ath79: add support for TP-Link TL-WR902AC v1
TP-Link TL-WR902AC v1 is a pocket-size, dual-band (AC750), successor of
TL-MR3020 (both devices use very similar enclosure, in same size). New
device is based on Qualcomm QCA9531 v2 + QCA9887. FCC ID: TE7WR902AC.
Specification:
- 650/391/216 MHz (CPU/DDR/AHB)
- 1x 10/100 Mbps Ethernet
- 1x USB 2.0 (GPIO-controlled power)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH
- 2T2R 2.4 GHz (QCA9531)
- 1T1R 5 GHz (QCA9887)
- 5x LED (GPIO-controlled), 2x button, 1x 3-pos switch
- UART pads on PCB (TP1 -> TX, TP2 -> RX, TP3 -> GND, TP4 -> 3V3, jumper
resitors are missing on TX/RX lines)
- 1x micro USB (for power only)
Flash instructions:
Use "factory" image under vendor GUI.
Recovery instructions:
This device contains tftp recovery mode inside U-Boot. You can use it to
flash OpenWrt (use "factory" image) or vendor firmware.
1. Configure PC with static IP 192.168.0.66/24 and tftp server.
2. Rename "openwrt-ath79-generic-tplink_tl-wr902ac-v1-squashfs-factory.bin"
to "wr902acv1_un_tp_recovery.bin" and place it in tftp server dir.
3. Connect PC with LAN port, press the reset button, power up the router
and keep button pressed until WPS LED lights up.
4. Router will download file from server, write it to flash and reboot.
MAC Address summary:
- wlan1 (2.4GHz Wi-Fi): Label MAC
- wlan0 (5GHz Wi-Fi): Offset -1 from label
- eth0 (Wired): Offset +1 from label
Root access over serial line in vendor firmware: root/sohoadmin.
Based on support in ar71xx target by: Piotr Dymacz <pepe2k@gmail.com>
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
[remove size-cells from gpio-export]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-12-01 18:31:32 +00:00
|
|
|
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
2020-09-25 19:52:57 +00:00
|
|
|
|
|
|
|
#include "qca953x.dtsi"
|
ath79: add support for TP-Link TL-WR902AC v1
TP-Link TL-WR902AC v1 is a pocket-size, dual-band (AC750), successor of
TL-MR3020 (both devices use very similar enclosure, in same size). New
device is based on Qualcomm QCA9531 v2 + QCA9887. FCC ID: TE7WR902AC.
Specification:
- 650/391/216 MHz (CPU/DDR/AHB)
- 1x 10/100 Mbps Ethernet
- 1x USB 2.0 (GPIO-controlled power)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH
- 2T2R 2.4 GHz (QCA9531)
- 1T1R 5 GHz (QCA9887)
- 5x LED (GPIO-controlled), 2x button, 1x 3-pos switch
- UART pads on PCB (TP1 -> TX, TP2 -> RX, TP3 -> GND, TP4 -> 3V3, jumper
resitors are missing on TX/RX lines)
- 1x micro USB (for power only)
Flash instructions:
Use "factory" image under vendor GUI.
Recovery instructions:
This device contains tftp recovery mode inside U-Boot. You can use it to
flash OpenWrt (use "factory" image) or vendor firmware.
1. Configure PC with static IP 192.168.0.66/24 and tftp server.
2. Rename "openwrt-ath79-generic-tplink_tl-wr902ac-v1-squashfs-factory.bin"
to "wr902acv1_un_tp_recovery.bin" and place it in tftp server dir.
3. Connect PC with LAN port, press the reset button, power up the router
and keep button pressed until WPS LED lights up.
4. Router will download file from server, write it to flash and reboot.
MAC Address summary:
- wlan1 (2.4GHz Wi-Fi): Label MAC
- wlan0 (5GHz Wi-Fi): Offset -1 from label
- eth0 (Wired): Offset +1 from label
Root access over serial line in vendor firmware: root/sohoadmin.
Based on support in ar71xx target by: Piotr Dymacz <pepe2k@gmail.com>
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
[remove size-cells from gpio-export]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-12-01 18:31:32 +00:00
|
|
|
|
|
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
|
|
#include <dt-bindings/input/input.h>
|
|
|
|
|
|
|
|
/ {
|
|
|
|
compatible = "tplink,tl-wr902ac-v1", "qca,qca9531";
|
|
|
|
model = "TP-Link TL-WR902AC v1";
|
|
|
|
|
|
|
|
aliases {
|
|
|
|
led-boot = &led_power;
|
|
|
|
led-failsafe = &led_power;
|
|
|
|
led-running = &led_power;
|
|
|
|
led-upgrade = &led_power;
|
|
|
|
label-mac-device = &wmac;
|
|
|
|
};
|
|
|
|
|
|
|
|
leds {
|
|
|
|
compatible = "gpio-leds";
|
|
|
|
|
|
|
|
led_power: power {
|
ath79: remove model name from LED labels
Currently, we request LED labels in OpenWrt to follow the scheme
modelname:color:function
However, specifying the modelname at the beginning is actually
entirely useless for the devices we support in OpenWrt. On the
contrary, having this part actually introduces inconvenience in
several aspects:
- We need to ensure/check consistency with the DTS compatible
- We have various exceptions where not the model name is used,
but the vendor name (like tp-link), which is hard to track
and justify even for core-developers
- Having model-based components will not allow to share
identical LED definitions in DTSI files
- The inconsistency in what's used for the model part complicates
several scripts, e.g. board.d/01_leds or LED migrations from
ar71xx where this was even more messy
Apart from our needs, upstream has deprecated the label property
entirely and introduced new properties to specify color and
function properties separately. However, the implementation does
not appear to be ready and probably won't become ready and/or
match our requirements in the foreseeable future.
However, the limitation of generic LEDs to color and function
properties follows the same idea pointed out above. Generic LEDs
will get names like "green:status" or "red:indicator" then, and
if a "devicename" is prepended, it will be the one of an internal
device, like "phy1:amber:status".
With this patch, we move into the same direction, and just drop
the boardname from the LED labels. This allows to consolidate
a few definitions in DTSI files (will be much more on ramips),
and to drop a few migrations compared to ar71xx that just changed
the boardname. But mainly, it will liberate us from a completely
useless subject to take care of for device support review and
maintenance.
