openwrt/target/linux/realtek/profiles/00-default.mk

# SPDX-License-Identifier: GPL-2.0-only

define Profile/Default
	NAME:=Default Profile
	PRIORITY:=1
endef

define Profile/Default/Description
	Default package set compatible with most boards.
endef

$(eval $(call Profile,Default))
target: use SPDX license identifiers on Makefiles Use SPDX license tags to allow machines to check licenses. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> 2021-02-10 13:52:34 +00:00			`# SPDX-License-Identifier: GPL-2.0-only`
rtl838x: add new architecture This adds support for the RTL838x Architecture. SoCs of this type are used in managed and un-managed Switches and Routers with 8-28 ports. Drivers are provided for SoC initialization, GPIOs, Flash, Ethernet including a DSA switch driver and internal and external PHYs used with these switches. Supported SoCs: RTL8380M RTL8381M RTL8382M The kernel will also boot on the following RTL839x SoCs, however driver support apart from spi-nor is missing: RTL8390 RTL8391 RTL8393 The following PHYs are supported: RTL8214FC (Quad QSGMII multiplexing GMAC and SFP port) RTL8218B internal: internal PHY of the RTL838x chips RTL8318b external (QSGMII 8-port GMAC phy) RTL8382M SerDes for 2 SFP ports Initialization sequences for the PHYs are provided in the form of firmware files. Flash driver supports 3 / 4 byte access DSA switch driver supports VLANs, port isolation, STP and port mirroring. The ALLNET ALL-SG8208M is supported as Proof of Concept: RTL8382M SoC 1 MIPS 4KEc core @ 500MHz 8 Internal PHYs (RTL8218B) 128MB DRAM (Nanya NT5TU128MB) 16MB NOR Flash (MXIC 25L128) 8 GBEthernet ports with one green status LED each (SoC controlled) 1 Power LED (not configurable) 1 SYS LED (configurable) 1 On-Off switch (not configurable) 1 Reset button at the right behind right air-vent (not configurable) 1 Reset button on front panel (configurable) 12V 1A barrel connector 1 serial header with populated standard pin connector and with markings GND TX RX Vcc(3.3V), connection properties: 115200 8N1 To install, upload the sysupgrade image to the OEM webpage. Signed-off-by: Birger Koblitz <git@birger-koblitz.de> 2020-09-13 07:06:13 +00:00
			`define Profile/Default`
			`NAME:=Default Profile`
			`PRIORITY:=1`
			`endef`

			`define Profile/Default/Description`
			`Default package set compatible with most boards.`
			`endef`
rtl838x: remove and add some empty lines Do some minor empty lines cleanup, i.e. remove those at EOF and add some for cosmetic reasons/consistency. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> 2020-09-15 10:28:43 +00:00
rtl838x: add new architecture This adds support for the RTL838x Architecture. SoCs of this type are used in managed and un-managed Switches and Routers with 8-28 ports. Drivers are provided for SoC initialization, GPIOs, Flash, Ethernet including a DSA switch driver and internal and external PHYs used with these switches. Supported SoCs: RTL8380M RTL8381M RTL8382M The kernel will also boot on the following RTL839x SoCs, however driver support apart from spi-nor is missing: RTL8390 RTL8391 RTL8393 The following PHYs are supported: RTL8214FC (Quad QSGMII multiplexing GMAC and SFP port) RTL8218B internal: internal PHY of the RTL838x chips RTL8318b external (QSGMII 8-port GMAC phy) RTL8382M SerDes for 2 SFP ports Initialization sequences for the PHYs are provided in the form of firmware files. Flash driver supports 3 / 4 byte access DSA switch driver supports VLANs, port isolation, STP and port mirroring. The ALLNET ALL-SG8208M is supported as Proof of Concept: RTL8382M SoC 1 MIPS 4KEc core @ 500MHz 8 Internal PHYs (RTL8218B) 128MB DRAM (Nanya NT5TU128MB) 16MB NOR Flash (MXIC 25L128) 8 GBEthernet ports with one green status LED each (SoC controlled) 1 Power LED (not configurable) 1 SYS LED (configurable) 1 On-Off switch (not configurable) 1 Reset button at the right behind right air-vent (not configurable) 1 Reset button on front panel (configurable) 12V 1A barrel connector 1 serial header with populated standard pin connector and with markings GND TX RX Vcc(3.3V), connection properties: 115200 8N1 To install, upload the sysupgrade image to the OEM webpage. Signed-off-by: Birger Koblitz <git@birger-koblitz.de> 2020-09-13 07:06:13 +00:00			`$(eval $(call Profile,Default))`