openwrt/target/linux/ramips/dts/mt7621_asus_rt-ac57u.dts

149 lines
2.4 KiB
Plaintext
Raw Normal View History

// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
/dts-v1/;
#include "mt7621.dtsi"
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
/ {
compatible = "asus,rt-ac57u", "mediatek,mt7621-soc";
model = "ASUS RT-AC57U";
aliases {
led-boot = &led_power;
led-failsafe = &led_power;
led-running = &led_power;
led-upgrade = &led_power;
};
chosen {
bootargs = "console=ttyS0,57600";
};
leds {
compatible = "gpio-leds";
led_power: power {
label = "rt-ac57u:blue:power";
gpios = <&gpio1 16 GPIO_ACTIVE_LOW>;
};
usb {
label = "rt-ac57u:blue:usb";
gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
trigger-sources = <&ehci_port2>;
linux,default-trigger = "usbport";
};
};
keys {
compatible = "gpio-keys";
wps {
label = "wps";
gpios = <&gpio1 11 GPIO_ACTIVE_HIGH>;
linux,code = <KEY_WPS_BUTTON>;
debounce-interval = <60>;
};
reset {
label = "reset";
gpios = <&gpio1 9 GPIO_ACTIVE_LOW>;
linux,code = <KEY_RESTART>;
debounce-interval = <60>;
};
};
led-regulator {
compatible = "regulator-fixed";
regulator-name = "LED-Power";
gpio = <&gpio1 14 GPIO_ACTIVE_LOW>;
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-always-on;
};
};
&spi0 {
status = "okay";
flash@0 {
compatible = "jedec,spi-nor";
reg = <0>;
spi-max-frequency = <10000000>;
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
partition@0 {
label = "u-boot";
reg = <0x0 0x30000>;
read-only;
};
partition@30000 {
label = "config";
reg = <0x30000 0x10000>;
read-only;
};
factory: partition@40000 {
label = "factory";
reg = <0x40000 0x10000>;
read-only;
};
partition@50000 {
compatible = "denx,uimage";
label = "firmware";
reg = <0x50000 0xfb0000>;
};
};
};
};
&pcie {
status = "okay";
};
&pcie0 {
wifi@0,0 {
compatible = "mediatek,mt76";
reg = <0x0000 0 0 0 0>;
mediatek,mtd-eeprom = <&factory 0x8000>;
led {
led-sources = <2>;
led-active-low;
};
};
};
&pcie1 {
wifi@0,0 {
compatible = "mediatek,mt76";
reg = <0x0000 0 0 0 0>;
mediatek,mtd-eeprom = <&factory 0x0000>;
led {
led-active-low;
};
};
};
&ethernet {
ramips: clean and improve MAC address setup in 02_network This patch removes unnecessary MAC address setup statements in ramips' 02_network by doing several optimizations: 1. For the following devices, lan_mac was set up with mtd_get_mac_binary although the same address was set in DTS. The lan_mac statement is removed in 02_network, but wan_mac is kept: - mercury,mac1200r-v2 - phicomm,k2g - skylab,skw92a - wiznet,wizfi630a 2. For the following devices, wan_mac was set up with mtd_get_mac_binary although the same address was set in DTS. The wan_mac statement is removed in 02_network, no lan_mac is present: - buffalo,whr-g300n - glinet,gl-mt300n-v2 - zyxel,keenetic-start 3. For the following device, lan_mac and wan_mac were set up with mtd_get_mac_binary to the same address as set in DTS. Both statements are removed in 02_network: - buffalo,whr-600d 4. For some devices, it was possible to move setup from 02_network to DTS by introducing previously missing mtd_mac_address: - buffalo,whr-1166d - buffalo,whr-300hp2 - buffalo,wsr-600dhp - ohyeah,oy-0001 - planex,vr500 5. For one device, mtd_mac_address was just wrong and overwritten by 02_network. Put the correct value in DTS and remove redundant statement in 02_network: - asus,rt-ac57u 6. For one device, MAC address defined in DTS is exchanged together with lan_mac/wan_mac setup in 02_network, so that cases in 02_network can be merged: - phicomm,k2p For some devices, an empty case has to be used to prevent them from falling into the default case and have WAN address = eth0 address + 1 set to them. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-08-12 11:21:05 +00:00
mtd-mac-address = <&factory 0xe000>;
};
&pinctrl {
state_default: pinctrl0 {
gpio {
ralink,group = "sdhci";
ralink,function = "gpio";
};
};
};