ExternalVendorCode/openwrt
1
0
Fork 0
mirror of https://github.com/openwrt/openwrt.git synced 2024-12-20 14:13:16 +00:00
Code Issues Actions 1 Packages Projects Releases Wiki Activity
56716b578e
openwrt/target/linux/ath79/dts/qca9563_tplink_tl-wpa8630p-v2.0-eu.dts

79 lines
1.2 KiB
Plaintext
Raw Normal View History

ath79: add support for TP-Link TL-WPA8630P v2 The TL-WPA8630P v2 is a HomePlug AV2 compatible device with a QCA9563 SoC and 2.4GHz and 5GHz WiFi modules. Specifications -------------- - QCA9563 750MHz, 2.4GHz WiFi - QCA9888 5GHz WiFi - 8MiB SPI Flash - 128MiB RAM - 3 GBit Ports (QCA8337) - PLC (QCA7550) MAC address assignment ---------------------- WiFi 2.4GHz and LAN share the same MAC address as printed on the label. 5GHz WiFi uses LAN-1, based on assumptions from similar devices. LAN Port assignment ------------------- While there are 3 physical LAN ports on the device, there will be 4 visible ports in OpenWrt. The fourth port (internal port 5) is used by the PowerLine Communication SoC and thus treated like a regular LAN port. Versions -------- Note that both TL-WPA8630 and TL-WPA8630P, as well as the different country-versions, differ in partitioning, and therefore shouldn't be cross-flashed. This adds support for the two known partitioning variants of the TL-WPA8630P, where the variants can be safely distinguished via the tplink-safeloader SupportList. For the non-P variants (TL-WPA8630), at least two additional partitioning schemes exist, and the same SupportList entry can have different partitioning. Thus, we don't support those officially (yet). Also note that the P version for Germany (DE) requires the international image version, but is properly protected by SupportList. In any case, please check the OpenWrt Wiki pages for the device before flashing anything! Installation ------------ Installation is possible from the OEM web interface. Make sure to install the latest OEM firmware first, so that the PLC firmware is at the latest version. However, please also check the Wiki page for hints according to altered partitioning between OEM firmware revisions. Additional thanks to Jon Davies and Joe Mullally for bringing order into the partitioning mess. Signed-off-by: Andreas Böhler <dev@aboehler.at> [minor DTS adjustments, add label-mac-device, drop chosen, move common partitions to DTSI, rename de to int, add AU support strings, adjust TPLINK_BOARD_ID, create common node in generic-tp-link.mk, adjust commit message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-03-14 23:20:22 +00:00
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
ath79: convert remaining mtd-mac-address cases to nvmem Since the nvmem-based approach for retrieving MAC addresses appears to depend on the addresses being set up after the partitions, it is no longer possible to keep the MAC address setup in shared DTSI files while the partitions itself are set up in DTS files for the individual devices. In ath79 the firmware partition is typically located somewhere "in the middle" of the partition table. Thus, it's not trivial to share the partitions containing MAC address information in a common DTSI (like we did in some cases on ramips). In this commit, MAC address setup is thus moved to the relevant partitions, and in most cases needs to be duplicated. While the duplication is not really nice, it eventually provides a cleaner and more tidy setup, making the DTS(I) file fragmentation a bit more logical. This should also help with adding new devices, as information is distributed across less locations. For consistency, this commit also moves the mtd-cal-data property "down" together with the MAC address setup, so it's not based on a partition before the latter is defined either. (This is only done for those files touched due to nvmem conversion.) Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-08-18 18:06:29 +00:00
#include "qca9563_tplink_tl-wpa8630.dtsi"