To also drop the boardname from existing configurations, a simple
migration routine is added unconditionally.
Although this seems unfamiliar at first look, a quick check in kernel
for the arm/arm64 dts files revealed that while 1033 lines have
labels with three parts *:*:*, still 284 actually use a two-part
labelling *:*, and thus is also acceptable and not even rare there.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-09-26 15:31:17 +00:00
|
|
|
label = "green:power";
|
ath79: add support for TP-Link TL-WR902AC v1
TP-Link TL-WR902AC v1 is a pocket-size, dual-band (AC750), successor of
TL-MR3020 (both devices use very similar enclosure, in same size). New
device is based on Qualcomm QCA9531 v2 + QCA9887. FCC ID: TE7WR902AC.
Specification:
- 650/391/216 MHz (CPU/DDR/AHB)
- 1x 10/100 Mbps Ethernet
- 1x USB 2.0 (GPIO-controlled power)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH
- 2T2R 2.4 GHz (QCA9531)
- 1T1R 5 GHz (QCA9887)
- 5x LED (GPIO-controlled), 2x button, 1x 3-pos switch
- UART pads on PCB (TP1 -> TX, TP2 -> RX, TP3 -> GND, TP4 -> 3V3, jumper
resitors are missing on TX/RX lines)
- 1x micro USB (for power only)
Flash instructions:
Use "factory" image under vendor GUI.
Recovery instructions:
This device contains tftp recovery mode inside U-Boot. You can use it to
flash OpenWrt (use "factory" image) or vendor firmware.
1. Configure PC with static IP 192.168.0.66/24 and tftp server.
2. Rename "openwrt-ath79-generic-tplink_tl-wr902ac-v1-squashfs-factory.bin"
to "wr902acv1_un_tp_recovery.bin" and place it in tftp server dir.
3. Connect PC with LAN port, press the reset button, power up the router
and keep button pressed until WPS LED lights up.
4. Router will download file from server, write it to flash and reboot.
MAC Address summary:
- wlan1 (2.4GHz Wi-Fi): Label MAC
- wlan0 (5GHz Wi-Fi): Offset -1 from label
- eth0 (Wired): Offset +1 from label
Root access over serial line in vendor firmware: root/sohoadmin.
Based on support in ar71xx target by: Piotr Dymacz <pepe2k@gmail.com>
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
[remove size-cells from gpio-export]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-12-01 18:31:32 +00:00
|
|
|
gpios = <&gpio 13 GPIO_ACTIVE_HIGH>;
|
|
|
|
default-state = "on";
|
|
|
|
};
|
|
|
|
|
|
|
|
internet {
|
ath79: remove model name from LED labels
Currently, we request LED labels in OpenWrt to follow the scheme
modelname:color:function
However, specifying the modelname at the beginning is actually
entirely useless for the devices we support in OpenWrt. On the
contrary, having this part actually introduces inconvenience in
several aspects:
- We need to ensure/check consistency with the DTS compatible
- We have various exceptions where not the model name is used,
but the vendor name (like tp-link), which is hard to track
and justify even for core-developers
- Having model-based components will not allow to share
identical LED definitions in DTSI files
- The inconsistency in what's used for the model part complicates
several scripts, e.g. board.d/01_leds or LED migrations from
ar71xx where this was even more messy
Apart from our needs, upstream has deprecated the label property
entirely and introduced new properties to specify color and
function properties separately. However, the implementation does
not appear to be ready and probably won't become ready and/or
match our requirements in the foreseeable future.
However, the limitation of generic LEDs to color and function
properties follows the same idea pointed out above. Generic LEDs
will get names like "green:status" or "red:indicator" then, and
if a "devicename" is prepended, it will be the one of an internal
device, like "phy1:amber:status".
With this patch, we move into the same direction, and just drop
the boardname from the LED labels. This allows to consolidate
a few definitions in DTSI files (will be much more on ramips),
and to drop a few migrations compared to ar71xx that just changed
the boardname. But mainly, it will liberate us from a completely
useless subject to take care of for device support review and
maintenance.
To also drop the boardname from existing configurations, a simple
migration routine is added unconditionally.
Although this seems unfamiliar at first look, a quick check in kernel
for the arm/arm64 dts files revealed that while 1033 lines have
labels with three parts *:*:*, still 284 actually use a two-part
labelling *:*, and thus is also acceptable and not even rare there.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-09-26 15:31:17 +00:00
|
|
|
label = "green:internet";
|
ath79: add support for TP-Link TL-WR902AC v1
TP-Link TL-WR902AC v1 is a pocket-size, dual-band (AC750), successor of
TL-MR3020 (both devices use very similar enclosure, in same size). New
device is based on Qualcomm QCA9531 v2 + QCA9887. FCC ID: TE7WR902AC.
Specification:
- 650/391/216 MHz (CPU/DDR/AHB)
- 1x 10/100 Mbps Ethernet
- 1x USB 2.0 (GPIO-controlled power)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH
- 2T2R 2.4 GHz (QCA9531)
- 1T1R 5 GHz (QCA9887)
- 5x LED (GPIO-controlled), 2x button, 1x 3-pos switch
- UART pads on PCB (TP1 -> TX, TP2 -> RX, TP3 -> GND, TP4 -> 3V3, jumper
resitors are missing on TX/RX lines)
- 1x micro USB (for power only)
Flash instructions:
Use "factory" image under vendor GUI.
Recovery instructions:
This device contains tftp recovery mode inside U-Boot. You can use it to
flash OpenWrt (use "factory" image) or vendor firmware.
1. Configure PC with static IP 192.168.0.66/24 and tftp server.
2. Rename "openwrt-ath79-generic-tplink_tl-wr902ac-v1-squashfs-factory.bin"
to "wr902acv1_un_tp_recovery.bin" and place it in tftp server dir.
3. Connect PC with LAN port, press the reset button, power up the router
and keep button pressed until WPS LED lights up.
4. Router will download file from server, write it to flash and reboot.
MAC Address summary:
- wlan1 (2.4GHz Wi-Fi): Label MAC
- wlan0 (5GHz Wi-Fi): Offset -1 from label
- eth0 (Wired): Offset +1 from label
Root access over serial line in vendor firmware: root/sohoadmin.
