11 16:32:05 +00:00
define Device/ubnt_unifi-ap-pro
ath79: add support for Ubiquiti UniFi AP Outdoor+ Hardware -------- Atheros AR7241 16M SPI-NOR 64M DDR2 Atheros AR9283 2T2R b/g/n 2x Fast Ethernet (built-in) Installation ------------ Transfer the Firmware update to the device using SCP. Install using fwupdate.real -m <openwrt.bin> -d Signed-off-by: David Bauer <mail@david-bauer.net>
2020-12-09 21:18:43 +00:00
$(Device/ubnt-unifi-jffs2)
ath79: add support for Ubiquiti UniFi AP Pro This adds support for the Ubiquiti UniFi AP Pro to the ath79 target. The device was previously supported on the now removed ar71xx target. SoC Atheros AR9344 WiFi Atheros AR9344 & Atheros AR9280 ETH Atheros AR8327 RAM 128M DDR2 FLASH 16M SPI-NOR Installation ------------ Follow the Ubiquiti TFTP recovery procedure for this device. 1. Hold down the reset button while connecting power for 10 seconds. 2. Transfer the factory image via TFTP to the AP (192.168.1.20) 3. Wait 2 minutes for the AP to write the firmware to flash. The device will automatically reboot to OpenWrt. Signed-off-by: David Bauer <mail@david-bauer.net>
2020-09-11 16:32:05 +00:00
SOC := ar9344
DEVICE_MODEL := UniFi AP Pro
UBNT_CHIP := ar934x
SUPPORTED_DEVICES += uap-pro
endef
TARGET_DEVICES += ubnt_unifi-ap-pro
Reference in New Issue Copy Permalink