ath79: add support for TP-Link TL-WPA8630P v2 The TL-WPA8630P v2 is a HomePlug AV2 compatible device with a QCA9563 SoC and 2.4GHz and 5GHz WiFi modules. Specifications -------------- - QCA9563 750MHz, 2.4GHz WiFi - QCA9888 5GHz WiFi - 8MiB SPI Flash - 128MiB RAM - 3 GBit Ports (QCA8337) - PLC (QCA7550) MAC address assignment ---------------------- WiFi 2.4GHz and LAN share the same MAC address as printed on the label. 5GHz WiFi uses LAN-1, based on assumptions from similar devices. LAN Port assignment ------------------- While there are 3 physical LAN ports on the device, there will be 4 visible ports in OpenWrt. The fourth port (internal port 5) is used by the PowerLine Communication SoC and thus treated like a regular LAN port. Versions -------- Note that both TL-WPA8630 and TL-WPA8630P, as well as the different country-versions, differ in partitioning, and therefore shouldn't be cross-flashed. This adds support for the two known partitioning variants of the TL-WPA8630P, where the variants can be safely distinguished via the tplink-safeloader SupportList. For the non-P variants (TL-WPA8630), at least two additional partitioning schemes exist, and the same SupportList entry can have different partitioning. Thus, we don't support those officially (yet). Also note that the P version for Germany (DE) requires the international image version, but is properly protected by SupportList. In any case, please check the OpenWrt Wiki pages for the device before flashing anything! Installation ------------ Installation is possible from the OEM web interface. Make sure to install the latest OEM firmware first, so that the PLC firmware is at the latest version. However, please also check the Wiki page for hints according to altered partitioning between OEM firmware revisions. Additional thanks to Jon Davies and Joe Mullally for bringing order into the partitioning mess. Signed-off-by: Andreas Böhler <dev@aboehler.at> [minor DTS adjustments, add label-mac-device, drop chosen, move common partitions to DTSI, rename de to int, add AU support strings, adjust TPLINK_BOARD_ID, create common node in generic-tp-link.mk, adjust commit message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-03-14 23:20:22 +00:00
/ {
ath79: rename TP-Link TL-WPA8630P v2 (EU) to v2.0 (EU) Since we have a v2.1 (EU) with different partitioning now, rename the v2.0 to make the difference visible to the user more directly. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-09-28 12:31:02 +00:00
compatible = "tplink,tl-wpa8630p-v2.0-eu", "qca,qca9563";
model = "TP-Link WPA8630P v2.0 (EU)";
ath79: convert remaining mtd-mac-address cases to nvmem Since the nvmem-based approach for retrieving MAC addresses appears to depend on the addresses being set up after the partitions, it is no longer possible to keep the MAC address setup in shared DTSI files while the partitions itself are set up in DTS files for the individual devices. In ath79 the firmware partition is typically located somewhere "in the middle" of the partition table. Thus, it's not trivial to share the partitions containing MAC address information in a common DTSI (like we did in some cases on ramips). In this commit, MAC address setup is thus moved to the relevant partitions, and in most cases needs to be duplicated. While the duplication is not really nice, it eventually provides a cleaner and more tidy setup, making the DTS(I) file fragmentation a bit more logical. This should also help with adding new devices, as information is distributed across less locations. For consistency, this commit also moves the mtd-cal-data property "down" together with the MAC address setup, so it's not based on a partition before the latter is defined either. (This is only done for those files touched due to nvmem conversion.) Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-08-18 18:06:29 +00:00
aliases {
label-mac-device = &eth0;
};
ath79: add support for TP-Link TL-WPA8630P v2 The TL-WPA8630P v2 is a HomePlug AV2 compatible device with a QCA9563 SoC and 2.4GHz and 5GHz WiFi modules. Specifications -------------- - QCA9563 750MHz, 2.4GHz WiFi - QCA9888 5GHz WiFi - 8MiB SPI Flash - 128MiB RAM - 3 GBit Ports (QCA8337) - PLC (QCA7550) MAC address assignment ---------------------- WiFi 2.4GHz and LAN share the same MAC address as printed on the label. 5GHz WiFi uses LAN-1, based on assumptions from similar devices. LAN Port assignment ------------------- While there are 3 physical LAN ports on the device, there will be 4 visible ports in OpenWrt. The fourth port (internal port 5) is used by the PowerLine Communication SoC and thus treated like a regular LAN port. Versions -------- Note that both TL-WPA8630 and TL-WPA8630P, as well as the different country-versions, differ in partitioning, and therefore shouldn't be cross-flashed. This adds support for the two known partitioning variants of the TL-WPA8630P, where the variants can be safely distinguished via the tplink-safeloader SupportList. For the non-P variants (TL-WPA8630), at least two additional partitioning schemes exist, and the same SupportList entry can have different partitioning. Thus, we don't support those officially (yet). Also note that the P version for Germany (DE) requires the