Based on support in ar71xx target by: Piotr Dymacz <pepe2k@gmail.com>
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
[remove size-cells from gpio-export]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-12-01 18:31:32 +00:00
|
|
|
gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
|
|
|
|
};
|
|
|
|
|
|
|
|
wlan2g {
|
ath79: remove model name from LED labels
Currently, we request LED labels in OpenWrt to follow the scheme
modelname:color:function
However, specifying the modelname at the beginning is actually
entirely useless for the devices we support in OpenWrt. On the
contrary, having this part actually introduces inconvenience in
several aspects:
- We need to ensure/check consistency with the DTS compatible
- We have various exceptions where not the model name is used,
but the vendor name (like tp-link), which is hard to track
and justify even for core-developers
- Having model-based components will not allow to share
identical LED definitions in DTSI files
- The inconsistency in what's used for the model part complicates
several scripts, e.g. board.d/01_leds or LED migrations from
ar71xx where this was even more messy
Apart from our needs, upstream has deprecated the label property
entirely and introduced new properties to specify color and
function properties separately. However, the implementation does
not appear to be ready and probably won't become ready and/or
match our requirements in the foreseeable future.
However, the limitation of generic LEDs to color and function
properties follows the same idea pointed out above. Generic LEDs
will get names like "green:status" or "red:indicator" then, and
if a "devicename" is prepended, it will be the one of an internal
device, like "phy1:amber:status".
With this patch, we move into the same direction, and just drop
the boardname from the LED labels. This allows to consolidate
a few definitions in DTSI files (will be much more on ramips),
and to drop a few migrations compared to ar71xx that just changed
the boardname. But mainly, it will liberate us from a completely
useless subject to take care of for device support review and
maintenance.
To also drop the boardname from existing configurations, a simple
migration routine is added unconditionally.
Although this seems unfamiliar at first look, a quick check in kernel
for the arm/arm64 dts files revealed that while 1033 lines have
labels with three parts *:*:*, still 284 actually use a two-part
labelling *:*, and thus is also acceptable and not even rare there.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-09-26 15:31:17 +00:00
|
|
|
label = "green:wlan2g";
|
ath79: add support for TP-Link TL-WR902AC v1
TP-Link TL-WR902AC v1 is a pocket-size, dual-band (AC750), successor of
TL-MR3020 (both devices use very similar enclosure, in same size). New
device is based on Qualcomm QCA9531 v2 + QCA9887. FCC ID: TE7WR902AC.
Specification:
- 650/391/216 MHz (CPU/DDR/AHB)
- 1x 10/100 Mbps Ethernet
- 1x USB 2.0 (GPIO-controlled power)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH
- 2T2R 2.4 GHz (QCA9531)
- 1T1R 5 GHz (QCA9887)
- 5x LED (GPIO-controlled), 2x button, 1x 3-pos switch
- UART pads on PCB (TP1 -> TX, TP2 -> RX, TP3 -> GND, TP4 -> 3V3, jumper
resitors are missing on TX/RX lines)
- 1x micro USB (for power only)
Flash instructions:
Use "factory" image under vendor GUI.
Recovery instructions:
This device contains tftp recovery mode inside U-Boot. You can use it to
flash OpenWrt (use "factory" image) or vendor firmware.
1. Configure PC with static IP 192.168.0.66/24 and tftp server.
2. Rename "openwrt-ath79-generic-tplink_tl-wr902ac-v1-squashfs-factory.bin"
to "wr902acv1_un_tp_recovery.bin" and place it in tftp server dir.
3. Connect PC with LAN port, press the reset button, power up the router
and keep button pressed until WPS LED lights up.
4. Router will download file from server, write it to flash and reboot.
MAC Address summary:
- wlan1 (2.4GHz Wi-Fi): Label MAC
- wlan0 (5GHz Wi-Fi): Offset -1 from label
- eth0 (Wired): Offset +1 from label
Root access over serial line in vendor firmware: root/sohoadmin.
Based on support in ar71xx target by: Piotr Dymacz <pepe2k@gmail.com>
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
[remove size-cells from gpio-export]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-12-01 18:31:32 +00:00
|
|
|
gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
|
|
|
|
linux,default-trigger = "phy0tpt";
|
|
|
|
};
|
|
|
|
|
|
|
|
usb {
|
ath79: remove model name from LED labels
Currently, we request LED labels in OpenWrt to follow the scheme
modelname:color:function
However, specifying the modelname at the beginning is actually
entirely useless for the devices we support in OpenWrt. On the
contrary, having this part actually introduces inconvenience in
several aspects:
- We need to ensure/check consistency with the DTS compatible
- We have various exceptions where not the model name is used,
but the vendor name (like tp-link), which is hard to track
and justify even for core-developers
- Having model-based components will not allow to share
identical LED definitions in DTSI files
- The inconsistency in what's used for the model part complicates
several scripts, e.g. board.d/01_leds or LED migrations from
ar71xx where this was even more messy
Apart from our needs, upstream has deprecated the label property
entirely and introduced new properties to specify color and
function properties separately. However, the implementation does
not appear to be ready and probably won't become ready and/or
match our requirements in the foreseeable future.
However, the limitation of generic LEDs to color and function
properties follows the same idea pointed out above. Generic LEDs
will get names like "green:status" or "red:indicator" then, and
if a "devicename" is prepended, it will be the one of an internal
device, like "phy1:amber:status".
With this patch, we move into the same direction, and just drop
the boardname from the LED labels. This allows to consolidate
a few definitions in DTSI files (will be much more on ramips),
and to drop a few migrations compared to ar71xx that just changed
the boardname. But mainly, it will liberate us from a completely
useless subject to take care of for device support review and
maintenance.
To also drop the boardname from existing configurations, a simple
migration routine is added unconditionally.
Although this seems unfamiliar at first look, a quick check in kernel
for the arm/arm64 dts files revealed that while 1033 lines have
labels with three parts *:*:*, still 284 actually use a two-part
labelling *:*, and thus is also acceptable and not even rare there.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-09-26 15:31:17 +00:00
|
|
|
label = "green:usb";
|
ath79: add support for TP-Link TL-WR902AC v1
TP-Link TL-WR902AC v1 is a pocket-size, dual-band (AC750), successor of
TL-MR3020 (both devices use very similar enclosure, in same size). New
device is based on Qualcomm QCA9531 v2 + QCA9887. FCC ID: TE7WR902AC.
