openwrt/target/linux/ath79/patches-6.6/911-mikrotik-rb91x.patch

From: Denis Kalashnikov <denis281089@gmail.com>
Subject: [PATCH] ath79: add support for reset key on MikroTik RB912UAG-2HPnD

On MikroTik RB91x board series a reset key shares SoC gpio
line #15 with NAND ALE and NAND IO7. So we need a custom
gpio driver to manage this non-trivial connection schema.
Also rb91x-nand needs to have an ability to disable a polling
of the key while it works with NAND.

While we've been integrating rb91x-key into a firmware, we've
figured out that:
* In the gpio-latch driver we need to add a "cansleep" suffix to
several gpiolib calls,
* When gpio-latch and rb91x-nand fail to get a gpio and an error
is -EPROBE_DEFER, they shouldn't report about this, since this
actually is not an error and occurs when the gpio-latch probe
function is called before the rb91x-key probe.
We fix these related things here too.

Submitted-by: Denis Kalashnikov <denis281089@gmail.com>
Reviewed-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
---
 drivers/gpio/Kconfig                          | 11 +++++++++++
 drivers/gpio/Makefile                         |  2 ++
 drivers/mtd/nand/raw/Kconfig                  |  6 ++++++
 drivers/mtd/nand/raw/Makefile                 |  1 +
 7 files changed, 20 insertions(+)

--- a/drivers/gpio/Kconfig
+++ b/drivers/gpio/Kconfig
@@ -371,6 +371,12 @@ config GPIO_IXP4XX
 
 	  If unsure, say N.
 
+config GPIO_LATCH_MIKROTIK
+	tristate "MikroTik RouterBOARD GPIO latch support"
+	depends on ATH79
+	help
+	  GPIO driver for latch on some MikroTik RouterBOARDs.
+
 config GPIO_LOGICVC
 	tristate "Xylon LogiCVC GPIO support"
 	depends on MFD_SYSCON && OF
@@ -553,6 +559,10 @@ config GPIO_ROCKCHIP
 	help
 	  Say yes here to support GPIO on Rockchip SoCs.
 
+config GPIO_RB91X_KEY
+	tristate "MikroTik RB91x board series reset key support"
+	depends on ATH79
+
 config GPIO_SAMA5D2_PIOBU
 	tristate "SAMA5D2 PIOBU GPIO support"
 	depends on MFD_SYSCON
--- a/drivers/gpio/Makefile
+++ b/drivers/gpio/Makefile
@@ -81,6 +81,7 @@ obj-$(CONFIG_GPIO_IXP4XX)		+= gpio-ixp4x
 obj-$(CONFIG_GPIO_JANZ_TTL)		+= gpio-janz-ttl.o
 obj-$(CONFIG_GPIO_KEMPLD)		+= gpio-kempld.o
 obj-$(CONFIG_GPIO_LATCH)		+= gpio-latch.o
+obj-$(CONFIG_GPIO_LATCH_MIKROTIK)	+= gpio-latch-mikrotik.o
 obj-$(CONFIG_GPIO_LJCA) 		+= gpio-ljca.o
 obj-$(CONFIG_GPIO_LOGICVC)		+= gpio-logicvc.o
 obj-$(CONFIG_GPIO_LOONGSON1)		+= gpio-loongson1.o
@@ -132,6 +133,7 @@ obj-$(CONFIG_GPIO_PMIC_EIC_SPRD)	+= gpio
 obj-$(CONFIG_GPIO_PXA)			+= gpio-pxa.o
 obj-$(CONFIG_GPIO_RASPBERRYPI_EXP)	+= gpio-raspberrypi-exp.o
 obj-$(CONFIG_GPIO_RB4XX)		+= gpio-rb4xx.o
+obj-$(CONFIG_GPIO_RB91X_KEY)		+= gpio-rb91x-key.o
 obj-$(CONFIG_GPIO_RC5T583)		+= gpio-rc5t583.o
 obj-$(CONFIG_GPIO_RCAR)			+= gpio-rcar.o
 obj-$(CONFIG_GPIO_RDA)			+= gpio-rda.o
--- a/drivers/mtd/nand/raw/Kconfig
+++ b/drivers/mtd/nand/raw/Kconfig
@@ -558,4 +558,10 @@ config MTD_NAND_RB4XX
 	  Enables support for the NAND flash chip on Mikrotik Routerboard
 	  RB4xx series.
 
+config MTD_NAND_RB91X
+	tristate "MikroTik RB91x NAND driver support"
+	depends on ATH79 && MTD_RAW_NAND
+	help
+	  Enables support for the NAND flash chip on MikroTik RB91x series.
+
 endif # MTD_RAW_NAND
--- a/drivers/mtd/nand/raw/Makefile
+++ b/drivers/mtd/nand/raw/Makefile
@@ -59,6 +59,7 @@ obj-$(CONFIG_MTD_NAND_PL35X)		+= pl35x-n
 obj-$(CONFIG_MTD_NAND_RENESAS)		+= renesas-nand-controller.o
 obj-$(CONFIG_MTD_NAND_AR934X)		+= ar934x_nand.o
 obj-$(CONFIG_MTD_NAND_RB4XX)		+= nand_rb4xx.o
+obj-$(CONFIG_MTD_NAND_RB91X)		+= rb91x_nand.o
 
 nand-objs := nand_base.o nand_legacy.o nand_bbt.o nand_timings.o nand_ids.o
 nand-objs += nand_onfi.o