international image version, but is properly protected by SupportList. In any case, please check the OpenWrt Wiki pages for the device before flashing anything! Installation ------------ Installation is possible from the OEM web interface. Make sure to install the latest OEM firmware first, so that the PLC firmware is at the latest version. However, please also check the Wiki page for hints according to altered partitioning between OEM firmware revisions. Additional thanks to Jon Davies and Joe Mullally for bringing order into the partitioning mess. Signed-off-by: Andreas Böhler <dev@aboehler.at> [minor DTS adjustments, add label-mac-device, drop chosen, move common partitions to DTSI, rename de to int, add AU support strings, adjust TPLINK_BOARD_ID, create common node in generic-tp-link.mk, adjust commit message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-03-14 23:20:22 +00:00
};
&partitions {
ath79: convert remaining mtd-mac-address cases to nvmem Since the nvmem-based approach for retrieving MAC addresses appears to depend on the addresses being set up after the partitions, it is no longer possible to keep the MAC address setup in shared DTSI files while the partitions itself are set up in DTS files for the individual devices. In ath79 the firmware partition is typically located somewhere "in the middle" of the partition table. Thus, it's not trivial to share the partitions containing MAC address information in a common DTSI (like we did in some cases on ramips). In this commit, MAC address setup is thus moved to the relevant partitions, and in most cases needs to be duplicated. While the duplication is not really nice, it eventually provides a cleaner and more tidy setup, making the DTS(I) file fragmentation a bit more logical. This should also help with adding new devices, as information is distributed across less locations. For consistency, this commit also moves the mtd-cal-data property "down" together with the MAC address setup, so it's not based on a partition before the latter is defined either. (This is only done for those files touched due to nvmem conversion.) Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-08-18 18:06:29 +00:00
partition@0 {
label = "factory-uboot";
reg = <0x000000 0x020000>;
read-only;
};
partition@20000 {
label = "u-boot";
reg = <0x020000 0x020000>;
read-only;
};
partition@40000 {
compatible = "tplink,firmware";
label = "firmware";
reg = <0x040000 0x5e0000>;
};
ath79: add support for TP-Link TL-WPA8630P (EU) v2.1 This adds support for the TP-Link TL-WPA8630P (EU) in its v2.1 version. The only unique aspect for the firmware compared to v2 layout is the partition layout. Note that while the EU version has different partitioning for v2.0 and v2.1, the v2.1 (AU) is supported by the v2-int image. If you plan to use this device, make sure you have a look at the Wiki page to check whether the device is supported and which image needs to be taken. Specifications -------------- - QCA9563 750MHz, 2.4GHz WiFi - QCA9888 5GHz WiFi - 8MiB SPI Flash - 128MiB RAM - 3 GBit Ports (QCA8337) - PLC (QCA7550) Installation ------------ Installation is possible from the OEM web interface. Make sure to install the latest OEM firmware first, so that the PLC firmware is at the latest version. However, please also check the Wiki page for hints according to altered partitioning between OEM firmware revisions. Notes ----- The OEM firmware has 0x620000 to 0x680000 unassigned, so we leave this empty as well. It is complicated enough already ... Signed-off-by: Joe Mullally <jwmullally@gmail.com> [improve partitions, use v2 DTSI, add entry in 02_network, rewrite and extend commit message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-09-12 18:46:28 +00:00
partition@620000 {
label = "partition-table";
reg = <0x620000 0x010000>;
read-only;
};
ath79: consistently use "info" label for default-mac partition The tp-link safeloader devices typically contain a partition "default-mac" which stores the MAC addresses. It is followed by other partitions containing device info, like {"default-mac", 0x610000, 0x00020}, {"pin", 0x610100, 0x00020}, {"product-info", 0x611100, 0x01000}, In DTS, we typically assign a 0x10000 sized partition for these, which is mostly labelled "mac" or "info". In rarer cases, the partitions have been enclosed in a larger "tplink" or "config" partition. However, when comparing different devices, the implementation appears relatively arbitrary at the moment. Thus, this PR aims at harmonizing these partitions by always using the name "info" for the DTS partition containing "default-mac". "info" is preferred over "mac" as we never just have "default-mac" alone, but always some other device-info partitions as well. While at it, this also establishes a similar partitioning for the few devices where the "info" partitions are part of a bigger unspecific "config" partition or similar. Besides the harmonization itself, this also allows to merge a few cases in 11-ath10k-caldata. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-09-12 18:54:04 +00:00