Specification:
- 650/391/216 MHz (CPU/DDR/AHB)
- 1x 10/100 Mbps Ethernet
- 1x USB 2.0 (GPIO-controlled power)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH
- 2T2R 2.4 GHz (QCA9531)
- 1T1R 5 GHz (QCA9887)
- 5x LED (GPIO-controlled), 2x button, 1x 3-pos switch
- UART pads on PCB (TP1 -> TX, TP2 -> RX, TP3 -> GND, TP4 -> 3V3, jumper
resitors are missing on TX/RX lines)
- 1x micro USB (for power only)
Flash instructions:
Use "factory" image under vendor GUI.
Recovery instructions:
This device contains tftp recovery mode inside U-Boot. You can use it to
flash OpenWrt (use "factory" image) or vendor firmware.
1. Configure PC with static IP 192.168.0.66/24 and tftp server.
2. Rename "openwrt-ath79-generic-tplink_tl-wr902ac-v1-squashfs-factory.bin"
to "wr902acv1_un_tp_recovery.bin" and place it in tftp server dir.
3. Connect PC with LAN port, press the reset button, power up the router
and keep button pressed until WPS LED lights up.
4. Router will download file from server, write it to flash and reboot.
MAC Address summary:
- wlan1 (2.4GHz Wi-Fi): Label MAC
- wlan0 (5GHz Wi-Fi): Offset -1 from label
- eth0 (Wired): Offset +1 from label
Root access over serial line in vendor firmware: root/sohoadmin.
Based on support in ar71xx target by: Piotr Dymacz <pepe2k@gmail.com>
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
[remove size-cells from gpio-export]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-12-01 18:31:32 +00:00
|
|
|
gpios = <&gpio 4 GPIO_ACTIVE_HIGH>;
|
|
|
|
trigger-sources = <&hub_port0>;
|
|
|
|
linux,default-trigger = "usbport";
|
|
|
|
};
|
|
|
|
|
|
|
|
wps {
|
ath79: remove model name from LED labels
Currently, we request LED labels in OpenWrt to follow the scheme
modelname:color:function
However, specifying the modelname at the beginning is actually
entirely useless for the devices we support in OpenWrt. On the
contrary, having this part actually introduces inconvenience in
several aspects:
- We need to ensure/check consistency with the DTS compatible
- We have various exceptions where not the model name is used,
but the vendor name (like tp-link), which is hard to track
and justify even for core-developers
- Having model-based components will not allow to share
identical LED definitions in DTSI files
- The inconsistency in what's used for the model part complicates
several scripts, e.g. board.d/01_leds or LED migrations from
ar71xx where this was even more messy
Apart from our needs, upstream has deprecated the label property
entirely and introduced new properties to specify color and
function properties separately. However, the implementation does
not appear to be ready and probably won't become ready and/or
match our requirements in the foreseeable future.
However, the limitation of generic LEDs to color and function
properties follows the same idea pointed out above. Generic LEDs
will get names like "green:status" or "red:indicator" then, and
if a "devicename" is prepended, it will be the one of an internal
device, like "phy1:amber:status".
With this patch, we move into the same direction, and just drop
the boardname from the LED labels. This allows to consolidate
a few definitions in DTSI files (will be much more on ramips),
and to drop a few migrations compared to ar71xx that just changed
the boardname. But mainly, it will liberate us from a completely
useless subject to take care of for device support review and
maintenance.
To also drop the boardname from existing configurations, a simple
migration routine is added unconditionally.
Although this seems unfamiliar at first look, a quick check in kernel
for the arm/arm64 dts files revealed that while 1033 lines have
labels with three parts *:*:*, still 284 actually use a two-part
labelling *:*, and thus is also acceptable and not even rare there.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-09-26 15:31:17 +00:00
|
|
|
label = "green:wps";
|
ath79: add support for TP-Link TL-WR902AC v1
TP-Link TL-WR902AC v1 is a pocket-size, dual-band (AC750), successor of
TL-MR3020 (both devices use very similar enclosure, in same size). New
device is based on Qualcomm QCA9531 v2 + QCA9887. FCC ID: TE7WR902AC.
Specification:
- 650/391/216 MHz (CPU/DDR/AHB)
- 1x 10/100 Mbps Ethernet
- 1x USB 2.0 (GPIO-controlled power)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH
- 2T2R 2.4 GHz (QCA9531)
- 1T1R 5 GHz (QCA9887)
- 5x LED (GPIO-controlled), 2x button, 1x 3-pos switch
- UART pads on PCB (TP1 -> TX, TP2 -> RX, TP3 -> GND, TP4 -> 3V3, jumper
resitors are missing on TX/RX lines)
- 1x micro USB (for power only)
Flash instructions:
Use "factory" image under vendor GUI.
Recovery instructions:
This device contains tftp recovery mode inside U-Boot. You can use it to
flash OpenWrt (use "factory" image) or vendor firmware.
1. Configure PC with static IP 192.168.0.66/24 and tftp server.
2. Rename "openwrt-ath79-generic-tplink_tl-wr902ac-v1-squashfs-factory.bin"
to "wr902acv1_un_tp_recovery.bin" and place it in tftp server dir.
3. Connect PC with LAN port, press the reset button, power up the router
and keep button pressed until WPS LED lights up.
4. Router will download file from server, write it to flash and reboot.
MAC Address summary:
- wlan1 (2.4GHz Wi-Fi): Label MAC
- wlan0 (5GHz Wi-Fi): Offset -1 from label
- eth0 (Wired): Offset +1 from label
Root access over serial line in vendor firmware: root/sohoadmin.