info: partition@630000 {
label = "info";
ath79: add support for TP-Link TL-WPA8630P v2 The TL-WPA8630P v2 is a HomePlug AV2 compatible device with a QCA9563 SoC and 2.4GHz and 5GHz WiFi modules. Specifications -------------- - QCA9563 750MHz, 2.4GHz WiFi - QCA9888 5GHz WiFi - 8MiB SPI Flash - 128MiB RAM - 3 GBit Ports (QCA8337) - PLC (QCA7550) MAC address assignment ---------------------- WiFi 2.4GHz and LAN share the same MAC address as printed on the label. 5GHz WiFi uses LAN-1, based on assumptions from similar devices. LAN Port assignment ------------------- While there are 3 physical LAN ports on the device, there will be 4 visible ports in OpenWrt. The fourth port (internal port 5) is used by the PowerLine Communication SoC and thus treated like a regular LAN port. Versions -------- Note that both TL-WPA8630 and TL-WPA8630P, as well as the different country-versions, differ in partitioning, and therefore shouldn't be cross-flashed. This adds support for the two known partitioning variants of the TL-WPA8630P, where the variants can be safely distinguished via the tplink-safeloader SupportList. For the non-P variants (TL-WPA8630), at least two additional partitioning schemes exist, and the same SupportList entry can have different partitioning. Thus, we don't support those officially (yet). Also note that the P version for Germany (DE) requires the international image version, but is properly protected by SupportList. In any case, please check the OpenWrt Wiki pages for the device before flashing anything! Installation ------------ Installation is possible from the OEM web interface. Make sure to install the latest OEM firmware first, so that the PLC firmware is at the latest version. However, please also check the Wiki page for hints according to altered partitioning between OEM firmware revisions. Additional thanks to Jon Davies and Joe Mullally for bringing order into the partitioning mess. Signed-off-by: Andreas Böhler <dev@aboehler.at> [minor DTS adjustments, add label-mac-device, drop chosen, move common partitions to DTSI, rename de to int, add AU support strings, adjust TPLINK_BOARD_ID, create common node in generic-tp-link.mk, adjust commit message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-03-14 23:20:22 +00:00
reg = <0x630000 0x010000>;
read-only;
};
partition@640000 {
label = "tplink";
reg = <0x640000 0x1b0000>;
read-only;
};
art: partition@7f0000 {
label = "art";
reg = <0x7f0000 0x010000>;
read-only;
};
};
ath79: convert remaining mtd-mac-address cases to nvmem Since the nvmem-based approach for retrieving MAC addresses appears to depend on the addresses being set up after the partitions, it is no longer possible to keep the MAC address setup in shared DTSI files while the partitions itself are set up in DTS files for the individual devices. In ath79 the firmware partition is typically located somewhere "in the middle" of the partition table. Thus, it's not trivial to share the partitions containing MAC address information in a common DTSI (like we did in some cases on ramips). In this commit, MAC address setup is thus moved to the relevant partitions, and in most cases needs to be duplicated. While the duplication is not really nice, it eventually provides a cleaner and more tidy setup, making the DTS(I) file fragmentation a bit more logical. This should also help with adding new devices, as information is distributed across less locations. For consistency, this commit also moves the mtd-cal-data property "down" together with the MAC address setup, so it's not based on a partition before the latter is defined either. (This is only done for those files touched due to nvmem conversion.) Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-08-18 18:06:29 +00:00
&eth0 {
nvmem-cells = <&macaddr_info_8>;
nvmem-cell-names = "mac-address";
};
&wmac {
mtd-cal-data = <&art 0x1000>;
nvmem-cells = <&macaddr_info_8>;
nvmem-cell-names = "mac-address";
};
&info {
compatible = "nvmem-cells";
#address-cells = <1>;
#size-cells = <1>;
macaddr_info_8: macaddr@8 {
reg = <0x8 0x6>;
};
};
Reference in New Issue Copy Permalink