Based on support in ar71xx target by: Piotr Dymacz <pepe2k@gmail.com>
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
[remove size-cells from gpio-export]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-12-01 18:31:32 +00:00
|
|
|
gpios = <&gpio 0 GPIO_ACTIVE_LOW>;
|
|
|
|
};
|
|
|
|
|
|
|
|
lan {
|
ath79: remove model name from LED labels
Currently, we request LED labels in OpenWrt to follow the scheme
modelname:color:function
However, specifying the modelname at the beginning is actually
entirely useless for the devices we support in OpenWrt. On the
contrary, having this part actually introduces inconvenience in
several aspects:
- We need to ensure/check consistency with the DTS compatible
- We have various exceptions where not the model name is used,
but the vendor name (like tp-link), which is hard to track
and justify even for core-developers
- Having model-based components will not allow to share
identical LED definitions in DTSI files
- The inconsistency in what's used for the model part complicates
several scripts, e.g. board.d/01_leds or LED migrations from
ar71xx where this was even more messy
Apart from our needs, upstream has deprecated the label property
entirely and introduced new properties to specify color and
function properties separately. However, the implementation does
not appear to be ready and probably won't become ready and/or
match our requirements in the foreseeable future.
However, the limitation of generic LEDs to color and function
properties follows the same idea pointed out above. Generic LEDs
will get names like "green:status" or "red:indicator" then, and
if a "devicename" is prepended, it will be the one of an internal
device, like "phy1:amber:status".
With this patch, we move into the same direction, and just drop
the boardname from the LED labels. This allows to consolidate
a few definitions in DTSI files (will be much more on ramips),
and to drop a few migrations compared to ar71xx that just changed
the boardname. But mainly, it will liberate us from a completely
useless subject to take care of for device support review and
maintenance.
To also drop the boardname from existing configurations, a simple
migration routine is added unconditionally.
Although this seems unfamiliar at first look, a quick check in kernel
for the arm/arm64 dts files revealed that while 1033 lines have
labels with three parts *:*:*, still 284 actually use a two-part
labelling *:*, and thus is also acceptable and not even rare there.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-09-26 15:31:17 +00:00
|
|
|
label = "green:lan";
|
ath79: add support for TP-Link TL-WR902AC v1
TP-Link TL-WR902AC v1 is a pocket-size, dual-band (AC750), successor of
TL-MR3020 (both devices use very similar enclosure, in same size). New
device is based on Qualcomm QCA9531 v2 + QCA9887. FCC ID: TE7WR902AC.
Specification:
- 650/391/216 MHz (CPU/DDR/AHB)
- 1x 10/100 Mbps Ethernet
- 1x USB 2.0 (GPIO-controlled power)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH
- 2T2R 2.4 GHz (QCA9531)
- 1T1R 5 GHz (QCA9887)
- 5x LED (GPIO-controlled), 2x button, 1x 3-pos switch
- UART pads on PCB (TP1 -> TX, TP2 -> RX, TP3 -> GND, TP4 -> 3V3, jumper
resitors are missing on TX/RX lines)
- 1x micro USB (for power only)
Flash instructions:
Use "factory" image under vendor GUI.
Recovery instructions:
This device contains tftp recovery mode inside U-Boot. You can use it to
flash OpenWrt (use "factory" image) or vendor firmware.
1. Configure PC with static IP 192.168.0.66/24 and tftp server.
2. Rename "openwrt-ath79-generic-tplink_tl-wr902ac-v1-squashfs-factory.bin"
to "wr902acv1_un_tp_recovery.bin" and place it in tftp server dir.
3. Connect PC with LAN port, press the reset button, power up the router
and keep button pressed until WPS LED lights up.
4. Router will download file from server, write it to flash and reboot.
MAC Address summary:
- wlan1 (2.4GHz Wi-Fi): Label MAC
- wlan0 (5GHz Wi-Fi): Offset -1 from label
- eth0 (Wired): Offset +1 from label
Root access over serial line in vendor firmware: root/sohoadmin.
Based on support in ar71xx target by: Piotr Dymacz <pepe2k@gmail.com>
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
[remove size-cells from gpio-export]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-12-01 18:31:32 +00:00
|
|
|
gpios = <&gpio 15 GPIO_ACTIVE_HIGH>;
|
|
|
|
};
|
|
|
|
};
|
|
|
|
|
|
|
|
keys {
|
|
|
|
compatible = "gpio-keys";
|
|
|
|
|
|
|
|
reset {
|
|
|
|
label = "Reset button";
|
|
|
|
linux,code = <KEY_RESTART>;
|
|
|
|
gpios = <&gpio 3 GPIO_ACTIVE_LOW>;
|
|
|
|
};
|
|
|
|
|
|
|
|
wps {
|
|
|
|
label = "WPS button";
|
|
|
|
linux,code = <KEY_WPS_BUTTON>;
|
|
|
|
gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
|
|
|
|
};
|
|
|
|
|
|
|
|
sw1 {
|
|
|
|
label = "Mode switch 1";
|
2020-06-20 16:16:11 +00:00
|
|
|
linux,input-type = <EV_SW>;
|
ath79: add support for TP-Link TL-WR902AC v1
TP-Link TL-WR902AC v1 is a pocket-size, dual-band (AC750), successor of
TL-MR3020 (both devices use very similar enclosure, in same size). New
device is based on Qualcomm QCA9531 v2 + QCA9887. FCC ID: TE7WR902AC.
Specification:
- 650/391/216 MHz (CPU/DDR/AHB)
- 1x 10/100 Mbps Ethernet
- 1x USB 2.0 (GPIO-controlled power)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH
- 2T2R 2.4 GHz (QCA9531)
- 1T1R 5 GHz (QCA9887)
- 5x LED (GPIO-controlled), 2x button, 1x 3-pos switch
- UART pads on PCB (TP1 -> TX, TP2 -> RX, TP3 -> GND, TP4 -> 3V3, jumper
resitors are missing on TX/RX lines)
- 1x micro USB (for power only)
Flash instructions:
Use "factory" image under vendor GUI.
Recovery instructions:
This device contains tftp recovery mode inside U-Boot. You can use it to
flash OpenWrt (use "factory" image) or vendor firmware.
1. Configure PC with static IP 192.168.0.66/24 and tftp server.
2. Rename "openwrt-ath79-generic-tplink_tl-wr902ac-v1-squashfs-factory.bin"
to "wr902acv1_un_tp_recovery.bin" and place it in tftp server dir.
3. Connect PC with LAN port, press the reset button, power up the router
and keep button pressed until WPS LED lights up.
4. Router will download file from server, write it to flash and reboot.
MAC Address summary:
- wlan1 (2.4GHz Wi-Fi): Label MAC
- wlan0 (5GHz Wi-Fi): Offset -1 from label
- eth0 (Wired): Offset +1 from label
Root access over serial line in vendor firmware: root/sohoadmin.
Based on support in ar71xx target by: Piotr Dymacz <pepe2k@gmail.com>
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
[remove size-cells from gpio-export]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-12-01 18:31:32 +00:00
|
|
|
linux,code = <BTN_0>;
|
|
|
|
gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
|
|
|
|
};
|
|
|
|
|
|
|
|
sw2 {
|
|
|
|
label = "Mode switch 2";
|
2020-06-20 16:16:11 +00:00
|
|
|
linux,input-type = <EV_SW>;
|
ath79: add support for TP-Link TL-WR902AC v1
TP-Link TL-WR902AC v1 is a pocket-size, dual-band (AC750), successor of
TL-MR3020 (both devices use very similar enclosure, in same size). New
device is based on Qualcomm QCA9531 v2 + QCA9887. FCC ID: TE7WR902AC.
Specification:
- 650/391/216 MHz (CPU/DDR/AHB)
- 1x 10/100 Mbps Ethernet
- 1x USB 2.0 (GPIO-controlled power)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH
- 2T2R 2.4 GHz (QCA9531)
- 1T1R 5 GHz (QCA9887)
- 5x LED (GPIO-controlled), 2x button, 1x 3-pos switch
- UART pads on PCB (TP1 -> TX, TP2 -> RX, TP3 -> GND, TP4 -> 3V3, jumper
resitors are missing on TX/RX lines)
- 1x micro USB (for power only)
Flash instructions:
Use "factory" image under vendor GUI.
Recovery instructions:
This device contains tftp recovery mode inside U-Boot. You can use it to
flash OpenWrt (use "factory" image) or vendor firmware.
1. Configure PC with static IP 192.168.0.66/24 and tftp server.
2. Rename "openwrt-ath79-generic-tplink_tl-wr902ac-v1-squashfs-factory.bin"
to "wr902acv1_un_tp_recovery.bin" and place it in tftp server dir.
3. Connect PC with LAN port, press the reset button, power up the router
and keep button pressed until WPS LED lights up.
4. Router will download file from server, write it to flash and reboot.
MAC Address summary:
- wlan1 (2.4GHz Wi-Fi): Label MAC
- wlan0 (5GHz Wi-Fi): Offset -1 from label
- eth0 (Wired): Offset +1 from label
Root access over serial line in vendor firmware: root/sohoadmin.
Based on support in ar71xx target by: Piotr Dymacz <pepe2k@gmail.com>
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
[remove size-cells from gpio-export]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-12-01 18:31:32 +00:00
|
|
|
linux,code = <BTN_1>;
|
|
|
|
gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
|
|
|
|
};
|
|
|
|
};
|
|
|
|
|
|
|
|
gpio-export {
|
|
|
|
compatible = "gpio-export";
|
|
|
|
|
|
|
|
gpio_usb_power {
|
|
|
|
gpio-export,name = "tp-link:power:usb";
|
|
|
|
gpio-export,output = <1>;
|
|
|
|
gpios = <&gpio 1 GPIO_ACTIVE_HIGH>;
|
|
|
|
};
|
|
|
|
};
|
|
|
|
};
|
|
|
|
|
|
|
|
&spi {
|
|
|
|
status = "okay";
|
|
|
|
|
|
|
|
flash@0 {
|
|
|
|
compatible = "jedec,spi-nor";
|
|
|
|
reg = <0>;
|
|
|
|
spi-max-frequency = <25000000>;
|
|
|
|
|
|
|
|
partitions {
|
|
|
|
compatible = "fixed-partitions";
|
|
|
|
#address-cells = <1>;
|
|
|
|
#size-cells = <1>;
|
|
|
|
|
|
|
|
partition@0 {
|
|
|
|
label = "u-boot";
|
|
|
|
reg = <0x000000 0x020000>;
|
|
|
|
read-only;
|
|
|
|
};
|
|
|
|
|
|
|
|
partition@20000 {
|
|
|
|
compatible = "tplink,firmware";
|
|
|
|
label = "firmware";
|
|
|
|
reg = <0x020000 0x730000>;
|
|
|
|
};
|
|
|
|
|
ath79: consistently use "info" label for default-mac partition
The tp-link safeloader devices typically contain a partition
"default-mac" which stores the MAC addresses. It is followed by other
partitions containing device info, like
{"default-mac", 0x610000, 0x00020},
{"pin", 0x610100, 0x00020},
{"product-info", 0x611100, 0x01000},
In DTS, we typically assign a 0x10000 sized partition for these,
which is mostly labelled "mac" or "info". In rarer cases, the
partitions have been enclosed in a larger "tplink" or "config"
partition.
However, when comparing different devices, the implementation appears
relatively arbitrary at the moment.
Thus, this PR aims at harmonizing these partitions by always using
the name "info" for the DTS partition containing "default-mac".
"info" is preferred over "mac" as we never just have "default-mac"
alone, but always some other device-info partitions as well.
While at it, this also establishes a similar partitioning for the
few devices where the "info" partitions are part of a bigger
unspecific "config" partition or similar.
Besides the harmonization itself, this also allows to merge a few
cases in 11-ath10k-caldata.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-09-12 18:54:04 +00:00
|
|
|
info: partition@750000 {
|
|
|
|
label = "info";
|
|
|
|
reg = <0x750000 0x010000>;
|
|
|
|
read-only;
|
2023-11-09 23:18:44 +00:00
|
|
|
|
|
|
|
nvmem-layout {
|
|
|
|
compatible = "fixed-layout";
|
|
|
|
#address-cells = <1>;
|
|
|
|
#size-cells = <1>;
|
|
|
|
|
|
|
|
macaddr_info_8: macaddr@8 {
|
2023-11-10 22:55:43 +00:00
|
|
|
compatible = "mac-base";
|
2023-11-09 23:18:44 +00:00
|
|
|
reg = <0x8 0x6>;
|
2023-11-10 22:55:43 +00:00
|
|
|
#nvmem-cell-cells = <1>;
|
2023-11-09 23:18:44 +00:00
|
|
|
};
|
|
|
|
};
|
ath79: consistently use "info" label for default-mac partition
The tp-link safeloader devices typically contain a partition
"default-mac" which stores the MAC addresses. It is followed by other
partitions containing device info, like
{"default-mac", 0x610000, 0x00020},
{"pin", 0x610100, 0x00020},
{"product-info", 0x611100, 0x01000},
In DTS, we typically assign a 0x10000 sized partition for these,
which is mostly labelled "mac" or "info". In rarer cases, the
partitions have been enclosed in a larger "tplink" or "config"
partition.
However, when comparing different devices, the implementation appears
relatively arbitrary at the moment.
Thus, this PR aims at harmonizing these partitions by always using
the name "info" for the DTS partition containing "default-mac".
"info" is preferred over "mac" as we never just have "default-mac"
alone, but always some other device-info partitions as well.
While at it, this also establishes a similar partitioning for the
few devices where the "info" partitions are part of a bigger
unspecific "config" partition or similar.
Besides the harmonization itself, this also allows to merge a few
cases in 11-ath10k-caldata.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-09-12 18:54:04 +00:00
|
|
|
};
|
|
|
|
|
|
|
|
partition@760000 {
|
ath79: add support for TP-Link TL-WR902AC v1
TP-Link TL-WR902AC v1 is a pocket-size, dual-band (AC750), successor of
TL-MR3020 (both devices use very similar enclosure, in same size). New
device is based on Qualcomm QCA9531 v2 + QCA9887. FCC ID: TE7WR902AC.
Specification:
- 650/391/216 MHz (CPU/DDR/AHB)
- 1x 10/100 Mbps Ethernet
- 1x USB 2.0 (GPIO-controlled power)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH
- 2T2R 2.4 GHz (QCA9531)
- 1T1R 5 GHz (QCA9887)
- 5x LED (GPIO-controlled), 2x button, 1x 3-pos switch
- UART pads on PCB (TP1 -> TX, TP2 -> RX, TP3 -> GND, TP4 -> 3V3, jumper
resitors are missing on TX/RX lines)
- 1x micro USB (for power only)
Flash instructions:
Use "factory" image under vendor GUI.
Recovery instructions:
This device contains tftp recovery mode inside U-Boot. You can use it to
flash OpenWrt (use "factory" image) or vendor firmware.
1. Configure PC with static IP 192.168.0.66/24 and tftp server.
2. Rename "openwrt-ath79-generic-tplink_tl-wr902ac-v1-squashfs-factory.bin"
to "wr902acv1_un_tp_recovery.bin" and place it in tftp server dir.
3. Connect PC with LAN port, press the reset button, power up the router
and keep button pressed until WPS LED lights up.
4. Router will download file from server, write it to flash and reboot.
MAC Address summary:
- wlan1 (2.4GHz Wi-Fi): Label MAC
- wlan0 (5GHz Wi-Fi): Offset -1 from label
- eth0 (Wired): Offset +1 from label
Root access over serial line in vendor firmware: root/sohoadmin.
Based on support in ar71xx target by: Piotr Dymacz <pepe2k@gmail.com>
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
[remove size-cells from gpio-export]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-12-01 18:31:32 +00:00
|
|
|
label = "tplink";
|
ath79: consistently use "info" label for default-mac partition
The tp-link safeloader devices typically contain a partition
"default-mac" which stores the MAC addresses. It is followed by other
partitions containing device info, like
{"default-mac", 0x610000, 0x00020},
{"pin", 0x610100, 0x00020},
{"product-info", 0x611100, 0x01000},
In DTS, we typically assign a 0x10000 sized partition for these,
which is mostly labelled "mac" or "info". In rarer cases, the
partitions have been enclosed in a larger "tplink" or "config"
partition.
However, when comparing different devices, the implementation appears
relatively arbitrary at the moment.
Thus, this PR aims at harmonizing these partitions by always using
the name "info" for the DTS partition containing "default-mac".
"info" is preferred over "mac" as we never just have "default-mac"
alone, but always some other device-info partitions as well.
While at it, this also establishes a similar partitioning for the
few devices where the "info" partitions are part of a bigger
unspecific "config" partition or similar.
Besides the harmonization itself, this also allows to merge a few
cases in 11-ath10k-caldata.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-09-12 18:54:04 +00:00
|
|
|
reg = <0x760000 0x090000>;
|
ath79: add support for TP-Link TL-WR902AC v1
TP-Link TL-WR902AC v1 is a pocket-size, dual-band (AC750), successor of
TL-MR3020 (both devices use very similar enclosure, in same size). New
device is based on Qualcomm QCA9531 v2 + QCA9887. FCC ID: TE7WR902AC.
Specification:
- 650/391/216 MHz (CPU/DDR/AHB)
- 1x 10/100 Mbps Ethernet
- 1x USB 2.0 (GPIO-controlled power)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH
- 2T2R 2.4 GHz (QCA9531)
- 1T1R 5 GHz (QCA9887)
- 5x LED (GPIO-controlled), 2x button, 1x 3-pos switch
- UART pads on PCB (TP1 -> TX, TP2 -> RX, TP3 -> GND, TP4 -> 3V3, jumper
resitors are missing on TX/RX lines)
- 1x micro USB (for power only)
Flash instructions:
Use "factory" image under vendor GUI.
Recovery instructions:
This device contains tftp recovery mode inside U-Boot. You can use it to
flash OpenWrt (use "factory" image) or vendor firmware.
1. Configure PC with static IP 192.168.0.66/24 and tftp server.
2. Rename "openwrt-ath79-generic-tplink_tl-wr902ac-v1-squashfs-factory.bin"
to "wr902acv1_un_tp_recovery.bin" and place it in tftp server dir.
3. Connect PC with LAN port, press the reset button, power up the router
and keep button pressed until WPS LED lights up.
4. Router will download file from server, write it to flash and reboot.
MAC Address summary:
- wlan1 (2.4GHz Wi-Fi): Label MAC
- wlan0 (5GHz Wi-Fi): Offset -1 from label
- eth0 (Wired): Offset +1 from label
Root access over serial line in vendor firmware: root/sohoadmin.
Based on support in ar71xx target by: Piotr Dymacz <pepe2k@gmail.com>
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
[remove size-cells from gpio-export]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-12-01 18:31:32 +00:00
|
|
|
read-only;
|
|
|
|
};
|
|
|
|
|
|
|
|
art: partition@7f0000 {
|
|
|
|
label = "art";
|
|
|
|
reg = <0x7f0000 0x010000>;
|
|
|
|
read-only;
|
|
|
|
};
|
|
|
|
};
|
|
|
|
};
|
|
|
|
};
|
|
|
|
|
|
|
|
ð0 {
|
|
|
|
status = "okay";
|
|
|
|
|
|
|
|
phy-handle = <&swphy4>;
|
|
|
|
|
2023-11-10 22:55:43 +00:00
|
|
|
nvmem-cells = <&macaddr_info_8 1>;
|
2021-04-02 21:47:31 +00:00
|
|
|
nvmem-cell-names = "mac-address";
|
ath79: add support for TP-Link TL-WR902AC v1
TP-Link TL-WR902AC v1 is a pocket-size, dual-band (AC750), successor of
TL-MR3020 (both devices use very similar enclosure, in same size). New
device is based on Qualcomm QCA9531 v2 + QCA9887. FCC ID: TE7WR902AC.
Specification:
- 650/391/216 MHz (CPU/DDR/AHB)
- 1x 10/100 Mbps Ethernet
- 1x USB 2.0 (GPIO-controlled power)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH
- 2T2R 2.4 GHz (QCA9531)
- 1T1R 5 GHz (QCA9887)
- 5x LED (GPIO-controlled), 2x button, 1x 3-pos switch
- UART pads on PCB (TP1 -> TX, TP2 -> RX, TP3 -> GND, TP4 -> 3V3, jumper
resitors are missing on TX/RX lines)
- 1x micro USB (for power only)
Flash instructions:
Use "factory" image under vendor GUI.
Recovery instructions:
This device contains tftp recovery mode inside U-Boot. You can use it to
flash OpenWrt (use "factory" image) or vendor firmware.
1. Configure PC with static IP 192.168.0.66/24 and tftp server.
2. Rename "openwrt-ath79-generic-tplink_tl-wr902ac-v1-squashfs-factory.bin"
to "wr902acv1_un_tp_recovery.bin" and place it in tftp server dir.
3. Connect PC with LAN port, press the reset button, power up the router
and keep button pressed until WPS LED lights up.
4. Router will download file from server, write it to flash and reboot.
MAC Address summary:
- wlan1 (2.4GHz Wi-Fi): Label MAC
- wlan0 (5GHz Wi-Fi): Offset -1 from label
- eth0 (Wired): Offset +1 from label
Root access over serial line in vendor firmware: root/sohoadmin.
Based on support in ar71xx target by: Piotr Dymacz <pepe2k@gmail.com>
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
[remove size-cells from gpio-export]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-12-01 18:31:32 +00:00
|
|
|
};
|
|
|
|
|
|
|
|
ð1 {
|
|
|
|
compatible = "syscon", "simple-mfd";
|
|
|
|
};
|
|
|
|
|
|
|
|
&wmac {
|
|
|
|
status = "okay";
|
|
|
|
|
|
|
|
mtd-cal-data = <&art 0x1000>;
|
2023-11-10 22:55:43 +00:00
|
|
|
nvmem-cells = <&macaddr_info_8 0>;
|
2021-04-02 21:47:31 +00:00
|
|
|
nvmem-cell-names = "mac-address";
|
ath79: add support for TP-Link TL-WR902AC v1
TP-Link TL-WR902AC v1 is a pocket-size, dual-band (AC750), successor of
TL-MR3020 (both devices use very similar enclosure, in same size). New
device is based on Qualcomm QCA9531 v2 + QCA9887. FCC ID: TE7WR902AC.
Specification:
- 650/391/216 MHz (CPU/DDR/AHB)
- 1x 10/100 Mbps Ethernet
- 1x USB 2.0 (GPIO-controlled power)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH
- 2T2R 2.4 GHz (QCA9531)
- 1T1R 5 GHz (QCA9887)
- 5x LED (GPIO-controlled), 2x button, 1x 3-pos switch
- UART pads on PCB (TP1 -> TX, TP2 -> RX, TP3 -> GND, TP4 -> 3V3, jumper
resitors are missing on TX/RX lines)
- 1x micro USB (for power only)
Flash instructions:
Use "factory" image under vendor GUI.
Recovery instructions:
This device contains tftp recovery mode inside U-Boot. You can use it to
flash OpenWrt (use "factory" image) or vendor firmware.
1. Configure PC with static IP 192.168.0.66/24 and tftp server.
2. Rename "openwrt-ath79-generic-tplink_tl-wr902ac-v1-squashfs-factory.bin"
to "wr902acv1_un_tp_recovery.bin" and place it in tftp server dir.
3. Connect PC with LAN port, press the reset button, power up the router
and keep button pressed until WPS LED lights up.
4. Router will download file from server, write it to flash and reboot.
MAC Address summary:
- wlan1 (2.4GHz Wi-Fi): Label MAC
- wlan0 (5GHz Wi-Fi): Offset -1 from label
- eth0 (Wired): Offset +1 from label
Root access over serial line in vendor firmware: root/sohoadmin.
Based on support in ar71xx target by: Piotr Dymacz <pepe2k@gmail.com>
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
[remove size-cells from gpio-export]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-12-01 18:31:32 +00:00
|
|
|
};
|
|
|
|
|
|
|
|
&pcie0 {
|
|
|
|
status = "okay";
|
|
|
|
|
|
|
|
wifi@0,0 {
|
|
|
|
compatible = "pci168c,0050";
|
|
|
|
reg = <0x0000 0 0 0 0>;
|
|
|
|
};
|
|
|
|
};
|
|
|
|
|
|
|
|
&usb_phy {
|
|
|
|
status = "okay";
|
|
|
|
};
|
|
|
|
|
|
|
|
&usb0 {
|
|
|
|
status = "okay";
|
|
|
|
};
|